PMBus controllers optionally support PEC. Configure the driver
to use it if available to improve operational security.
Suggested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3886 is a is a dual PolyPhase DC/DC synchronous step-down switching
regulator controller. It is mostly command compatible to LTC3883,
but supports two phases instead of one.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2980 and LTM2987 are command compatible to LTC2977. They consist of
two LTC2977 on a single die, and are instantiated as two separate chips,
each supporting eight channels.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add additional chip ID for an older revision of LTC2978, as well
as two chip IDs for LTC3882. Turns out the LTC3882 does support the
LTC2978_MFR_SPECIAL_ID register, and reading it returns its chip ID,
but the register is undocumented.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per information from Linear Technologies, the ID mask is 12 bit
for all chips of this series. Use this mask to detect chips to ensure
that all chip revisions are detected.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The code used to determine historic low and high peaks is repeated
several times. Introduce helper functions to simplify it.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is becoming cumbersom to track per-chip feature support.
Introduce feature flag to simplify the code.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2975 is mostly compatible to LTC2974, but supports input current
and power measurement.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per datasheet, the chip ID for LTM4676 is 0x448x. This was observed
in real systems. In addition to that, chip ID 0x4401 was observed
as well. Research shows that the chip ID has been changed from 0x440x
to 0x448x in datasheet revision C. Add support for the additional chip ID.
Also add the chip ID for LTM4676A, which is functionally identical
to LTM4676.
Reported-by: Ananda Babu Nettam <anandab@juniper.net>
Cc: Ananda Babu Nettam <anandab@juniper.net>
Cc: Amit U Jain <amjain@juniper.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3882 is mostly compatible with LTC3880. Major differences are that it
does not measure the input current, and it no longer supports LTC's legacy
mechanism to identify the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Verifying the chip type is getting more complicated with new chips,
since not all chips support the same mechanism to read the chip type.
Move the code into a separate function to simplify adding support for
those chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This change sht15_reverse() to be generic bitrev8().
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add device IDs and references for Texas Instruments TPS544B20, TPS544B25,
TPS544C20, and TPS544C25 to the generic PMBus driver.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX20751 is a multiphase power controller with internal buck converter.
It uses VR12.0 to report the output voltage. This requires an explicit
driver, since the VR version can not be auto-detected.
The chip supports a manufacturer specific command to fine-tune the output
voltage. This command is not currently supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the IT8732F. This chip is pretty similar to IT8721F,
with the main difference being that the ADC LSB is 10.9 mV instead of
12 mV.
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADM1293 and ADM1294 are mostly compatible with other chips of the same
series, but have more configuration options. There are also some
differences in register details.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Introduce have_vout, have_vaux_status, have_pin_max, and have_uc_fault
to simplify adding support for new chips.
Also simplify error returns where appropriate to return immediately
on error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Each new chip supported by the driver has a new set of coefficients,
making hard-coding coefficients more and more cumbersome. Introduce
a datastructure and table to simplify configuration.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_regulator_ops is not modified after initialized, so make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pmbus_regulator_ops is for voltage regulators, so explicitly set
regulator type for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add f81768d (id 0x1210) currently found on Jetway motherboards.
It has 11 voltages but otherwise needed no special handling
in this driver.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The temperature value of Fintek F81866 is the same with
f71882fg. It located with 0x6c + 2*(nr), others located
with 0x6c + 2*(nr+1). We change the rule in f71882fg_probe(),
If type = f71858fg/f8000/f81866a. the temp_start will set to 0,
others are 1.
The F81866 over-temperature beep setting is not the same with
f71882fg too. They are using the same address 63H, but F81866 is
using bit 0/1/2 & 4/5/6, others are using bit 1/2/3 & 5/6/7,
So we copy from fxxxx_temp_beep_attr[] to f81866_temp_beep_attr
and change bit setting.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add New Fintek SuperIO F81866(0x1010) & F71868(0x1106)
with H/W Monitor functions.
We increased F71882FG_MAX_INS from 9 to 10 to read
F71868 10 voltage sets.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added fan output control registers.
Modes of operation are PWM (default) and DC.
Introduced show_pwm, store_pwm, nct7802_pwm_attrs, nct7802_pwm_group.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CPU fan speed going up and down on Dell Studio XPS 8100 for
unknown reasons. Without further debugging on the affected
machine, it is not possible to find the problem.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100121
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Jan C Peters <jcpeters89@gmail.com>
Cc: stable@vger.kernel.org # v4.0+, will need backport
[groeck: cleaned up description, comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Writing a large value into a voltage limit attribute can result
in an overflow due to an auto-conversion from unsigned long to
unsigned int.
Cc: Constantine Shulyupin <const@MakeLinux.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm attributes have well defined names, which should be used.
Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Cc: stable@vger.kernel.org #v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Add pwm[4-7] and the associated pwm[4-7]_mode attributes.
Signed-off-by: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
The mcp3021 scaling code is dividing the VDD (full-scale) value in
millivolts by the A2D resolution to obtain the scaling factor. When VDD
is 3300mV (the standard value) and the resolution is 12-bit (4096
divisions), the result is a scale factor of 3300/4096, which is always
one. Effectively, the raw A2D reading is always being returned because
no scaling is applied.
This patch fixes the issue and simplifies the register-to-volts
calculation, removing the unneeded "output_scale" struct member.
Signed-off-by: Nick Stevens <Nick.Stevens@digi.com>
Cc: stable@vger.kernel.org # v3.10+
[Guenter Roeck: Dropped unnecessary value check]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As per Documentation/hwmon/sysfs-interface, hwmon name attributes must
not include '-', so replace 'dell-smm' with 'dell_smm'.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNn0gACgkQMUfUDdst+ykCCQCgvdF4F2+Hy9+RATdk22ak1uq1
JDMAoJTf4oyaIEdaiOKfEIWg9MasS42B
=H5wD
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems"
* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
mei: me: wait for power gating exit confirmation
mei: reset flow control on the last client disconnection
MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
misc: sram: sort and clean up included headers
misc: sram: move reserved block logic out of probe function
misc: sram: add private struct device and virt_base members
misc: sram: report correct SRAM pool size
misc: sram: bump error message level on unclean driver unbinding
misc: sram: fix device node reference leak on error
misc: sram: fix enabled clock leak on error path
misc: mic: Fix reported static checker warning
misc: mic: Fix randconfig build error by including errno.h
uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
uio: pruss: Add CONFIG_HAS_IOMEM dependence
uio: pruss: Include <linux/sizes.h>
extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
parport: check exclusive access before register
w1: use correct lock on error in w1_seq_show()
...
- New driver for Microchip TC74
- Support for ncpXXwf104 added to ntc_thermistor driver
- Minor cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZKHZ
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for Microchip TC74
- support for ncpXXwf104 added to ntc_thermistor driver
- minor cleanup
* tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: add driver for Microchip TC74
hwmon: (ntc_thermistor) Improve precision of resistance calculation
hwmon: (ntc_thermistor) fix iio raw to microvolts conversion
hwmon: (atxp1) Drop auto-detection
hwmon: (atxp1) Drop FSF mailing address
hwmon: Allow compile test of GPIO consumers if !GPIOLIB
hwmon: (sht15) Constify platform_device_id
hwmon: (max197) Constify platform_device_id
hwmon: (ntc_thermistor) Add support for ncpXXwf104
Add hwmon driver for the Microchip TC74.
The TC74 is a single-input 8-bit I2C temperature sensor,
with +-2 degrees centigrade accuracy.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function get_ohm_of_thermistor has both the measured voltage and the
pullup voltage available in microvolts. But it was promptly converting
both to millivolts before using them to calculate the thermistor
resistance. That conversion unnecessarily hurt the precision of the
calculation.
For example, take the ncpXXwb473 connected to 5000 mV and pulled down
through a 47000 ohm resistor. At 25 C, the resistance of the thermistor
is 47000 ohms. The measured voltage will be 2500 mV. If we measure
instead 2501 mV, then the calculated resistance will be 46962 ohms --
a difference of 38 ohms. So the precision of the resistance estimate
could be increased by 38X by doing the calculations in microvolts.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function ntc_adc_iio_read was assuming both a 12 bit ADC and that
pullup_uv is the same as the ADC reference voltage. If either
assumption is false, then the result is incorrect.
Attempt to use iio_convert_raw_to_processed to convert the raw value to
microvolts. It will fail for iio channels that don't support support
IIO_CHAN_INFO_SCALE; in that case fall back to the assumptions.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Auto-detection for this chip is highly unreliable, and one of its
I2C addresses can also be used by EEPROMs, increasing the risk for
false positives even more. Drop auto-detection entirely to remove
the risk.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The FSF mailing address may change and does not provide any real value.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for the ntc thermistor NCPXXWF104 series.
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following error message is seen when loading the nct6683 driver
with DEBUG_LOCK_ALLOC enabled.
BUG: key ffff88040b2f0030 not in .data!
------------[ cut here ]------------
WARNING: CPU: 0 PID: 186 at kernel/locking/lockdep.c:2988
lockdep_init_map+0x469/0x630()
DEBUG_LOCKS_WARN_ON(1)
Caused by a missing call to sysfs_attr_init() when initializing
sysfs attributes.
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following error message is seen when loading the nct6775 driver
with DEBUG_LOCK_ALLOC enabled.
BUG: key ffff88040b2f0030 not in .data!
------------[ cut here ]------------
WARNING: CPU: 0 PID: 186 at kernel/locking/lockdep.c:2988
lockdep_init_map+0x469/0x630()
DEBUG_LOCKS_WARN_ON(1)
Caused by a missing call to sysfs_attr_init() when initializing
sysfs attributes.
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I2C address 0x37 may be used by EEPROMs, which can result in false
positives. Do not attempt to detect a chip at this address.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The former duplicates the functionality of the latter but is
neither documented nor arch-independent.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/1432645896-12588-4-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When configured via device tree, the associated iio device needs to be
measuring voltage for the conversion to resistance to be correct.
Return -EINVAL if that is not the case.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch splits CONFIG_I8K compile option to SENSORS_DELL_SMM and CONFIG_I8K.
Option SENSORS_DELL_SMM is now used to enable compilation of dell-smm-hwmon
driver and old CONFIG_I8K option to enable /proc/i8k interface in driver.
So this change allows to compile dell-smm-hwmon driver without legacy /proc/i8k
interface which is needed only for old Dell Inspirion models or for userspace
i8kutils package.
For backward compatibility when CONFIG_I8K is enabled then also SENSORS_DELL_SMM
is enabled and so driver dell-smm-hwmon (with /proc/i8k) is compiled.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit moves i8k driver to hwmon tree under name dell-smm-hwmon which is
better name then abbreviation i8k. For backward compatibility is added macro
MODULE_ALIAS("i8k") so modprobe will load driver also old name i8k. CONFIG_I8K
compile option was not changed.
This commit also adds me as maintainer of this new dell-smm-hwmon driver and
remove Guenter Roeck from list who is implicit maintainer all hwmon drivers.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the loop iterating over pwm_freq_cksel0 with a call to
find_closest_descending().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use find_closest() to locate the closest average in ina226_avg_tab.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pwm_config() must be called with a duty cycle of 0 prior to calling
pwm_disable() to ensure that the pwm signal is set to low.
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Feature macros work on sio_data as well, so use them there.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix
drivers/hwmon/ibmpowernv.c: In function 'get_logical_cpu':
drivers/hwmon/ibmpowernv.c:121:3:
error: implicit declaration of function 'get_hard_smp_processor_id'
seen for some configurations, possibly if SMP is not configured.
Fixes: 3df2f59f0a ("hwmon: (ibmpowernv) pretty print labels")
Cc: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The new OPAL device tree adds a few properties which can be used to add
extra information on the sensor label.
In the case of a cpu core sensor, the firmware exposes the physical
identifier of the core in the "ibm,pir" property. The driver
translates this identifier in a linux cpu number and prints out a
range corresponding to the hardware threads of the core (as they
share the same sensor).
The numbering gives a hint on the localization of the core in the
system (which socket, which chip).
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently, sensors are only identified by their type and index.
The new OPAL device tree can expose extra properties to identify
some sensors by their name or location. This patch adds the creation
of a new hwmon *_label attribute when such properties are detected.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The new OPAL device tree for sensors has a different layout and uses new
property names, for the type and for the handler used to capture the
sensor data.
This patch modifies the ibmpowernv driver to support such a tree in a
way preserving compatibility with older OPAL firmwares.
This is achieved by changing the error path of the routine parsing
an OPAL node name. The node is simply considered being from the new
device tree layout and fallback values are used.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This should shorten a bit the code necessary to create a hmwon attribute.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8620E is mostly compatible to IT7828F. Add generic support for it.
IT8620E supports up to 6 fan tachometers and 6 pwm controls.
Support for the 6th tachometer and for the additional pwm controls
are addded in separate patches.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8790E is a super-IO chip with three fan tachometers. It is mostly
compatible to IT8728F, but only supports three fan tachometers
instead of five.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some chips, in7 is always an internal voltage sensor. Introduce
feature flag to reflect this condition to simplify adding support
for new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ITE chips may have 'E', 'F', or both 'E' and 'F' suffixes.
Introduce suffic configuration to the it87_devices structure
to simplify adding new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On chips with newer PWM control, the PWM frequency divider is 256
instead of 128. Since the base PWM frequency remained the same, the actual
PWM frequency is half of what it used to be with the older PWM control
mechanism.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Detection if a pwm channel is supported was wrong on removal,
causing the code to try removing non-existing sysfs attributes.
That didn't matter much because sysfs attribute removal of non-existing
files fails silently, and because the wrong evaluation always returned
false, but should nevertheless be fixed.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The current OPAL firmware exposes the different sensors of an IBM Power
system using node names such as :
sensors/amb-temp#1-data
sensors/amb-temp#1-thrs
cooling-fan#1-data
cooling-fan#1-faulted
cooling-fan#1-thrs
cooling-fan#2-data
...
The ibmpowernv driver, when loaded, parses these names to extract the
sensor index and the sensor attribute name. Unfortunately, this scheme
makes it difficult to add sensors with a different layout (specially of
the same type, like temperature) as the sensor index calculated in OPAL
is directly used in the hwmon sysfs interface.
What this patch does is add a independent hwmon index for each sensor.
The increment of the hwmon index (temp, fan, power, etc.) is kept per
sensor type in the sensor_group table. The sensor_data table is used
to store the association of the hwmon and OPAL indexes, as we need to
have the same hwmon index for different attributes of a same sensor.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It simplifies the creation of the hwmon attributes and will help when
support for a new device tree layout is added. The patch also changes
the name of the routine to parse_opal_node_name().
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It simplifies the create_hwmon_attr_name() routine and it clearly isolates
the conversion done between the OPAL node names and hwmon attributes names.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It will help in adding different compatible properties, coming from a
new device tree layout for example.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Ambient is too restrictive as there can be other temperature channels :
core, memory, etc.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Auxiliary fan monitoring is not enabled on ASRock Z77 Pro4-M
with BIOS version 2.00 if booted in UEFI Ultra-FastBoot mode.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After a suspend/resume cycle it is not guaranteed that the hardware monitoring
device is still enabled. Ensure that this is the case after resume.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Get rid of #ifdef CONFIG_PM by using SIMPLE_DEV_PM_OPS and declaring suspend
and resume functions with __maybe_unused.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix build error when CONFIG_THERMAL=m and SENSORS_GPIO_FAN=y
by preventing that combination.
Fixes these build errors:
drivers/built-in.o: In function `gpio_fan_remove':
gpio-fan.c:(.text+0x21e97e): undefined reference to `thermal_cooling_device_unregister'
drivers/built-in.o: In function `gpio_fan_probe':
gpio-fan.c:(.text+0x21efbc): undefined reference to `thermal_cooling_device_register'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Cc: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix build errors when CONFIG_THERMAL=m and SENSORS_PWM_FAN=y
by restricting SENSORS_PWM_FAN to 'm' when THERMAL=m.
drivers/built-in.o: In function `pwm_fan_remove':
pwm-fan.c:(.text+0x22ba58): undefined reference to `thermal_cooling_device_unregister'
drivers/built-in.o: In function `pwm_fan_probe':
pwm-fan.c:(.text+0x22bebb): undefined reference to `thermal_of_cooling_device_register'
pwm-fan.c:(.text+0x22bf11): undefined reference to `thermal_cdev_update'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Address the following sparse warnings.
drivers/hwmon/pwm-fan.c:176:5: warning:
symbol 'pwm_fan_of_get_cooling_data' was not declared. Should it be static?
drivers/hwmon/pwm-fan.c:176:5: warning:
no previous prototype for 'pwm_fan_of_get_cooling_data'
pwm_fan_of_get_cooling_data is only used in the pwm-fan driver and thus should
be declared static.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allow gpio-fan to be used as thermal cooling device for platforms that
use GPIO maps to control fans.
As part of this change, we make the shutdown and remove logic the same
as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The PWM FAN device can now be used as a thermal cooling device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
