Merge remote-tracking branches 'spi/topic/spidev', 'spi/topic/st-ssc4' and 'spi/topic/stm32' into spi-next

Documentation/devicetree/bindings/spi/spi-stm32.txt

@@ -0,0 +1,59 @@
+STMicroelectronics STM32 SPI Controller
+
+The STM32 SPI controller is used to communicate with external devices using
+the Serial Peripheral Interface. It supports full-duplex, half-duplex and
+simplex synchronous serial communication with external devices. It supports
+from 4 to 32-bit data size. Although it can be configured as master or slave,
+only master is supported by the driver.
+
+Required properties:
+- compatible: Must be "st,stm32h7-spi".
+- reg: Offset and length of the device's register set.
+- interrupts: Must contain the interrupt id.
+- clocks: Must contain an entry for spiclk (which feeds the internal clock
+	  generator).
+- #address-cells:  Number of cells required to define a chip select address.
+- #size-cells: Should be zero.
+
+Optional properties:
+- resets: Must contain the phandle to the reset controller.
+- A pinctrl state named "default" may be defined to set pins in mode of
+  operation for SPI transfer.
+- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the
+  STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt.
+- dma-names: DMA request names should include "tx" and "rx" if present.
+- cs-gpios: list of GPIO chip selects. See the SPI bus bindings,
+  Documentation/devicetree/bindings/spi/spi-bus.txt
+
+
+Child nodes represent devices on the SPI bus
+  See ../spi/spi-bus.txt
+
+Optional properties:
+- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in
+		  nanoseconds inserted between two consecutive data frames.
+
+
+Example:
+	spi2: spi@40003800 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "st,stm32h7-spi";
+		reg = <0x40003800 0x400>;
+		interrupts = <36>;
+		clocks = <&rcc SPI2_CK>;
+		resets = <&rcc 1166>;
+		dmas = <&dmamux1 0 39 0x400 0x01>,
+		       <&dmamux1 1 40 0x400 0x01>;
+		dma-names = "rx", "tx";
+		pinctrl-0 = <&spi2_pins_b>;
+		pinctrl-names = "default";
+		cs-gpios = <&gpioa 11 0>;
+
+		aardvark@0 {
+			compatible = "totalphase,aardvark";
+			reg = <0>;
+			spi-max-frequency = <4000000>;
+			st,spi-midi-ns = <4000>;
+		};
+	};

drivers/spi/Kconfig

@@ -627,6 +627,16 @@ config SPI_SIRF
 	help
 	  SPI driver for CSR SiRFprimaII SoCs
 
+config SPI_STM32
+	tristate "STMicroelectronics STM32 SPI controller"
+	depends on ARCH_STM32 || COMPILE_TEST
+	help
+	  SPI driver for STMicroelectonics STM32 SoCs.
+
+	  STM32 SPI controller supports DMA and PIO modes. When DMA
+	  is not available, the driver automatically falls back to
+	  PIO mode.
+
 config SPI_ST_SSC4
 	tristate "STMicroelectronics SPI SSC-based driver"
 	depends on ARCH_STI || COMPILE_TEST

drivers/spi/Makefile

@@ -90,6 +90,7 @@ obj-$(CONFIG_SPI_SH_HSPI)		+= spi-sh-hspi.o
 obj-$(CONFIG_SPI_SH_MSIOF)		+= spi-sh-msiof.o
 obj-$(CONFIG_SPI_SH_SCI)		+= spi-sh-sci.o
 obj-$(CONFIG_SPI_SIRF)		+= spi-sirf.o
+obj-$(CONFIG_SPI_STM32) 		+= spi-stm32.o
 obj-$(CONFIG_SPI_ST_SSC4)		+= spi-st-ssc4.o
 obj-$(CONFIG_SPI_SUN4I)			+= spi-sun4i.o
 obj-$(CONFIG_SPI_SUN6I)			+= spi-sun6i.o

drivers/spi/spi-st-ssc4.c

@@ -229,42 +229,42 @@ static int spi_st_setup(struct spi_device *spi)
 		"setting baudrate:target= %u hz, actual= %u hz, sscbrg= %u\n",
 		hz, spi_st->baud, sscbrg);
 
-	 /* Set SSC_CTL and enable SSC */
-	 var = readl_relaxed(spi_st->base + SSC_CTL);
-	 var |= SSC_CTL_MS;
+	/* Set SSC_CTL and enable SSC */
+	var = readl_relaxed(spi_st->base + SSC_CTL);
+	var |= SSC_CTL_MS;
 
-	 if (spi->mode & SPI_CPOL)
+	if (spi->mode & SPI_CPOL)
 		var |= SSC_CTL_PO;
-	 else
+	else
 		var &= ~SSC_CTL_PO;
 
-	 if (spi->mode & SPI_CPHA)
+	if (spi->mode & SPI_CPHA)
 		var |= SSC_CTL_PH;
-	 else
+	else
 		var &= ~SSC_CTL_PH;
 
-	 if ((spi->mode & SPI_LSB_FIRST) == 0)
+	if ((spi->mode & SPI_LSB_FIRST) == 0)
 		var |= SSC_CTL_HB;
-	 else
+	else
 		var &= ~SSC_CTL_HB;
 
-	 if (spi->mode & SPI_LOOP)
+	if (spi->mode & SPI_LOOP)
 		var |= SSC_CTL_LPB;
-	 else
+	else
 		var &= ~SSC_CTL_LPB;
 
-	 var &= ~SSC_CTL_DATA_WIDTH_MSK;
-	 var |= (spi->bits_per_word - 1);
+	var &= ~SSC_CTL_DATA_WIDTH_MSK;
+	var |= (spi->bits_per_word - 1);
 
-	 var |= SSC_CTL_EN_TX_FIFO | SSC_CTL_EN_RX_FIFO;
-	 var |= SSC_CTL_EN;
+	var |= SSC_CTL_EN_TX_FIFO | SSC_CTL_EN_RX_FIFO;
+	var |= SSC_CTL_EN;
 
-	 writel_relaxed(var, spi_st->base + SSC_CTL);
+	writel_relaxed(var, spi_st->base + SSC_CTL);
 
-	 /* Clear the status register */
-	 readl_relaxed(spi_st->base + SSC_RBUF);
+	/* Clear the status register */
+	readl_relaxed(spi_st->base + SSC_RBUF);
 
-	 return 0;
+	return 0;
 
 out_free_gpio:
 	gpio_free(cs);

drivers/spi/spidev.c

@@ -99,7 +99,6 @@ MODULE_PARM_DESC(bufsiz, "data bytes in biggest supported SPI message");
 static ssize_t
 spidev_sync(struct spidev_data *spidev, struct spi_message *message)
 {
-	DECLARE_COMPLETION_ONSTACK(done);
 	int status;
 	struct spi_device *spi;
 
@@ -325,7 +324,6 @@ static struct spi_ioc_transfer *
 spidev_get_ioc_message(unsigned int cmd, struct spi_ioc_transfer __user *u_ioc,
 		unsigned *n_ioc)
 {
-	struct spi_ioc_transfer	*ioc;
 	u32	tmp;
 
 	/* Check type, command number and direction */
@@ -342,14 +340,7 @@ spidev_get_ioc_message(unsigned int cmd, struct spi_ioc_transfer __user *u_ioc,
 		return NULL;
 
 	/* copy into scratch area */
-	ioc = kmalloc(tmp, GFP_KERNEL);
-	if (!ioc)
-		return ERR_PTR(-ENOMEM);
-	if (__copy_from_user(ioc, u_ioc, tmp)) {
-		kfree(ioc);
-		return ERR_PTR(-EFAULT);
-	}
-	return ioc;
+	return memdup_user(u_ioc, tmp);
 }
 
 static long