Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (25 commits) m68knommu: fix broken setting of irq_chip and handler m68knommu: switch to using -mcpu= flags for ColdFire targets m68knommu: arch/m68knommu/Kconfig whitespace cleanup m68knommu: create optimal separate instruction and data cache for ColdFire m68knommu: support ColdFire caches that do copyback and write-through m68knommu: support version 2 ColdFire split cache m68knommu: make cache push code ColdFire generic m68knommu: clean up ColdFire cache control code m68knommu: move inclusion of ColdFire v4 cache registers m68knommu: merge bit definitions for version 3 ColdFire cache controller m68knommu: create bit definitions for the version 2 ColdFire cache controller m68knommu: remove empty __iounmap() it is no used m68knommu: remove kernel_map() code, it is not used m68knommu: remove do_page_fault(), it is not used m68knommu: use user stack pointer hardware on some ColdFire cores m68knommu: remove command line printing DEBUG m68knommu: remove fasthandler interrupt code m68knommu: move UART addressing to part specific includes m68knommu: fix clock rate value reported for ColdFire 54xx parts m68knommu: move ColdFire CPU names into their headers ...
2024-12-16 14:02:10 +00:00 · 2011-01-18 08:05:20 -08:00 · 2011-01-18 08:05:20 -08:00 · 6a7f6ec951
commit 6a7f6ec951
parent c6fa63c659 4c65595ec5
38 changed files with 732 additions and 628 deletions
--- a/arch/m68k/include/asm/cacheflush_no.h
+++ b/arch/m68k/include/asm/cacheflush_no.h
@ -2,21 +2,22 @@
 #define _M68KNOMMU_CACHEFLUSH_H

 /*
- * (C) Copyright 2000-2004, Greg Ungerer <gerg@snapgear.com>
+ * (C) Copyright 2000-2010, Greg Ungerer <gerg@snapgear.com>
 */
 #include <linux/mm.h>
+#include <asm/mcfsim.h>

 #define flush_cache_all()			__flush_cache_all()
 #define flush_cache_mm(mm)			do { } while (0)
 #define flush_cache_dup_mm(mm)			do { } while (0)
-#define flush_cache_range(vma, start, end)	__flush_cache_all()
+#define flush_cache_range(vma, start, end)	do { } while (0)
 #define flush_cache_page(vma, vmaddr)		do { } while (0)
-#define flush_dcache_range(start,len)		__flush_cache_all()
+#define flush_dcache_range(start, len)		__flush_dcache_all()
 #define ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE 0
 #define flush_dcache_page(page)			do { } while (0)
 #define flush_dcache_mmap_lock(mapping)		do { } while (0)
 #define flush_dcache_mmap_unlock(mapping)	do { } while (0)
-#define flush_icache_range(start,len)		__flush_cache_all()
+#define flush_icache_range(start, len)		__flush_icache_all()
 #define flush_icache_page(vma,pg)		do { } while (0)
 #define flush_icache_user_range(vma,pg,adr,len)	do { } while (0)
 #define flush_cache_vmap(start, end)		do { } while (0)
@ -27,66 +28,52 @@
 #define copy_from_user_page(vma, page, vaddr, dst, src, len) \
 	memcpy(dst, src, len)

+void mcf_cache_push(void);
+
 static inline void __flush_cache_all(void)
 {
-#if defined(CONFIG_M5407) || defined(CONFIG_M548x)
-	/*
-	 *	Use cpushl to push and invalidate all cache lines.
-	 *	Gas doesn't seem to know how to generate the ColdFire
-	 *	cpushl instruction... Oh well, bit stuff it for now.
-	 */
+#ifdef CACHE_PUSH
+	mcf_cache_push();
+#endif
+#ifdef CACHE_INVALIDATE
 	__asm__ __volatile__ (
-		"nop\n\t"
-		"clrl	%%d0\n\t"
-		"1:\n\t"
-		"movel	%%d0,%%a0\n\t"
-		"2:\n\t"
-		".word	0xf468\n\t"
-		"addl	#0x10,%%a0\n\t"
-		"cmpl	#0x00000800,%%a0\n\t"
-		"blt	2b\n\t"
-		"addql	#1,%%d0\n\t"
-		"cmpil	#4,%%d0\n\t"
-		"bne	1b\n\t"
-		"movel	#0xb6088500,%%d0\n\t"
-		"movec	%%d0,%%CACR\n\t"
-		: : : "d0", "a0" );
-#endif /* CONFIG_M5407 */
-#if defined(CONFIG_M523x) || defined(CONFIG_M527x)
-	__asm__ __volatile__ (
-		"movel	#0x81400100, %%d0\n\t"
+		"movel	%0, %%d0\n\t"
 		"movec	%%d0, %%CACR\n\t"
 		"nop\n\t"
-		: : : "d0" );
-#endif /* CONFIG_M523x || CONFIG_M527x */
-#if defined(CONFIG_M528x)
-	__asm__ __volatile__ (
-		"movel	#0x81000200, %%d0\n\t"
-		"movec	%%d0, %%CACR\n\t"
-		"nop\n\t"
-		: : : "d0" );
-#endif /* CONFIG_M528x */
-#if defined(CONFIG_M5206) || defined(CONFIG_M5206e) || defined(CONFIG_M5272)
-	__asm__ __volatile__ (
-		"movel	#0x81000100, %%d0\n\t"
-		"movec	%%d0, %%CACR\n\t"
-		"nop\n\t"
-		: : : "d0" );
-#endif /* CONFIG_M5206 || CONFIG_M5206e || CONFIG_M5272 */
-#ifdef CONFIG_M5249
-	__asm__ __volatile__ (
-		"movel	#0xa1000200, %%d0\n\t"
-		"movec	%%d0, %%CACR\n\t"
-		"nop\n\t"
-		: : : "d0" );
-#endif /* CONFIG_M5249 */
-#ifdef CONFIG_M532x
-	__asm__ __volatile__ (
-		"movel	#0x81000200, %%d0\n\t"
-		"movec	%%d0, %%CACR\n\t"
-		"nop\n\t"
-		: : : "d0" );
-#endif /* CONFIG_M532x */
+		: : "i" (CACHE_INVALIDATE) : "d0" );
+#endif
 }

+/*
+ * Some ColdFire parts implement separate instruction and data caches,
+ * on those we should just flush the appropriate cache. If we don't need
+ * to do any specific flushing then this will be optimized away.
+ */
+static inline void __flush_icache_all(void)
+{
+#ifdef CACHE_INVALIDATEI
+	__asm__ __volatile__ (
+		"movel	%0, %%d0\n\t"
+		"movec	%%d0, %%CACR\n\t"
+		"nop\n\t"
+		: : "i" (CACHE_INVALIDATEI) : "d0" );
+#endif
+}
+
+static inline void __flush_dcache_all(void)
+{
+#ifdef CACHE_PUSH
+	mcf_cache_push();
+#endif
+#ifdef CACHE_INVALIDATED
+	__asm__ __volatile__ (
+		"movel	%0, %%d0\n\t"
+		"movec	%%d0, %%CACR\n\t"
+		"nop\n\t"
+		: : "i" (CACHE_INVALIDATED) : "d0" );
+#else
+	/* Flush the wrtite buffer */
+	__asm__ __volatile__ ( "nop" );
+#endif
+}
 #endif /* _M68KNOMMU_CACHEFLUSH_H */
--- a/arch/m68k/include/asm/coldfire.h
+++ b/arch/m68k/include/asm/coldfire.h
@ -32,7 +32,7 @@
 */
 #define	MCF_MBAR	0x10000000
 #define	MCF_MBAR2	0x80000000
-#if defined(CONFIG_M548x)
+#if defined(CONFIG_M54xx)
 #define	MCF_IPSBAR	MCF_MBAR
 #elif defined(CONFIG_M520x)
 #define	MCF_IPSBAR	0xFC000000
--- a/arch/m68k/include/asm/entry_no.h
+++ b/arch/m68k/include/asm/entry_no.h
@ -42,12 +42,16 @@
 */

 #ifdef CONFIG_COLDFIRE
+#ifdef CONFIG_COLDFIRE_SW_A7
 /*
- * This is made a little more tricky on the ColdFire. There is no
- * separate kernel and user stack pointers. Need to artificially
+ * This is made a little more tricky on older ColdFires. There is no
+ * separate supervisor and user stack pointers. Need to artificially
 * construct a usp in software... When doing this we need to disable
- * interrupts, otherwise bad things could happen.
+ * interrupts, otherwise bad things will happen.
 */
+.globl sw_usp
+.globl sw_ksp
+
 .macro SAVE_ALL
 	move	#0x2700,%sr		/* disable intrs */
 	btst	#5,%sp@(2)		/* from user? */
@ -74,9 +78,7 @@
 	7:
 .endm

-.macro RESTORE_ALL
-	btst	#5,%sp@(PT_SR)		/* going user? */
-	bnes	8f			/* no, skip */
+.macro RESTORE_USER
 	move	#0x2700,%sr		/* disable intrs */
 	movel	sw_usp,%a0		/* get usp */
 	movel	%sp@(PT_OFF_PC),%a0@-	/* copy exception program counter */
@ -91,19 +93,22 @@
 	subql	#8,sw_usp		/* set exception */
 	movel	sw_usp,%sp		/* restore usp */
 	rte
-	8:
-	moveml	%sp@,%d1-%d5/%a0-%a2
-	lea	%sp@(32),%sp		/* space for 8 regs */
-	movel	%sp@+,%d0
-	addql	#4,%sp			/* orig d0 */
-	addl	%sp@+,%sp		/* stkadj */
-	rte
 .endm

+.macro RDUSP
+	movel	sw_usp,%a2
+.endm
+
+.macro WRUSP
+	movel	%a0,sw_usp
+.endm
+
+#else /* !CONFIG_COLDFIRE_SW_A7 */
 /*
- * Quick exception save, use current stack only.
+ * Modern ColdFire parts have separate supervisor and user stack
+ * pointers. Simple load and restore macros for this case.
 */
-.macro SAVE_LOCAL
+.macro SAVE_ALL
 	move	#0x2700,%sr		/* disable intrs */
 	clrl	%sp@-			/* stkadj */
 	movel	%d0,%sp@-		/* orig d0 */
@ -112,7 +117,7 @@
 	moveml	%d1-%d5/%a0-%a2,%sp@
 .endm

-.macro RESTORE_LOCAL
+.macro RESTORE_USER
 	moveml	%sp@,%d1-%d5/%a0-%a2
 	lea	%sp@(32),%sp		/* space for 8 regs */
 	movel	%sp@+,%d0
@ -121,6 +126,18 @@
 	rte
 .endm

+.macro RDUSP
+	/*move	%usp,%a2*/
+	.word	0x4e6a
+.endm
+
+.macro WRUSP
+	/*move	%a0,%usp*/
+	.word	0x4e60
+.endm
+
+#endif /* !CONFIG_COLDFIRE_SW_A7 */
+
 .macro SAVE_SWITCH_STACK
 	lea	%sp@(-24),%sp		/* 6 regs */
 	moveml	%a3-%a6/%d6-%d7,%sp@
@ -131,14 +148,6 @@
 	lea	%sp@(24),%sp		/* 6 regs */
 .endm

-/*
- * Software copy of the user and kernel stack pointers... Ugh...
- * Need these to get around ColdFire not having separate kernel
- * and user stack pointers.
- */
-.globl sw_usp
-.globl sw_ksp
-
 #else /* !CONFIG_COLDFIRE */

 /*
@ -167,6 +176,6 @@
 	moveml	%sp@+,%a3-%a6/%d6-%d7
 .endm

-#endif /* !CONFIG_COLDFIRE */
+#endif /* !COLDFIRE_SW_A7 */
 #endif /* __ASSEMBLY__ */
 #endif /* __M68KNOMMU_ENTRY_H */
--- a/arch/m68k/include/asm/gpio.h
+++ b/arch/m68k/include/asm/gpio.h
@ -37,7 +37,7 @@
 #if defined(CONFIG_M5206) || defined(CONFIG_M5206e) || \
    defined(CONFIG_M520x) || defined(CONFIG_M523x) || \
    defined(CONFIG_M527x) || defined(CONFIG_M528x) || \
-    defined(CONFIG_M532x) || defined(CONFIG_M548x)
+    defined(CONFIG_M532x) || defined(CONFIG_M54xx)

 /* These parts have GPIO organized by 8 bit ports */

--- a/arch/m68k/include/asm/io_no.h
+++ b/arch/m68k/include/asm/io_no.h
@ -145,7 +145,6 @@ static inline void io_insl(unsigned int addr, void *buf, int len)
 #define IOMAP_WRITETHROUGH		3

 extern void *__ioremap(unsigned long physaddr, unsigned long size, int cacheflag);
-extern void __iounmap(void *addr, unsigned long size);

 static inline void *ioremap(unsigned long physaddr, unsigned long size)
 {
--- a/arch/m68k/include/asm/m5206sim.h
+++ b/arch/m68k/include/asm/m5206sim.h
@ -12,6 +12,10 @@
 #define	m5206sim_h
 /****************************************************************************/

+#define	CPU_NAME		"COLDFIRE(m5206)"
+#define	CPU_INSTR_PER_JIFFY	3
+
+#include <asm/m52xxacr.h>

 /*
 *	Define the 5206 SIM register set addresses.
@ -88,6 +92,14 @@
 #define	MCFSIM_PADDR		(MCF_MBAR + 0x1c5)	/* Parallel Direction (r/w) */
 #define	MCFSIM_PADAT		(MCF_MBAR + 0x1c9)	/* Parallel Port Value (r/w) */

+#if defined(CONFIG_NETtel)
+#define	MCFUART_BASE1		0x180		/* Base address of UART1 */
+#define	MCFUART_BASE2		0x140		/* Base address of UART2 */
+#else
+#define	MCFUART_BASE1		0x140		/* Base address of UART1 */
+#define	MCFUART_BASE2		0x180		/* Base address of UART2 */
+#endif
+
 /*
 *	Define system peripheral IRQ usage.
 */
--- a/arch/m68k/include/asm/m520xsim.h
+++ b/arch/m68k/include/asm/m520xsim.h
@ -11,6 +11,11 @@
 #define m520xsim_h
 /****************************************************************************/

+#define	CPU_NAME		"COLDFIRE(m520x)"
+#define	CPU_INSTR_PER_JIFFY	3
+
+#include <asm/m52xxacr.h>
+
 /*
 *  Define the 520x SIM register set addresses.
 */
@ -54,6 +59,9 @@
 #define MCFSIM_SDCS0        0x000a8110	/* SDRAM Chip Select 0 Configuration */
 #define MCFSIM_SDCS1        0x000a8114	/* SDRAM Chip Select 1 Configuration */

+/*
+ * EPORT and GPIO registers.
+ */
 #define MCFEPORT_EPDDR			0xFC088002
 #define MCFEPORT_EPDR			0xFC088004
 #define MCFEPORT_EPPDR			0xFC088005
@ -97,6 +105,7 @@
 #define MCFGPIO_PCLRR_UART		0xFC0A402A
 #define MCFGPIO_PCLRR_FECH		0xFC0A402B
 #define MCFGPIO_PCLRR_FECL		0xFC0A402C
+
 /*
 * Generic GPIO support
 */
@ -109,7 +118,6 @@
 #define MCFGPIO_PIN_MAX			80
 #define MCFGPIO_IRQ_MAX			8
 #define MCFGPIO_IRQ_VECBASE		MCFINT_VECBASE
-/****************************************************************************/

 #define MCF_GPIO_PAR_UART                   (0xA4036)
 #define MCF_GPIO_PAR_FECI2C                 (0xA4033)
@ -125,6 +133,13 @@
 #define MCF_GPIO_PAR_FECI2C_PAR_SDA_URXD2   (0x02)
 #define MCF_GPIO_PAR_FECI2C_PAR_SCL_UTXD2   (0x04)

+/*
+ *  UART module.
+ */
+#define MCFUART_BASE1		0x60000		/* Base address of UART1 */
+#define MCFUART_BASE2		0x64000		/* Base address of UART2 */
+#define MCFUART_BASE3		0x68000		/* Base address of UART2 */
+
 /*
 *  Reset Controll Unit.
 */
--- a/arch/m68k/include/asm/m523xsim.h
+++ b/arch/m68k/include/asm/m523xsim.h
@ -11,6 +11,10 @@
 #define	m523xsim_h
 /****************************************************************************/

+#define	CPU_NAME		"COLDFIRE(m523x)"
+#define	CPU_INSTR_PER_JIFFY	3
+
+#include <asm/m52xxacr.h>

 /*
 *	Define the 523x SIM register set addresses.
@ -50,6 +54,13 @@
 #define	MCF_RCR_SWRESET		0x80		/* Software reset bit */
 #define	MCF_RCR_FRCSTOUT	0x40		/* Force external reset */

+/*
+ *  UART module.
+ */
+#define MCFUART_BASE1		0x200           /* Base address of UART1 */
+#define MCFUART_BASE2		0x240           /* Base address of UART2 */
+#define MCFUART_BASE3		0x280           /* Base address of UART3 */
+
 #define MCFGPIO_PODR_ADDR	(MCF_IPSBAR + 0x100000)
 #define MCFGPIO_PODR_DATAH	(MCF_IPSBAR + 0x100001)
 #define MCFGPIO_PODR_DATAL	(MCF_IPSBAR + 0x100002)
--- a/arch/m68k/include/asm/m5249sim.h
+++ b/arch/m68k/include/asm/m5249sim.h
@ -11,6 +11,11 @@
 #define	m5249sim_h
 /****************************************************************************/

+#define	CPU_NAME		"COLDFIRE(m5249)"
+#define	CPU_INSTR_PER_JIFFY	3
+
+#include <asm/m52xxacr.h>
+
 /*
 *	Define the 5249 SIM register set addresses.
 */
@ -56,6 +61,11 @@
 #define MCFSIM_DACR1		0x110		/* DRAM 1 Addr and Ctrl (r/w) */
 #define MCFSIM_DMR1		0x114		/* DRAM 1 Mask reg (r/w) */

+/*
+ *	UART module.
+ */
+#define MCFUART_BASE1		0x1c0           /* Base address of UART1 */
+#define MCFUART_BASE2		0x200           /* Base address of UART2 */

 /*
 *	Some symbol defines for the above...
--- a/arch/m68k/include/asm/m5272sim.h
+++ b/arch/m68k/include/asm/m5272sim.h
@ -12,6 +12,11 @@
 #define	m5272sim_h
 /****************************************************************************/

+#define	CPU_NAME		"COLDFIRE(m5272)"
+#define	CPU_INSTR_PER_JIFFY	3
+
+#include <asm/m52xxacr.h>
+
 /*
 *	Define the 5272 SIM register set addresses.
 */
@ -62,6 +67,9 @@
 #define	MCFSIM_DCMR1		0x5c		/* DRAM 1 Mask reg (r/w) */
 #define	MCFSIM_DCCR1		0x63		/* DRAM 1 Control reg (r/w) */

+#define	MCFUART_BASE1		0x100		/* Base address of UART1 */
+#define	MCFUART_BASE2		0x140		/* Base address of UART2 */
+
 #define	MCFSIM_PACNT		(MCF_MBAR + 0x80) /* Port A Control (r/w) */
 #define	MCFSIM_PADDR		(MCF_MBAR + 0x84) /* Port A Direction (r/w) */
 #define	MCFSIM_PADAT		(MCF_MBAR + 0x86) /* Port A Data (r/w) */
--- a/arch/m68k/include/asm/m527xsim.h
+++ b/arch/m68k/include/asm/m527xsim.h
@ -11,6 +11,10 @@
 #define	m527xsim_h
 /****************************************************************************/

+#define	CPU_NAME		"COLDFIRE(m527x)"
+#define	CPU_INSTR_PER_JIFFY	3
+
+#include <asm/m52xxacr.h>

 /*
 *	Define the 5270/5271 SIM register set addresses.
@ -55,6 +59,12 @@
 #define	MCFSIM_DMR1		0x5c		/* SDRAM address mask 1 */
 #endif

+/*
+ *	UART module.
+ */
+#define MCFUART_BASE1		0x200           /* Base address of UART1 */
+#define MCFUART_BASE2		0x240           /* Base address of UART2 */
+#define MCFUART_BASE3		0x280           /* Base address of UART3 */

 #ifdef CONFIG_M5271
 #define MCFGPIO_PODR_ADDR	(MCF_IPSBAR + 0x100000)
--- a/arch/m68k/include/asm/m528xsim.h
+++ b/arch/m68k/include/asm/m528xsim.h
@ -11,6 +11,10 @@
 #define	m528xsim_h
 /****************************************************************************/

+#define	CPU_NAME		"COLDFIRE(m528x)"
+#define	CPU_INSTR_PER_JIFFY	3
+
+#include <asm/m52xxacr.h>

 /*
 *	Define the 5280/5282 SIM register set addresses.
@ -41,6 +45,13 @@
 #define	MCFSIM_DACR1		0x50		/* SDRAM base address 1 */
 #define	MCFSIM_DMR1		0x54		/* SDRAM address mask 1 */

+/*
+ *	UART module.
+ */
+#define MCFUART_BASE1		0x200           /* Base address of UART1 */
+#define MCFUART_BASE2		0x240           /* Base address of UART2 */
+#define MCFUART_BASE3		0x280           /* Base address of UART3 */
+
 /*
 * 	GPIO registers
 */
--- a/arch/m68k/include/asm/m52xxacr.h
+++ b/arch/m68k/include/asm/m52xxacr.h
@ -0,0 +1,94 @@
+/****************************************************************************/
+
+/*
+ * m52xxacr.h -- ColdFire version 2 core cache support
+ *
+ * (C) Copyright 2010, Greg Ungerer <gerg@snapgear.com>
+ */
+
+/****************************************************************************/
+#ifndef m52xxacr_h
+#define m52xxacr_h
+/****************************************************************************/
+
+/*
+ * All varients of the ColdFire using version 2 cores have a similar
+ * cache setup. Although not absolutely identical the cache register
+ * definitions are compatible for all of them. Mostly they support a
+ * configurable cache memory that can be instruction only, data only,
+ * or split instruction and data. The exception is the very old version 2
+ * core based parts, like the 5206(e), 5249 and 5272, which are instruction
+ * cache only. Cache size varies from 2k up to 16k.
+ */
+
+/*
+ * Define the Cache Control register flags.
+ */
+#define CACR_CENB	0x80000000	/* Enable cache */
+#define CACR_CDPI	0x10000000	/* Disable invalidation by CPUSHL */
+#define CACR_CFRZ	0x08000000	/* Cache freeze mode */
+#define CACR_CINV	0x01000000	/* Invalidate cache */
+#define CACR_DISI	0x00800000	/* Disable instruction cache */
+#define CACR_DISD	0x00400000	/* Disable data cache */
+#define CACR_INVI	0x00200000	/* Invalidate instruction cache */
+#define CACR_INVD	0x00100000	/* Invalidate data cache */
+#define CACR_CEIB	0x00000400	/* Non-cachable instruction burst */
+#define CACR_DCM	0x00000200	/* Default cache mode */
+#define CACR_DBWE	0x00000100	/* Buffered write enable */
+#define CACR_DWP	0x00000020	/* Write protection */
+#define CACR_EUSP	0x00000010	/* Enable separate user a7 */
+
+/*
+ * Define the Access Control register flags.
+ */
+#define ACR_BASE_POS	24		/* Address Base (upper 8 bits) */
+#define ACR_MASK_POS	16		/* Address Mask (next 8 bits) */
+#define ACR_ENABLE	0x00008000	/* Enable this ACR */
+#define ACR_USER	0x00000000	/* Allow only user accesses */
+#define ACR_SUPER	0x00002000	/* Allow supervisor access only */
+#define ACR_ANY		0x00004000	/* Allow any access type */
+#define ACR_CENB	0x00000000	/* Caching of region enabled */
+#define ACR_CDIS	0x00000040	/* Caching of region disabled */
+#define ACR_BWE		0x00000020	/* Write buffer enabled */
+#define ACR_WPROTECT	0x00000004	/* Write protect region */
+
+/*
+ * Set the cache controller settings we will use. On the cores that support
+ * a split cache configuration we allow all the combinations at Kconfig
+ * time. For those cores that only have an instruction cache we just set
+ * that as on.
+ */
+#if defined(CONFIG_CACHE_I)
+#define CACHE_TYPE	(CACR_DISD + CACR_EUSP)
+#define CACHE_INVTYPEI	0
+#elif defined(CONFIG_CACHE_D)
+#define CACHE_TYPE	(CACR_DISI + CACR_EUSP)
+#define CACHE_INVTYPED	0
+#elif defined(CONFIG_CACHE_BOTH)
+#define CACHE_TYPE	CACR_EUSP
+#define CACHE_INVTYPEI	CACR_INVI
+#define CACHE_INVTYPED	CACR_INVD
+#else
+/* This is the instruction cache only devices (no split cache, no eusp) */
+#define CACHE_TYPE	0
+#define CACHE_INVTYPEI	0
+#endif
+
+#define CACHE_INIT	(CACR_CINV + CACHE_TYPE)
+#define CACHE_MODE	(CACR_CENB + CACHE_TYPE + CACR_DCM)
+
+#define CACHE_INVALIDATE  (CACHE_MODE + CACR_CINV)
+#if defined(CACHE_INVTYPEI)
+#define CACHE_INVALIDATEI (CACHE_MODE + CACR_CINV + CACHE_INVTYPEI)
+#endif
+#if defined(CACHE_INVTYPED)
+#define CACHE_INVALIDATED (CACHE_MODE + CACR_CINV + CACHE_INVTYPED)
+#endif
+
+#define ACR0_MODE	((CONFIG_RAMBASE & 0xff000000) + \
+			 (0x000f0000) + \
+			 (ACR_ENABLE + ACR_ANY + ACR_CENB + ACR_BWE))
+#define ACR1_MODE	0
+
+/****************************************************************************/
+#endif  /* m52xxsim_h */
--- a/arch/m68k/include/asm/m5307sim.h
+++ b/arch/m68k/include/asm/m5307sim.h
@ -14,6 +14,11 @@
 #define	m5307sim_h
 /****************************************************************************/

+#define	CPU_NAME		"COLDFIRE(m5307)"
+#define	CPU_INSTR_PER_JIFFY	3
+
+#include <asm/m53xxacr.h>
+
 /*
 *	Define the 5307 SIM register set addresses.
 */
@ -93,6 +98,17 @@
 #define	MCFSIM_PADDR		(MCF_MBAR + 0x244)
 #define	MCFSIM_PADAT		(MCF_MBAR + 0x248)

+/*
+ *  UART module.
+ */
+#if defined(CONFIG_NETtel) || defined(CONFIG_SECUREEDGEMP3)
+#define MCFUART_BASE1		0x200           /* Base address of UART1 */
+#define MCFUART_BASE2		0x1c0           /* Base address of UART2 */
+#else
+#define MCFUART_BASE1		0x1c0           /* Base address of UART1 */
+#define MCFUART_BASE2		0x200           /* Base address of UART2 */
+#endif
+
 /*
 * Generic GPIO support
 */
@ -146,32 +162,5 @@
 #define	MCF_IRQ_TIMER		30		/* Timer0, Level 6 */
 #define	MCF_IRQ_PROFILER	31		/* Timer1, Level 7 */

-/*
- *	Define the Cache register flags.
- */
-#define	CACR_EC			(1<<31)
-#define	CACR_ESB		(1<<29)
-#define	CACR_DPI		(1<<28)
-#define	CACR_HLCK		(1<<27)
-#define	CACR_CINVA		(1<<24)
-#define	CACR_DNFB		(1<<10)
-#define	CACR_DCM_WTHRU		(0<<8)
-#define	CACR_DCM_WBACK		(1<<8)
-#define	CACR_DCM_OFF_PRE	(2<<8)
-#define	CACR_DCM_OFF_IMP	(3<<8)
-#define	CACR_DW			(1<<5)
-
-#define	ACR_BASE_POS		24
-#define	ACR_MASK_POS		16
-#define	ACR_ENABLE		(1<<15)
-#define	ACR_USER		(0<<13)
-#define	ACR_SUPER		(1<<13)
-#define	ACR_ANY			(2<<13)
-#define	ACR_CM_WTHRU		(0<<5)
-#define	ACR_CM_WBACK		(1<<5)
-#define	ACR_CM_OFF_PRE		(2<<5)
-#define	ACR_CM_OFF_IMP		(3<<5)
-#define	ACR_WPROTECT		(1<<2)
-
 /****************************************************************************/
 #endif	/* m5307sim_h */
--- a/arch/m68k/include/asm/m532xsim.h
+++ b/arch/m68k/include/asm/m532xsim.h
@ -9,6 +9,11 @@
 #define	m532xsim_h
 /****************************************************************************/

+#define	CPU_NAME		"COLDFIRE(m532x)"
+#define	CPU_INSTR_PER_JIFFY	3
+
+#include <asm/m53xxacr.h>
+
 #define MCF_REG32(x) (*(volatile unsigned long  *)(x))
 #define MCF_REG16(x) (*(volatile unsigned short *)(x))
 #define MCF_REG08(x) (*(volatile unsigned char  *)(x))
@ -74,31 +79,11 @@
 #define	MCF_IRQ_PROFILER	(64 + 33)	/* Timer1 */

 /*
- *	Define the Cache register flags.
+ *  UART module.
 */
-#define	CACR_EC			(1<<31)
-#define	CACR_ESB		(1<<29)
-#define	CACR_DPI		(1<<28)
-#define	CACR_HLCK		(1<<27)
-#define	CACR_CINVA		(1<<24)
-#define	CACR_DNFB		(1<<10)
-#define	CACR_DCM_WTHRU		(0<<8)
-#define	CACR_DCM_WBACK		(1<<8)
-#define	CACR_DCM_OFF_PRE	(2<<8)
-#define	CACR_DCM_OFF_IMP	(3<<8)
-#define	CACR_DW			(1<<5)
-
-#define	ACR_BASE_POS		24
-#define	ACR_MASK_POS		16
-#define	ACR_ENABLE		(1<<15)
-#define	ACR_USER		(0<<13)
-#define	ACR_SUPER		(1<<13)
-#define	ACR_ANY			(2<<13)
-#define	ACR_CM_WTHRU		(0<<5)
-#define	ACR_CM_WBACK		(1<<5)
-#define	ACR_CM_OFF_PRE		(2<<5)
-#define	ACR_CM_OFF_IMP		(3<<5)
-#define	ACR_WPROTECT		(1<<2)
+#define MCFUART_BASE1		0xFC060000	/* Base address of UART1 */
+#define MCFUART_BASE2		0xFC064000	/* Base address of UART2 */
+#define MCFUART_BASE3		0xFC068000	/* Base address of UART3 */

 /*********************************************************************
 *
--- a/arch/m68k/include/asm/m53xxacr.h
+++ b/arch/m68k/include/asm/m53xxacr.h
@ -0,0 +1,101 @@
+/****************************************************************************/
+
+/*
+ * m53xxacr.h -- ColdFire version 3 core cache support
+ *
+ * (C) Copyright 2010, Greg Ungerer <gerg@snapgear.com>
+ */
+
+/****************************************************************************/
+#ifndef m53xxacr_h
+#define m53xxacr_h
+/****************************************************************************/
+
+/*
+ * All varients of the ColdFire using version 3 cores have a similar
+ * cache setup. They have a unified instruction and data cache, with
+ * configurable write-through or copy-back operation.
+ */
+
+/*
+ * Define the Cache Control register flags.
+ */
+#define CACR_EC		0x80000000	/* Enable cache */
+#define CACR_ESB	0x20000000	/* Enable store buffer */
+#define CACR_DPI	0x10000000	/* Disable invalidation by CPUSHL */
+#define CACR_HLCK	0x08000000	/* Half cache lock mode */
+#define CACR_CINVA	0x01000000	/* Invalidate cache */
+#define CACR_DNFB	0x00000400	/* Inhibited fill buffer */
+#define CACR_DCM_WT	0x00000000	/* Cacheable write-through */
+#define CACR_DCM_CB	0x00000100	/* Cacheable copy-back */
+#define CACR_DCM_PRE	0x00000200	/* Cache inhibited, precise */
+#define CACR_DCM_IMPRE	0x00000300	/* Cache inhibited, imprecise */
+#define CACR_WPROTECT	0x00000020	/* Write protect*/
+#define CACR_EUSP	0x00000010	/* Eanble separate user a7 */
+
+/*
+ * Define the Access Control register flags.
+ */
+#define ACR_BASE_POS	24		/* Address Base (upper 8 bits) */
+#define ACR_MASK_POS	16		/* Address Mask (next 8 bits) */
+#define ACR_ENABLE	0x00008000	/* Enable this ACR */
+#define ACR_USER	0x00000000	/* Allow only user accesses */
+#define ACR_SUPER	0x00002000	/* Allow supervisor access only */
+#define ACR_ANY		0x00004000	/* Allow any access type */
+#define ACR_CM_WT	0x00000000	/* Cacheable, write-through */
+#define ACR_CM_CB	0x00000020	/* Cacheable, copy-back */
+#define ACR_CM_PRE	0x00000040	/* Cache inhibited, precise */
+#define ACR_CM_IMPRE	0x00000060	/* Cache inhibited, imprecise */
+#define ACR_WPROTECT	0x00000004	/* Write protect region */
+
+/*
+ * Define the cache type and arrangement (needed for pushes).
+ */
+#if defined(CONFIG_M5307)
+#define	CACHE_SIZE	0x2000		/* 8k of unified cache */
+#define	ICACHE_SIZE	CACHE_SIZE
+#define	DCACHE_SIZE	CACHE_SIZE
+#elif defined(CONFIG_M532x)
+#define	CACHE_SIZE	0x4000		/* 32k of unified cache */
+#define	ICACHE_SIZE	CACHE_SIZE
+#define	DCACHE_SIZE	CACHE_SIZE
+#endif
+
+#define	CACHE_LINE_SIZE	16		/* 16 byte line size */
+#define	CACHE_WAYS	4		/* 4 ways - set associative */
+
+/*
+ * Set the cache controller settings we will use. This default in the
+ * CACR is cache inhibited, we use the ACR register to set cacheing
+ * enabled on the regions we want (eg RAM).
+ */
+#if defined(CONFIG_CACHE_COPYBACK)
+#define CACHE_TYPE	ACR_CM_CB
+#define CACHE_PUSH
+#else
+#define CACHE_TYPE	ACR_CM_WT
+#endif
+
+#ifdef CONFIG_COLDFIRE_SW_A7
+#define CACHE_MODE	(CACR_EC + CACR_ESB + CACR_DCM_PRE)
+#else
+#define CACHE_MODE	(CACR_EC + CACR_ESB + CACR_DCM_PRE + CACR_EUSP)
+#endif
+
+/*
+ * Unified cache means we will never need to flush for coherency of
+ * instruction fetch. We will need to flush to maintain memory/DMA
+ * coherency though in all cases. And for copyback caches we will need
+ * to push cached data as well.
+ */
+#define CACHE_INIT	  CACR_CINVA
+#define CACHE_INVALIDATE  CACR_CINVA
+#define CACHE_INVALIDATED CACR_CINVA
+
+#define ACR0_MODE	((CONFIG_RAMBASE & 0xff000000) + \
+			 (0x000f0000) + \
+			 (ACR_ENABLE + ACR_ANY + CACHE_TYPE))
+#define ACR1_MODE	0
+
+/****************************************************************************/
+#endif  /* m53xxsim_h */
--- a/arch/m68k/include/asm/m5407sim.h
+++ b/arch/m68k/include/asm/m5407sim.h
@ -14,6 +14,11 @@
 #define	m5407sim_h
 /****************************************************************************/

+#define	CPU_NAME		"COLDFIRE(m5407)"
+#define	CPU_INSTR_PER_JIFFY	3
+
+#include <asm/m54xxacr.h>
+
 /*
 *	Define the 5407 SIM register set addresses.
 */
@ -73,6 +78,9 @@
 #define MCFSIM_DACR1		0x110		/* DRAM 1 Addr and Ctrl (r/w) */
 #define MCFSIM_DMR1		0x114		/* DRAM 1 Mask reg (r/w) */

+#define MCFUART_BASE1		0x1c0           /* Base address of UART1 */
+#define MCFUART_BASE2		0x200           /* Base address of UART2 */
+
 #define	MCFSIM_PADDR		(MCF_MBAR + 0x244)
 #define	MCFSIM_PADAT		(MCF_MBAR + 0x248)

@ -117,39 +125,5 @@
 #define	MCF_IRQ_TIMER		30		/* Timer0, Level 6 */
 #define	MCF_IRQ_PROFILER	31		/* Timer1, Level 7 */

-/*
- *	Define the Cache register flags.
- */
-#define	CACR_DEC		0x80000000	/* Enable data cache */
-#define	CACR_DWP		0x40000000	/* Data write protection */
-#define	CACR_DESB		0x20000000	/* Enable data store buffer */
-#define	CACR_DDPI		0x10000000	/* Disable CPUSHL */
-#define	CACR_DHCLK		0x08000000	/* Half data cache lock mode */
-#define	CACR_DDCM_WT		0x00000000	/* Write through cache*/
-#define	CACR_DDCM_CP		0x02000000	/* Copyback cache */
-#define	CACR_DDCM_P		0x04000000	/* No cache, precise */
-#define	CACR_DDCM_IMP		0x06000000	/* No cache, imprecise */
-#define	CACR_DCINVA		0x01000000	/* Invalidate data cache */
-#define	CACR_BEC		0x00080000	/* Enable branch cache */
-#define	CACR_BCINVA		0x00040000	/* Invalidate branch cache */
-#define	CACR_IEC		0x00008000	/* Enable instruction cache */
-#define	CACR_DNFB		0x00002000	/* Inhibited fill buffer */
-#define	CACR_IDPI		0x00001000	/* Disable CPUSHL */
-#define	CACR_IHLCK		0x00000800	/* Intruction cache half lock */
-#define	CACR_IDCM		0x00000400	/* Intruction cache inhibit */
-#define	CACR_ICINVA		0x00000100	/* Invalidate instr cache */
-
-#define	ACR_BASE_POS		24		/* Address Base */
-#define	ACR_MASK_POS		16		/* Address Mask */
-#define	ACR_ENABLE		0x00008000	/* Enable address */
-#define	ACR_USER		0x00000000	/* User mode access only */
-#define	ACR_SUPER		0x00002000	/* Supervisor mode only */
-#define	ACR_ANY			0x00004000	/* Match any access mode */
-#define	ACR_CM_WT		0x00000000	/* Write through mode */
-#define	ACR_CM_CP		0x00000020	/* Copyback mode */
-#define	ACR_CM_OFF_PRE		0x00000040	/* No cache, precise */
-#define	ACR_CM_OFF_IMP		0x00000060	/* No cache, imprecise */
-#define	ACR_WPROTECT		0x00000004	/* Write protect */
-
 /****************************************************************************/
 #endif	/* m5407sim_h */
--- a/arch/m68k/include/asm/m54xxacr.h
+++ b/arch/m68k/include/asm/m54xxacr.h
@ -0,0 +1,97 @@
+/*
+ * Bit definitions for the MCF54xx ACR and CACR registers.
+ */
+
+#ifndef	m54xxacr_h
+#define m54xxacr_h
+
+/*
+ *	Define the Cache register flags.
+ */
+#define CACR_DEC	0x80000000	/* Enable data cache */
+#define CACR_DWP	0x40000000	/* Data write protection */
+#define CACR_DESB	0x20000000	/* Enable data store buffer */
+#define CACR_DDPI	0x10000000	/* Disable invalidation by CPUSHL */
+#define CACR_DHCLK	0x08000000	/* Half data cache lock mode */
+#define CACR_DDCM_WT	0x00000000	/* Write through cache*/
+#define CACR_DDCM_CP	0x02000000	/* Copyback cache */
+#define CACR_DDCM_P	0x04000000	/* No cache, precise */
+#define CACR_DDCM_IMP	0x06000000	/* No cache, imprecise */
+#define CACR_DCINVA	0x01000000	/* Invalidate data cache */
+#define CACR_BEC	0x00080000	/* Enable branch cache */
+#define CACR_BCINVA	0x00040000	/* Invalidate branch cache */
+#define CACR_IEC	0x00008000	/* Enable instruction cache */
+#define CACR_DNFB	0x00002000	/* Inhibited fill buffer */
+#define CACR_IDPI	0x00001000	/* Disable CPUSHL */
+#define CACR_IHLCK	0x00000800	/* Intruction cache half lock */
+#define CACR_IDCM	0x00000400	/* Intruction cache inhibit */
+#define CACR_ICINVA	0x00000100	/* Invalidate instr cache */
+#define CACR_EUSP	0x00000020	/* Enable separate user a7 */
+
+#define ACR_BASE_POS	24		/* Address Base */
+#define ACR_MASK_POS	16		/* Address Mask */
+#define ACR_ENABLE	0x00008000	/* Enable address */
+#define ACR_USER	0x00000000	/* User mode access only */
+#define ACR_SUPER	0x00002000	/* Supervisor mode only */
+#define ACR_ANY		0x00004000	/* Match any access mode */
+#define ACR_CM_WT	0x00000000	/* Write through mode */
+#define ACR_CM_CP	0x00000020	/* Copyback mode */
+#define ACR_CM_OFF_PRE	0x00000040	/* No cache, precise */
+#define ACR_CM_OFF_IMP	0x00000060	/* No cache, imprecise */
+#define ACR_CM		0x00000060	/* Cache mode mask */
+#define ACR_WPROTECT	0x00000004	/* Write protect */
+
+#if defined(CONFIG_M5407)
+
+#define ICACHE_SIZE 0x4000	/* instruction - 16k */
+#define DCACHE_SIZE 0x2000	/* data - 8k */
+
+#elif defined(CONFIG_M54xx)
+
+#define ICACHE_SIZE 0x8000	/* instruction - 32k */
+#define DCACHE_SIZE 0x8000	/* data - 32k */
+
+#endif
+
+#define CACHE_LINE_SIZE 0x0010	/* 16 bytes */
+#define CACHE_WAYS 4		/* 4 ways */
+
+/*
+ *	Version 4 cores have a true harvard style separate instruction
+ *	and data cache. Enable data and instruction caches, also enable write
+ *	buffers and branch accelerator.
+ */
+/* attention : enabling CACR_DESB requires a "nop" to flush the store buffer */
+/* use '+' instead of '|' for assembler's sake */
+
+	/* Enable data cache */
+	/* Enable data store buffer */
+	/* outside ACRs : No cache, precise */
+	/* Enable instruction+branch caches */
+#if defined(CONFIG_M5407)
+#define CACHE_MODE (CACR_DEC+CACR_DESB+CACR_DDCM_P+CACR_BEC+CACR_IEC)
+#else
+#define CACHE_MODE (CACR_DEC+CACR_DESB+CACR_DDCM_P+CACR_BEC+CACR_IEC+CACR_EUSP)
+#endif
+#if defined(CONFIG_CACHE_COPYBACK)
+#define DATA_CACHE_MODE (ACR_ENABLE+ACR_ANY+ACR_CM_CP)
+#else
+#define DATA_CACHE_MODE (ACR_ENABLE+ACR_ANY+ACR_CM_WT)
+#endif
+#define INSN_CACHE_MODE (ACR_ENABLE+ACR_ANY)
+
+#define CACHE_INIT	(CACR_DCINVA+CACR_BCINVA+CACR_ICINVA)
+#define CACHE_INVALIDATE  (CACHE_MODE+CACR_DCINVA+CACR_BCINVA+CACR_ICINVA)
+#define CACHE_INVALIDATEI (CACHE_MODE+CACR_BCINVA+CACR_ICINVA)
+#define CACHE_INVALIDATED (CACHE_MODE+CACR_DCINVA)
+#define ACR0_MODE	(0x000f0000+DATA_CACHE_MODE)
+#define ACR1_MODE	0
+#define ACR2_MODE	(0x000f0000+INSN_CACHE_MODE)
+#define ACR3_MODE	0
+
+#if ((DATA_CACHE_MODE & ACR_CM) == ACR_CM_CP)
+/* Copyback cache mode must push dirty cache lines first */
+#define	CACHE_PUSH
+#endif
+
+#endif	/* m54xxacr_h */
--- a/arch/m68k/include/asm/m54xxgpt.h
+++ b/arch/m68k/include/asm/m54xxgpt.h
@ -1,13 +1,13 @@
 /*
- * File:	m548xgpt.h
- * Purpose:	Register and bit definitions for the MCF548X
+ * File:	m54xxgpt.h
+ * Purpose:	Register and bit definitions for the MCF54XX
 *
 * Notes:
 *
 */

-#ifndef m548xgpt_h
-#define m548xgpt_h
+#ifndef m54xxgpt_h
+#define m54xxgpt_h

 /*********************************************************************
 *
@ -87,4 +87,4 @@

 /********************************************************************/

-#endif /* m548xgpt_h */
+#endif /* m54xxgpt_h */
--- a/arch/m68k/include/asm/m54xxsim.h
+++ b/arch/m68k/include/asm/m54xxsim.h
@ -1,9 +1,14 @@
 /*
- *	m548xsim.h -- ColdFire 547x/548x System Integration Unit support.
+ *	m54xxsim.h -- ColdFire 547x/548x System Integration Unit support.
 */

-#ifndef	m548xsim_h
-#define m548xsim_h
+#ifndef	m54xxsim_h
+#define m54xxsim_h
+
+#define	CPU_NAME		"COLDFIRE(m54xx)"
+#define	CPU_INSTR_PER_JIFFY	2
+
+#include <asm/m54xxacr.h>

 #define MCFINT_VECBASE		64

@ -21,6 +26,14 @@
 #define MCFINTC_IACKL		0x19		/* */
 #define MCFINTC_ICR0		0x40		/* Base ICR register */

+/*
+ *	UART module.
+ */
+#define MCFUART_BASE1		0x8600		/* Base address of UART1 */
+#define MCFUART_BASE2		0x8700		/* Base address of UART2 */
+#define MCFUART_BASE3		0x8800		/* Base address of UART3 */
+#define MCFUART_BASE4		0x8900		/* Base address of UART4 */
+
 /*
 *	Define system peripheral IRQ usage.
 */
@ -52,4 +65,4 @@
 #define MCF_PAR_PSC_RTS_RTS	(0x30)
 #define MCF_PAR_PSC_CANRX	(0x40)

-#endif	/* m548xsim_h */
+#endif	/* m54xxsim_h */
--- a/arch/m68k/include/asm/mcfcache.h
+++ b/arch/m68k/include/asm/mcfcache.h
@ -1,150 +0,0 @@
-/****************************************************************************/
-
-/*
- *	mcfcache.h -- ColdFire CPU cache support code
- *
- *	(C) Copyright 2004, Greg Ungerer <gerg@snapgear.com>
- */
-
-/****************************************************************************/
-#ifndef	__M68KNOMMU_MCFCACHE_H
-#define	__M68KNOMMU_MCFCACHE_H
-/****************************************************************************/
-
-
-/*
- *	The different ColdFire families have different cache arrangments.
- *	Everything from a small instruction only cache, to configurable
- *	data and/or instruction cache, to unified instruction/data, to 
- *	harvard style separate instruction and data caches.
- */
-
-#if defined(CONFIG_M5206) || defined(CONFIG_M5206e) || defined(CONFIG_M5272)
-/*
- *	Simple version 2 core cache. These have instruction cache only,
- *	we just need to invalidate it and enable it.
- */
-.macro CACHE_ENABLE
-	movel	#0x01000000,%d0		/* invalidate cache cmd */
-	movec	%d0,%CACR		/* do invalidate cache */
-	movel	#0x80000100,%d0		/* setup cache mask */
-	movec	%d0,%CACR		/* enable cache */
-.endm
-#endif /* CONFIG_M5206 || CONFIG_M5206e || CONFIG_M5272 */
-
-#if defined(CONFIG_M523x) || defined(CONFIG_M527x)
-/*
- *	New version 2 cores have a configurable split cache arrangement.
- *	For now I am just enabling instruction cache - but ultimately I
- *	think a split instruction/data cache would be better.
- */
-.macro CACHE_ENABLE
-	movel	#0x01400000,%d0
-	movec	%d0,%CACR		/* invalidate cache */
-	nop
-	movel	#0x0000c000,%d0		/* set SDRAM cached only */
-	movec	%d0,%ACR0
-	movel	#0x00000000,%d0		/* no other regions cached */
-	movec	%d0,%ACR1
-	movel	#0x80400100,%d0		/* configure cache */
-	movec	%d0,%CACR		/* enable cache */
-	nop
-.endm
-#endif /* CONFIG_M523x || CONFIG_M527x */
-
-#if defined(CONFIG_M528x)
-.macro CACHE_ENABLE
-	nop
-	movel	#0x01000000, %d0
-	movec	%d0, %CACR		/* Invalidate cache */
-	nop
-	movel	#0x0000c020, %d0	/* Set SDRAM cached only */
-	movec	%d0, %ACR0
-	movel	#0x00000000, %d0	/* No other regions cached */
-	movec	%d0, %ACR1
-	movel	#0x80000200, %d0	/* Setup cache mask */
-	movec	%d0, %CACR		/* Enable cache */
-	nop
-.endm
-#endif /* CONFIG_M528x */
-
-#if defined(CONFIG_M5249) || defined(CONFIG_M5307)
-/*
- *	The version 3 core cache. Oddly enough the version 2 core 5249
- *	has the same SDRAM and cache setup as the version 3 cores.
- *	This is a single unified instruction/data cache.
- */
-.macro CACHE_ENABLE
-	movel	#0x01000000,%d0		/* invalidate whole cache */
-	movec	%d0,%CACR
-	nop
-#if defined(DEBUGGER_COMPATIBLE_CACHE) || defined(CONFIG_SECUREEDGEMP3)
-	movel	#0x0000c000,%d0		/* set SDRAM cached (write-thru) */
-#else
-	movel	#0x0000c020,%d0		/* set SDRAM cached (copyback) */
-#endif
-	movec	%d0,%ACR0
-	movel	#0x00000000,%d0		/* no other regions cached */
-	movec	%d0,%ACR1
-	movel	#0xa0000200,%d0		/* enable cache */
-	movec	%d0,%CACR
-	nop
-.endm
-#endif /* CONFIG_M5249 || CONFIG_M5307 */
-
-#if defined(CONFIG_M532x)
-.macro CACHE_ENABLE
-	movel	#0x01000000,%d0		/* invalidate cache cmd */
-	movec	%d0,%CACR		/* do invalidate cache */
-	nop
-	movel	#0x4001C000,%d0		/* set SDRAM cached (write-thru) */
-	movec	%d0,%ACR0
-	movel	#0x00000000,%d0		/* no other regions cached */
-	movec	%d0,%ACR1
-	movel	#0x80000200,%d0		/* setup cache mask */
-	movec	%d0,%CACR		/* enable cache */
-	nop
-.endm
-#endif /* CONFIG_M532x */
-
-#if defined(CONFIG_M5407) || defined(CONFIG_M548x)
-/*
- *	Version 4 cores have a true harvard style separate instruction
- *	and data cache. Invalidate and enable cache, also enable write
- *	buffers and branch accelerator.
- */
-.macro CACHE_ENABLE
-	movel	#0x01040100,%d0		/* invalidate whole cache */
-	movec	%d0,%CACR
-	nop
-	movel	#0x000fc000,%d0		/* set SDRAM cached only */
-	movec	%d0, %ACR0
-	movel	#0x00000000,%d0		/* no other regions cached */
-	movec	%d0, %ACR1
-	movel	#0x000fc000,%d0		/* set SDRAM cached only */
-	movec	%d0, %ACR2
-	movel	#0x00000000,%d0		/* no other regions cached */
-	movec	%d0, %ACR3
-	movel	#0xb6088400,%d0		/* enable caches */
-	movec	%d0,%CACR
-	nop
-.endm
-#endif /* CONFIG_M5407 */
-
-#if defined(CONFIG_M520x)
-.macro CACHE_ENABLE
-	move.l	#0x01000000,%d0		/* invalidate whole cache */
-	movec	%d0,%CACR
-	nop
-	move.l	#0x0000c000,%d0		/* set SDRAM cached (write-thru) */
-	movec	%d0,%ACR0
-	move.l	#0x00000000,%d0		/* no other regions cached */
-	movec	%d0,%ACR1
-	move.l	#0x80400000,%d0		/* enable 8K instruction cache */
-	movec	%d0,%CACR
-	nop
-.endm
-#endif /* CONFIG_M520x */
-
-/****************************************************************************/
-#endif	/* __M68KNOMMU_MCFCACHE_H */
--- a/arch/m68k/include/asm/mcfsim.h
+++ b/arch/m68k/include/asm/mcfsim.h
@ -41,8 +41,8 @@
 #elif defined(CONFIG_M5407)
 #include <asm/m5407sim.h>
 #include <asm/mcfintc.h>
-#elif defined(CONFIG_M548x)
-#include <asm/m548xsim.h>
+#elif defined(CONFIG_M54xx)
+#include <asm/m54xxsim.h>
 #endif

 /****************************************************************************/
--- a/arch/m68k/include/asm/mcfuart.h
+++ b/arch/m68k/include/asm/mcfuart.h
@ -12,49 +12,6 @@
 #define	mcfuart_h
 /****************************************************************************/

-/*
- *	Define the base address of the UARTS within the MBAR address
- *	space.
- */
-#if defined(CONFIG_M5272)
-#define	MCFUART_BASE1		0x100		/* Base address of UART1 */
-#define	MCFUART_BASE2		0x140		/* Base address of UART2 */
-#elif defined(CONFIG_M5206) || defined(CONFIG_M5206e)
-#if defined(CONFIG_NETtel)
-#define	MCFUART_BASE1		0x180		/* Base address of UART1 */
-#define	MCFUART_BASE2		0x140		/* Base address of UART2 */
-#else
-#define	MCFUART_BASE1		0x140		/* Base address of UART1 */
-#define	MCFUART_BASE2		0x180		/* Base address of UART2 */
-#endif
-#elif defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x)
-#define MCFUART_BASE1		0x200           /* Base address of UART1 */
-#define MCFUART_BASE2		0x240           /* Base address of UART2 */
-#define MCFUART_BASE3		0x280           /* Base address of UART3 */
-#elif defined(CONFIG_M5249) || defined(CONFIG_M5307) || defined(CONFIG_M5407)
-#if defined(CONFIG_NETtel) || defined(CONFIG_SECUREEDGEMP3)
-#define MCFUART_BASE1		0x200           /* Base address of UART1 */
-#define MCFUART_BASE2		0x1c0           /* Base address of UART2 */
-#else
-#define MCFUART_BASE1		0x1c0           /* Base address of UART1 */
-#define MCFUART_BASE2		0x200           /* Base address of UART2 */
-#endif
-#elif defined(CONFIG_M520x)
-#define MCFUART_BASE1		0x60000		/* Base address of UART1 */
-#define MCFUART_BASE2		0x64000		/* Base address of UART2 */
-#define MCFUART_BASE3		0x68000		/* Base address of UART2 */
-#elif defined(CONFIG_M532x)
-#define MCFUART_BASE1		0xfc060000	/* Base address of UART1 */
-#define MCFUART_BASE2		0xfc064000	/* Base address of UART2 */
-#define MCFUART_BASE3		0xfc068000	/* Base address of UART3 */
-#elif defined(CONFIG_M548x)
-#define MCFUART_BASE1		0x8600		/* on M548x */
-#define MCFUART_BASE2		0x8700		/* on M548x */
-#define MCFUART_BASE3		0x8800		/* on M548x */
-#define MCFUART_BASE4		0x8900		/* on M548x */
-#endif
-
-
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>

@ -217,7 +174,7 @@ struct mcf_platform_uart {
 #define	MCFUART_URF_RXS		0xc0		/* Receiver status */
 #endif

-#if defined(CONFIG_M548x)
+#if defined(CONFIG_M54xx)
 #define MCFUART_TXFIFOSIZE	512
 #elif defined(CONFIG_M5272)
 #define MCFUART_TXFIFOSIZE	25
--- a/arch/m68k/include/asm/processor.h
+++ b/arch/m68k/include/asm/processor.h
@ -20,23 +20,26 @@

 static inline unsigned long rdusp(void)
 {
-#ifdef CONFIG_COLDFIRE
+#ifdef CONFIG_COLDFIRE_SW_A7
 	extern unsigned int sw_usp;
 	return sw_usp;
 #else
-	unsigned long usp;
-	__asm__ __volatile__("move %/usp,%0" : "=a" (usp));
+	register unsigned long usp __asm__("a0");
+	/* move %usp,%a0 */
+	__asm__ __volatile__(".word 0x4e68" : "=a" (usp));
 	return usp;
 #endif
 }

 static inline void wrusp(unsigned long usp)
 {
-#ifdef CONFIG_COLDFIRE
+#ifdef CONFIG_COLDFIRE_SW_A7
 	extern unsigned int sw_usp;
 	sw_usp = usp;
 #else
-	__asm__ __volatile__("move %0,%/usp" : : "a" (usp));
+	register unsigned long a0 __asm__("a0") = usp;
+	/* move %a0,%usp */
+	__asm__ __volatile__(".word 0x4e60" : : "a" (a0) );
 #endif
 }

--- a/arch/m68knommu/Kconfig
+++ b/arch/m68knommu/Kconfig
@ -75,6 +75,16 @@ config GENERIC_CLOCKEVENTS
 config NO_IOPORT
 	def_bool y

+config COLDFIRE_SW_A7
+	bool
+	default n
+
+config HAVE_CACHE_SPLIT
+	bool
+
+config HAVE_CACHE_CB
+	bool
+
 source "init/Kconfig"

 source "kernel/Kconfig.freezer"
@ -107,69 +117,90 @@ config M68360

 config M5206
 	bool "MCF5206"
+	select COLDFIRE_SW_A7
 	help
 	  Motorola ColdFire 5206 processor support.

 config M5206e
 	bool "MCF5206e"
+	select COLDFIRE_SW_A7
 	help
 	  Motorola ColdFire 5206e processor support.

 config M520x
 	bool "MCF520x"
 	select GENERIC_CLOCKEVENTS
+	select HAVE_CACHE_SPLIT
 	help
 	   Freescale Coldfire 5207/5208 processor support.

 config M523x
 	bool "MCF523x"
 	select GENERIC_CLOCKEVENTS
+	select HAVE_CACHE_SPLIT
 	help
 	  Freescale Coldfire 5230/1/2/4/5 processor support

 config M5249
 	bool "MCF5249"
+	select COLDFIRE_SW_A7
 	help
 	  Motorola ColdFire 5249 processor support.

 config M5271
 	bool "MCF5271"
+	select HAVE_CACHE_SPLIT
 	help
 	  Freescale (Motorola) ColdFire 5270/5271 processor support.

 config M5272
 	bool "MCF5272"
+	select COLDFIRE_SW_A7
 	help
 	  Motorola ColdFire 5272 processor support.

 config M5275
 	bool "MCF5275"
+	select HAVE_CACHE_SPLIT
 	help
 	  Freescale (Motorola) ColdFire 5274/5275 processor support.

 config M528x
 	bool "MCF528x"
 	select GENERIC_CLOCKEVENTS
+	select HAVE_CACHE_SPLIT
 	help
 	  Motorola ColdFire 5280/5282 processor support.

 config M5307
 	bool "MCF5307"
+	select COLDFIRE_SW_A7
+	select HAVE_CACHE_CB
 	help
 	  Motorola ColdFire 5307 processor support.

 config M532x
 	bool "MCF532x"
+	select HAVE_CACHE_CB
 	help
 	  Freescale (Motorola) ColdFire 532x processor support.

 config M5407
 	bool "MCF5407"
+	select COLDFIRE_SW_A7
+	select HAVE_CACHE_CB
 	help
 	  Motorola ColdFire 5407 processor support.

+config M547x
+	bool "MCF547x"
+	select HAVE_CACHE_CB
+	help
+	  Freescale ColdFire 5470/5471/5472/5473/5474/5475 processor support.
+
 config M548x
 	bool "MCF548x"
+	select HAVE_CACHE_CB
 	help
 	  Freescale ColdFire 5480/5481/5482/5483/5484/5485 processor support.

@ -181,9 +212,14 @@ config M527x
 	select GENERIC_CLOCKEVENTS
 	default y

+config M54xx
+	bool
+	depends on (M548x || M547x)
+	default y
+
 config COLDFIRE
 	bool
-	depends on (M5206 || M5206e || M520x || M523x || M5249 || M527x || M5272 || M528x || M5307 || M532x || M5407 || M548x)
+	depends on (M5206 || M5206e || M520x || M523x || M5249 || M527x || M5272 || M528x || M5307 || M532x || M5407 || M54xx)
 	select GENERIC_GPIO
 	select ARCH_REQUIRE_GPIOLIB
 	default y
@ -230,6 +266,46 @@ config OLDMASK
 	  Build support for the older revision ColdFire 5307 silicon.
 	  Specifically this is the 1H55J mask revision.

+if HAVE_CACHE_SPLIT
+choice
+	prompt "Split Cache Configuration"
+	default CACHE_I
+
+config CACHE_I
+	bool "Instruction"
+	help
+	  Use all of the ColdFire CPU cache memory as an instruction cache.
+
+config CACHE_D
+	bool "Data"
+	help
+	  Use all of the ColdFire CPU cache memory as a data cache.
+
+config CACHE_BOTH
+	bool "Both"
+	help
+	  Split the ColdFire CPU cache, and use half as an instruction cache
+	  and half as a data cache.
+endchoice
+endif
+
+if HAVE_CACHE_CB
+choice
+	prompt "Data cache mode"
+	default CACHE_WRITETHRU
+
+config CACHE_WRITETHRU
+	bool "Write-through"
+	help
+	  The ColdFire CPU cache is set into Write-through mode.
+
+config CACHE_COPYBACK
+	bool "Copy-back"
+	help
+	  The ColdFire CPU cache is set into Copy-back mode.
+endchoice
+endif
+
 comment "Platform"

 config PILOT3
--- a/arch/m68knommu/Makefile
+++ b/arch/m68knommu/Makefile
@ -25,7 +25,7 @@ platform-$(CONFIG_M528x)	:= 528x
 platform-$(CONFIG_M5307)	:= 5307
 platform-$(CONFIG_M532x)	:= 532x
 platform-$(CONFIG_M5407)	:= 5407
-platform-$(CONFIG_M548x)	:= 548x
+platform-$(CONFIG_M54xx)	:= 54xx
 PLATFORM := $(platform-y)

 board-$(CONFIG_PILOT)		:= pilot
@ -74,7 +74,7 @@ cpuclass-$(CONFIG_M528x)	:= coldfire
 cpuclass-$(CONFIG_M5307)	:= coldfire
 cpuclass-$(CONFIG_M532x)	:= coldfire
 cpuclass-$(CONFIG_M5407)	:= coldfire
-cpuclass-$(CONFIG_M548x)	:= coldfire
+cpuclass-$(CONFIG_M54xx)	:= coldfire
 cpuclass-$(CONFIG_M68328)	:= 68328
 cpuclass-$(CONFIG_M68EZ328)	:= 68328
 cpuclass-$(CONFIG_M68VZ328)	:= 68328
@ -91,18 +91,18 @@ export PLATFORM BOARD MODEL CPUCLASS
 # Some CFLAG additions based on specific CPU type.
 #
 cflags-$(CONFIG_M5206)		:= $(call cc-option,-mcpu=5206,-m5200)
-cflags-$(CONFIG_M5206e)		:= $(call cc-option,-m5206e,-m5200)
+cflags-$(CONFIG_M5206e)		:= $(call cc-option,-mcpu=5206e,-m5200)
 cflags-$(CONFIG_M520x)		:= $(call cc-option,-mcpu=5208,-m5200)
 cflags-$(CONFIG_M523x)		:= $(call cc-option,-mcpu=523x,-m5307)
 cflags-$(CONFIG_M5249)		:= $(call cc-option,-mcpu=5249,-m5200)
 cflags-$(CONFIG_M5271)		:= $(call cc-option,-mcpu=5271,-m5307)
 cflags-$(CONFIG_M5272)		:= $(call cc-option,-mcpu=5272,-m5307)
 cflags-$(CONFIG_M5275)		:= $(call cc-option,-mcpu=5275,-m5307)
-cflags-$(CONFIG_M528x)		:= $(call cc-option,-m528x,-m5307)
-cflags-$(CONFIG_M5307)		:= $(call cc-option,-m5307,-m5200)
+cflags-$(CONFIG_M528x)		:= $(call cc-option,-mcpu=528x,-m5307)
+cflags-$(CONFIG_M5307)		:= $(call cc-option,-mcpu=5307,-m5200)
 cflags-$(CONFIG_M532x)		:= $(call cc-option,-mcpu=532x,-m5307)
-cflags-$(CONFIG_M5407)		:= $(call cc-option,-m5407,-m5200)
-cflags-$(CONFIG_M548x)		:= $(call cc-option,-m5407,-m5200)
+cflags-$(CONFIG_M5407)		:= $(call cc-option,-mcpu=5407,-m5200)
+cflags-$(CONFIG_M54xx)		:= $(call cc-option,-mcpu=5475,-m5200)
 cflags-$(CONFIG_M68328)		:= -m68000
 cflags-$(CONFIG_M68EZ328)	:= -m68000
 cflags-$(CONFIG_M68VZ328)	:= -m68000
--- a/arch/m68knommu/kernel/setup.c
+++ b/arch/m68knommu/kernel/setup.c
@ -55,55 +55,29 @@ void (*mach_halt)(void);
 void (*mach_power_off)(void);

 #ifdef CONFIG_M68328
-	#define CPU "MC68328"
+#define CPU_NAME	"MC68328"
 #endif
 #ifdef CONFIG_M68EZ328
-	#define CPU "MC68EZ328"
+#define CPU_NAME	"MC68EZ328"
 #endif
 #ifdef CONFIG_M68VZ328
-	#define CPU "MC68VZ328"
+#define CPU_NAME	"MC68VZ328"
 #endif
 #ifdef CONFIG_M68360
-	#define CPU "MC68360"
+#define CPU_NAME	"MC68360"
 #endif
-#if defined(CONFIG_M5206)
-	#define	CPU "COLDFIRE(m5206)"
+#ifndef CPU_NAME
+#define	CPU_NAME	"UNKNOWN"
 #endif
-#if defined(CONFIG_M5206e)
-	#define	CPU "COLDFIRE(m5206e)"
-#endif
-#if defined(CONFIG_M520x)
-	#define CPU "COLDFIRE(m520x)"
-#endif
-#if defined(CONFIG_M523x)
-	#define CPU "COLDFIRE(m523x)"
-#endif
-#if defined(CONFIG_M5249)
-	#define CPU "COLDFIRE(m5249)"
-#endif
-#if defined(CONFIG_M5271)
-	#define CPU "COLDFIRE(m5270/5271)"
-#endif
-#if defined(CONFIG_M5272)
-	#define CPU "COLDFIRE(m5272)"
-#endif
-#if defined(CONFIG_M5275)
-	#define CPU "COLDFIRE(m5274/5275)"
-#endif
-#if defined(CONFIG_M528x)
-	#define CPU "COLDFIRE(m5280/5282)"
-#endif
-#if defined(CONFIG_M5307)
-	#define	CPU "COLDFIRE(m5307)"
-#endif
-#if defined(CONFIG_M532x)
-	#define	CPU "COLDFIRE(m532x)"
-#endif
-#if defined(CONFIG_M5407)
-	#define	CPU "COLDFIRE(m5407)"
-#endif
-#ifndef CPU
-	#define	CPU "UNKNOWN"
+
+/*
+ * Different cores have different instruction execution timings.
+ * The old/traditional 68000 cores are basically all the same, at 16.
+ * The ColdFire cores vary a little, their values are defined in their
+ * headers. We default to the standard 68000 value here.
+ */
+#ifndef CPU_INSTR_PER_JIFFY
+#define	CPU_INSTR_PER_JIFFY	16
 #endif

 extern int _stext, _etext, _sdata, _edata, _sbss, _ebss, _end;
@ -208,7 +182,7 @@ void __init setup_arch(char **cmdline_p)
 	command_line[sizeof(command_line) - 1] = 0;
 #endif /* CONFIG_UBOOT */

-	printk(KERN_INFO "\x0F\r\n\nuClinux/" CPU "\n");
+	printk(KERN_INFO "\x0F\r\n\nuClinux/" CPU_NAME "\n");

 #ifdef CONFIG_UCDIMM
 	printk(KERN_INFO "uCdimm by Lineo, Inc. <www.lineo.com>\n");
@ -257,11 +231,6 @@ void __init setup_arch(char **cmdline_p)
 	memcpy(boot_command_line, command_line, COMMAND_LINE_SIZE);
 	boot_command_line[COMMAND_LINE_SIZE-1] = 0;

-#ifdef DEBUG
-	if (strlen(*cmdline_p))
-		printk(KERN_DEBUG "Command line: '%s'\n", *cmdline_p);
-#endif
-
 #if defined(CONFIG_FRAMEBUFFER_CONSOLE) && defined(CONFIG_DUMMY_CONSOLE)
 	conswitchp = &dummy_con;
 #endif
@ -303,15 +272,10 @@ static int show_cpuinfo(struct seq_file *m, void *v)
 	char *cpu, *mmu, *fpu;
 	u_long clockfreq;

-	cpu = CPU;
+	cpu = CPU_NAME;
 	mmu = "none";
 	fpu = "none";
-
-#ifdef CONFIG_COLDFIRE
-	clockfreq = (loops_per_jiffy * HZ) * 3;
-#else
-	clockfreq = (loops_per_jiffy * HZ) * 16;
-#endif
+	clockfreq = (loops_per_jiffy * HZ) * CPU_INSTR_PER_JIFFY;

 	seq_printf(m, "CPU:\t\t%s\n"
 		      "MMU:\t\t%s\n"
--- a/arch/m68knommu/mm/Makefile
+++ b/arch/m68knommu/mm/Makefile
@ -2,4 +2,4 @@
 # Makefile for the linux m68knommu specific parts of the memory manager.
 #

-obj-y += init.o fault.o memory.o kmap.o
+obj-y += init.o kmap.o
--- a/arch/m68knommu/mm/fault.c
+++ b/arch/m68knommu/mm/fault.c
@ -1,57 +0,0 @@
-/*
- *  linux/arch/m68knommu/mm/fault.c
- *
- *  Copyright (C) 1998  D. Jeff Dionne <jeff@lineo.ca>,
- *  Copyright (C) 2000  Lineo, Inc.  (www.lineo.com)
- *
- *  Based on:
- *
- *  linux/arch/m68k/mm/fault.c
- *
- *  Copyright (C) 1995  Hamish Macdonald
- */
-
-#include <linux/mman.h>
-#include <linux/mm.h>
-#include <linux/kernel.h>
-#include <linux/ptrace.h>
-
-#include <asm/system.h>
-#include <asm/pgtable.h>
-
-extern void die_if_kernel(char *, struct pt_regs *, long);
-
-/*
- * This routine handles page faults.  It determines the problem, and
- * then passes it off to one of the appropriate routines.
- *
- * error_code:
- *	bit 0 == 0 means no page found, 1 means protection fault
- *	bit 1 == 0 means read, 1 means write
- *
- * If this routine detects a bad access, it returns 1, otherwise it
- * returns 0.
- */
-asmlinkage int do_page_fault(struct pt_regs *regs, unsigned long address,
-			      unsigned long error_code)
-{
-#ifdef DEBUG
-	printk(KERN_DEBUG "regs->sr=%#x, regs->pc=%#lx, address=%#lx, %ld\n",
-		regs->sr, regs->pc, address, error_code);
-#endif
-
-	/*
-	 * Oops. The kernel tried to access some bad page. We'll have to
-	 * terminate things with extreme prejudice.
-	 */
-	if ((unsigned long) address < PAGE_SIZE)
-		printk(KERN_ALERT "Unable to handle kernel NULL pointer dereference");
-	else
-		printk(KERN_ALERT "Unable to handle kernel access");
-	printk(KERN_ALERT " at virtual address %08lx\n", address);
-	die_if_kernel("Oops", regs, error_code);
-	do_exit(SIGKILL);
-
-	return 1;
-}
-
--- a/arch/m68knommu/mm/kmap.c
+++ b/arch/m68knommu/mm/kmap.c
@ -35,15 +35,6 @@ void iounmap(void *addr)
 {
 }

-/*
- * __iounmap unmaps nearly everything, so be careful
- * it doesn't free currently pointer/page tables anymore but it
- * wans't used anyway and might be added later.
- */
-void __iounmap(void *addr, unsigned long size)
-{
-}
-
 /*
 * Set new cache mode for some kernel address space.
 * The caller must push data for that range itself, if such data may already
--- a/arch/m68knommu/mm/memory.c
+++ b/arch/m68knommu/mm/memory.c
@ -1,33 +0,0 @@
-/*
- *  linux/arch/m68knommu/mm/memory.c
- *
- *  Copyright (C) 1998  Kenneth Albanowski <kjahds@kjahds.com>,
- *  Copyright (C) 1999-2002, Greg Ungerer (gerg@snapgear.com)
- *
- *  Based on:
- *
- *  linux/arch/m68k/mm/memory.c
- *
- *  Copyright (C) 1995  Hamish Macdonald
- */
-
-#include <linux/mm.h>
-#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/types.h>
-
-#include <asm/segment.h>
-#include <asm/page.h>
-#include <asm/pgtable.h>
-#include <asm/system.h>
-
-/*
- * Map some physical address range into the kernel address space.
- */
-
-unsigned long kernel_map(unsigned long paddr, unsigned long size,
-			 int nocacheflag, unsigned long *memavailp )
-{
-	return paddr;
-}
-
--- a/arch/m68knommu/platform/54xx/Makefile
+++ b/arch/m68knommu/platform/54xx/Makefile
--- a/arch/m68knommu/platform/54xx/config.c
+++ b/arch/m68knommu/platform/54xx/config.c
@ -1,7 +1,7 @@
 /***************************************************************************/

 /*
- *	linux/arch/m68knommu/platform/548x/config.c
+ *	linux/arch/m68knommu/platform/54xx/config.c
 *
 *	Copyright (C) 2010, Philippe De Muyter <phdm@macqel.be>
 */
@ -15,13 +15,13 @@
 #include <linux/io.h>
 #include <asm/machdep.h>
 #include <asm/coldfire.h>
-#include <asm/m548xsim.h>
+#include <asm/m54xxsim.h>
 #include <asm/mcfuart.h>
-#include <asm/m548xgpt.h>
+#include <asm/m54xxgpt.h>

 /***************************************************************************/

-static struct mcf_platform_uart m548x_uart_platform[] = {
+static struct mcf_platform_uart m54xx_uart_platform[] = {
 	{
 		.mapbase	= MCF_MBAR + MCFUART_BASE1,
 		.irq		= 64 + 35,
@ -40,20 +40,20 @@ static struct mcf_platform_uart m548x_uart_platform[] = {
 	},
 };

-static struct platform_device m548x_uart = {
+static struct platform_device m54xx_uart = {
 	.name			= "mcfuart",
 	.id			= 0,
-	.dev.platform_data	= m548x_uart_platform,
+	.dev.platform_data	= m54xx_uart_platform,
 };

-static struct platform_device *m548x_devices[] __initdata = {
-	&m548x_uart,
+static struct platform_device *m54xx_devices[] __initdata = {
+	&m54xx_uart,
 };


 /***************************************************************************/

-static void __init m548x_uart_init_line(int line, int irq)
+static void __init m54xx_uart_init_line(int line, int irq)
 {
 	int rts_cts;

@ -72,18 +72,18 @@ static void __init m548x_uart_init_line(int line, int irq)
 						MCF_MBAR + MCF_PAR_PSC(line));
 }

-static void __init m548x_uarts_init(void)
+static void __init m54xx_uarts_init(void)
 {
-	const int nrlines = ARRAY_SIZE(m548x_uart_platform);
+	const int nrlines = ARRAY_SIZE(m54xx_uart_platform);
 	int line;

 	for (line = 0; (line < nrlines); line++)
-		m548x_uart_init_line(line, m548x_uart_platform[line].irq);
+		m54xx_uart_init_line(line, m54xx_uart_platform[line].irq);
 }

 /***************************************************************************/

-static void mcf548x_reset(void)
+static void mcf54xx_reset(void)
 {
 	/* disable interrupts and enable the watchdog */
 	asm("movew #0x2700, %sr\n");
@ -97,8 +97,8 @@ static void mcf548x_reset(void)

 void __init config_BSP(char *commandp, int size)
 {
-	mach_reset = mcf548x_reset;
-	m548x_uarts_init();
+	mach_reset = mcf54xx_reset;
+	m54xx_uarts_init();
 }

 /***************************************************************************/
@ -106,7 +106,7 @@ void __init config_BSP(char *commandp, int size)
 static int __init init_BSP(void)
 {

-	platform_add_devices(m548x_devices, ARRAY_SIZE(m548x_devices));
+	platform_add_devices(m54xx_devices, ARRAY_SIZE(m54xx_devices));
 	return 0;
 }

--- a/arch/m68knommu/platform/68328/ints.c
+++ b/arch/m68knommu/platform/68328/ints.c
@ -179,8 +179,8 @@ void __init init_IRQ(void)
 	IMR = ~0;

 	for (i = 0; (i < NR_IRQS); i++) {
-		set_irq_chip(irq, &intc_irq_chip);
-		set_irq_handler(irq, handle_level_irq);
+		set_irq_chip(i, &intc_irq_chip);
+		set_irq_handler(i, handle_level_irq);
 	}
 }

--- a/arch/m68knommu/platform/coldfire/Makefile
+++ b/arch/m68knommu/platform/coldfire/Makefile
@ -14,7 +14,7 @@

 asflags-$(CONFIG_FULLDEBUG) := -DDEBUGGER_COMPATIBLE_CACHE=1

-obj-$(CONFIG_COLDFIRE)	+= clk.o dma.o entry.o vectors.o
+obj-$(CONFIG_COLDFIRE)	+= cache.o clk.o dma.o entry.o vectors.o
 obj-$(CONFIG_M5206)	+= timers.o intc.o
 obj-$(CONFIG_M5206e)	+= timers.o intc.o
 obj-$(CONFIG_M520x)	+= pit.o intc-simr.o
@ -26,7 +26,7 @@ obj-$(CONFIG_M528x)	+= pit.o intc-2.o
 obj-$(CONFIG_M5307)	+= timers.o intc.o
 obj-$(CONFIG_M532x)	+= timers.o intc-simr.o
 obj-$(CONFIG_M5407)	+= timers.o intc.o
-obj-$(CONFIG_M548x)	+= sltimers.o intc-2.o
+obj-$(CONFIG_M54xx)	+= sltimers.o intc-2.o

 obj-y			+= pinmux.o gpio.o
 extra-y := head.o
--- a/arch/m68knommu/platform/coldfire/cache.c
+++ b/arch/m68knommu/platform/coldfire/cache.c
@ -0,0 +1,48 @@
+/***************************************************************************/
+
+/*
+ *	cache.c -- general ColdFire Cache maintainence code
+ *
+ *	Copyright (C) 2010, Greg Ungerer (gerg@snapgear.com)
+ */
+
+/***************************************************************************/
+
+#include <linux/kernel.h>
+#include <asm/coldfire.h>
+#include <asm/mcfsim.h>
+
+/***************************************************************************/
+#ifdef CACHE_PUSH
+/***************************************************************************/
+
+/*
+ *	Use cpushl to push all dirty cache lines back to memory.
+ *	Older versions of GAS don't seem to know how to generate the
+ *	ColdFire cpushl instruction... Oh well, bit stuff it for now.
+ */
+
+void mcf_cache_push(void)
+{
+	__asm__ __volatile__ (
+		"clrl	%%d0\n\t"
+		"1:\n\t"
+		"movel	%%d0,%%a0\n\t"
+		"2:\n\t"
+		".word	0xf468\n\t"
+		"addl	%0,%%a0\n\t"
+		"cmpl	%1,%%a0\n\t"
+		"blt	2b\n\t"
+		"addql	#1,%%d0\n\t"
+		"cmpil	%2,%%d0\n\t"
+		"bne	1b\n\t"
+		: /* No output */
+		: "i" (CACHE_LINE_SIZE),
+		  "i" (DCACHE_SIZE / CACHE_WAYS),
+		  "i" (CACHE_WAYS)
+		: "d0", "a0" );
+}
+
+/***************************************************************************/
+#endif /* CACHE_PUSH */
+/***************************************************************************/
--- a/arch/m68knommu/platform/coldfire/entry.S
+++ b/arch/m68knommu/platform/coldfire/entry.S
@ -36,13 +36,16 @@
 #include <asm/asm-offsets.h>
 #include <asm/entry.h>

+#ifdef CONFIG_COLDFIRE_SW_A7
+/*
+ *	Define software copies of the supervisor and user stack pointers.
+ */
 .bss
-
 sw_ksp:
 .long	0
-
 sw_usp:
 .long	0
+#endif /* CONFIG_COLDFIRE_SW_A7 */

 .text

@ -51,7 +54,6 @@ sw_usp:
 .globl ret_from_exception
 .globl ret_from_signal
 .globl sys_call_table
-.globl ret_from_interrupt
 .globl inthandler
 .globl fasthandler

@ -140,20 +142,7 @@ Luser_return:
 	jne	Lwork_to_do		/* still work to do */

 Lreturn:
-	move	#0x2700,%sr		/* disable intrs */
-	movel	sw_usp,%a0		/* get usp */
-	movel	%sp@(PT_OFF_PC),%a0@-	/* copy exception program counter */
-	movel	%sp@(PT_OFF_FORMATVEC),%a0@- /* copy exception format/vector/sr */
-	moveml	%sp@,%d1-%d5/%a0-%a2
-	lea	%sp@(32),%sp		/* space for 8 regs */
-	movel	%sp@+,%d0
-	addql	#4,%sp			/* orig d0 */
-	addl	%sp@+,%sp		/* stk adj */
-	addql	#8,%sp			/* remove exception */
-	movel	%sp,sw_ksp		/* save ksp */
-	subql	#8,sw_usp		/* set exception */
-	movel	sw_usp,%sp		/* restore usp */
-	rte
+	RESTORE_USER

 Lwork_to_do:
 	movel	%a0@(TI_FLAGS),%d1	/* get thread_info->flags */
@ -191,31 +180,7 @@ ENTRY(inthandler)
 	jbsr	do_IRQ			/* call high level irq handler */
 	lea	%sp@(8),%sp		/* pop args off stack */

-	bra	ret_from_interrupt	/* this was fallthrough */
-
-/*
- * This is the fast interrupt handler (for certain hardware interrupt
- * sources). Unlike the normal interrupt handler it just uses the
- * current stack (doesn't care if it is user or kernel). It also
- * doesn't bother doing the bottom half handlers.
- */
-ENTRY(fasthandler)
-	SAVE_LOCAL
-
-	movew	%sp@(PT_OFF_FORMATVEC),%d0
-	andl	#0x03fc,%d0		/* mask out vector only */
-
-	movel	%sp,%sp@-		/* push regs arg */
-	lsrl	#2,%d0			/* calculate real vector # */
-	movel	%d0,%sp@-		/* push vector number */
-	jbsr	do_IRQ			/* call high level irq handler */
-	lea	%sp@(8),%sp		/* pop args off stack */
-
-	RESTORE_LOCAL
-
-ENTRY(ret_from_interrupt)
-	/* the fasthandler is confusing me, haven't seen any user */
-	jmp	ret_from_exception
+	bra	ret_from_exception

 /*
 * Beware - when entering resume, prev (the current task) is
@ -226,9 +191,8 @@ ENTRY(ret_from_interrupt)
 */
 ENTRY(resume)
 	movel	%a0, %d1			/* get prev thread in d1 */
-
-	movel	sw_usp,%d0			/* save usp */
-	movel	%d0,%a0@(TASK_THREAD+THREAD_USP)
+	RDUSP
+	movel	%a2,%a0@(TASK_THREAD+THREAD_USP)

 	SAVE_SWITCH_STACK
 	movel	%sp,%a0@(TASK_THREAD+THREAD_KSP) /* save kernel stack pointer */
@ -236,5 +200,5 @@ ENTRY(resume)
 	RESTORE_SWITCH_STACK

 	movel	%a1@(TASK_THREAD+THREAD_USP),%a0 /* restore thread user stack */
-	movel	%a0, sw_usp
+	WRUSP
 	rts
--- a/arch/m68knommu/platform/coldfire/head.S
+++ b/arch/m68knommu/platform/coldfire/head.S
@ -3,7 +3,7 @@
 /*
 *	head.S -- common startup code for ColdFire CPUs.
 *
- *	(C) Copyright 1999-2006, Greg Ungerer <gerg@snapgear.com>.
+ *	(C) Copyright 1999-2010, Greg Ungerer <gerg@snapgear.com>.
 */

 /*****************************************************************************/
@ -13,7 +13,6 @@
 #include <linux/init.h>
 #include <asm/asm-offsets.h>
 #include <asm/coldfire.h>
-#include <asm/mcfcache.h>
 #include <asm/mcfsim.h>
 #include <asm/thread_info.h>

@ -173,10 +172,27 @@ _start:

 	/*
 	 *	Now that we know what the memory is, lets enable cache
-	 *	and get things moving. This is Coldfire CPU specific.
+	 *	and get things moving. This is Coldfire CPU specific. Not
+	 *	all version cores have identical cache register setup. But
+	 *	it is very similar. Define the exact settings in the headers
+	 *	then the code here is the same for all.
 	 */
-	CACHE_ENABLE				/* enable CPU cache */
-
+	movel	#CACHE_INIT,%d0			/* invalidate whole cache */
+	movec	%d0,%CACR
+	nop
+	movel	#ACR0_MODE,%d0			/* set RAM region for caching */
+	movec	%d0,%ACR0
+	movel	#ACR1_MODE,%d0			/* anything else to cache? */
+	movec	%d0,%ACR1
+#ifdef ACR2_MODE
+	movel	#ACR2_MODE,%d0
+	movec	%d0,%ACR2
+	movel	#ACR3_MODE,%d0
+	movec	%d0,%ACR3
+#endif
+	movel	#CACHE_MODE,%d0			/* enable cache */
+	movec	%d0,%CACR
+	nop

 #ifdef CONFIG_ROMFS_FS
 	/*