Fix error distribution by immediately delivering the errors to all the
affected calls rather than deferring them to a worker thread. The problem
with the latter is that retries and things can happen in the meantime when we
want to stop that sooner.
To this end:
(1) Stop the error distributor from removing calls from the error_targets
list so that peer->lock isn't needed to synchronise against other adds
and removals.
(2) Require the peer's error_targets list to be accessed with RCU, thereby
avoiding the need to take peer->lock over distribution.
(3) Don't attempt to affect a call's state if it is already marked complete.
Signed-off-by: David Howells <dhowells@redhat.com>
It seems that enabling IPV6_RECVERR on an IPv6 socket doesn't also turn on
IP_RECVERR, so neither local errors nor ICMP-transported remote errors from
IPv4 peer addresses are returned to the AF_RXRPC protocol.
Make the sockopt setting code in rxrpc_open_socket() fall through from the
AF_INET6 case to the AF_INET case to turn on all the AF_INET options too in
the AF_INET6 case.
Fixes: f2aeed3a591f ("rxrpc: Fix error reception on AF_INET6 sockets")
Signed-off-by: David Howells <dhowells@redhat.com>
Make the following changes to improve the robustness of the code that sets
up a new service call:
(1) Cache the rxrpc_sock struct obtained in rxrpc_data_ready() to do a
service ID check and pass that along to rxrpc_new_incoming_call().
This means that I can remove the check from rxrpc_new_incoming_call()
without the need to worry about the socket attached to the local
endpoint getting replaced - which would invalidate the check.
(2) Cache the rxrpc_peer struct, thereby allowing the peer search to be
done once. The peer is passed to rxrpc_new_incoming_call(), thereby
saving the need to repeat the search.
This also reduces the possibility of rxrpc_publish_service_conn()
BUG()'ing due to the detection of a duplicate connection, despite the
initial search done by rxrpc_find_connection_rcu() having turned up
nothing.
This BUG() shouldn't ever get hit since rxrpc_data_ready() *should* be
non-reentrant and the result of the initial search should still hold
true, but it has proven possible to hit.
I *think* this may be due to __rxrpc_lookup_peer_rcu() cutting short
the iteration over the hash table if it finds a matching peer with a
zero usage count, but I don't know for sure since it's only ever been
hit once that I know of.
Another possibility is that a bug in rxrpc_data_ready() that checked
the wrong byte in the header for the RXRPC_CLIENT_INITIATED flag
might've let through a packet that caused a spurious and invalid call
to be set up. That is addressed in another patch.
(3) Fix __rxrpc_lookup_peer_rcu() to skip peer records that have a zero
usage count rather than stopping and returning not found, just in case
there's another peer record behind it in the bucket.
(4) Don't search the peer records in rxrpc_alloc_incoming_call(), but
rather either use the peer cached in (2) or, if one wasn't found,
preemptively install a new one.
Fixes: 8496af50eb38 ("rxrpc: Use RCU to access a peer's service connection tree")
Signed-off-by: David Howells <dhowells@redhat.com>
Do more up-front checking on incoming packets to weed out invalid ones and
also ones aimed at services that we don't support.
Whilst we're at it, replace the clearing of call and skew if we don't find
a connection with just initialising the variables to zero at the top of the
function.
Signed-off-by: David Howells <dhowells@redhat.com>
In the input path, a received sk_buff can be marked for rejection by
setting RXRPC_SKB_MARK_* in skb->mark and, if needed, some auxiliary data
(such as an abort code) in skb->priority. The rejection is handled by
queueing the sk_buff up for dealing with in process context. The output
code reads the mark and priority and, theoretically, generates an
appropriate response packet.
However, if RXRPC_SKB_MARK_BUSY is set, this isn't noticed and an ABORT
message with a random abort code is generated (since skb->priority wasn't
set to anything).
Fix this by outputting the appropriate sort of packet.
Also, whilst we're at it, most of the marks are no longer used, so remove
them and rename the remaining two to something more obvious.
Fixes: 248f219cb8bc ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix RTT information gathering in AF_RXRPC by the following means:
(1) Enable Rx timestamping on the transport socket with SO_TIMESTAMPNS.
(2) If the sk_buff doesn't have a timestamp set when rxrpc_data_ready()
collects it, set it at that point.
(3) Allow ACKs to be requested on the last packet of a client call, but
not a service call. We need to be careful lest we undo:
bf7d620abf22c321208a4da4f435e7af52551a21
Author: David Howells <dhowells@redhat.com>
Date: Thu Oct 6 08:11:51 2016 +0100
rxrpc: Don't request an ACK on the last DATA packet of a call's Tx phase
but that only really applies to service calls that we're handling,
since the client side gets to send the final ACK (or not).
(4) When about to transmit an ACK or DATA packet, record the Tx timestamp
before only; don't update the timestamp afterwards.
(5) Switch the ordering between recording the serial and recording the
timestamp to always set the serial number first. The serial number
shouldn't be seen referenced by an ACK packet until we've transmitted
the packet bearing it - so in the Rx path, we don't need the timestamp
until we've checked the serial number.
Fixes: cf1a6474f807 ("rxrpc: Add per-peer RTT tracker")
Signed-off-by: David Howells <dhowells@redhat.com>
There's a check in rxrpc_data_ready() that's checking the CLIENT_INITIATED
flag in the packet type field rather than in the packet flags field.
Fix this by creating a pair of helper functions to check whether the packet
is going to the client or to the server and use them generally.
Fixes: 248f219cb8bc ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Commit b2d35fa5fc80 ("selftests: add headers_install to lib.mk")
introduced a requirement that Makefiles more than one level below the
selftests directory need to define top_srcdir, but it didn't update
any of the powerpc Makefiles.
This broke building all the powerpc selftests with eg:
make[1]: Entering directory '/src/linux/tools/testing/selftests/powerpc'
BUILD_TARGET=/src/linux/tools/testing/selftests/powerpc/alignment; mkdir -p $BUILD_TARGET; make OUTPUT=$BUILD_TARGET -k -C alignment all
make[2]: Entering directory '/src/linux/tools/testing/selftests/powerpc/alignment'
../../lib.mk:20: ../../../../scripts/subarch.include: No such file or directory
make[2]: *** No rule to make target '../../../../scripts/subarch.include'.
make[2]: Failed to remake makefile '../../../../scripts/subarch.include'.
Makefile:38: recipe for target 'alignment' failed
Fix it by setting top_srcdir in the affected Makefiles.
Fixes: b2d35fa5fc80 ("selftests: add headers_install to lib.mk")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Fix a long standing race bug when destroying comp_event file descriptors
- srp, hfi1, bnxt_re: Various driver crashes from missing validation and
other cases
- Fixes for regressions in patches merged this window in the gid cache,
devx, ucma and uapi.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEfB7FMLh+8QxL+6i3OG33FX4gmxoFAlutG7QACgkQOG33FX4g
mxps3Q//fPL1o4Na/nx/aSmtfcEuPxjXwczUbB0MzlN7rKu0HjrES/DOXbGJZgS7
5XGu7TQyOBWzpZHZM4Xs+EjTdVY9pOK5+Q+t76Ns1vZsblCATJPOCIYMVkr+zM5T
zQxEfarlz8kEPWVz/TBAM7djoSkGXNLQQ1ttSVJBSAindhb25NzoiV1fsFGkXKmT
xbZHW03K1o4dZMf0JJO77eu1m9tkRfX0iFXBg4efgNOZtl9MP4l5lRwPqyRdGhMO
MvBNCJte/4dKlg5TeoVtp8B0sJvrO6QOj878VqYH4nL8uW2lZWFuzB7ZWxWGxMb/
VgXwpmXyDuTUjX9gn3kQToG8L9FJqsMzPZGBePMjilJqpgpqoVZpQ8i674JBZznF
as/bRSLdkA4PL5upFepBD/j9ep9LGIb6ojDcUSmwB+aJ99ZtlFUOhdf4ehQ2x9MU
WETIcdSqlmFjhY2IoHFKEr5PP3NGIDtPlvZbAmJrrne3uTCwXChXeZgzX1S6AHkY
djvDEaV8DrMmdJc0XTIOIQvxzMnHuoCo3oHdVaJMLudGkw1NKMN84SkIPb6U2Qjk
QiPf3pRRUazO6tqJfEZr8Es5lQjYkZUK4wKagOJKdcLBAubEnMhrsvECXQuoFWT8
sYhzK3AwyEaXp4Y3VbA+aqjZA/AhtPk/l3QKesU6u7hoLtiawoc=
=cjxG
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Jason writes:
"Second RDMA rc pull request
- Fix a long standing race bug when destroying comp_event file descriptors
- srp, hfi1, bnxt_re: Various driver crashes from missing validation
and other cases
- Fixes for regressions in patches merged this window in the gid
cache, devx, ucma and uapi."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/core: Set right entry state before releasing reference
IB/mlx5: Destroy the DEVX object upon error flow
IB/uverbs: Free uapi on destroy
RDMA/bnxt_re: Fix system crash during RDMA resource initialization
IB/hfi1: Fix destroy_qp hang after a link down
IB/hfi1: Fix context recovery when PBC has an UnsupportedVL
IB/hfi1: Invalid user input can result in crash
IB/hfi1: Fix SL array bounds check
RDMA/uverbs: Fix validity check for modify QP
IB/srp: Avoid that sg_reset -d ${srp_device} triggers an infinite loop
ucma: fix a use-after-free in ucma_resolve_ip()
RDMA/uverbs: Atomically flush and mark closed the comp event queue
cxgb4: fix abort_req_rss6 struct
trace_block_unplug() takes true for explicit unplugs and false for
implicit unplugs. schedule() unplugs are implicit and should be
reported as timer unplugs. While correct in the legacy code, this has
been inverted in blk-mq since 4.11.
Cc: stable@vger.kernel.org
Fixes: bd166ef183c2 ("blk-mq-sched: add framework for MQ capable IO schedulers")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On x86-64, the parametrized selftest code for rseq crashes with a
segmentation fault when compiled with -fpie. This happens when the
param_test binary is loaded at an address beyond 32-bit on x86-64.
The issue is caused by use of a 32-bit register to hold the address
of the loop counter variable.
Fix this by using a 64-bit register to calculate the address of the
loop counter variables as an offset from rip.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # v4.18
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: linux-kselftest@vger.kernel.org
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Chris Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Maurer <bmaurer@fb.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
.max_tfd_queue_size was ommited for 1000 card serries leading to oops in
swiotlb.
Fixes: 7b3e42ea2ead ("iwlwifi: support multiple tfd queue max sizes for different devices")
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When dax_lock_mapping_entry() has to sleep to obtain entry lock, it will
fail to unlock mapping->i_pages spinlock and thus immediately deadlock
against itself when retrying to grab the entry lock again. Fix the
problem by unlocking mapping->i_pages before retrying.
Fixes: c2a7d2a11552 ("filesystem-dax: Introduce dax_lock_mapping_entry()")
Reported-by: Barret Rhoden <brho@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit
1958b5fc4010 ("x86/boot: Add early boot support when running with SEV active")
can occasionally cause system resets when kexec-ing a second kernel even
if SEV is not active.
That's because get_sev_encryption_bit() uses 32-bit rIP-relative
addressing to read the value of enc_bit - a variable which caches a
previously detected encryption bit position - but kexec may allocate
the early boot code to a higher location, beyond the 32-bit addressing
limit.
In this case, garbage will be read and get_sev_encryption_bit() will
return the wrong value, leading to accessing memory with the wrong
encryption setting.
Therefore, remove enc_bit, and thus get rid of the need to do 32-bit
rIP-relative addressing in the first place.
[ bp: massage commit message heavily. ]
Fixes: 1958b5fc4010 ("x86/boot: Add early boot support when running with SEV active")
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-kernel@vger.kernel.org
Cc: tglx@linutronix.de
Cc: mingo@redhat.com
Cc: hpa@zytor.com
Cc: brijesh.singh@amd.com
Cc: kexec@lists.infradead.org
Cc: dyoung@redhat.com
Cc: bhe@redhat.com
Cc: ghook@redhat.com
Link: https://lkml.kernel.org/r/20180927123845.32052-1-kasong@redhat.com
After write SSD completed, bcache schedules journal_write work to
system_wq, which is a public workqueue in system, without WQ_MEM_RECLAIM
flag. system_wq is also a bound wq, and there may be no idle kworker on
current processor. Creating a new kworker may unfortunately need to
reclaim memory first, by shrinking cache and slab used by vfs, which
depends on bcache device. That's a deadlock.
This patch create a new workqueue for journal_write with WQ_MEM_RECLAIM
flag. It's rescuer thread will work to avoid the deadlock.
Signed-off-by: Guoju Fang <fangguoju@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The combination of defined constants are used to present the
state of IRQ so the magic numbers has been replaced.
This is a simple coding style change which should have no impact on
runtime code execution.
Signed-off-by: Xue Liu <liuxuenetmail@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
[Why]
EDID emulation didn't work properly for linux, as we stop programming
if nothing is connected physically.
[How]
We get a flag from DRM when we want to do edid emulation. We check if
this flag is true and nothing is connected physically, if so we only
program the front end using VIRTUAL_SIGNAL.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There have been a few reports of Vega10 display remaining blank
after S3 resume. The regression is caused by workaround for mode
change on Vega10 - skip set_bandwidth if stream count is 0.
As a result we skipped dispclk reset on suspend, thus on resume
we may skip the clock update assuming it hasn't been changed.
On some systems it causes display blank or 'out of range'.
[How]
Revert "drm/amd/display: Fix Vega10 black screen after mode change"
Verified that it hadn't cause mode change regression.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The vce cancel_delayed_work_sync never be called.
driver call the function in error path.
This caused the A+A suspend hang when runtime pm enebled.
As we will visit the smu in the idle queue. this will cause
smu hang because the dgpu has been suspend, and the dgpu also
will be waked up. As the smu has been hang, so the dgpu resume
will failed.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This reverts commit 0c08754b59da5557532d946599854e6df28edc22.
commit 0c08754b59da
("drm/panel: Add device_link from panel device to DRM device")
creates a circular dependency under these circumstances:
1. The panel depends on dsi-host because it is MIPI-DSI child
device.
2. dsi-host depends on the drm parent device (connector->dev->dev)
this should be allowed.
3. drm parent dev (connector->dev->dev) depends on the panel
after this patch.
This makes the dependency circular and while it appears it
does not affect any in-tree drivers (they do not seem to have
dsi hosts depending on the same parent device) this does not
seem right.
As noted in a response from Andrzej Hajda, the intent is
likely to make the panel dependent on the DRM device
(connector->dev) not its parent. But we have no way of
doing that since the DRM device doesn't contain any
struct device on its own (arguably it should).
Revert this until a proper approach is figured out.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927124130.9102-1-linus.walleij@linaro.org
Commit a46b53672b2c ("xen/blkfront: cleanup stale persistent grants")
added support for purging persistent grants when they are not in use. As
part of the purge, the grants were removed from the grant buffer, This
eventually causes the buffer to become empty, with BUG_ON triggered in
get_free_grant(). This can be observed even on an idle system, within
20-30 minutes.
We should keep the grants in the buffer when purging, and only free the
grant ref.
Fixes: a46b53672b2c ("xen/blkfront: cleanup stale persistent grants")
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
rxrpc_find_connection_rcu() initialises variable k twice with the same
information. Remove one of the initialisations.
Signed-off-by: David Howells <dhowells@redhat.com>
debugfs_remove has taken the IS_ERR into account. Just
remove the unnecessary condition.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
The smatch utility reports a possible leak:
smatch warnings:
drivers/clocksource/timer-atmel-pit.c:183 at91sam926x_pit_dt_init() warn: possible memory leak of 'data'
Ensure data is freed before exiting with an error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Use array_index_nospec() to sanitize i with respect to speculation.
Note that the user doesn't control i directly, but can make it out
of bounds by not finding a threshold in the array.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[add note about user control, as explained by Masashi]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current netpoll implementation in the bnxt_en driver has problems
that may miss TX completion events. bnxt_poll_work() in effect is
only handling at most 1 TX packet before exiting. In addition,
there may be in flight TX completions that ->poll() may miss even
after we fix bnxt_poll_work() to handle all visible TX completions.
netpoll may not call ->poll() again and HW may not generate IRQ
because the driver does not ARM the IRQ when the budget (0 for netpoll)
is reached.
We fix it by handling all TX completions and to always ARM the IRQ
when we exit ->poll() with 0 budget.
Also, the logic to ACK the completion ring in case it is almost filled
with TX completions need to be adjusted to take care of the 0 budget
case, as discussed with Eric Dumazet <edumazet@google.com>
Reported-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Song Liu <songliubraving@fb.com>
Tested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When add vxlan ttl inherit support, I forgot to fill it when dump
vlxan info. Fix it now.
Fixes: 72f6d71e491e6 ("vxlan: add ttl inherit support")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A HWMON device is only registered is the SFP module supports the
diagnostic page and is complient to SFF8472. Don't unconditionally
unregister the hwmon device when the SFP module is remove, otherwise
we access data structures which don't exist.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 1323061a018a ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1713:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
cm_info->ip_version = TCP_IPV4;
~ ^~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1733:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
cm_info->ip_version = TCP_IPV6;
~ ^~~~~~~~
2 warnings generated.
Use the appropriate values from the expected type, qed_tcp_ip_version:
TCP_IPV4 = QED_TCP_IPV4 = 0
TCP_IPV6 = QED_TCP_IPV6 = 1
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when a constant is used in a boolean context as it thinks a
bitwise operation may have been intended.
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: warning: use of logical
'&&' with constant operand [-Wconstant-logical-operand]
if (!p_iov->b_pre_fp_hsi &&
^
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: use '&' for a
bitwise operation
if (!p_iov->b_pre_fp_hsi &&
^~
&
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: remove constant
to silence this warning
if (!p_iov->b_pre_fp_hsi &&
~^~
1 warning generated.
This has been here since commit 1fe614d10f45 ("qed: Relax VF firmware
requirements") and I am not entirely sure why since 0 isn't a special
case. Just remove the statement causing Clang to warn since it isn't
required.
Link: https://github.com/ClangBuiltLinux/linux/issues/126
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b89f04c61efe ("bonding: deliver link-local packets with
skb->dev set to link that packets arrived on") changed the behavior
of how link-local-multicast packets are processed. The change in
the behavior broke some legacy use cases where these packets are
expected to arrive on bonding master device also.
This patch passes the packet to the stack with the link it arrived
on as well as passes to the bonding-master device to preserve the
legacy use case.
Fixes: b89f04c61efe ("bonding: deliver link-local packets with skb->dev set to link that packets arrived on")
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_roce.c:153:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
flavor = ROCE_V2_IPV6;
~ ^~~~~~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_roce.c:156:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
flavor = MAX_ROCE_MODE;
~ ^~~~~~~~~~~~~
2 warnings generated.
Use the appropriate values from the expected type, roce_flavor:
ROCE_V2_IPV6 = RROCE_IPV6 = 2
MAX_ROCE_MODE = MAX_ROCE_FLAVOR = 3
While we're add it, ditch the local variable flavor, we can just return
the value directly from the switch statement.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang complains when one enumerated type is implicitly converted to
another.
drivers/net/ethernet/qlogic/qed/qed_vf.c:686:6: warning: implicit
conversion from enumeration type 'enum qed_tunn_mode' to different
enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
QED_MODE_L2GENEVE_TUNN,
^~~~~~~~~~~~~~~~~~~~~~
Update mask's parameter to expect qed_tunn_mode, which is what was
intended.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:163:25: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->vxlan.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:165:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->l2_gre.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:167:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->ip_gre.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:169:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->l2_geneve.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:171:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->ip_geneve.tun_cls = type;
~ ^~~~
5 warnings generated.
Avoid this by changing type to an int.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in ms_to_errno array of error messages
and remove confusing "not" from the error text since the error code
refers to an uninitialized error code.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_VERBOSE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: fix WoL handling when suspending the PHY
phy_suspend doesn't always recognize that WoL is enabled and therefore
suspends the PHY when it should not. First idea to address the issue
was to reuse checks used in mdio_bus_phy_may_suspend which check
whether relevant devices are wakeup-enabled.
Florian raised some concerns because drivers may enable wakeup even if
WoL isn't enabled (e.g. certain USB network drivers).
The new approach focuses on reducing the risk to break existing stuff.
We add a flag wol_enabled to struct net_device which is set in
ethtool_set_wol(). Then this flag is checked in phy_suspend().
This doesn't cover 100% of the cases yet (e.g. if WoL is enabled w/o
explicit configuration), but it covers the most relevant cases with
very little risk of regressions.
v2:
- Fix a typo
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Core of the problem is that phy_suspend() suspends the PHY when it
should not because of WoL. phy_suspend() checks for WoL already, but
this works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.
This patch uses new member wol_enabled of struct net_device as
additional criteria in the check when not to suspend the PHY because
of WoL.
Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.
Fixes: f1e911d5d0df ("r8169: add basic phylib support")
Fixes: e8cfd9d6c772 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flag wol_enabled to struct net_device indicating whether
Wake-on-LAN is enabled. As first user phy_suspend() will use it to
decide whether PHY can be suspended or not.
Fixes: f1e911d5d0df ("r8169: add basic phylib support")
Fixes: e8cfd9d6c772 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e0511f6c1ccdd153cf063764e93ac177a8553c5d.
I commited the wrong version of these changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually there's nothing wrong with the two changes marked as "Fixes",
they just revealed a problem which has been existing before.
After having switched r8169 to phylib it was reported that WoL from
shutdown doesn't work any longer (WoL from suspend isn't affected).
Reason is that during shutdown phy_disconnect()->phy_detach()->
phy_suspend() is called.
A similar issue occurs when the phylib state machine calls
phy_suspend() when handling state PHY_HALTED.
Core of the problem is that phy_suspend() suspends the PHY when it
should not due to WoL. phy_suspend() checks for WoL already, but this
works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.
phylib knows about this and handles it in mdio_bus_phy_may_suspend(),
but that's used only when suspending the system, not in other cases
like shutdown.
Therefore factor out the relevant check from
mdio_bus_phy_may_suspend() to a new function phy_may_suspend() and
use it in phy_suspend().
Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.
Fixes: f1e911d5d0df ("r8169: add basic phylib support")
Fixes: e8cfd9d6c772 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to move metrics from the dst to rt6_info moved the call
to ip6_convert_metrics from ip6_route_add to ip6_route_info_create. In
doing so it makes the call in ip6_route_info_append redundant and
actually leaks the metrics installed as part of the ip6_route_info_create.
Remove the now unnecessary call.
Fixes: d4ead6b34b67f ("net/ipv6: move metrics from dst to rt6_info")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the deadline scheduler is used with a zoned block device, writes
to a zone will be dispatched one at a time. This causes the warning
message:
deadline: forced dispatching is broken (nr_sorted=X), please report this
to be displayed when switching to another elevator with the legacy I/O
path while write requests to a zone are being retained in the scheduler
queue.
Prevent this message from being displayed when executing
elv_drain_elevator() for a zoned block device. __blk_drain_queue() will
loop until all writes are dispatched and completed, resulting in the
desired elevator queue drain without extensive modifications to the
deadline code itself to handle forced-dispatch calls.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Fixes: 8dc8146f9c92 ("deadline-iosched: Introduce zone locking support")
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
