myri*: Move the Myricom drivers

Move the Myricom drivers into drivers/net/ethernet/myricom/ and make
the necessary Kconfig and Makefile changes.

CC: Andrew Gallatin <gallatin@myri.com>
CC: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

MAINTAINERS

@@ -4335,7 +4335,7 @@ M:	Andrew Gallatin <gallatin@myri.com>
 L:	netdev@vger.kernel.org
 W:	http://www.myri.com/scs/download-Myri10GE.html
 S:	Supported
-F:	drivers/net/myri10ge/
+F:	drivers/net/ethernet/myricom/myri10ge/
 
 NATSEMI ETHERNET DRIVER (DP8381x)
 M:	Tim Hockin <thockin@hockin.org>

drivers/net/Kconfig

@@ -1519,32 +1519,6 @@ config VXGE_DEBUG_TRACE_ALL
 	  the vxge driver. By default only few debug trace statements are
 	  enabled.
 
-config MYRI10GE
-	tristate "Myricom Myri-10G Ethernet support"
-	depends on PCI && INET
-	select FW_LOADER
-	select CRC32
-	select INET_LRO
-	---help---
-	  This driver supports Myricom Myri-10G Dual Protocol interface in
-	  Ethernet mode. If the eeprom on your board is not recent enough,
-	  you will need a newer firmware image.
-	  You may get this image or more information, at:
-
-	  <http://www.myri.com/scs/download-Myri10GE.html>
-
-	  To compile this driver as a module, choose M here. The module
-	  will be called myri10ge.
-
-config MYRI10GE_DCA
-	bool "Direct Cache Access (DCA) Support"
-	default y
-	depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m)
-	---help---
-	  Say Y here if you want to use Direct Cache Access (DCA) in the
-	  driver.  DCA is a method for warming the CPU cache before data
-	  is used, with the intent of lessening the impact of cache misses.
-
 config PASEMI_MAC
 	tristate "PA Semi 1/10Gbit MAC"
 	depends on PPC_PASEMI && PCI && INET

drivers/net/Makefile

@@ -151,7 +151,6 @@ obj-$(CONFIG_R8169) += r8169.o
 obj-$(CONFIG_IBMVETH) += ibmveth.o
 obj-$(CONFIG_S2IO) += s2io.o
 obj-$(CONFIG_VXGE) += vxge/
-obj-$(CONFIG_MYRI10GE) += myri10ge/
 obj-$(CONFIG_PXA168_ETH) += pxa168_eth.o
 obj-$(CONFIG_BFIN_MAC) += bfin_mac.o
 obj-$(CONFIG_DM9000) += dm9000.o

drivers/net/ethernet/Kconfig

@@ -21,6 +21,7 @@ source "drivers/net/ethernet/emulex/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
 source "drivers/net/ethernet/i825xx/Kconfig"
 source "drivers/net/ethernet/mellanox/Kconfig"
+source "drivers/net/ethernet/myricom/Kconfig"
 source "drivers/net/ethernet/qlogic/Kconfig"
 source "drivers/net/ethernet/racal/Kconfig"
 source "drivers/net/ethernet/sfc/Kconfig"

drivers/net/ethernet/Makefile

@@ -12,6 +12,7 @@ obj-$(CONFIG_NET_VENDOR_EMULEX) += emulex/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
 obj-$(CONFIG_NET_VENDOR_I825XX) += i825xx/
 obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
+obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
 obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
 obj-$(CONFIG_NET_VENDOR_RACAL) += racal/
 obj-$(CONFIG_SFC) += sfc/

drivers/net/ethernet/myricom/Kconfig

@@ -0,0 +1,46 @@
+#
+# Myricom device configuration
+#
+
+config NET_VENDOR_MYRI
+	bool "Myricom devices"
+	depends on PCI && INET
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say
+	  Y and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Myricom cards. If you say Y, you will be asked for
+	  your specific card in the following questions.
+
+if NET_VENDOR_MYRI
+
+config MYRI10GE
+	tristate "Myricom Myri-10G Ethernet support"
+	depends on PCI && INET
+	select FW_LOADER
+	select CRC32
+	select INET_LRO
+	---help---
+	  This driver supports Myricom Myri-10G Dual Protocol interface in
+	  Ethernet mode. If the eeprom on your board is not recent enough,
+	  you will need a newer firmware image.
+	  You may get this image or more information, at:
+
+	  <http://www.myri.com/scs/download-Myri10GE.html>
+
+	  To compile this driver as a module, choose M here. The module
+	  will be called myri10ge.
+
+config MYRI10GE_DCA
+	bool "Direct Cache Access (DCA) Support"
+	default y
+	depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m)
+	---help---
+	  Say Y here if you want to use Direct Cache Access (DCA) in the
+	  driver.  DCA is a method for warming the CPU cache before data
+	  is used, with the intent of lessening the impact of cache misses.
+
+endif # NET_VENDOR_MYRI

drivers/net/ethernet/myricom/Makefile

@@ -0,0 +1,5 @@
+#
+# Makefile for the Myricom network device drivers.
+#
+
+obj-$(CONFIG_MYRI10GE) += myri10ge/