mirror of
https://github.com/FEX-Emu/linux.git
synced 2024-12-14 21:01:29 +00:00
V4L/DVB (5558): Opera: use 7-bit i2c addresses
- the tuner i2c addr now without define (as wanted). - now 7 bit addr are used (the power_ctrl fkt ist ok so, because this is a raw write) - the addr >> 1 , addr << 1 is ok so, i think beause the read write is now taken from the last bit. - now i have no datasheet for the device, all taken from usb-logs Signed-off-by: Marco Gittler <g.marco@freenet.de> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This commit is contained in:
Marco Gittler
Mauro Carvalho Chehab
parent
12df2f54e5
commit
86534e5e8e
@ -32,13 +32,13 @@
|
||||
#define USB_VID_LITEON 0x04ca
|
||||
#define USB_VID_MEDION 0x1660
|
||||
#define USB_VID_MSI 0x0db0
|
||||
#define USB_VID_OPERA1 0x695c
|
||||
#define USB_VID_PINNACLE 0x2304
|
||||
#define USB_VID_VISIONPLUS 0x13d3
|
||||
#define USB_VID_TWINHAN 0x1822
|
||||
#define USB_VID_ULTIMA_ELECTRONIC 0x05d8
|
||||
#define USB_VID_UNIWILL 0x1584
|
||||
#define USB_VID_WIDEVIEW 0x14aa
|
||||
#define USB_VID_OPERA1 0x695c
|
||||
|
||||
/* Product IDs */
|
||||
#define USB_PID_ADSTECH_USB2_COLD 0xa333
|
||||
|
||||
@ -25,6 +25,11 @@
|
||||
#define REG_20_SYMBOLRATE_BYTE1 0x20
|
||||
#define REG_21_SYMBOLRATE_BYTE2 0x21
|
||||
|
||||
#define ADDR_B600_VOLTAGE_13V (0x02)
|
||||
#define ADDR_B601_VOLTAGE_18V (0x03)
|
||||
#define ADDR_B1A6_STREAM_CTRL (0x04)
|
||||
#define ADDR_B880_READ_REMOTE (0x05)
|
||||
|
||||
struct opera1_state {
|
||||
u32 last_key_pressed;
|
||||
};
|
||||
@ -70,7 +75,7 @@ static int opera1_xilinx_rw(struct usb_device *dev, u8 request, u16 value,
|
||||
/* I2C */
|
||||
|
||||
static int opera1_usb_i2c_msgxfer(struct dvb_usb_device *dev, u16 addr,
|
||||
u8 * buf, u16 len, int flag)
|
||||
u8 * buf, u16 len)
|
||||
{
|
||||
int ret = 0;
|
||||
u8 request;
|
||||
@ -83,16 +88,30 @@ static int opera1_usb_i2c_msgxfer(struct dvb_usb_device *dev, u16 addr,
|
||||
if (mutex_lock_interruptible(&dev->usb_mutex) < 0)
|
||||
return -EAGAIN;
|
||||
|
||||
request = (addr & 0xff00) >> 8;
|
||||
if (!request)
|
||||
request = 0xb1;
|
||||
value = (addr & 0xff);
|
||||
if (flag & OPERA_READ_MSG) {
|
||||
value |= 0x01;
|
||||
switch (addr>>1){
|
||||
case ADDR_B600_VOLTAGE_13V:
|
||||
request=0xb6;
|
||||
value=0x00;
|
||||
break;
|
||||
case ADDR_B601_VOLTAGE_18V:
|
||||
request=0xb6;
|
||||
value=0x01;
|
||||
break;
|
||||
case ADDR_B1A6_STREAM_CTRL:
|
||||
request=0xb1;
|
||||
value=0xa6;
|
||||
break;
|
||||
case ADDR_B880_READ_REMOTE:
|
||||
request=0xb8;
|
||||
value=0x80;
|
||||
break;
|
||||
default:
|
||||
request=0xb1;
|
||||
value=addr;
|
||||
}
|
||||
if (request == 0xa0)
|
||||
value = 0xe600;
|
||||
ret = opera1_xilinx_rw(dev->udev, request, value, buf, len, flag);
|
||||
ret = opera1_xilinx_rw(dev->udev, request,
|
||||
value, buf, len,
|
||||
addr&0x01?OPERA_READ_MSG:OPERA_WRITE_MSG);
|
||||
|
||||
mutex_unlock(&dev->usb_mutex);
|
||||
return ret;
|
||||
@ -111,13 +130,10 @@ static int opera1_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msg[],
|
||||
|
||||
for (i = 0; i < num; i++) {
|
||||
if ((tmp = opera1_usb_i2c_msgxfer(d,
|
||||
msg[i].addr,
|
||||
(msg[i].addr<<1)|(msg[i].flags&I2C_M_RD?0x01:0),
|
||||
msg[i].buf,
|
||||
msg[i].len,
|
||||
(msg[i].flags ==
|
||||
I2C_M_RD ?
|
||||
OPERA_READ_MSG :
|
||||
OPERA_WRITE_MSG))!= msg[i].len)) {
|
||||
msg[i].len
|
||||
)!= msg[i].len)) {
|
||||
break;
|
||||
}
|
||||
if (dvb_usb_opera1_debug & 0x10)
|
||||
@ -142,12 +158,12 @@ static int opera1_set_voltage(struct dvb_frontend *fe, fe_sec_voltage_t voltage)
|
||||
static u8 command_13v[1]={0x00};
|
||||
static u8 command_18v[1]={0x01};
|
||||
struct i2c_msg msg[] = {
|
||||
{.addr = 0xb600,.flags = 0,.buf = command_13v,.len = 1},
|
||||
{.addr = ADDR_B600_VOLTAGE_13V,.flags = 0,.buf = command_13v,.len = 1},
|
||||
};
|
||||
struct dvb_usb_adapter *udev_adap =
|
||||
(struct dvb_usb_adapter *)(fe->dvb->priv);
|
||||
if (voltage == SEC_VOLTAGE_18) {
|
||||
msg[0].addr = 0xb601;
|
||||
msg[0].addr = ADDR_B601_VOLTAGE_18V;
|
||||
msg[0].buf = command_18v;
|
||||
}
|
||||
i2c_transfer(&udev_adap->dev->i2c_adap, msg, 1);
|
||||
@ -220,7 +236,7 @@ static u8 opera1_inittab[] = {
|
||||
};
|
||||
|
||||
static struct stv0299_config opera1_stv0299_config = {
|
||||
.demod_address = 0xd0,
|
||||
.demod_address = 0xd0>>1,
|
||||
.min_delay_ms = 100,
|
||||
.mclk = 88000000UL,
|
||||
.invert = 1,
|
||||
@ -245,19 +261,21 @@ static int opera1_frontend_attach(struct dvb_usb_adapter *d)
|
||||
|
||||
static int opera1_tuner_attach(struct dvb_usb_adapter *adap)
|
||||
{
|
||||
adap->pll_addr = 0xc0;
|
||||
adap->pll_desc = &dvb_pll_opera1;
|
||||
adap->fe->ops.tuner_ops.set_params = dvb_usb_tuner_set_params_i2c;
|
||||
dvb_attach(
|
||||
dvb_pll_attach, adap->fe, 0xc0>>1,
|
||||
&adap->dev->i2c_adap, &dvb_pll_opera1
|
||||
);
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int opera1_power_ctrl(struct dvb_usb_device *d, int onoff)
|
||||
{
|
||||
int addr = onoff ? 0xb701 : 0xb700;
|
||||
u8 val = onoff ? 0x01 : 0x00;
|
||||
|
||||
if (dvb_usb_opera1_debug)
|
||||
info("power %s", onoff ? "on" : "off");
|
||||
return opera1_usb_i2c_msgxfer(d, addr, &val, 1, OPERA_WRITE_MSG);
|
||||
return opera1_xilinx_rw(d->udev, 0xb7, val,
|
||||
&val, 1, OPERA_WRITE_MSG);
|
||||
}
|
||||
|
||||
static int opera1_streaming_ctrl(struct dvb_usb_adapter *adap, int onoff)
|
||||
@ -265,7 +283,7 @@ static int opera1_streaming_ctrl(struct dvb_usb_adapter *adap, int onoff)
|
||||
static u8 buf_start[2] = { 0xff, 0x03 };
|
||||
static u8 buf_stop[2] = { 0xff, 0x00 };
|
||||
struct i2c_msg start_tuner[] = {
|
||||
{.addr = 0xb1a6,.buf = onoff ? buf_start : buf_stop,.len = 2},
|
||||
{.addr = ADDR_B1A6_STREAM_CTRL,.buf = onoff ? buf_start : buf_stop,.len = 2},
|
||||
};
|
||||
if (dvb_usb_opera1_debug)
|
||||
info("streaming %s", onoff ? "on" : "off");
|
||||
@ -278,7 +296,7 @@ static int opera1_pid_filter(struct dvb_usb_adapter *adap, int index, u16 pid,
|
||||
{
|
||||
u8 b_pid[3];
|
||||
struct i2c_msg msg[] = {
|
||||
{.addr = 0xb1a6,.buf = b_pid,.len = 3},
|
||||
{.addr = ADDR_B1A6_STREAM_CTRL,.buf = b_pid,.len = 3},
|
||||
};
|
||||
if (dvb_usb_opera1_debug)
|
||||
info("pidfilter index: %d pid: %d %s", index, pid,
|
||||
@ -295,7 +313,7 @@ static int opera1_pid_filter_control(struct dvb_usb_adapter *adap, int onoff)
|
||||
int u = 0x04;
|
||||
u8 b_pid[3];
|
||||
struct i2c_msg msg[] = {
|
||||
{.addr = 0xb1a6,.buf = b_pid,.len = 3},
|
||||
{.addr = ADDR_B1A6_STREAM_CTRL,.buf = b_pid,.len = 3},
|
||||
};
|
||||
if (dvb_usb_opera1_debug)
|
||||
info("%s hw-pidfilter", onoff ? "enable" : "disable");
|
||||
@ -345,7 +363,7 @@ static int opera1_rc_query(struct dvb_usb_device *dev, u32 * event, int *state)
|
||||
const u16 startmarker1 = 0x10ed;
|
||||
const u16 startmarker2 = 0x11ec;
|
||||
struct i2c_msg read_remote[] = {
|
||||
{.addr = 0xb880,.buf = rcbuffer,.flags = I2C_M_RD,.len = 32},
|
||||
{.addr = ADDR_B880_READ_REMOTE,.buf = rcbuffer,.flags = I2C_M_RD,.len = 32},
|
||||
};
|
||||
int i = 0;
|
||||
u32 send_key = 0;
|
||||
@ -467,7 +485,7 @@ static int opera1_xilinx_load_firmware(struct usb_device *dev,
|
||||
static struct dvb_usb_device_properties opera1_properties = {
|
||||
.caps = DVB_USB_IS_AN_I2C_ADAPTER,
|
||||
.usb_ctrl = CYPRESS_FX2,
|
||||
.firmware = "opera.fw",
|
||||
.firmware = "dvb-usb-opera-01.fw",
|
||||
.size_of_priv = sizeof(struct opera1_state),
|
||||
|
||||
.power_ctrl = opera1_power_ctrl,
|
||||
@ -522,7 +540,7 @@ static int opera1_probe(struct usb_interface *intf,
|
||||
if (udev->descriptor.idProduct == USB_PID_OPERA1_WARM &&
|
||||
udev->descriptor.idVendor == USB_VID_OPERA1 &&
|
||||
(d == NULL
|
||||
|| opera1_xilinx_load_firmware(udev, "opera1-fpga.fw") != 0)
|
||||
|| opera1_xilinx_load_firmware(udev, "dvb-usb-opera1-fpga.fw") != 0)
|
||||
) {
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
Loading…
Reference in New Issue
Block a user