During image capture, the filling rate of the isoc packets is computed.
It is then used by a work queue to update the current JPEG quality.
Tested-by: Franck Bourdonnec <fbourdonnec@chez.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A marker 'ff ff 00 c4 c4 96' indicates an end of frame.
It is 62 bytes long and may be splitted on 2 packets.
It contains a flag 'USB full' which indicates that the frame is truncated.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The infrared was set by sensor write instead of bridge GPIO.
It is now settable by the standard control ILLUMINATOR_1.
A module parameter permits to set the right GPIO bit according
to the StarCam model.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
__devinit* must not be used in USB drivers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While going through windows inf file I found more usb-id, add a comment
with this id for future reference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looking at the windows inf file, for usb ids with a sensor type where probing
is needed to determine the type (for example ov7630 or soi768), this is
needed for all bridge variants with a usb id indicating this sensor type.
So do the probing to determine the actual sensor type for types where the
usb-id info is not 100% deterministic, independent of the bridge type.
If you look through the list of currently active usb ids in sonixj, this
effectively only changes the code path for 0c45:60fe (sn9c105 + ov7630) and
0c45:612e (sn9c110 + ov7630), which according to the inf file can have a
soi768 instead of a ov7630 just like the sn9c120 + ov7630 models where we
already probe for a soi7630.
The main reason for this code change is to keep the code paths as bridge
variant independent as possible, so that we don't need a lot of special
per bridge cases, as we enable more usb-ids in the future.
This change makes the 0c45:60fe code path identical to the successfully
tested 0c45:613e, so also make sonixj the default driver for 0c45:60fe.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both we and the windows driver make no sensor specific differences
(with some exceptions) for different sonixj bridge types. Thus if a
sn9c105 bridge has been successfully tested with a sensor, the same
sensor can be successfully used with a sn9c120 bridge too.
Using this knowledge we can move over most usb-ids too the sonixj
driver when both are compiled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial values of the registers 0x01 and 0x17 are taken from the sensor
table at capture start and updated according to the flag PDN_INV.
Their values are updated at each step of the capture initialization and
memorized for reuse in capture stop.
This patch also fixed automatically some bad hardcoded values of these
registers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The flag PDN_INV indicates that the sensor pin S_PWR_DN has not the same
value as other webcams with the same sensor. For now, only two webcams have
been so detected: the Microsoft's VX1000 and VX3000.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The errors were found by checkpatch.pl. Most fixes are:
- remove spaces followed by TAB(s),
- split lines greater than 80 characters,
- move most '{'s from start of line to end of previous line.
(Some '{'s at start of line remain when the '}'s are on the same line)
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The PO2030N sensor chip found in hama AC-150 webcam supports horizontal
and vertical flipping the image by hardware.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The number 0xdd is used for marking delay init sequence steps.
Replace 0xdd values only if the meaning is delay.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced by commit d5aa3856fd
removing the probe sequence of hv7131r with bridge sn9c120 and so, letting
the sensor inactive.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced by commit 23a98274cc
applying values of sensor sp80708 to sensors hv7131r and mi0360.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver sn9c102 does not know about the sensor mi0360b.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'end of image' block may be splitted between two ISOC packets.
This case was not tested, so, some images could be lost and concatenated
to previous one(s), raising 'frame overflow' errors.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sensor enum definition was not at the right place.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bit 0x04 of the bridge register 02 (GPIO) is used for audio connection
in webcams containing the bridge SN9C105. This patch sets it correctly,
according to the presence of an audio device.
Tested-by: Kyle Baker <kyleabaker@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcams 0c45:613e may contain the sensors ov7630 or soi768.
A sensor probe is done at init time when the sensor is declared ov7630.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
