mirror of
https://github.com/FEX-Emu/linux.git
synced 2024-12-15 21:30:43 +00:00
hwmon: (f71882fg) Add support for the f71889fg (version 2)
This adds support for the Fintek f71889fg to the f71882fg driver, many thanks to Gerd v. Egidy for providing (remote) access to a machine which such an ic. Note that this bit of the patch: - val = SENSORS_LIMIT(val, 0, 255); + + if (data->type == f71889fg) + val = SENSORS_LIMIT(val, -128, 127); + else + val = SENSORS_LIMIT(val, 0, 127); Changes behaviour for already supported models, the new behaviour is correct as the already supported models have bit 7 of the involved registers fixed at 0, so the previous behaviour which allowed setting temp zone limits > 127 was not correct. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
This commit is contained in:
Hans de Goede
Jean Delvare
parent
fc16c56e69
commit
7669896f49
@ -14,6 +14,10 @@ Supported chips:
|
||||
Prefix: 'f71882fg'
|
||||
Addresses scanned: none, address read from Super I/O config space
|
||||
Datasheet: Available from the Fintek website
|
||||
* Fintek F71889FG
|
||||
Prefix: 'f71889fg'
|
||||
Addresses scanned: none, address read from Super I/O config space
|
||||
Datasheet: Should become available on the Fintek website soon
|
||||
* Fintek F8000
|
||||
Prefix: 'f8000'
|
||||
Addresses scanned: none, address read from Super I/O config space
|
||||
@ -51,6 +55,12 @@ supported. The right one to use depends on external circuitry on the
|
||||
motherboard, so the driver assumes that the BIOS set the method
|
||||
properly.
|
||||
|
||||
Note that the lowest numbered temperature zone trip point corresponds to
|
||||
to the border between the highest and one but highest temperature zones, and
|
||||
vica versa. So the temperature zone trip points 1-4 (or 1-2) go from high temp
|
||||
to low temp! This is how things are implemented in the IC, and the driver
|
||||
mimicks this.
|
||||
|
||||
There are 2 modes to specify the speed of the fan, PWM duty cycle (or DC
|
||||
voltage) mode, where 0-100% duty cycle (0-100% of 12V) is specified. And RPM
|
||||
mode where the actual RPM of the fan (as measured) is controlled and the speed
|
||||
|
||||
@ -305,12 +305,12 @@ config SENSORS_F71805F
|
||||
will be called f71805f.
|
||||
|
||||
config SENSORS_F71882FG
|
||||
tristate "Fintek F71858FG, F71862FG, F71882FG and F8000"
|
||||
tristate "Fintek F71858FG, F71862FG, F71882FG, F71889FG and F8000"
|
||||
depends on EXPERIMENTAL
|
||||
help
|
||||
If you say yes here you get support for hardware monitoring
|
||||
features of the Fintek F71858FG, F71862FG/71863FG, F71882FG/F71883FG
|
||||
and F8000 Super-I/O chips.
|
||||
features of the Fintek F71858FG, F71862FG/71863FG, F71882FG/F71883FG,
|
||||
F71889FG and F8000 Super-I/O chips.
|
||||
|
||||
This driver can also be built as a module. If so, the module
|
||||
will be called f71882fg.
|
||||
|
||||
@ -48,6 +48,7 @@
|
||||
#define SIO_F71858_ID 0x0507 /* Chipset ID */
|
||||
#define SIO_F71862_ID 0x0601 /* Chipset ID */
|
||||
#define SIO_F71882_ID 0x0541 /* Chipset ID */
|
||||
#define SIO_F71889_ID 0x0723 /* Chipset ID */
|
||||
#define SIO_F8000_ID 0x0581 /* Chipset ID */
|
||||
|
||||
#define REGION_LENGTH 8
|
||||
@ -95,12 +96,13 @@ static unsigned short force_id;
|
||||
module_param(force_id, ushort, 0);
|
||||
MODULE_PARM_DESC(force_id, "Override the detected device ID");
|
||||
|
||||
enum chips { f71858fg, f71862fg, f71882fg, f8000 };
|
||||
enum chips { f71858fg, f71862fg, f71882fg, f71889fg, f8000 };
|
||||
|
||||
static const char *f71882fg_names[] = {
|
||||
"f71858fg",
|
||||
"f71862fg",
|
||||
"f71882fg",
|
||||
"f71889fg",
|
||||
"f8000",
|
||||
};
|
||||
|
||||
@ -155,7 +157,7 @@ struct f71882fg_data {
|
||||
u8 pwm_auto_point_hyst[2];
|
||||
u8 pwm_auto_point_mapping[4];
|
||||
u8 pwm_auto_point_pwm[4][5];
|
||||
u8 pwm_auto_point_temp[4][4];
|
||||
s8 pwm_auto_point_temp[4][4];
|
||||
};
|
||||
|
||||
/* Sysfs in */
|
||||
@ -945,7 +947,7 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev)
|
||||
/* Update once every 60 seconds */
|
||||
if ( time_after(jiffies, data->last_limits + 60 * HZ ) ||
|
||||
!data->valid) {
|
||||
if (data->type == f71882fg) {
|
||||
if (data->type == f71882fg || data->type == f71889fg) {
|
||||
data->in1_max =
|
||||
f71882fg_read8(data, F71882FG_REG_IN1_HIGH);
|
||||
data->in_beep =
|
||||
@ -967,7 +969,8 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev)
|
||||
F71882FG_REG_TEMP_HYST(1));
|
||||
}
|
||||
|
||||
if (data->type == f71862fg || data->type == f71882fg) {
|
||||
if (data->type == f71862fg || data->type == f71882fg ||
|
||||
data->type == f71889fg) {
|
||||
data->fan_beep = f71882fg_read8(data,
|
||||
F71882FG_REG_FAN_BEEP);
|
||||
data->temp_beep = f71882fg_read8(data,
|
||||
@ -977,15 +980,33 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev)
|
||||
data->temp_type[2] = (reg & 0x04) ? 2 : 4;
|
||||
data->temp_type[3] = (reg & 0x08) ? 2 : 4;
|
||||
}
|
||||
reg2 = f71882fg_read8(data, F71882FG_REG_PECI);
|
||||
if ((reg2 & 0x03) == 0x01)
|
||||
data->temp_type[1] = 6 /* PECI */;
|
||||
else if ((reg2 & 0x03) == 0x02)
|
||||
data->temp_type[1] = 5 /* AMDSI */;
|
||||
else if (data->type == f71862fg || data->type == f71882fg)
|
||||
data->temp_type[1] = (reg & 0x02) ? 2 : 4;
|
||||
else
|
||||
data->temp_type[1] = 2; /* Only supports BJT */
|
||||
/* Determine temp index 1 sensor type */
|
||||
if (data->type == f71889fg) {
|
||||
reg2 = f71882fg_read8(data, F71882FG_REG_START);
|
||||
switch ((reg2 & 0x60) >> 5) {
|
||||
case 0x00: /* BJT / Thermistor */
|
||||
data->temp_type[1] = (reg & 0x02) ? 2 : 4;
|
||||
break;
|
||||
case 0x01: /* AMDSI */
|
||||
data->temp_type[1] = 5;
|
||||
break;
|
||||
case 0x02: /* PECI */
|
||||
case 0x03: /* Ibex Peak ?? Report as PECI for now */
|
||||
data->temp_type[1] = 6;
|
||||
break;
|
||||
}
|
||||
} else {
|
||||
reg2 = f71882fg_read8(data, F71882FG_REG_PECI);
|
||||
if ((reg2 & 0x03) == 0x01)
|
||||
data->temp_type[1] = 6; /* PECI */
|
||||
else if ((reg2 & 0x03) == 0x02)
|
||||
data->temp_type[1] = 5; /* AMDSI */
|
||||
else if (data->type == f71862fg ||
|
||||
data->type == f71882fg)
|
||||
data->temp_type[1] = (reg & 0x02) ? 2 : 4;
|
||||
else /* f71858fg and f8000 only support BJT */
|
||||
data->temp_type[1] = 2;
|
||||
}
|
||||
|
||||
data->pwm_enable = f71882fg_read8(data,
|
||||
F71882FG_REG_PWM_ENABLE);
|
||||
@ -1062,7 +1083,7 @@ static struct f71882fg_data *f71882fg_update_device(struct device *dev)
|
||||
if (data->type == f8000)
|
||||
data->fan[3] = f71882fg_read16(data,
|
||||
F71882FG_REG_FAN(3));
|
||||
if (data->type == f71882fg)
|
||||
if (data->type == f71882fg || data->type == f71889fg)
|
||||
data->in_status = f71882fg_read8(data,
|
||||
F71882FG_REG_IN_STATUS);
|
||||
for (nr = 0; nr < nr_ins; nr++)
|
||||
@ -1780,7 +1801,11 @@ static ssize_t store_pwm_auto_point_temp(struct device *dev,
|
||||
int pwm = to_sensor_dev_attr_2(devattr)->index;
|
||||
int point = to_sensor_dev_attr_2(devattr)->nr;
|
||||
long val = simple_strtol(buf, NULL, 10) / 1000;
|
||||
val = SENSORS_LIMIT(val, 0, 255);
|
||||
|
||||
if (data->type == f71889fg)
|
||||
val = SENSORS_LIMIT(val, -128, 127);
|
||||
else
|
||||
val = SENSORS_LIMIT(val, 0, 127);
|
||||
|
||||
mutex_lock(&data->update_lock);
|
||||
f71882fg_write8(data, F71882FG_REG_POINT_TEMP(pwm, point), val);
|
||||
@ -1871,6 +1896,7 @@ static int __devinit f71882fg_probe(struct platform_device *pdev)
|
||||
ARRAY_SIZE(f71858fg_in_temp_attr));
|
||||
break;
|
||||
case f71882fg:
|
||||
case f71889fg:
|
||||
err = f71882fg_create_sysfs_files(pdev,
|
||||
fxxxx_in1_alarm_attr,
|
||||
ARRAY_SIZE(fxxxx_in1_alarm_attr));
|
||||
@ -1908,6 +1934,7 @@ static int __devinit f71882fg_probe(struct platform_device *pdev)
|
||||
err = (data->pwm_enable & 0x15) != 0x15;
|
||||
break;
|
||||
case f71882fg:
|
||||
case f71889fg:
|
||||
err = 0;
|
||||
break;
|
||||
case f8000:
|
||||
@ -1927,7 +1954,8 @@ static int __devinit f71882fg_probe(struct platform_device *pdev)
|
||||
if (err)
|
||||
goto exit_unregister_sysfs;
|
||||
|
||||
if (data->type == f71862fg || data->type == f71882fg) {
|
||||
if (data->type == f71862fg || data->type == f71882fg ||
|
||||
data->type == f71889fg) {
|
||||
err = f71882fg_create_sysfs_files(pdev,
|
||||
fxxxx_fan_beep_attr, nr_fans);
|
||||
if (err)
|
||||
@ -1950,6 +1978,22 @@ static int __devinit f71882fg_probe(struct platform_device *pdev)
|
||||
f8000_auto_pwm_attr,
|
||||
ARRAY_SIZE(f8000_auto_pwm_attr));
|
||||
break;
|
||||
case f71889fg:
|
||||
for (i = 0; i < nr_fans; i++) {
|
||||
data->pwm_auto_point_mapping[i] =
|
||||
f71882fg_read8(data,
|
||||
F71882FG_REG_POINT_MAPPING(i));
|
||||
if (data->pwm_auto_point_mapping[i] & 0x80)
|
||||
break;
|
||||
}
|
||||
if (i != nr_fans) {
|
||||
dev_warn(&pdev->dev,
|
||||
"Auto pwm controlled by raw digital "
|
||||
"data, disabling pwm auto_point "
|
||||
"sysfs attributes\n");
|
||||
break;
|
||||
}
|
||||
/* fall through */
|
||||
default: /* f71858fg / f71882fg */
|
||||
err = f71882fg_create_sysfs_files(pdev,
|
||||
&fxxxx_auto_pwm_attr[0][0],
|
||||
@ -2006,6 +2050,7 @@ static int f71882fg_remove(struct platform_device *pdev)
|
||||
ARRAY_SIZE(f71858fg_in_temp_attr));
|
||||
break;
|
||||
case f71882fg:
|
||||
case f71889fg:
|
||||
f71882fg_remove_sysfs_files(pdev,
|
||||
fxxxx_in1_alarm_attr,
|
||||
ARRAY_SIZE(fxxxx_in1_alarm_attr));
|
||||
@ -2027,7 +2072,8 @@ static int f71882fg_remove(struct platform_device *pdev)
|
||||
f71882fg_remove_sysfs_files(pdev, &fxxxx_fan_attr[0][0],
|
||||
ARRAY_SIZE(fxxxx_fan_attr[0]) * nr_fans);
|
||||
|
||||
if (data->type == f71862fg || data->type == f71882fg)
|
||||
if (data->type == f71862fg || data->type == f71882fg ||
|
||||
data->type == f71889fg)
|
||||
f71882fg_remove_sysfs_files(pdev,
|
||||
fxxxx_fan_beep_attr, nr_fans);
|
||||
|
||||
@ -2082,11 +2128,15 @@ static int __init f71882fg_find(int sioaddr, unsigned short *address,
|
||||
case SIO_F71882_ID:
|
||||
sio_data->type = f71882fg;
|
||||
break;
|
||||
case SIO_F71889_ID:
|
||||
sio_data->type = f71889fg;
|
||||
break;
|
||||
case SIO_F8000_ID:
|
||||
sio_data->type = f8000;
|
||||
break;
|
||||
default:
|
||||
printk(KERN_INFO DRVNAME ": Unsupported Fintek device\n");
|
||||
printk(KERN_INFO DRVNAME ": Unsupported Fintek device: %04x\n",
|
||||
(unsigned int)devid);
|
||||
goto exit;
|
||||
}
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user