When registering the Tegra power partitions with the generic PM domain
framework, the current state of the each partition is checked and used
as the default state for the partition. However, the state of each reset
associated with the partition is not initialised and so it is possible
that the state of the resets are not in the expected state. For example,
if a partition is on, then the resets should be de-asserted and if the
partition is off, the resets should be asserted.
There have been cases where the bootloader has powered on a partition
and only de-asserted some of the resets to some of the devices in the
partition. This can cause accesses to these devices to hang the system
when the kernel boots and attempts to probe these devices.
Ideally, the driver for the device should ensure the reset has been
de-asserted when probing, but the resets cannot be shared between the
PMC driver (that needs to de-assert/assert the reset when turning the
partition on or off) and another driver because we cannot ensure the
reset is in the correct state.
To ensure the resets are in the correct state, when using the generic
PM domain framework, put each reset associated with the partition in
the correct state (based upon the partition's current state) when
obtaining the resets for a partition.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use register definitions for the main SoC reset operation instead of
hard-coding magic values. Note that the PMC_RST_STATUS register isn't
actually accessed, but since it is mentioned in a comment the
definitions are added for completeness.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons. For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to
get done.
Finally, reset controller handling as always gets merged through here
as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x+iD
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
Adds generic PM domain support to the PMC driver where the PM domains
are populated from device-tree and the PM domain consumer devices are
bound to their relevant PM domains via device-tree as well.
Update the tegra_powergate_sequence_power_up() API so that internally
it calls the same tegra_powergate_xxx functions that are used by the
Tegra generic PM domain code for consistency.
To ensure that the Tegra power domains (a.k.a. powergates) cannot be
controlled via both the legacy tegra_powergate_xxx functions as well
as the generic PM domain framework, add a bit map for available
powergates that can be controlled via the legacy powergate functions.
Move the majority of the tegra_powergate_remove_clamping() function
to a sub-function, so that this can be used by both the legacy and
generic power domain code.
This is based upon work by Thierry Reding <treding@nvidia.com>
and Vince Hsu <vinceh@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These two are both ARMv7 SoCs. They need not explicitly select
ARM_L1_CACHE_SHIFT_6 because it is enabled along with CPU_V7.
Refer to commit a092f2b153 ("ARM: 7291/1: cache: assume 64-byte L1
cachelines for ARMv7 CPUs").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently, the function tegra_powergate_set() simply sets the desired
powergate state but does not wait for the state to change. In most cases
we should wait for the state to change before proceeding. Currently,
there is a case for Tegra114 and Tegra124 devices where we do not wait
when starting the secondary CPU as this is not necessary. However, this
is only done at boot time and so waiting here will only have a small
impact on boot time. Therefore, update tegra_powergate_set() to wait
when setting the powergate.
By adding this feature, we can also eliminate the polling loop from
tegra30_boot_secondary().
A function has been added for checking the status of the powergate and
so update the tegra_powergate_is_powered() to use this macro as well.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For Tegra124 and Tegra210, the GPU partition cannot be toggled on and
off via the APBDEV_PMC_PWRGATE_TOGGLE_0 register. For these devices, the
partition is simply powered up and down via an external regulator.
For these devices, there is a separate register for controlling the
signal clamping of the partition and this is described in the PMC SoC
data by the "has_gpu_clamp" variable. Use this variable to determine if
the GPU partition can be controlled via the APBDEV_PMC_PWRGATE_TOGGLE_0
register and ensure that no one can incorrectly try to toggle the GPU
partition via the APBDEV_PMC_PWRGATE_TOGGLE_0 register.
Furthermore, we cannot use the APBDEV_PMC_PWRGATE_STATUS_0 register to
determine if the GPU partition is powered for Tegra124 and Tegra210.
However, if the GPU partition is powered, then the signal clamp for the
GPU partition should be removed and so use bit 0 of the
APBDEV_PMC_GPU_RG_CNTRL_0 register to determine if the clamp has been
removed (bit[0] = 0) and the GPU partition is powered.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The function tegra_powergate_is_powered() verifies that the partition
being queried is valid and so there is no need to check this before
calling tegra_powergate_is_powered() in powergate_show(). So remove this
extra check.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra power partitions are referenced by numerical IDs which are the
same values programmed into the PMC registers for controlling the
partition. For a given device, the valid partition IDs may not be
contiguous and so simply checking that an ID is not greater than the
maximum ID supported may not mean it is valid. Fix this by checking if
the powergate is defined in the list of powergates for the Tegra SoC.
Add a helper function for checking valid powergates and use where we
need to verify if the powergate ID is valid or not.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In tegra_powergate_set() the state of the powergates is read and OR'ed
with the bit for the powergate of interest. This unsigned 32-bit value
is then compared with a boolean value to test if the powergate is
already in the desired state. When turning on a powergate, apart from
the powergate that is represented by bit 0, this test will always
return false and so we may attempt to turn on the powergate when it is
already on.
After OR'ing the bit for the powergate, check if the result is not equal
to zero before comparing with the boolean value. Add a helper function
to return the current state of a powergate and use this in both
tegra_powergate_set() and tegra_powergate_is_powered() where we check
the powergate status.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra powergate and rail IDs are always positive values and so change
the type to be unsigned and remove the tests to see if the ID is less
than zero. Update the Tegra DC powergate type to be an unsigned as well.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PMC base address pointer is initialised during early boot so that
early platform code may used the PMC public functions. During the probe
of the PMC driver the base address pointer is mapped again and the initial
mapping is freed. This exposes a window where a device accessing the PMC
registers via one of the public functions, could race with the updating
of the pointer and lead to a invalid access. Furthermore, the only
protection between multiple devices attempting to access the PMC registers
is when setting the powergate state to on or off. None of the other public
functions that access the PMC registers are protected.
Use the existing mutex to protect paths that may race with regard to
accessing the PMC registers.
Note that functions tegra_io_rail_prepare()/poll() either return a
negative value on failure or zero on success. Therefore, it is not
necessary to check if the return value is less than zero and so only
test that the return value is not zero to test for failure. This
simplifies the error handling with the mutex locking in place.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
During early initialisation, the PMC registers are mapped and the PMC SoC
data is populated in the PMC data structure. This allows other drivers
access the PMC register space, via the public Tegra PMC APIs, prior to
probing the PMC device.
When the PMC device is probed, the PMC registers are mapped again and if
successful the initial mapping is freed. If the probing of the PMC device
fails after the registers are remapped, then the registers will be
unmapped and hence the pointer to the PMC registers will be invalid. This
could lead to a potential crash, because once the PMC SoC data pointer is
populated, the driver assumes that the PMC register mapping is also valid
and a user calling any of the public Tegra PMC APIs could trigger an
exception because these APIs don't check that the mapping is still valid.
Fix this by updating the mapping and freeing the original mapping only if
probing the PMC device is successful.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 does not have an L2 power partition and the L2 cache is part of
the cluster 0 non-CPU (CONC) partition. Remove the L2 as a valid
partition for Tegra124. The TRM also shows that there is no L2 partition
for Tegra124.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The power partitions L2, HEG, CELP and C1NC do not exist on Tegra210 but
were incorrectly documented in the TRM. These will be removed from the
TRM and so also remove their definitions.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The debugfs entry for the PMC device will not be removed if the probe of
the device fails to register the restart handler. This leaves behind the
dangling debugfs entry with no driver backing it. Remove the entry to
avoid this.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sparse reports the following warning for tegra_pmc_init_tsense_reset():
drivers/soc/tegra/pmc.c:741:6: warning: symbol 'tegra_pmc_init_tsense_reset' was not declared. Should it be static?
This function is only used internally by the PMC driver and so fix this
by making it static.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some members of the tegra_pmc structure are missing from the kernel-doc
comment for this structure. Add the missing members.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For historic reasons, the tegra platform selects USB_ULPI from architecture
code, but that hasn't really made sense for a long time, as the only
user of that code is the Tegra EHCI driver that has its own Kconfig
symbol.
This removes the 'select' statements from mach-tegra and drivers/soc/tegra
and adds them with the device driver that actually needs them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Also known as Tegra X1, the Tegra210 has four Cortex-A57 cores paired
with four Cortex-A53 cores in a switched configuration. It features a
GPU using the Maxwell architecture with support for DX11, SM4, OpenGL
4.5, OpenGL ES 3.1 and providing 256 CUDA cores. It supports hardware
accelerated en- and decoding of various video standards including
H.265, H.264 and VP8 at 4K resolutions and up to 60 fps.
Besides the multimedia features it also comes with a variety of I/O
controllers such as GPIO, I2C, SPI, SDHCI, PCIe, SATA and XHCI, to
name only a few.
Add a Kconfig option for Tegra210 to allow SoC-specific support to be
enabled for this new generation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move per-SoC generation Kconfig symbols to drivers/soc/tegra/Kconfig to
gather them all in a single place. This directory is a natural location
for these options since it already contains the drivers that are shared
across 32-bit and 64-bit ARM architectures.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver requests the pclk clock at probe time already and stores its
reference to it in struct tegra_pmc, so there is no need to look it up
everytime it is needed. Use the existing reference instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Kbuild descends into drivers/soc/tegra/ only when CONFIG_ARCH_TEGRA
is enabled. (see drivers/soc/Makefile)
$(CONFIG_ARCH_TEGRA) in drivers/soc/tegra/Makefile always evaluates
to 'y'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The offset of the first spare bit register on Tegra210 is 0x380, but
account for the fixed offset of 0x100 in the fuse accessor.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The offset of the first spare bit register on Tegra124 is 0x300, but
account for the fixed offset of 0x100 in the fuse accessor.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The offset of the first spare bit register on Tegra114 is 0x280, but
account for the fixed offset of 0x100 in the fuse accessor.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There's a mixture of core_* and soc_* prefixes for variables storing
information related to the VDD_CORE rail. Choose one (soc_*) and use it
more consistently.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Unifying the drivers makes it easier to restrict the legacy probing
paths to 32-bit ARM. This in turn will come in handy as support for
new 64-bit ARM SoCs is added.
Signed-off-by: Thierry Reding <treding@nvidia.com>
For backwards-compatibility with old device trees, if no APBMISC node
exists this driver hard-codes the I/O memory region. All 64-bit ARM
device tree files are recent enough that they can be required to have
this node, and therefore the legacy code path is not required.
Based on work done by Paul Walmsley <pwalmsley@nvidia.com>.
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 uses a power management controller that is compatible with
earlier SoC generations but adds a couple of power partitions for new
hardware blocks.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For backwards-compatibility with old device trees, if no PMC node exists
this driver hard-codes the I/O memory region. All 64-bit ARM device tree
files are recent enough that they can be required to have this node, and
therefore the legacy code path is not required on 64-bit ARM.
Based on work done by Paul Walmsley <pwalmsley@nvidia.com>.
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make sure to only drop the reference to the OF node after it's been
successfully obtained.
Fixes: 3568df3d31 ("soc: tegra: Add thermal reset (thermtrip) support to PMC")
Cc: <stable@vger.kernel.org> # v4.0+
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WLBw
-----END PGP SIGNATURE-----
Merge tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_platform_driver replacement from Paul Gortmaker:
"Replace module_platform_driver with builtin_platform driver in non
modules.
We see an increasing number of non-modular drivers using
modular_driver() type register functions. There are several downsides
to letting this continue unchecked:
- The code can appear modular to a reader of the code, and they won't
know if the code really is modular without checking the Makefile
and Kconfig to see if compilation is governed by a bool or
tristate.
- Coders of drivers may be tempted to code up an __exit function that
is never used, just in order to satisfy the required three args of
the modular registration function.
- Non-modular code ends up including the <module.h> which increases
CPP overhead that they don't need.
- It hinders us from performing better separation of the module init
code and the generic init code.
So here we introduce similar macros for builtin drivers. Then we
convert builtin drivers (controlled by a bool Kconfig) by making the
following type of mapping:
module_platform_driver() ---> builtin_platform_driver()
module_platform_driver_probe() ---> builtin_platform_driver_probe().
The set of drivers that are converted here are just the ones that
showed up as relying on an implicit include of <module.h> during a
pending header cleanup. So we convert them here vs adding an include
of <module.h> to non-modular code to avoid compile fails. Additonal
conversions can be done asynchronously at any time.
Once again, an unused module_exit function that is removed here
appears in the diffstat as an outlier wrt all the other changes"
* tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver
drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver
drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver
drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver
drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver
drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver
platform_device: better support builtin boilerplate avoidance
Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses
Conflicts:
arch/arm64/boot/dts/arm/juno-motherboard.dtsi
Trivial add/add conflict with our dt branch.
Resolution: take both sides.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=02Gm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Kevin Hilman:
"Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: soc: sunxi: Introduce SoC driver to map SRAMs
arm-cci: Add aliases for PMU events
arm-cci: Add CCI-500 PMU support
arm-cci: Sanitise CCI400 PMU driver specific code
arm-cci: Abstract handling for CCI events
arm-cci: Abstract out the PMU counter details
arm-cci: Cleanup PMU driver code
arm-cci: Do not enable CCI-400 PMU by default
firmware: qcom: scm: Add HDCP Support
ARM: berlin: add an ADC node for the BG2Q
ARM: berlin: remove useless chip and system ctrl compatibles
clk: berlin: drop direct of_iomap of nodes reg property
ARM: berlin: move BG2Q clock node
ARM: berlin: move BG2CD clock node
ARM: berlin: move BG2 clock node
clk: berlin: prepare simple-mfd conversion
pinctrl: berlin: drop SoC stub provided regmap
ARM: berlin: move pinctrl to simple-mfd nodes
pinctrl: berlin: prepare to use regmap provided by syscon
reset: berlin: drop arch_initcall initialization
...
This file depends on Kconfig ARCH_TEGRA which is a bool, so
we use the appropriate registration function, which avoids us
relying on an implicit inclusion of <module.h> which we are
doing currently.
While this currently works, we really don't want to be including
the module.h header in non-modular code, which we'd be forced
to do, pending some upcoming code relocation from init.h into
module.h. So we fix it now by using the non-modular equivalent.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The pmc driver was previously exporting tegra_pmc_restart, which was
assigned to machine_desc.init_machine, taking precedence over the
restart handlers registered through register_restart_handler().
Signed-off-by: David Riley <davidriley@chromium.org>
[tomeu.vizoso@collabora.com: Rebased]
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
[treding@nvidia.com: minor cleanups]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Needed for the EMC and MC drivers to know what timings from the DT to
use.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The return type of the wait_for_completion_timeout() function is not int
but unsigned long. An appropriately named unsigned long is added and the
assignment fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds a device tree controlled option to enable PMC-based
thermal reset in overheating situations. Thermtrip is supported on
Tegra30, Tegra114 and Tegra124. The thermal reset only works when
the thermal sensors are calibrated, so a soctherm driver is also
required.
The thermtrip event is triggered by the soctherm block, and all
soctherm sensors default to showing a temperature of zero Celsius
before they are initialized. Because of this, it is safe to initialize
thermtrip and soctherm in any order.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra132 uses the same GPU as Tegra124 and therefore requires the same
method to remove clamps. However Tegra132 has a separate chip ID, so in
order to avoid having to extend the list of chip IDs for the special
case, add a feature flag to the SoC data.
Reviewed-by: Paul Walmsley <pwalmsley@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra132 is very similar to Tegra124 from a peripheral point of view and
uses the same fuse controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra SoCs with 64-bit ARM support don't currently support deep CPU
low-power states in mainline Linux. When this support is added in the
future, it will probably look rather different from the existing
32-bit ARM support, since the ARM64 maintainers' strong preference is
to use PSCI to implement it.
So, for the time being, prevent the CPU suspend-related code and data
in the Tegra PMC driver from compiling on ARM64.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
Some Tegra drivers might be compiled as kernel modules, and they need the
fuse information for initialization. One example is the GK20A Nouveau
driver. It needs the GPU speedo value to calculate frequency-voltage
table. So export the tegra_sku_info.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
