Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
the RC RX packet is defined as:
struct dib0700_rc_response {
...
u8 not_system;
u8 system;
...
u8 data;
u8 not_data;
The NEC protocol transmits in the order:
system
not_system
data
not_data
Note that the code defines the NEC extended scancode as:
scancode = be16_to_cpu(poll_reply->system16) << 8 | poll_reply->data;
i.e.
scancode = poll_reply->not_system << 16 |
poll_reply->system << 8 |
poll_reply->data;
Which, if the order *is* reversed, would mean that the scancode that
gets defined is in reality:
scancode = poll_reply->system << 16 |
poll_reply->not_system << 8 |
poll_reply->data;
Which is the same as the order used in drivers/media/rc/ir-nec-decoder.c.
This patch changes the code to match my assumption (the generated scancode
should, however, not change).
[m.chehab@samsung.com: rebased and fixed the decoding error message]
Signed-off-by: David Härdeman <david@hardeman.nu>
CC: Patrick Boettcher <pboettcher@kernellabs.com>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The arguments used for ir-kbd-i2c's get_key() functions are not
really suited for rc-core and the ir_raw/ir_key distinction is
just confusing.
Convert all of them to return a protocol/scancode/toggle triple instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Vincent:
[ 16.332247] xc2028 0-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000.
[ 16.344378] cxusb: i2c wr: len=64 is too big!
64 bytes is too short for firmware load on this device. So, increase it
to 80 bytes.
Reported-by: Vincent McIntyre <vincent.mcintyre@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that the custom motion detection API in this driver has been
replaced with a standard API there is no reason anymore to keep it
in staging. So (finally!) move it to drivers/media/usb.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename driver namespace according to current driver name. Old
msi3101 was name of reference design, msi2500 is name of chip
itself.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was a lot of duplicated functionality between different
stream format handling. Refactor functionality in order to get
rid of duplicated code.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
MEDIA_SDR_SUPPORT and I2C_MUX are needed for rtl2832_sdr.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SDR API is very new and surprises may occur. Due to that print
notice to remind possible users.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move msi3101 out of staging and rename to msi2500.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modify all users of si2157_config to correctly initialize all not
listed values to 0.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modify all users of si2157_config to correctly initialize all not
listed values to 0.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Print notice on driver load: "SDR API is still slightly
experimental and functionality changes may follow". It is just
remind possible used SDR API is very new and surprises may occur.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move it out of staging into media like all the other SDR drivers
too. There is no good reasons to keep these SDR drivers in staging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add software defined radio device support for media Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media fixes from Mauro Carvalho Chehab:
"A series of driver fixes:
- fix DVB-S tuning with tda1071
- fix tuner probe on af9035 when the device has a bad eeprom
- some fixes for the new si2168/2157 drivers
- one Kconfig build fix (for omap4iss)
- fixes at vpif error path
- don't lock saa7134 ioctl at driver's base core level, as it now
uses V4L2 and VB2 locking schema
- fix audio at hdpvr driver
- fix the aspect ratio at the digital timings table
- one new USB ID (at gspca_pac7302): Genius i-Look 317 webcam"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca_pac7302: Add new usb-id for Genius i-Look 317
[media] tda10071: fix returned symbol rate calculation
[media] tda10071: fix spec inversion reporting
[media] tda10071: add missing DVB-S2/PSK-8 FEC AUTO
[media] tda10071: force modulation to QPSK on DVB-S
[media] hdpvr: fix two audio bugs
[media] davinci: vpif: missing unlocks on error
[media] af9035: override tuner id when bad value set into eeprom
[media] saa7134: use unlocked_ioctl instead of ioctl
[media] media: v4l2-core: v4l2-dv-timings.c: Cleaning up code wrong value used in aspect ratio
[media] si2168: firmware download fix
[media] si2157: add one missing parenthesis
[media] si2168: add one missing parenthesis
[media] staging: tighten omap4iss dependencies
The issue was discovered by static analysis. It turns out that code is
somewhat insane, being
if (x) {...} else { if (x) {...} }
Edited it to do the only reasonable thing, which is to log the
information about the failed call. The most descriptive logging commands
set is taken from original code.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79801
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The colorspace for HDTV is REC709, not SMPTE240M.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l2_pix_format structure has no reserved field. It is embedded in
the v4l2_framebuffer structure which has no reserved fields either, and
in the v4l2_format structure which has reserved fields that were not
previously required to be zeroed out by applications.
To allow extending v4l2_pix_format, inline it in the v4l2_framebuffer
structure, and use the priv field as a magic value to indicate that the
application has set all v4l2_pix_format extended fields and zeroed all
reserved fields following the v4l2_pix_format field in the v4l2_format
structure.
The availability of this API extension is reported to userspace through
the new V4L2_CAP_EXT_PIX_FORMAT capability flag. Just checking that the
priv field is still set to the magic value at [GS]_FMT return wouldn't
be enough, as older kernels don't zero the priv field on return.
To simplify the internal API towards drivers zero the extended fields
and set the priv field to the magic value for applications not aware of
the extensions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 0ba2aeb6da increased the internal control ranges
to 64 bit, but that caused problems in drivers that use the minimum/maximum/step/default_value
control values in a division or modulus operations since not all architectures support
those natively.
Luckily, in almost all cases it is possible to just cast to 32 bits (the control value
is known to be 32 bits, so it is safe to cast). Only in v4l2-ctrls.c was it necessary to
use do_div in one function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
USB ID 0b48:3014.
USB interface: Cypress CY7C68013A-56LTXC
Demodulator: Silicon Labs Si2168-30
Tuner: Silicon Labs Si2158-20
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using anonymous initialization for dib0896 structs,
identify each field by name. That helps to understand what's
being initialized.
No functional changes.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since all the drivers that use `struct v4l2_fh' use the core
priority checking, the setting of the flag in the drivers can
be removed.
Signed-off-by: Ramakrishnan Muthukrishnan <ramakrmu@cisco.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Error handling code in poseidon_probe() misses usb_put_intf()
and usb_put_dev().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the MSI Digivox Trio device.
Signed-off-by: P. van Gaans <w3ird_n3rd@gmx.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the audio encoding is changed the driver calls hdpvr_set_audio
with the current opt->audio_input value. However, that should have
been opt->audio_input + 1. So changing the audio encoding inadvertently
changes the input as well. This bug has always been there.
The second bug was introduced in kernel 3.10 and that broke the
default_audio_input module option handling: the audio encoding was
never switched to AC3 if default_audio_input was set to 2 (SPDIF input).
In addition, since starting with 3.10 the audio encoding is always set
at the start the first bug now always happens when the driver is loaded.
In the past this bug would only surface if the user would change the
audio encoding after the driver was loaded.
Also fixes a small trivial typo (bufffer -> buffer).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Scott Doty <scott@corp.sonic.net>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tuner ID set into EEPROM is wrong in some cases, which causes driver
to select wrong tuner profile. That leads device non-working. Fix
issue by overriding known bad tuner IDs with suitable default value.
Thanks to MX-NET Telekomunikace s.r.o. for providing non-working
DTV stick, that I could fix the bug!
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the depth stream at 10bpp, for now use a 'depth_mode'
command line parameter to switch between video and depth mode.
Signed-off-by: Alexander Sosna <alexander@xxor.de>
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently gspca selects the first ISOC input endpoint as the input
transfer endpoint, however some devices can provide streams on endpoints
different then the first one, so some subdrivers (e.g. gspca_kinect) may
want to select a specific endpoint to use as a transfer endpoint.
Add an xfer_ep field to struct gspca_dev, and change alt_xfer() so that
it accepts a parameter which represents a specific endpoint address to
look for.
If a subdriver wants to specify a value for gspca_dev->xfer_ep it can do
that in its sd_config() callback.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While this device doesn't have a scaler (or have it disabled),
the screen dimentions are a function of the standard. Ok, right
now, only 480 lines standards are implemented, although it
supports other ones. Yet, let's calculate the size, to make
easier to add more standards latter.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It seems that there's a bug at au0828 hardware/firmware
related to alternate setting: when the device is already at
alt 5, a further call causes the URBs to receive -ESHUTDOWN.
I found two different encarnations of this issue:
1) at qv4l2, it fails the second time we try to open the
video screen;
2) at xawtv, when audio underrun occurs, with is very
frequent, at least on my test machine.
The fix is simple: just check if alt=5 before calling
set_usb_interface().
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The analog part of au0828 is missing the tuner Kconfig dependency.
That makes the device to not work while in analog mode.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
The bug happens when:
CONFIG_DVB_DIB8000=m
CONFIG_DVB_USB_DIB0700=y
As a bonus, dib8000 won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with both Pixelview PV-D231 and MyGica S870.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function,
but, on dib8000, there are several exported symbols.
We need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename this function, in order to prepare for
a next patch that will add a new attach() function that
will be the only one exported by this module.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
This were reported several times, like:
drivers/built-in.o: In function `cxusb_dualdig4_rev2_tuner_attach':
>> cxusb.c:(.text+0x27d4b5): undefined reference to `dib7000p_get_i2c_master'
drivers/built-in.o: In function `dib7070_set_param_override':
cxusb.c:(.text+0x27d5a5): undefined reference to `dib0070_wbd_offset'
>> cxusb.c:(.text+0x27d5be): undefined reference to `dib7000p_set_wbd_ref'
drivers/built-in.o: In function `dib7070_tuner_reset':
>> cxusb.c:(.text+0x27d5f9): undefined reference to `dib7000p_set_gpio'
drivers/built-in.o: In function `cxusb_dualdig4_rev2_frontend_attach':
>> cxusb.c:(.text+0x27df5c): undefined reference to `dib7000p_i2c_enumeration'
In this specific report:
CONFIG_DVB_USB_CXUSB=y
CONFIG_DVB_DIB7000P=m
But the same type of bug can happen if:
CONFIG_DVB_DIB7000P=m
and one of the bridge drivers is compiled builtin (cxusb, cx23885-dvb
and/or dib0700).
As a bonus, dib7000p won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with Hauppauge Nova-TD (2 frontends).
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function.
However, the dib7000p initialization can require up to 3
functions to be called:
- dib7000p_get_i2c_master;
- dib7000p_i2c_enumeration;
- dib7000p_init (before this patch dib7000_attach).
(plus a bunch of other functions that the bridge driver will
need to call).
As we need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename the function that probes and init the hardware
to dib7000p_init.
A latter patch will add a new dib7000p_attach that will be
used as originally conceived by dvb_attach() way.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change handling of signal_lock on rs2000. Use ibuf[2] to detect
lock as there is a longer wait for lock to appear in ibuf[6].
Remove last_key and key_timeout and use jiffies plus 60ms
to detect that streaming is still active.
If the current jiffies is time_after the interrupt urb overdue and
clear signal lock.
This results in far faster recovery of lock and streaming.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
