- Use radeon hpd enum consistently (in both hotplug and dp)
- Legacy r100 with DVI should be HPD_1 not NONE
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some LVDS connectors don't have a ddc bus, so reset the
ddc bus to invalid before parsing the next connector
to avoid using stale ddc bus data. Should fix
fdo bug 28164.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* anholt/drm-intel-next: (515 commits)
drm/i915: Fix out of tree builds
drm/i915: move fence lru to struct drm_i915_fence_reg
drm/i915: don't allow tiling changes on pinned buffers v2
drm/i915: Be extra careful about A/D matching for multifunction SDVO
drm/i915: Fix DDC bus selection for multifunction SDVO
drm/i915: cleanup mode setting before unmapping registers
drm/i915: Make fbc control wrapper functions
drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
drm/i915: Use spatio-temporal dithering on PCH
[MTD] Remove zero-length files mtdbdi.c and internal.ho
pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
libata: Fix several inaccuracies in developer's guide
slub: Fix bad boundary check in init_kmem_cache_nodes()
raid6: fix recovery performance regression
KEYS: call_sbin_request_key() must write lock keyrings before modifying them
KEYS: Use RCU dereference wrappers in keyring key type code
KEYS: find_keyring_by_name() can gain access to a freed keyring
ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
ALSA: take tu->qlock with irqs disabled
...
This patch is a combination of the previous two profile
patches, but without the index bugs. It cleans up and
fixes some issues with pm profile setup on r6xx chips.
Some tables have different orderings for the power states,
also, r600 only has 1 clock mode per power state. On
desktop cards there are no battery modes, so the low and high
power states are the same. For the low profile case, choose
the lower clock mode.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Separate dynpm and profile based power management methods. You can select the pm method
by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
"default" - default clocks
"auto" - select between low and high based on ac/dc state
"low" - DC, low power mode
"high" - AC, performance mode
The current base profile is "default", but it should switched to "auto" once we've tested
on more systems. Switching the state is a matter of echoing the requested profile to
power_profile in sysfs. The lowest power states are selected automatically when dpms turns
the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment. We can revisit this later once we
have basic pm in.
- Move pm init/fini to modesetting path. pm is tightly coupled with display state. Make sure
display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option. It's now selectable via sysfs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The lowest power states often cause display problems, so only enable
them when all displays are off.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GUI idle interrupts don't seem to work terribly well on r500 and earlier,
so let's use a fence instead.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to handle the ring while we've already locked it, so split out
the allocation and commit functions in order to allow them to be used.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- disable gui idle interrupt use
Seems to hang some r5xx chips
- move vbl range check into
existing vbl check function in
radeon_pm.c
- disable crtc mc acccess for the
whole reclocking process
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This seems to be relatively stable now, so enable it for these chipsets
too.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vblank interrupt on r600 doesn't seem to be especially reliable, so
perform some sanity checks before the actual reclock.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm code could take vram_mutex followed by cp_mutex, while the
reclocking code would do the reverse. Hilarity could ensue.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to choose the correct PM state to transition into before starting
the actual change. Call radeon_get_power_state() at the top of the clock
setting to do so.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With luck, dynamic memory reclocking on r600 should be stable with
the previous patches. Enable it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm bo workqueue may touch objects while we're reclocking, so make
sure it's blocked until we're done.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We want to be able to prevent the delayed workqueue from changing state
while we're reclocking, so add an API to block and unblock it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to block the drm core from doing anything that may touch our vram
during reclock, so take the drm mutex for the duration.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Touching vram while the card is reclocking can lead to lockups. Unmap
any pages that could be touched by the CPU and block any accesses to
vram until the reclocking is complete.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's a moderate amount of effort involved in setting the card up for
clock transitions, so unify the codepaths to make it easier to implement.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add two new sysfs attributes:
- dynpm
- power_state
Echoing 0/1 to dynpm disables/enables dynamic power management.
The driver scales the sclk dynamically based on the number of
queued fences. dynpm only scales sclk dynamically in single head
mode.
Echoing x.y to power_state selects a static power state (x) and clock
mode (y). This allows you to statically select a power state and clock
mode. Selecting a static clock mode will disable dynpm.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- pm_misc() - handles voltage, pcie lanes, and other non
clock related power mode settings. Currently disabled.
Needs further debugging
- pm_prepare() - disables crtc mem requests right now.
All memory clients need to be disabled when changing
memory clocks. This function can be expanded to include
disabling fb access as well.
- pm_finish() - enable active memory clients.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- remove non_clock_info struct
- track power state misc flags
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just adds overhead when the power state will never change.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Hook the atom table parsing up to module loading, so we can automatically
load the appropriate hwmon drivers.
Based on initial patch for r6xx from Matthew Garrett
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This also simplifies the code and enables reclocking with multiple heads
active by tracking whether the power states are single or multi-head
capable.
Eventually, we will want to select a power state based on external
factors (AC/DC state, user selection, etc.).
(v2) Update for evergreen
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On pre-r6xx, the power mode array is usually ordered:
low
...
high
default
On r6xx+:
default
low
...
high
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
