- reconfigure SPI baud from speed_hz of each spi transfer
- according to spi_transfer.bits_per_word to reprogram register and setup
correct SPI operation handlers
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time
- move this static things to the blackfin board file
- add pin_req array to struct bfin5xx_spi_master
- tested on BF537/BF548 with SPI flash
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set correct baud for spi mmc and enable SPI only after DMA is started.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in u16_cs_chg_reader to read data_len-2 bytes data firstly, then read
out the last 2 bytes data
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move global SPI regs_base and dma_ch to struct driver_data. Test on BF54x SPI
Flash with 2 spi_master devices enabled.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move spin/waits to more correct locations in bfin SPI driver.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix SPI driver to work with SPI flash ST M25P16 on bf548
Currently the SPI driver enables the SPI controller and sets the SPI baud
register for each SPI transfer. But they should never be changed within a SPI
message session, in which several SPI transfers are pumped.
This patch moves SPI setting to the begining of a message session, and
never disables SPI controller until an error occurs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use portmux mechanism to support SPI busses 1 and 2, instead of just the
original bus 0.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update spi driver to support multi-ports by using platform resources; tested
on STAMP537+SPI_MMC, other boards need more testing. Plus other minor
updates.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent people from setting bits in ctl_reg that the SPI framework already
handles, hopefully we can one day drop ctl_reg completely
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Respect per-transfer cs_change field (protocol tweaking support) by
adding and using cs_active/cs_deactive functions.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup and error handling
- add error handling in SPI bus driver with selecting clients
- use proper defines to access Blackfin MMRs
- remove useless SSYNCs
- cleaner use of portmux calls
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use new Blackfin portmux interface, add error handling.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initial BF54x SPI support
- support BF54x SPI0
- clean up some code (whitespace etc)
- will support multiports in the future
- start using portmux calls
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification. (Most didn't.)
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify spi_sync calling convention, eliminating the need to check both
the return value AND the message->status. In consequence, this corrects
misbehaviours of spi_read and spi_write (which only checked the former) and
their callers.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add comment to at25 driver that it's for EEPROM chips, not FLASH
chips ... the AT25 series has both types of chip, and sometimes
they're even pin-compatible. The command sets are different, as
is the treatment of erasure. (FLASH needs explicit erasure, but
with EEPROM it's implicit.) Note that all vendors seem to have
this same confusion in their *25* series SPI memory parts.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make spi_write_then_read() use a mutex not a binary semaphore.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We must make sure that the RTC_DEV_BUSY flag has proper lock semantics,
i.e. that the RTC_DEV_BUSY stores clearing the flag don't get reordered
before the preceeding stores and loads and vice versa.
Spotted by Nick Piggin.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lately I've got this nice badness on mdio bus removal:
Device 'e0103120:06' does not have a release() function, it is broken and must be fixed.
------------[ cut here ]------------
Badness at drivers/base/core.c:107
NIP: c015c1a8 LR: c015c1a8 CTR: c0157488
REGS: c34bdcf0 TRAP: 0700 Not tainted (2.6.23-rc5-g9ebadfbb-dirty)
MSR: 00029032 <EE,ME,IR,DR> CR: 24088422 XER: 00000000
...
[c34bdda0] [c015c1a8] device_release+0x78/0x80 (unreliable)
[c34bddb0] [c01354cc] kobject_cleanup+0x80/0xbc
[c34bddd0] [c01365f0] kref_put+0x54/0x6c
[c34bdde0] [c013543c] kobject_put+0x24/0x34
[c34bddf0] [c015c384] put_device+0x1c/0x2c
[c34bde00] [c0180e84] mdiobus_unregister+0x2c/0x58
...
Though actually there is nothing broken, it just device
subsystem core expects another "pattern" of resource managment.
This patch implement phy device's release function, thus
we're getting rid of this badness.
Also small hidden bug fixed, hope none other introduced. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Eliminate an uninitialized variable warning. The code is correct, but
a pointer to the automatic variable 'addr' is passed to dma_alloc_coherent.
Since addr has never been initialized, and the compiler doesn't know
what dma_alloc_coherent will do with it, it complains.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turns out we're freeing the skb when we detect CRC error, but we're
not clearing out info->skb. We could either clear it and have the stack
reallocate it, or just leave it and the rx ring refill code will reuse
the one that was allocated.
Reusing a freed skb obviously caused some nasty crashes of various kind,
as reported by Brent Baude and David Woodhouse.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent deadlock in sky2 recovery logic. sky2_down calls napi_synchronize
which gets stuck if napi was already disabled.
Fix by rearranging slightly and not calling napi_disable until after
both ports are stopped. The napi_disable probably is being overly
paranoid, but it is safe now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mpc5200 fec driver is corrupting memory. This patch fixes two bugs
where the wrong skb was being referenced.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Don't program UDMA timings when programming PIO or MWDMA modes.
This has also a nice side-effect of fixing regression added by commit
681c80b5d9 ("libata: correct handling of
SRST reset sequences") (->set_piomode method for PIO0 is called before
->cable_detect method which checks UDMA timings to get the cable type).
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-by: "Thomas Lindroth" <thomas.lindroth@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the device IDs of legacy mode of MCP79 AHCI controller to ahci.c
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Highpoint RocketRAID boards using Marvell 7042 chips
overwrite the 9th sector of attached drives at boot time,
when those drives are configured as "Legacy" (the default)
in the HighPoint BIOS.
This kills GRUB, and probably other stuff.
But it all happens *before* Linux is even loaded.
So, for now we'll log a WARNING when such boards are detected,
and advise users to configure BIOS "JBOD" volumes instead,
which don't appear to suffer from this problem.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We need to run any DMA command with result taskfile requested in ADMA mode
when the port is in ADMA mode, otherwise it may try to use the legacy DMA engine
in ADMA mode which is not allowed. Enforce this with BUG_ON() since data
corruption could potentially result if this happened. Also, fail any attempt to
try and issue NCQ commands with result taskfile requested, since the hardware
doesn't allow this.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Make sure the restore psw masks are initialized.
[S390] Fix compile error on 31bit without preemption
[S390] dcssblk: prevent early access without own make_request function
[S390] cio: add missing reprobe loop end statement
[S390] cio: Issue SenseID per path.
When loading a dcss segment with the dcssblk driver, sometimes the
following kind of message appears:
bio too big device dcssblk0 (8 > 0)
Buffer I/O error on device dcssblk0, logical block 172016
..
The fix is to move the disk registration after setting the
make_request function, to avoid calls into generic_make_request
for dcssblock without having the make_request function set up
properly.
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add loop end statement to prevent looping over empty subchannel sets.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We may receive a unit check for every path when we issue a SenseID.
Unfortunately, the channel subsystem will try on a different path
every time if we use a lpm of 0xff, which will exhaust our retry
counter.
Therefore, revert SenseID to its previous per-path behaviour and
just leave out the suspend multipath reconnect.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: fix acpi-cpufreq boot crash due to _PSD return-by-reference
ACPI: Delete the IRQ operation in throttling controll via PTC
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (27 commits)
[INET]: Fix inet_diag dead-lock regression
[NETNS]: Fix /proc/net breakage
[TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure
[NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
[NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON
[DECNET]: dn_nl_deladdr() almost always returns no error
[IPV6]: Restore IPv6 when MTU is big enough
[RXRPC]: Add missing select on CRYPTO
mac80211: rate limit wep decrypt failed messages
rfkill: fix double-mutex-locking
mac80211: drop unencrypted frames if encryption is expected
mac80211: Fix behavior of ieee80211_open and ieee80211_close
ieee80211: fix unaligned access in ieee80211_copy_snap
mac80211: free ifsta->extra_ie and clear IEEE80211_STA_PRIVACY_INVOKED
SCTP: Fix build issues with SCTP AUTH.
SCTP: Fix chunk acceptance when no authenticated chunks were listed.
SCTP: Fix the supported extensions paramter
SCTP: Fix SCTP-AUTH to correctly add HMACS paramter.
SCTP: Fix the number of HB transmissions.
[TCP] illinois: Incorrect beta usage
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
LIB82596: correct data types for hardware addresses
via-velocity: don't oops on MTU change (resend)
Stop phy code from returning success to unknown ioctls.
SET_NETDEV_DEV() in fec_mpc52xx.c
net: smc911x: only enable for mpr2 on sh.
e1000: Fix NAPI state bug when Rx complete
sky2: turn of dynamic Tx watermark workaround (FE+ only)
sky2: don't use AER routines
sky2: revert to access PCI config via device space
cxgb - fix stats
cxgb - fix NAPI
cxgb - fix T2 GSO
ucc_geth: handle passing of RX-only and TX-only internal delay PHY connection type parameters
phylib: marvell: add support for TX-only and RX-only Internal Delay
phylib: add PHY interface modes for internal delay for tx and rx only
skge: MTU changing fix
skge: serial mode register values
skge version 1.13
skge: increase TX threshold for Jumbo
skge: fiber link up/down fix
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Fix broken Marvell 7042 support.
libata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port (errno=-19))
ata_piix: add more toshiba laptops to broken suspend list
libata: More IVB horkage from TSST
libata: report protocol and full CDB on error
Several fixes for the AVR32 PATA driver
sata_mv: fix compilation error when enabling DEBUG
Set proper ATA UDMA mode for bf548 according to system clock.
The previous commit ("uml: keep UML Kconfig in sync with x86") is not
enough, unfortunately. If we go that way, we need to add dependencies
on !UML for several options.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
