Add enable/disable functions which effectively control the GPT iclk and fclk.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove Remove superfluous/recursive locking for GPIO
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM11 can't access the IVA interrupt controller from
IVA slave port.
From Richard Woodruff:
"The 0x40000000 is an IVA-ARM7 local bus address.
The IVA-INTC is NOT accessible through the IVA-L3-Slave Port.
The current TRM does say this directly and indirectly in a few spots and
in figures."
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After adjusting clock parameters, OMAP2 CPUs need a memory
barrier to make sure the changes go into effect immediately.
Otherwise bad things will happen if we try to access the
peripheral whose clock is just being enabled.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A forgotten parenthesis in clock.c caused the PLL stabilization loop
to not be executed correctly.
Signed-off-by: Samuel Ortiz <samuel.ortiz@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch makes the OMAP2 dmtimers module using the interface
clocks only while the registers are accessed (except GPT1 which has
iclk enabled all the time).
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for assigning memory regions dynamically to peripherals
attached to GPMC interface. Platform specific code should now call
gpmc_cs_request to get a free GPMC memory region instead of using
a fixed address.
Make the H4 and Apollon platform initialization use the new API.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The recent MPUIO range change fix breaks compilation if
CONFIG_ARCH_OMAP24XX isn't defined; it should be OMAP_MAX_GPIO_LINES not
MAX_GPIO_LINES I believe. This one liner fixes it.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds pin mux info for the SPI master/slave interface on
OMAP16xx. Data from OMAP 1611/1612 TRM and errata. Works for me on my
1611/H2 with current git kernel.
Signed-off-by: Mark Howell <mhowell@northlink.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have to make sure that the LCD DMA external destination bit is
cleared by default, otherwise OMAP won't sleep.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- MPUIO doesn't exist on OMAP2
- no error was returned for too big MPUIO numbers
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP does not need sys_ck or sys_clkout. If the devices connected
to McBSP need sys_clkout, they need to request it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Apollon board MMC supports on OMAP2
TODO:
We have to check MMC on H4
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reprogramming takes places before putting the CPU into idle mode if
the dynamic tick option is enabled. The timer is then set to expire
at the next pending timer event. Because some time has already passed
since the last reported jiffy we have to wait less than the time
specified in jiffies.
Also make sure we don't set a load value of 0 whose outcome is
unspecified according to the TRM.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch from Ben Dooks
Do not define set_irq_wake as a real function if
the CONFIG_PM option is not set.
Fixes bug reported by Thomas Gleixner.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dan Williams
commit a6a38a6622 changed the iop321 id to a value that does not work with all platforms. Change the mask to permit bit 11. Tested on an iq80321 600Mhz CRB.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the idle code on the s3c2412 as the default
code is using bits in the CLKCON register that are
no-longer there.
Provide an override for the idle code, and ensure
that the power configuration is set to allow idle
instead of stop or sleep.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
These two machines are identical, and supported
by the SMDK2413 configuration. When MACH_SMDK2413
is selected, we must also select MACH_S3C2413
to allow machine_is_smdk2413() or machine_is_s3c2413()
to work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The IRQ_EINT0 through IRQ_EINT3 handling has changed
on the S3C2412 from the previous SoCs in the range,
and thus we need to add code to handle this.
The changes come about due to these IRQs being
displayed in two different registers, and needing to
be acked and masked in both.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The s3c244x-irq.c code makes the mistake of adding
the same drive to two different sys-classes. This
causes the class lists to become corrupted and the
suspend code to OOPS.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
It turns out we have both SMDK2413 and S3C2413 for
the same board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The ARM926EJ-S CPU has the VFP coprocessor and therefore it should be shown
in the /proc/cpuinfo if CONFIG_VFP is enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
Include linux/irq.h in the nslu2 code in order to avoid the following
compiler error:
CC arch/arm/mach-ixp4xx/nslu2-power.o
arch/arm/mach-ixp4xx/nslu2-power.c: In function 'nslu2_power_init':
arch/arm/mach-ixp4xx/nslu2-power.c:53: warning: implicit declaration of function 'set_irq_type'
arch/arm/mach-ixp4xx/nslu2-power.c:53: error: 'IRQ_TYPE_LEVEL_LOW' undeclared (first use in this function)
arch/arm/mach-ixp4xx/nslu2-power.c:53: error: (Each undeclared identifier is reported only once
arch/arm/mach-ixp4xx/nslu2-power.c:53: error: for each function it appears in.)
arch/arm/mach-ixp4xx/nslu2-power.c:54: error: 'IRQ_TYPE_LEVEL_HIGH' undeclared (first use in this function)
make[5]: *** [arch/arm/mach-ixp4xx/nslu2-power.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Remove the pointless changelog comments from
arch/arm/mach-s3c2410 files, as all this can
be found from the revision control system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
Resolve ARM1136 VIPT non-aliasing cache coherency issues observed when
using ptrace to set breakpoints and cleanup copy_{to,from}_user_page()
while we're here as requested by Russell King because "it's also far
too heavy on non-v6 CPUs".
NOTES:
1. Only access_process_vm() calls copy_{to,from}_user_page().
2. access_process_vm() calls get_user_pages() to pin down the "page".
3. get_user_pages() calls flush_dcache_page(page) which ensures cache
coherency between kernel and userspace mappings of "page". However
flush_dcache_page(page) may not invalidate I-Cache over this range
for all cases, specifically, I-Cache is not invalidated for the VIPT
non-aliasing case. So memory is consistent between kernel and user
space mappings of "page" but I-Cache may still be hot over this
range. IOW, we don't have to worry about flush_cache_page() before
memcpy().
4. Now, for the copy_to_user_page() case, after memcpy(), we must flush
the caches so memory is consistent with kernel cache entries and
invalidate the I-Cache if this mm region is executable. We don't
need to do anything after memcpy() for the copy_from_user_page()
case since kernel cache entries will be invalidated via the same
process above if we access "page" again. The flush_ptrace_access()
function (borrowed from SPARC64 implementation) is added to handle
cache flushing after memcpy() for the copy_to_user_page() case.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The type naming in the s3c24xx dma code is riddled with
typedefs creating _t types, from the code import from 2.4
which is contrary to the current Kernel coding style.
This patch cleans this up, removing the typedefs and
and fixing up the resultant code changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
This adds RTC support to the csb337 default config. Both the AT91
and the ds1307 RTCs are enabled (rtc0 and rtc1 respectively).
The ds1307 is used to initialize the system time, since it's battery-backed.
From then on the AT91 RTC is used, since it's more capable (with both
alarm and update irqs, and system wakeup capability) even though it
needs manual initialization (symlink /dev/rtc to /dev/rtc0 for older
versions of hwclock, then "hwclock --systohc") in an rc script or
from inittab.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
vfp_put_double didn't work in a CONFIG_AEABI kernel. By swapping
the arguments, we arrange for them to be in the same place regardless
of ABI. I made the same change to vfp_put_float for consistency.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
On armv4t systems, we have always compiled the kernel with -march=armv4
instead of -march=armv4t, which means that any use of bx will bomb out.
Commit ba9b5d7637 introduced the use of
bx in the kernel, which means we need to compile with -march=armv4t on
armv4t systems now.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the necessary call to register_isa_ports() so that glibc knows
where these are found on Integrator platforms.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
Remove buld warning when building sa1111 on non-sa1100 platforms (e.g. PXA).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Paul Sokolovsky
This patch adds timeouts while working with SSP registers. Such
timeouts were envisioned by docstrings in ssp.c, but were not
implemented. There were actual lockups while accessing
touchscreen for iPaqs h1910, h4000 due to lack of the timeouts.
This is updated version of previously submitted patch: 3738/1.
Signed-off-by: Paul Sokolovsky <pmiscml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The fcvtds and fcvtsd instructions were generating a qnan bit pattern
for both quiet and signalling NaNs.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The fcvtsd/fcvtds emulation was left behind when the numbering of double
precision registers was changed from 0-30 to 0-15. Both conversion
instructions were writing their results to the wrong register. Also,
the conversion instructions should stop after the first element even
if a vector length is specified.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The recent fix to hide VFP_NAN_FLAG broke the check in vfp_raise_exceptions;
it would attempt to deliver an exception mask of 0xfffffeff instead of reporting
a serious error condition using printk. Define a safe constant to use for
an invalid exception maskm, and use it at both ends.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
The userspace helpers in clean/arch/arm/kernel/entry-armv.S are called
directly in/from userspace. They need to cope with being called from
Thumb code.
Patch below uses the bx interworking instruction when
CONFIG_ARM_THUMB=y.
Based on an earlier patch from Paul Brook <paul@codesourcery.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
This is instead of a magic number.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Kevin Hilman
Previous locking changes to dmabounce incorrectly return non-NULL even
when buffer not found. Fix it up.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
tidy up the makefile by using TABs to indent, and ensure
that all items are indented the same.
Move the DMA to its own section, ready for the next set
of updates
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
A number of small issues with the S3C24XX DMA have
cropped up, which this patch fixes. These are:
- check wether we can load another buff in start
- update state handling in s3c2410_dma_lastxfer
- only reload in irq if channel is not idle
- more informative timeout errors (add source)
- do not call request_irq() with irqs locked
- added waitforstop function
The patch also adds a S3C2410_DMAOP_STARTED for
the occasions when the driver wants to ensure that
the DMA system load state is resynced after loading.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previously the message was "Fatal exception: panic_on_oops", as introduced
in a recent patch whith removed a somewhat dangerous call to ssleep() in
the panic_on_oops path. However, Paul Mackerras suggested that this was
somewhat confusing, leadind people to believe that it was panic_on_oops
that was the root cause of the fatal exception. On his suggestion, this
patch changes the message to simply "Fatal exception". A suitable oops
message should already have been displayed.
Signed-off-by: Simon Horman <horms@verge.net.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
