mirror of
https://github.com/FEX-Emu/linux.git
synced 2024-12-25 10:59:05 +00:00
[media] atmel-isi: update device tree bindings documentation
The original bindings documentation was incomplete (missing pinctrl-names, missing endpoint node properties) and the example was out of date. Add the missing information and tidy up the text. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This commit is contained in:
parent
a0c4164e0e
commit
e48f4eeac1
@ -1,51 +1,66 @@
|
||||
Atmel Image Sensor Interface (ISI) SoC Camera Subsystem
|
||||
----------------------------------------------
|
||||
Atmel Image Sensor Interface (ISI)
|
||||
----------------------------------
|
||||
|
||||
Required properties:
|
||||
- compatible: must be "atmel,at91sam9g45-isi"
|
||||
- reg: physical base address and length of the registers set for the device;
|
||||
- interrupts: should contain IRQ line for the ISI;
|
||||
- clocks: list of clock specifiers, corresponding to entries in
|
||||
the clock-names property;
|
||||
- clock-names: must contain "isi_clk", which is the isi peripherial clock.
|
||||
Required properties for ISI:
|
||||
- compatible: must be "atmel,at91sam9g45-isi".
|
||||
- reg: physical base address and length of the registers set for the device.
|
||||
- interrupts: should contain IRQ line for the ISI.
|
||||
- clocks: list of clock specifiers, corresponding to entries in the clock-names
|
||||
property; please refer to clock-bindings.txt.
|
||||
- clock-names: required elements: "isi_clk".
|
||||
- pinctrl-names, pinctrl-0: please refer to pinctrl-bindings.txt.
|
||||
|
||||
ISI supports a single port node with parallel bus. It should contain one
|
||||
ISI supports a single port node with parallel bus. It shall contain one
|
||||
'port' child node with child 'endpoint' node. Please refer to the bindings
|
||||
defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
|
||||
|
||||
Endpoint node properties
|
||||
------------------------
|
||||
|
||||
- bus-width: <8> or <10> (mandatory)
|
||||
- hsync-active (default: active high)
|
||||
- vsync-active (default: active high)
|
||||
- pclk-sample (default: sample on falling edge)
|
||||
- remote-endpoint: A phandle to the bus receiver's endpoint node (mandatory).
|
||||
|
||||
Example:
|
||||
isi: isi@f0034000 {
|
||||
compatible = "atmel,at91sam9g45-isi";
|
||||
reg = <0xf0034000 0x4000>;
|
||||
interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>;
|
||||
|
||||
clocks = <&isi_clk>;
|
||||
clock-names = "isi_clk";
|
||||
isi: isi@f0034000 {
|
||||
compatible = "atmel,at91sam9g45-isi";
|
||||
reg = <0xf0034000 0x4000>;
|
||||
interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_isi_data_0_7>;
|
||||
clocks = <&isi_clk>;
|
||||
clock-names = "isi_clk";
|
||||
port {
|
||||
isi_0: endpoint {
|
||||
remote-endpoint = <&ov2640_0>;
|
||||
bus-width = <8>;
|
||||
vsync-active = <1>;
|
||||
hsync-active = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
i2c1: i2c@f0018000 {
|
||||
ov2640: camera@30 {
|
||||
compatible = "ovti,ov2640";
|
||||
reg = <0x30>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_isi>;
|
||||
pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
|
||||
resetb-gpios = <&pioE 11 GPIO_ACTIVE_LOW>;
|
||||
pwdn-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
|
||||
clocks = <&pck0>;
|
||||
clock-names = "xvclk";
|
||||
assigned-clocks = <&pck0>;
|
||||
assigned-clock-rates = <25000000>;
|
||||
|
||||
port {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
isi_0: endpoint {
|
||||
remote-endpoint = <&ov2640_0>;
|
||||
ov2640_0: endpoint {
|
||||
remote-endpoint = <&isi_0>;
|
||||
bus-width = <8>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
i2c1: i2c@f0018000 {
|
||||
ov2640: camera@0x30 {
|
||||
compatible = "ovti,ov2640";
|
||||
reg = <0x30>;
|
||||
|
||||
port {
|
||||
ov2640_0: endpoint {
|
||||
remote-endpoint = <&isi_0>;
|
||||
bus-width = <8>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
Loading…
Reference in New Issue
Block a user