linux/net/nfc/nci/Makefile

#
# Makefile for the Linux NFC NCI layer.
#

obj-$(CONFIG_NFC_NCI) += nci.o

nci-objs := core.o data.o lib.o ntf.o rsp.o hci.o

nci_spi-y += spi.o
obj-$(CONFIG_NFC_NCI_SPI) += nci_spi.o

nci_uart-y += uart.o
obj-$(CONFIG_NFC_NCI_UART) += nci_uart.o
NFC: basic NCI protocol implementation The NFC Controller Interface (NCI) is a standard communication protocol between an NFC Controller (NFCC) and a Device Host (DH), defined by the NFC Forum. Signed-off-by: Ilan Elias <ilane@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> 2011-09-18 11:19:35 +03:00			`#`
			`# Makefile for the Linux NFC NCI layer.`
			`#`

			`obj-$(CONFIG_NFC_NCI) += nci.o`

NFC: nci: Add HCI over NCI protocol support According to the NCI specification, one can use HCI over NCI to talk with specific NFCEE. The HCI network is viewed as one logical NFCEE. This is needed to support secure element running HCI only firmwares embedded on an NCI capable chipset, like e.g. the st21nfcb. There is some duplication between this piece of code and the HCI core code, but the latter would need to be abstracted even more to be able to use NCI as a logical transport for HCP packets. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> 2015-02-01 22:26:14 +01:00			`nci-objs := core.o data.o lib.o ntf.o rsp.o hci.o`
NFC: Add basic NCI over SPI The NFC Forum defines a transport interface based on Serial Peripheral Interface (SPI) for the NFC Controller Interface (NCI). This module implements the SPI transport of NCI, calling SPI module directly to read/write data to NFC controller (NFCC). NFCC driver should provide functions performing device open and close. It should also provide functions asserting/de-asserting interruption to prevent TX/RX race conditions. NFCC driver can also fix a delay between transactions if needed by the hardware. Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> 2013-05-29 15:35:02 +02:00
NFC: NCI: move generic spi driver to a module SPI driver should be a module. Signed-off-by: Vincent Cuissard <cuissard@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> 2015-10-26 10:27:42 +01:00			`nci_spi-y += spi.o`
			`obj-$(CONFIG_NFC_NCI_SPI) += nci_spi.o`
NFC: nci: add generic uart support Some NFC controller supports UART as host interface. As with SPI, a lot of code can be shared between vendor drivers. This patch add the generic support of UART and provides some extension API for vendor specific needs. This code is strongly inspired by the Bluetooth HCI ldisc implementation. NCI UART vendor drivers will have to register themselves to this layer via nci_uart_register. Underlying tty will have to be configured from user land thanks to an ioctl. Signed-off-by: Vincent Cuissard <cuissard@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> 2015-06-11 11:25:47 +02:00
			`nci_uart-y += uart.o`
			`obj-$(CONFIG_NFC_NCI_UART) += nci_uart.o`