Skip ISA ioresource alignment on some systems
To conserve limited PCI i/o resource on some IBM multi-node systems, the
BIOS allocates (via _CRS) and expects the kernel to use addresses in
ranges currently excluded by pcibios_align_resource() [i386/pci/i386.c].
This change allows the kernel to use the currently excluded address
ranges on the IBM x3800, x3850, and x3950.
Signed-off-by: Gary Hade <gary.hade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove transparent bridge sizing.
Due to code in pci_read_bridge_bases() [drivers/pci/probe.c] the child
bus of a transparent bridge already has access to the parent bus
resources so transparent bridge sizing appears unnecessary. The bridge
sizing includes alignment and granularity adjustments that can cause
significantly more memory to be reserved from the parant bus than
required by devices on the child bus and allotted by _CRS.
Signed-off-by: Gary Hade <gary.hade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a /proc/bus/pci file is written to, the size of that PCI device's
configuration space must be written to the inode. Otherwise, it is
possible for the file to specify a size of 0 on stat if a task is holding
the same file open.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On pci_proc_attach_device(), the size of the PCI configuration space is
stored in the proc_dir_entry as the size of the file. Thus, the procfs
interface to PCI devices should use it instead of the device directly.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For cases in which CONFIG_PCIEAER=y (such as distro kernels), allow users
to disable PCIE Advanced Error Reporting by using "pci=noaer" on the
kernel command line.
This can be used to work around hardware or (kernel) software problems.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I got the following error on MIPS Cobalt.
PCI: Unable to reserve I/O region #1:8@f00001f0 for device 0000:00:09.1
pata_via 0000:00:09.1: failed to request/iomap BARs for port 0 (errno=-16)
PCI: Unable to reserve I/O region #3:8@f0000170 for device 0000:00:09.1
pata_via 0000:00:09.1: failed to request/iomap BARs for port 1 (errno=-16)
pata_via 0000:00:09.1: no available native port
The legacy mode IDE resources set the following order.
pci_setup_device()
Legacy mode ATA controllers have fixed addresses.
IDE resources: 0x1F0-0x1F7, 0x3F6, 0x170-0x177, 0x376
|
V
pcibios_fixup_bus()
MIPS Cobalt PCI bus regions have the -0x10000000 offset from PCI resources.
pcibios_fixup_bus() fix PCI bus regions.
0x1F0 - 0x10000000 = 0xF00001F0
|
V
ata_pci_init_one()
PCI: Unable to reserve I/O region #1:8@f00001f0 for device 0000:00:09.1
In some architectures, PCI bus regions have the offset from PCI resources.
For this reason, pci_setup_device() should set PCI bus regions to
dev->resource[].
[akpm@linux-foundation.org: use struct initialiser]
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While reading the MSI code trying to find a reason why MSI wouldn't
work for devices that have a 32-bit MSI address capability, I noticed
that read_msi_msg() seems to read the message data from the wrong
offset in this case.
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code for dynamically assigning new ids to PCI drivers,
store_new_id(), calls list_add_tail() with the list head and new node
arguments in reversed order.
The result is that every new id written essentially overwrites the
previous list of ids.
Caught with the help of Rusty's "horribly bad" list_node patch:
http://lkml.org/lkml/2007/6/10/10
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the "MSI K8T Neo2-FIR" board the BIOS disables the onboard
soundcard, if a second PCI soundcard is present.
This patch sets the korrect register bit to enable the onboard sound.
Removed old code in /drivers/pci/quirks.c that only checks for the
PCI-ID and fires on any Board with VIA 8237.
New code in /arch/i386/pci/fixup.c checks the DMI-tables and only runs
on the specific board.
Signed-off-by: Johannes Goecke <goecke@upb.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While PCI_CLASS_REVISION and PCI_REVISION_ID are identical, the
code here discards the revision content and is only interested in
the class number.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Krosten Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert ibmphp to new kthread api
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replacing n & (n - 1) for power of 2 check by is_power_of_2(n)
Signed-off-by: vignesh babu <vignesh.babu@wipro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanups for pciehp_hpc.c. The 80 column rules, removing
unnecessary lines, and so on.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes DBG_ENTER_ROUTIN, DBG_LEAVE_ROUTINE and related
code, which seem no longer needed.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the PCI firmware spec (3.0), the OS must claim control
over the PCI Express Capability bits in addition to the PCI Express
Native Hot Plug feature when executing _OSC.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When removing a device with a bridge on it, only read the
bridge control register if the adapter is actually present.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove unnecessary CONFIG_HOTPLUG_PCI_PCIE_EVENT_MODE.
The CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE option is not needed
because polling mechanism can be enabled through 'pciehp_poll_mode'
module option.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linas reported me that some machines were crashing at boot in
quirk_e100_interrupt. It appears that this quirk is doing an ioremap
directly on a PCI BAR value, which isn't legal and will cause all sorts
of bad things to happen on architectures where PCI BARs don't directly
match processor bus addresses.
This fixes it by using the proper PCI resources instead which is possible
since the quirk has been moved by a previous commit to happen late enough
for that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCI quirk to unhide SMBus on Compaq Deskpro EP 401963-001 (PCA# 010174) motherboard.
Signed-off-by: Greg White <gw.kernel@tnode.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On MIPS with PCI && !HOTPLUG, I'm currently getting the following modpost
warning:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x1ce128): Section mismatch: reference to .init.text:pci_read_bridge_bases (between 'pcibios_fixup_bus' and 'pcibios_enable_device')
On MIPS I have the call chains pci_scan_child_bus -> pcibios_fixup_bus ->
pci_read_bridge_bases. pci_scan_child_bus can't be __devinit because it
it is an exported symbol, thus pcibios_fixup_bus and pci_read_bridge_bases
can't be either.
For some reason I don't see this issue on x86; I blame compiler differences.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add missing \n to error in ibm_find_acpi_device.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Adrian Bunk <trivial@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Schedule /proc/acpi/event for removal in 6 months.
Re-name acpi_bus_generate_event() to acpi_bus_generate_proc_event()
to make sure there is no confusion that it is for /proc/acpi/event only.
Add CONFIG_ACPI_PROC_EVENT to allow removal of /proc/acpi/event.
There is no functional change if CONFIG_ACPI_PROC_EVENT=y
Signed-off-by: Len Brown <len.brown@intel.com>
The previous events patch added a netlink event for every
user of the legacy /proc/acpi/event interface.
However, some users of /proc/acpi/event are really input events,
and they already report their events via the input layer.
Introduce a new interface, acpi_bus_generate_netlink_event(),
which is explicitly called by devices that want to repoprt
events via netlink. This allows the input-like events
to opt-out of generating netlink events. In summary:
events that are sent via netlink:
ac/battery/sbs
thermal
processor
thinkpad_acpi dock/bay
events that are sent via input layer:
button
video hotkey
thinkpad_acpi hotkey
asus_acpi/asus-laptop hotkey
sonypi/sonylaptop
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The k8t_sound_hostbridge PCI quick fires on my motherboard (Jetway
K8M8MS) while it shouldn't: the on-board sound chip is not disabled
and is working just fine. Looking at the code, I see that we are
running the quirk for two distinct register values (0x88 and 0xc8)
and then clear bit 6 (0x40). However value 0x88 already has bit 6
cleared so this is a no-op. This is what happens on my board. Thus I
believe that the quirk should only be run for register value 0xc8.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RS690 can't do MSI like its predecessors. Disable MSI on RS690.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Henry Su <henry.su@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adrian Bunk wrote:
> Alois Nešpor wrote
>> PCI: Bus #0b (-#0e) is hidden behind transparent bridge #0a (-#0b) (try 'pci=assign-busses')
>> Please report the result to linux-kernel to fix this permanently"
>>
>> dmesg:
>> "Yenta: Raising subordinate bus# of parent bus (#0a) from #0b to #0e"
>> without pci=assign-busses and nothing with pci=assign-busses.
>
> Bernhard?
Ok, lets kill the message. As Alois Nešpor also saw, that's fixed up by Yenta,
so PCI does not have to warn about it. PCI could still warn about it if
is_cardbus is 0 in that instance of pci_scan_bridge(), but so far I have
not seen a report where this would have been the case so I think we can
spare the kernel of that check (removes ~300 lines of asm) unless debugging
is done.
History: The whole check was added in the days before we had the fixup
for this in Yenta and pci=assign-busses was the only way to get CardBus
cards detected on many (not all) of the machines which give this warning.
In theory, there could be cases when this warning would be triggered and
it's not cardbus, then the warning should still apply, but I think this
should only be the case when working on a completely broken PCI setup,
but one may have already enabled the debug code in drivers/pci and the
patched check would then trigger.
I do not sign this off yet because it's completely untested so far, but
everyone is free to test it (with the #ifdef DEBUG replaced by #if 1 and
pr_debug( changed to printk(.
We may also dump the whole check (remove everything within the #ifdef from
the source) if that's perferred.
On Alois Nešpor's machine this would then (only when debugging) this message:
"PCI: Bus #0b (-#0e) is partially hidden behind transparent bridge #0a (-#0b)"
"partially" should be in the message on his machine because #0b of #0b-#0e
is reachable behind #0a-#0b, but not #0c-#0e.
But that differentiation is now moot anyway because the fixup in Yenta takes
care of it as far as I could see so far, which means that unless somebody
is debugging a totally broken PCI setup, this message is not needed anymore,
not even for debugging PCI.
Ok, here the patch with the following changes:
* Refined to say that the bus is only partially hidden when the parent
bus numbers are not totally way off (outside of) the child bus range
* remove the reference to pci=assign-busses and the plea to report it
We could add a pure source code-only comment to keep a reference to
pci=assign-busses the in case when this is triggered by someone who
is debugging the cause of this message and looking the way to solve it.
From: Bernhard Kaindl <bk@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remove stale BKL use from drivers/pci/hotplug/cpqphp_ctrl.c.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
quirk_e100_interrupts() is called after PCI controller is initialized
and before PCI bus enumeration is performed. On some powerpc platforms
which modify PCI controller configuration and set different MEM and IO
windows than those set by firmware quirk_e100_interrupt() is causing
kernel panic as it tries to read from device BAR0 offets which at this
time points to a invalid PCI window (set by firmware).
This patch delays the quirk_100_interrupt() to pci_fixup_final phase,
which happens after bus enumeration and before PCI enable and
device driver initialization.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need pci_bus_find_capability() in some arch/powerpc code so move
the prototype into a header accessible to it.
Also kill the duplicate prototype for pci_bus_alloc_resource().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix undocumented function parameters in PCI and drivers/base.
Warning(linux-2.6.23-rc1//drivers/pci/pci.c:1526): No description found for parameter 'rq'
Warning(linux-2.6.23-rc1//drivers/base/firmware_class.c:245): No description found for parameter 'bin_attr'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restore the 2.6.22 CONFIG_ACPI_SLEEP build option, but now shadowing the
new CONFIG_PM_SLEEP option.
Signed-off-by: Len Brown <len.brown@intel.com>
[ Modified to work with the PM config setup changes. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: Kconfig: remove CONFIG_ACPI_SLEEP from source
ACPI: quiet ACPI Exceptions due to no _PTC or _TSS
ACPI: Remove references to ACPI_STATE_S2 from acpi_pm_enter
ACPI: Kconfig: always enable CONFIG_ACPI_SLEEP on X86
ACPI: Kconfig: fold /proc/acpi/sleep under CONFIG_ACPI_PROCFS
ACPI: Kconfig: CONFIG_ACPI_PROCFS now defaults to N
ACPI: autoload modules - Create __mod_acpi_device_table symbol for all ACPI drivers
ACPI: autoload modules - Create ACPI alias interface
ACPI: autoload modules - ACPICA modifications
ACPI: asus-laptop: Fix failure exits
ACPI: fix oops due to typo in new throttling code
ACPI: ignore _PSx method for hotplugable PCI devices
ACPI: Use ACPI methods to select PCI device suspend state
ACPI, PNP: hook ACPI D-state to PNP suspend/resume
ACPI: Add acpi_pm_device_sleep_state helper routine
ACPI: Implement the set_target() callback from pm_ops
Some odd ACPI implementations choke if certain controller is disabled
when ACPI suspend is invoked but we still need to make sure the PCI
device is enabled during resume. Simply using pci_enable_device()
unbalances device enable count. Export __pci_reenable_device().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the ACPI device has _EJ0, ignore the device.
_PSx will set power for the slot,
and the hotplug driver will take care of _PSx.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
applied after Rafel's 'PM: Update global suspend and hibernation
operations framework' patch set
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (209 commits)
[POWERPC] Create add_rtc() function to enable the RTC CMOS driver
[POWERPC] Add H_ILLAN_ATTRIBUTES hcall number
[POWERPC] xilinxfb: Parameterize xilinxfb platform device registration
[POWERPC] Oprofile support for Power 5++
[POWERPC] Enable arbitary speed tty ioctls and split input/output speed
[POWERPC] Make drivers/char/hvc_console.c:khvcd() static
[POWERPC] Remove dead code for preventing pread() and pwrite() calls
[POWERPC] Remove unnecessary #undef printk from prom.c
[POWERPC] Fix typo in Ebony default DTS
[POWERPC] Check for NULL ppc_md.init_IRQ() before calling
[POWERPC] Remove extra return statement
[POWERPC] pasemi: Don't auto-select CONFIG_EMBEDDED
[POWERPC] pasemi: Rename platform
[POWERPC] arch/powerpc/kernel/sysfs.c: Move NUMA exports
[POWERPC] Add __read_mostly support for powerpc
[POWERPC] Modify sched_clock() to make CONFIG_PRINTK_TIME more sane
[POWERPC] Create a dummy zImage if no valid platform has been selected
[POWERPC] PS3: Bootwrapper support.
[POWERPC] powermac i2c: Use mutex
[POWERPC] Schedule removal of arch/ppc
...
Fixed up conflicts manually in:
Documentation/feature-removal-schedule.txt
arch/powerpc/kernel/pci_32.c
arch/powerpc/kernel/pci_64.c
include/asm-powerpc/pci.h
and asked the powerpc people to double-check the result..