linux/drivers/clocksource/Makefile

obj-$(CONFIG_ATMEL_TCB_CLKSRC)	+= tcb_clksrc.o
obj-$(CONFIG_X86_CYCLONE_TIMER)	+= cyclone.o
obj-$(CONFIG_X86_PM_TIMER)	+= acpi_pm.o
obj-$(CONFIG_SCx200HR_TIMER)	+= scx200_hrt.o
obj-$(CONFIG_SH_TIMER_CMT)	+= sh_cmt.o
obj-$(CONFIG_SH_TIMER_MTU2)	+= sh_mtu2.o
obj-$(CONFIG_SH_TIMER_TMU)	+= sh_tmu.o
atmel_tc clocksource/clockevent code Clocksource and clockevent device based on the Atmel TC blocks. The clockevent device handles both periodic and oneshot modes, so this enables NO_HZ and high res timers on some platforms that previously couldn't use those mechanisms. This works on both AVR32 and AT91 chips, given relevant patches for tclib support (always) and clockevents (or else this will only look like a higher precision clocksource). It's an updated and modularized version of an AT91-only patch that has circulated for some time now. Changes relative to the original patch: * Update to use new tclib API * Replace open-coded do-while loop using goto with a real do-while loop * Minor irq handler optimization: Load register base address from dev_id instead of a global variable. * Aggressively turn off clocks when the clockevent isn't being used * Include the clockevent code on AT91RM9200 as well. The rating is lower than the System Timer, so the clock will usually stay off. * Don't assume that the number of clocks is always equal to the number of irqs. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> 2008-02-23 01:28:37 +00:00			`obj-$(CONFIG_ATMEL_TCB_CLKSRC) += tcb_clksrc.o`
[PATCH] GTOD: add scx200 HRT clocksource Add a GTOD clocksource driver based on the Geode SCx200's Hi-Res Timer. Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: john stultz <johnstul@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org> 2006-06-26 07:25:19 +00:00			`obj-$(CONFIG_X86_CYCLONE_TIMER) += cyclone.o`
			`obj-$(CONFIG_X86_PM_TIMER) += acpi_pm.o`
			`obj-$(CONFIG_SCx200HR_TIMER) += scx200_hrt.o`
sh: CMT clockevent platform driver SuperH CMT clockevent driver. Both 16-bit and 32-bit CMT versions are supported, but only 32-bit is tested. This driver contains support for both clockevents and clocksources, but no unregistration is supported at this point. Works fine as clock source and/or event in periodic or oneshot mode. Tested on sh7722 and sh7723, but should work with any cpu/architecture. This version is lacking clocksource and early platform driver support for now - this to minimize the amount of dependencies. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org> 2009-01-22 09:55:59 +00:00			`obj-$(CONFIG_SH_TIMER_CMT) += sh_cmt.o`
clocksource: SuperH MTU2 Timer driver This patch adds a MTU2 driver for the SuperH architecture. The MTU2 driver is a platform driver with early platform support to allow using a MTU2 channel as only clockevent during system bootup. Clocksource on sh2a is currently unsupported due to code generation issues with 64-bit math, so at this point only periodic clockevent support is in place. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org> 2009-04-30 07:02:49 +00:00			`obj-$(CONFIG_SH_TIMER_MTU2) += sh_mtu2.o`
clocksource: SuperH TMU Timer driver This patch adds a TMU driver for the SuperH architecture. The TMU driver is a platform driver with early platform support to allow using a TMU channel as clockevent or clocksource during system bootup or later. Clocksource or clockevent can be selected. Both periodic and oneshot clockevents are supported. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org> 2009-05-01 06:51:00 +00:00			`obj-$(CONFIG_SH_TIMER_TMU) += sh_tmu.o`