USB: NXP ISP1362 USB host driver

Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/usb/Makefile

@@ -16,6 +16,7 @@ obj-$(CONFIG_USB_UHCI_HCD)	+= host/
 obj-$(CONFIG_USB_FHCI_HCD)	+= host/
 obj-$(CONFIG_USB_XHCI_HCD)	+= host/
 obj-$(CONFIG_USB_SL811_HCD)	+= host/
+obj-$(CONFIG_USB_ISP1362_HCD)	+= host/
 obj-$(CONFIG_USB_U132_HCD)	+= host/
 obj-$(CONFIG_USB_R8A66597_HCD)	+= host/
 obj-$(CONFIG_USB_HWA_HCD)	+= host/

drivers/usb/host/Kconfig

@@ -159,6 +159,18 @@ config USB_ISP1760_HCD
 	  To compile this driver as a module, choose M here: the
 	  module will be called isp1760.
 
+config USB_ISP1362_HCD
+	tristate "ISP1362 HCD support"
+	depends on USB
+	default N
+	---help---
+	  Supports the Philips ISP1362 chip as a host controller
+
+	  This driver does not support isochronous transfers.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called isp1362-hcd.
+
 config USB_OHCI_HCD
 	tristate "OHCI HCD support"
 	depends on USB && USB_ARCH_HAS_OHCI

drivers/usb/host/Makefile

@@ -21,6 +21,7 @@ obj-$(CONFIG_PCI)		+= pci-quirks.o
 obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
 obj-$(CONFIG_USB_OXU210HP_HCD)	+= oxu210hp-hcd.o
 obj-$(CONFIG_USB_ISP116X_HCD)	+= isp116x-hcd.o
+obj-$(CONFIG_USB_ISP1362_HCD)	+= isp1362-hcd.o
 obj-$(CONFIG_USB_OHCI_HCD)	+= ohci-hcd.o
 obj-$(CONFIG_USB_UHCI_HCD)	+= uhci-hcd.o
 obj-$(CONFIG_USB_FHCI_HCD)	+= fhci.o

include/linux/usb/isp1362.h

@@ -0,0 +1,46 @@
+/*
+ * board initialization code should put one of these into dev->platform_data
+ * and place the isp1362 onto platform_bus.
+ */
+
+#ifndef __LINUX_USB_ISP1362_H__
+#define __LINUX_USB_ISP1362_H__
+
+struct isp1362_platform_data {
+	/* Enable internal pulldown resistors on downstream ports */
+	unsigned sel15Kres:1;
+	/* Clock cannot be stopped */
+	unsigned clknotstop:1;
+	/* On-chip overcurrent protection */
+	unsigned oc_enable:1;
+	/* INT output polarity */
+	unsigned int_act_high:1;
+	/* INT edge or level triggered */
+	unsigned int_edge_triggered:1;
+	/* DREQ output polarity */
+	unsigned dreq_act_high:1;
+	/* DACK input polarity */
+	unsigned dack_act_high:1;
+	/* chip can be resumed via H_WAKEUP pin */
+	unsigned remote_wakeup_connected:1;
+	/* Switch or not to switch (keep always powered) */
+	unsigned no_power_switching:1;
+	/* Ganged port power switching (0) or individual port power switching (1) */
+	unsigned power_switching_mode:1;
+	/* Given port_power, msec/2 after power on till power good */
+	u8 potpg;
+	/* Hardware reset set/clear */
+	void (*reset) (struct device *dev, int set);
+	/* Clock start/stop */
+	void (*clock) (struct device *dev, int start);
+	/* Inter-io delay (ns). The chip is picky about access timings; it
+	 * expects at least:
+	 * 110ns delay between consecutive accesses to DATA_REG,
+	 * 300ns delay between access to ADDR_REG and DATA_REG (registers)
+	 * 462ns delay between access to ADDR_REG and DATA_REG (buffer memory)
+	 * WE MUST NOT be activated during these intervals (even without CS!)
+	 */
+	void (*delay) (struct device *dev, unsigned int delay);
+};
+
+#endif