Builds with EXT4FS_DEBUG defined (to enable ext4_debug()) fail
without these changes. Clean up some format warnings too.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
We need to look at the default value and make sure
the mount options are not set via default value
before showing them via ext4_show_options
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
This patch adds 64-bit inode version support to ext4. The lower 32 bits
are stored in the osd1.linux1.l_i_version field while the high 32 bits
are stored in the i_version_hi field newly created in the ext4_inode.
This field is incremented in case the ext4_inode is large enough. A
i_version mount option has been added to enable the feature.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Kalpak Shah <kalpak@clusterfs.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Jean Noel Cordenner <jean-noel.cordenner@bull.net>
The i_version field of the inode is changed to be a 64-bit counter that
is set on every inode creation and that is incremented every time the
inode data is modified (similarly to the "ctime" time-stamp).
The aim is to fulfill a NFSv4 requirement for rfc3530.
This first part concerns the vfs, it converts the 32-bit i_version in
the generic inode to a 64-bit, a flag is added in the super block in
order to check if the feature is enabled and the i_version is
incremented in the vfs.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Jean Noel Cordenner <jean-noel.cordenner@bull.net>
Signed-off-by: Kalpak Shah <kalpak@clusterfs.com>
The journal checksum feature adds two new flags i.e
JBD2_FEATURE_INCOMPAT_ASYNC_COMMIT and JBD2_FEATURE_COMPAT_CHECKSUM.
JBD2_FEATURE_CHECKSUM flag indicates that the commit block contains the
checksum for the blocks described by the descriptor blocks.
Due to checksums, writing of the commit record no longer needs to be
synchronous. Now commit record can be sent to disk without waiting for
descriptor blocks to be written to disk. This behavior is controlled
using JBD2_FEATURE_ASYNC_COMMIT flag. Older kernels/e2fsck should not be
able to recover the journal with _ASYNC_COMMIT hence it is made
incompat.
The commit header has been extended to hold the checksum along with the
type of the checksum.
For recovery in pass scan checksums are verified to ensure the sanity
and completeness(in case of _ASYNC_COMMIT) of every transaction.
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Girish Shilamkar <girish@clusterfs.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
The patch below updates the jbd stats patch to 2.6.20/jbd2.
The initial patch was posted by Alex Tomas in December 2005
(http://marc.info/?l=linux-ext4&m=113538565128617&w=2).
It provides statistics via procfs such as transaction lifetime and size.
Sometimes, investigating performance problems, i find useful to have
stats from jbd about transaction's lifetime, size, etc. here is a
patch for review and inclusion probably.
for example, stats after creation of 3M files in htree directory:
[root@bob ~]# cat /proc/fs/jbd/sda/history
R/C tid wait run lock flush log hndls block inlog ctime write drop close
R 261 8260 2720 0 0 750 9892 8170 8187
C 259 750 0 4885 1
R 262 20 2200 10 0 770 9836 8170 8187
R 263 30 2200 10 0 3070 9812 8170 8187
R 264 0 5000 10 0 1340 0 0 0
C 261 8240 3212 4957 0
R 265 8260 1470 0 0 4640 9854 8170 8187
R 266 0 5000 10 0 1460 0 0 0
C 262 8210 2989 4868 0
R 267 8230 1490 10 0 4440 9875 8171 8188
R 268 0 5000 10 0 1260 0 0 0
C 263 7710 2937 4908 0
R 269 7730 1470 10 0 3330 9841 8170 8187
R 270 0 5000 10 0 830 0 0 0
C 265 8140 3234 4898 0
C 267 720 0 4849 1
R 271 8630 2740 20 0 740 9819 8170 8187
C 269 800 0 4214 1
R 272 40 2170 10 0 830 9716 8170 8187
R 273 40 2280 0 0 3530 9799 8170 8187
R 274 0 5000 10 0 990 0 0 0
where,
R - line for transaction's life from T_RUNNING to T_FINISHED
C - line for transaction's checkpointing
tid - transaction's id
wait - for how long we were waiting for new transaction to start
(the longest period journal_start() took in this transaction)
run - real transaction's lifetime (from T_RUNNING to T_LOCKED
lock - how long we were waiting for all handles to close
(time the transaction was in T_LOCKED)
flush - how long it took to flush all data (data=ordered)
log - how long it took to write the transaction to the log
hndls - how many handles got to the transaction
block - how many blocks got to the transaction
inlog - how many blocks are written to the log (block + descriptors)
ctime - how long it took to checkpoint the transaction
write - how many blocks have been written during checkpointing
drop - how many blocks have been dropped during checkpointing
close - how many running transactions have been closed to checkpoint this one
all times are in msec.
[root@bob ~]# cat /proc/fs/jbd/sda/info
280 transaction, each upto 8192 blocks
average:
1633ms waiting for transaction
3616ms running transaction
5ms transaction was being locked
1ms flushing data (in ordered mode)
1799ms logging transaction
11781 handles per transaction
5629 blocks per transaction
5641 logged blocks per transaction
Signed-off-by: Johann Lombardi <johann.lombardi@bull.net>
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
When we are overwriting a file and not actually allocating new file system
blocks we need to take only the read lock on i_data_sem.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
We are currently taking the truncate_mutex for every read. This would have
performance impact on large CPU configuration. Convert the lock to read write
semaphore and take read lock when we are trying to read the file.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
When doing a migrate from ext3 to ext4 inode we need to make sure the test
for inode type and walking inode data happens inside lock. To make this
happen move truncate_mutex early before checking the i_flags.
This actually should enable us to remove the verify_chain().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
The unused code found in ext3_find_entry() is also present (and still
unused) in the ext4_find_entry() code. This patch removes it.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Before we start committing a transaction, we call
__journal_clean_checkpoint_list() to cleanup transaction's written-back
buffers.
If this call happens to remove all of them (and there were already some
buffers), __journal_remove_checkpoint() will decide to free the transaction
because it isn't (yet) a committing transaction and soon we fail some
assertion - the transaction really isn't ready to be freed :).
We change the check in __journal_remove_checkpoint() to free only a
transaction in T_FINISHED state. The locking there is subtle though (as
everywhere in JBD ;(). We use j_list_lock to protect the check and a
subsequent call to __journal_drop_transaction() and do the same in the end
of journal_commit_transaction() which is the only place where a transaction
can get to T_FINISHED state.
Probably I'm too paranoid here and such locking is not really necessary -
checkpoint lists are processed only from log_do_checkpoint() where a
transaction must be already committed to be processed or from
__journal_clean_checkpoint_list() where kjournald itself calls it and thus
transaction cannot change state either. Better be safe if something
changes in future...
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When a new block bitmap is read from disk in read_block_bitmap()
there are a few bits that should ALWAYS be set. In particular,
the blocks given corresponding to block bitmap, inode bitmap and inode tables.
Validate the block bitmap against these blocks.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Add buffer head related helper function bh_uptodate_or_lock and
bh_submit_read which can be used by file system
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
ext4 file system was by default ignoring errors and continuing. This
is not a good default as continuing on error could lead to file system
corruption. Change the default to mark the file system
readonly. Debian and ubuntu already does this as the default in their
fstab.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
When mounting an ext4 filesystem with corrupted s_first_data_block, things
can go very wrong and oops.
Because blocks_count in ext4_fill_super is a u64, and we must use do_div,
the calculation of db_count is done differently than on ext4. If
first_data_block is corrupted such that it is larger than ext4_blocks_count,
for example, then the intermediate blocks_count value may go negative,
but sign-extend to a very large value:
blocks_count = (ext4_blocks_count(es) -
le32_to_cpu(es->s_first_data_block) +
EXT4_BLOCKS_PER_GROUP(sb) - 1);
This is then assigned to s_groups_count which is an unsigned long:
sbi->s_groups_count = blocks_count;
This may result in a value of 0xFFFFFFFF which is then used to compute
db_count:
db_count = (sbi->s_groups_count + EXT4_DESC_PER_BLOCK(sb) - 1) /
EXT4_DESC_PER_BLOCK(sb);
and in this case db_count will wind up as 0 because the addition overflows
32 bits. This in turn causes the kmalloc for group_desc to be of 0 size:
sbi->s_group_desc = kmalloc(db_count * sizeof (struct buffer_head *),
GFP_KERNEL);
and eventually in ext4_check_descriptors, dereferencing
sbi->s_group_desc[desc_block] will result in a NULL pointer dereference.
The simplest test seems to be to sanity check s_first_data_block,
EXT4_BLOCKS_PER_GROUP, and ext4_blocks_count values to be sure
their combination won't result in a bad intermediate value for
blocks_count. We could just check for db_count == 0, but
catching it at the root cause seems like it provides more info.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Mingming Cao <cmm@us.ibm.com>
This fix some instances where we were continuing after calling
ext4_error. ext4_error call panic only if errors=panic mount option is
set. So we need to make sure we return correctly after ext4_error call
Reported by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
The max file size for ext3 file system is now calculated
with hardcoded 4K block size. The patch fixes it to be
calculated with the right block size.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
The max file size for ext2 file system is now calculated
with hardcoded 4K block size. The patch fixes it to be
calculated with the right block size.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Calculate & store the max offset for bitmapped files, and
catch too-large seeks, truncates, and writes in ext4, shortening
or rejecting as appropriate.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
This patch converts ext4_inode i_blocks to represent total
blocks occupied by the inode in file system block size.
Earlier the variable used to represent this in 512 byte
block size. This actually limited the total size of the file.
The feature is enabled transparently when we write an inode
whose i_blocks cannot be represnted as 512 byte units in a
48 bit variable.
inode flag EXT4_HUGE_FILE_FL
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Use the __le16 l_i_reserved1 field of the linux2 struct of ext4_inode
to represet the higher 16 bits for i_blocks. With this change max_file
size becomes (2**48 -1 )* 512 bytes.
We add a RO_COMPAT feature to the super block to indicate that inode
have i_blocks represented as a split 48 bits. Super block with this
feature set cannot be mounted read write on a kernel with CONFIG_LSF
disabled.
Super block flag EXT4_FEATURE_RO_COMPAT_HUGE_FILE
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Rename ext4_inode.i_dir_acl to i_size_high
drop ext4_inode_info.i_dir_acl as it is not used
Rename ext4_inode.i_size to ext4_inode.i_size_lo
Add helper function for accessing the ext4_inode combined i_size.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Rename i_file_acl to i_file_acl_lo. This helps
in finding bugs where we use i_file_acl instead
of the combined i_file_acl_lo and i_file_acl_high
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
This patch fixes various places where the group number is set to a negative
value.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
In many places variables for block group are of type int, which limits the
maximum number of block groups to 2^31. Each block group can have up to
2^15 blocks, with a 4K block size, and the max filesystem size is limited to
2^31 * (2^15 * 2^12) = 2^58 -- or 256 PB
This patch introduces a new type ext4_group_t, of type unsigned long, to
represent block group numbers in ext4.
All occurrences of block group variables are converted to type ext4_group_t.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
There are many casts in extents.c which are not needed,
as the variables are already the type of the cast, or
are being promoted for no particular reason in printk's.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
This patch adds a new data type ext4_lblk_t to represent
the logical file blocks.
This is the preparatory patch to support large files in ext4
The follow up patch with convert the ext4_inode i_blocks to
represent the number of blocks in file system block size. This
changes makes it possible to have a block number 2**32 -1 which
will result in overflow if the block number is represented by
signed long. This patch convert all the block number to type
ext4_lblk_t which is typedef to __u32
Also remove dead code ext4_ext_walk_space
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
With 64KB blocksize, a directory entry can have size 64KB which does not fit
into 16 bits we have for entry lenght. So we store 0xffff instead and convert
value when read from / written to disk. The patch also converts some places
to use ext4_next_entry() when we are changing them anyway.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
This patch set supports large block size(>4k, <=64k) in ext4,
just enlarging the block size limit. But it is NOT possible to have 64kB
blocksize on ext4 without some changes to the directory handling
code. The reason is that an empty 64kB directory block would have a
rec_len == (__u16)2^16 == 0, and this would cause an error to be hit in
the filesystem. The proposed solution is treat 64k rec_len
with a an impossible value like rec_len = 0xffff to handle this.
The Patch-set consists of the following 2 patches.
[1/2] ext4: enlarge blocksize
- Allow blocksize up to pagesize
[2/2] ext4: fix rec_len overflow
- prevent rec_len from overflow with 64KB blocksize
Now on 64k page ppc64 box runs with this patch set we could create a 64k
block size ext4dev, and able to handle empty directory block.
Signed-off-by: Takashi Sato <sho@tnes.nec.co.jp>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
The userspace ABI of ocfs2's internal cluster stack (o2cb) was broken by
commit c60b717879 "kset: convert ocfs2 to
use kset_create". Specifically, the '/sys/o2cb' kset was moved to
'/sys/fs/o2cb'. This breaks all ocfs2 tools and renders the
filesystem unmountable.
This fix moves '/sys/o2cb' back where it belongs.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Create a specific helper for netlink kernel socket disposal. This just
let the code look better and provides a ground for proper disposal
inside a namespace.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Tested-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
cat /proc/net/atm/arp causes the NULL pointer dereference in the
get_proc_net+0xc/0x3a. This happens as proc_get_net believes that the
parent proc dir entry contains struct net.
Fix this assumption for "net/atm" case.
The problem is introduced by the commit c0097b07abf5f92ab135d024dd41bd2aada1512f
from Eric W. Biederman/Daniel Lezcano.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow caller to pass in a release function, there might be
other resources that need releasing as well. Needed for
network receive.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the deprecated __attribute_used__.
[Introduce __section in a few places to silence checkpatch /sam]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Remove dead code in smbfs makefile.
Cc: Al Viro <viro@www.linux.org.uk>
Cc: Tim Shimmin <xfs-masters@oss.sgi.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Currently you must be root to set idle io prio class on a process. This
is due to the fact that the idle class is implemented as a true idle
class, meaning that it will not make progress if someone else is
requesting disk access. Unfortunately this means that it opens DOS
opportunities by locking down file system resources, hence it is root
only at the moment.
This patch relaxes the idle class a little, by removing the truly idle
part (which entals a grace period with associated timer). The
modifications make the idle class as close to zero impact as can be done
while still guarenteeing progress. This means we can relax the root only
criteria as well.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If the users sets a new ->bi_bdev on the bio after __bio_clone() has
returned it, the "segment counts valid" flag still remains even though
it may be different with the new target. So don't calculate segment
counts in __bio_clone().
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] DFS build fixes
[CIFS] DFS support: provide shrinkable mounts
[CIFS] Do not log path names in lookup errors
[CIFS] DFS support patchset: Added mountdata
[CIFS] Forgot to add two new files from previous commit
[CIFS] DNS name resolution helper upcall for cifs
[CIFS] fix checkpatch warnings in fs/cifs/inode.c
[CIFS] hold ses sem on tcp session reconnect during mount
[CIFS] Allow setting mode via cifs acl
[CIFS] fix unicode string alignment in SPNEGO setup
[CIFS] cifs_partialpagewrite() cleanup
[CIFS] use krb5 session key from first SMB session after a NegProt
[CIFS] redo existing session setup if needed in cifs_mount
[CIFS] Only dump SPNEGO key if CONFIG_CIFS_DEBUG2 is set
[CIFS] fix SetEA failure to some Samba versions
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
If we know a buffer_head is non-null, then brelse() is unnecessary and
put_bh() can be used instead. Also, an explicit check for NULL is
unnecessary when using brelse(). This patch only covers buffer_head_io.c and
resize.c, which have recently added code which exhibits this problem.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
ocfs2_super->blocked_lock_list and ocfs2_super->blocked_lock_count have some
usage restrictions which aren't immediately obvious to anyone reading the
code. It's a good idea to document this so that we avoid making costly
mistakes in the future.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
configfs has been alive and kicking for a while now. It underpins some
non-EXPERIMENTAL subsystems, such as OCFS2's cluster stack.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Bump the printed version to 1.5.0. This helps us quickly identify which
version of Ocfs2 a bug filer is running.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Currently the process of dlm join contains 2 steps: query join and assert join.
After query join, the joined node will set its joining_node. So if the joining
node happens to panic before the 2nd step, the joined node will fail to clear
its joining_node flag because that node isn't in the domain map. It at least
cause 2 problems.
1. All the new join request will fail. So no new node can mount the volume.
2. The joined node can't umount the volume since during the umount process it
has to wait for the joining_node to be unknown. So the umount will be hanged.
The solution is to clear the joining_node before we check the domain map.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Convert byte order of constant instead of variable it will be done at
compile time vs run time. Remove unused le32_and_cpu.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Lots of people are having trouble with the default timeouts, which are too
low. These new values are derived from an informal survey taken on
ocfs2-users, as well as data from bug reports. This should reduce the amount
of cluster disconnects and subsequent fencing seen during normal workloads.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Explicitely convert loff_t to long long in printf. Just for sure...
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
We should use generic_file_llseek() and not default_llseek() so that
s_maxbytes gets properly checked when seeking.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
In ocfs2_read_inline_data() we should store file size in loff_t. Although
the file size should fit in 32 bits we cannot be sure in case filesystem is
corrupted.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Create separate lockdep lock classes for system file's i_mutexes. They are
used to guard allocations and similar things and thus rank differently
than i_mutex of a regular file or directory.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Hook up ocfs2_flock(), using the new flock lock type in dlmglue.c. A new
mount option, "localflocks" is added so that users can revert to old
functionality as need be.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
This adds a new dlmglue lock type which is intended to back flock()
requests.
Since these locks are driven from userspace, usage rules are much more
liberal than the typical Ocfs2 internal cluster lock. As a result, we can't
make use of most dlmglue features - lock caching and lock level
optimizations in particular. Additionally, userspace is free to deadlock
itself, so we have to deal with that in the same way as the rest of the
kernel - by allowing a signal to abort a lock request.
In order to keep ocfs2_cluster_lock() complexity down, ocfs2_file_lock()
does it's own dlm coordination. We still use the same helper functions
though, so duplicated code is kept to a minimum.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Local alloc is a performance optimization in ocfs2 in which a node
takes a window of bits from the global bitmap and then uses that for
all small local allocations. This window size is fixed to 8MB currently.
This patch allows users to specify the window size in MB including
disabling it by passing in 0. If the number specified is too large,
the fs will use the default value of 8MB.
mount -o localalloc=X /dev/sdX /mntpoint
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mostly taken from ext3. This allows the user to set the jbd commit interval,
in seconds. The default of 5 seconds stays the same, but now users can
easily increase the commit interval. Typically, this would be increased in
order to benefit performance at the expense of data-safety.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Check that an online resize is being driven by a user with permission to
change system resource limits.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
This patch adds the ability for a userspace program to request that a
properly formatted cluster group be added to the main allocation bitmap for
an Ocfs2 file system. The request is made via an ioctl, OCFS2_IOC_GROUP_ADD.
On a high level, this is similar to ext3, but we use a different ioctl as
the structure which has to be passed through is different.
During an online resize, tunefs.ocfs2 will format any new cluster groups
which must be added to complete the resize, and call OCFS2_IOC_GROUP_ADD on
each one. Kernel verifies that the core cluster group information is valid
and then does the work of linking it into the global allocation bitmap.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
This patch adds the ability for a userspace program to request an extend of
last cluster group on an Ocfs2 file system. The request is made via ioctl,
OCFS2_IOC_GROUP_EXTEND. This is derived from EXT3_IOC_GROUP_EXTEND, but is
obviously Ocfs2 specific.
tunefs.ocfs2 would call this for an online-resize operation if the last
cluster group isn't full.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
This value is initialized from global_bitmap->id2.i_chain.cl_cpg. If there
is only 1 group, it will be equal to the total clusters in the volume. So
as for online resize, it should change for all the nodes in the cluster.
It isn't easy and there is no corresponding lock for it.
bitmap_cpg is only used in 2 areas:
1. Check whether the suballoc is too large for us to allocate from the global
bitmap, so it is little used. And now the suballoc size is 2048, it rarely
meet this situation and the check is almost useless.
2. Calculate which group a cluster belongs to. We use it during truncate to
figure out which cluster group an extent belongs too. But we should be OK
if we increase it though as the cluster group calculated shouldn't change
and we only ever have a small bitmap_cpg on file systems with a single
cluster group.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Remove 'readpages' from the list in ocfs2.txt. Instead of having two
identical lists, I just removed the list in the OCFS2 section of fs/Kconfig
and added a pointer to Documentation/filesystems/ocfs2.txt.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Add ->readpages support to Ocfs2. This is rather trivial - all it required
is a small update to ocfs2_get_block (for mapping full extents via b_size)
and an ocfs2_readpages() function which partially mirrors ocfs2_readpage().
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Call this the "inode_lock" now, since it covers both data and meta data.
This patch makes no functional changes.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The meta lock now covers both meta data and data, so this just removes the
now-redundant data lock.
Combining locks saves us a round of lock mastery per inode and one less lock
to ping between nodes during read/write.
We don't lose much - since meta locks were always held before a data lock
(and at the same level) ordered writeout mode (the default) ensured that
flushing for the meta data lock also pushed out data anyways.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
In order to extend inode lock coverage to inode data, we use the same data
downconvert worker with only a small modification to only do work for
regular files.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The node maps that are set/unset by these votes are no longer relevant, thus
we can remove the mount and umount votes. Since those are the last two
remaining votes, we can also remove the entire vote infrastructure.
The vote thread has been renamed to the downconvert thread, and the small
amount of functionality related to managing it has been moved into
fs/ocfs2/dlmglue.c. All references to votes have been removed or updated.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Now that the dlm exposes domain information to us, we don't need generic
node up / node down callbacks. And since the DLM is only telling us when a
node goes down unexpectedly, we no longer need to optimize away node down
callbacks via the umount map.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
With this, a dlm client can take advantage of the group protocol in the dlm
to get full notification whenever a node within the dlm domain leaves
unexpectedly.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched: (96 commits)
sched: keep total / count stats in addition to the max for
sched, futex: detach sched.h and futex.h
sched: fix: don't take a mutex from interrupt context
sched: print backtrace of running tasks too
printk: use ktime_get()
softlockup: fix signedness
sched: latencytop support
sched: fix goto retry in pick_next_task_rt()
timers: don't #error on higher HZ values
sched: monitor clock underflows in /proc/sched_debug
sched: fix rq->clock warps on frequency changes
sched: fix, always create kernel threads with normal priority
debug: clean up kernel/profile.c
sched: remove the !PREEMPT_BKL code
sched: make PREEMPT_BKL the default
debug: track and print last unloaded module in the oops trace
debug: show being-loaded/being-unloaded indicator for modules
sched: rt-watchdog: fix .rlim_max = RLIM_INFINITY
sched: rt-group: reduce rescheduling
hrtimer: unlock hrtimer_wakeup
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6:
mount options: fix jfs
JFS: simplify types to get rid of sparse warning
JFS: FIx one more plain integer as NULL pointer warning
JFS: Remove defconfig ptr comparison to 0
JFS: use DIV_ROUND_UP where appropriate
Remove unnecessary kmalloc casts in the jfs filesystem
JFS is missing a memory barrier
JFS: Make sure special inode data is written after journal is flushed
JFS: clear PAGECACHE_TAG_DIRTY for no-write pages
LatencyTOP kernel infrastructure; it measures latencies in the
scheduler and tracks it system wide and per process.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch implements a new version of RCU which allows its read-side
critical sections to be preempted. It uses a set of counter pairs
to keep track of the read-side critical sections and flips them
when all tasks exit read-side critical section. The details
of this implementation can be found in this paper -
http://www.rdrop.com/users/paulmck/RCU/OLSrtRCU.2006.08.11a.pdf
and the article-
http://lwn.net/Articles/253651/
This patch was developed as a part of the -rt kernel development and
meant to provide better latencies when read-side critical sections of
RCU don't disable preemption. As a consequence of keeping track of RCU
readers, the readers have a slight overhead (optimizations in the paper).
This implementation co-exists with the "classic" RCU implementations
and can be switched to at compiler.
Also includes RCU tracing summarized in debugfs.
[ akpm@linux-foundation.org: build fixes on non-preempt architectures ]
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Reviewed-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
selinux: make mls_compute_sid always polyinstantiate
security/selinux: constify function pointer tables and fields
security: add a secctx_to_secid() hook
security: call security_file_permission from rw_verify_area
security: remove security_sb_post_mountroot hook
Security: remove security.h include from mm.h
Security: remove security_file_mmap hook sparse-warnings (NULL as 0).
Security: add get, set, and cloning of superblock security information
security/selinux: Add missing "space"
This patch allows gfs2 to perform journal recovery even if it is mounted
read-only. Strictly speaking, a read-only mount should not be writing to
the filesystem, but we do this only to perform journal recovery. A
read-only mount will fail if we don't recover the dirty journal. Also,
when gfs2 is used as a root filesystem, it will be mounted read-only
before being mounted read-write during the boot sequence. A failed
read-only mount will panic the machine during bootup.
Signed-off-by: Abhijith Das <adas@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
I spotted this bug while I was digging around. Looks like it could cause
a lockup in some rare error condition.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
There was a bug in the truncation/invalidation race path for
->page_mkwrite for gfs2. It ought to return 0 so that the effect is the
same as if the page was truncated at any of the other points at which
the page_lock is dropped. This will result in the restart of the whole
page fault path. If it was due to a real truncation (as opposed to an
invalidate because we let a glock go) then the ->fault path will pick
that up when it gets called again.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch fixes a minor typo. Surprisingly, it still compiled.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This is a small I/O performance enhancement to gfs2. (Actually, it is a rework of
an earlier version I got wrong). The idea here is to check if the write extends
past the last block in the file. If so, the function can save itself a lot of
time and trouble because it knows an allocate will be required. Benchmarks like
iozone should see better performance.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch removes a vestigial variable "i_spin" from the gfs2_inode
structure. This not only saves us memory (>300000 of these in memory
for the oom test) it also saves us time because we don't have to
spend time initializing it (i.e. slightly better performance).
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
It is possible to reduce the size of GFS2 inodes by taking the i_alloc
structure out of the gfs2_inode. This patch allocates the i_alloc
structure whenever its needed, and frees it afterward. This decreases
the amount of low memory we use at the expense of requiring a memory
allocation for each page or partial page that we write. A quick test
with postmark shows that the overhead is not measurable and I also note
that OCFS2 use the same approach.
In the future I'd like to solve the problem by shrinking down the size
of the members of the i_alloc structure, but for now, this reduces the
immediate problem of using too much low-memory on x86 and doesn't add
too much overhead.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Although the values were all being calculated correctly, there was a
race in the assert due to the way it was using atomic variables. This
changes the value we assert on so that we get the same effect by testing
a different variable. This prevents the assert triggering when it shouldn't.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch fixes a couple of problems which affected the execution of files
on GFS2. The first is that there was a corner case where inodes were not
always uptodate at the point at which permissions checks were being carried
out, this was resulting in refusal of execute permission, but only on the
first lookup, subsequent requests worked correctly. The second was a problem
relating to incorrect updating of file sizes which was introduced with the
write_begin/end code for GFS2 a little while back.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Abhijith Das <adas@redhat.com>
Here is a patch for the latest upstream GFS2 code:
The journal extent map needs to be initialized sooner than it
currently is. Otherwise failed mount attempts (e.g. not enough
journals, etc.) may panic trying to access the uninitialized list.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
To improve performance on NUMA, we use the VM's standard page
migration for writeback and ordered pages. Probably we could
also do the same for journaled data, but that would need a
careful audit of the code, so will be the subject of a later
patch.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This is a small correction to my previously posted patch1.
It just changes a divide to a shift. It's faster and doesn't
introduce odd dependencies on 32-bit compiles.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch eliminates the unneeded sd_statfs_mutex mutex but preserves
the ordering as discussed.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch optimizes function gfs2_meta_read. Basically, gfs2_meta_wait
was being called regardless of whether a disk read was requested.
This just pulls that wait into the if that triggers the read.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Function gfs2_block_map was often looking up the disk inode twice.
This optimizes it so that only does it once.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch optimizes the function gfs2_glmutex_lock.
The basic theory is: Why bother initializing a holder, setting up
wait bits and then waiting on them, if you know the glock can be
yours. So the holder stuff is placed inside the if checking if the
glock is locked. This one needs careful scrutiny because changing
anything to do with locking should strike terror into one's heart.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
I eliminated the passing of an unused parameter into gfs2_bitfit called rgd.
This also changes the gfs2_bitfit code that searches for free (or used) blocks.
Before, the code was trying to check for bytes that indicated 4 blocks in
the undesired state. The problem is, it was spending more time trying to
do this than it actually was saving. This version only optimizes the case
where we're looking for free blocks, and it checks a machine word at a time.
So on 32-bit machines, it will check 32-bits (16 blocks) and on 64-bit
machines, it will check 64-bits (32 blocks) at a time. The compiler
optimizes that quite well and we save some time, especially when running
through full bitmaps (like the bitmaps allocated for the journals).
There's probably a more elegant or optimized way to do this, but I haven't
thought of it yet. I'm open to suggestions.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This just eliminates an unused variable from the quota code.
Not likely to be a time saver.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch saves a little time when gfs2 writes to the journals by
keeping a mapping between logical and physical blocks on disk.
That's better than constantly looking up indirect pointers in
buffers, when the journals are several levels of indirection
(which they typically are).
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch is just a cleanup. Function gfs2_get_block() just calls
function gfs2_block_map reversing the last two parameters. By
reversing the parameters, gfs2_block_map() may be called directly
and function gfs2_get_block may be eliminated altogether.
Since this function is done for every block operation,
this streamlines the code and makes it a little bit more efficient.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The fl_owner is that of lockd when posix locks arrive from nfs
clients, so it can't be used to distinguish between lock holders.
Use fl_pid as owner instead; it's the pid of the process on the
nfs client.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
A certain scenario in the rename code path triggers a kernel BUG()
because it accidentally does recursive locking The first lock is
requested to unlink an already existing inode (replacing a file) and the
second lock is requested when the destination directory needs to alloc
some space. It is rare that these two
events happen during the same rename call, and even more rare that these
two instances try to lock the same rgrp. It is, however, possible.
https://bugzilla.redhat.com/show_bug.cgi?id=404711
Signed-off-by: Abhijith Das <adas@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
GFS2 supports two modes of locking - lock_nolock for single node filesystem
and lock_dlm for cluster mode locking. The gfs2 lock methods are removed from
file operation table for lock_nolock protocol. This would allow VFS to handle
posix lock and flock logics just like other in-tree filesystems without
duplication.
Signed-off-by: S. Wendy Cheng <wcheng@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Hi Steven,
Steven Whitehouse wrote:
> Hi,
>
> Now in the -nmw git tree. Thanks,
>
> Steve.
>
> On Wed, 2007-11-21 at 11:54 -0600, Ryan O'Hara wrote:
this patch introduces a bunch of build warnings by leaving around
struct inode *inode = &ip->i_inode;
The patch in attachment cleans them up. Please apply.
Signed-off-by: Fabio Massimo Di Nitto <fabbione@ubuntu.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Remove read/write permission() checks from xattr operations.
VFS layer is already handling permission for xattrs via the
xattr_permission() call, so there is no need for gfs2 to
check permissions. Futhermore, using permission() for SELinux
xattrs ops is incorrect.
Signed-off-by: Ryan O'Hara <rohara@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The issue is indeed UP vs SMP and it is totally random.
spin_is_locked() is a bad assertion because there is no correct answer on UP.
on UP spin_is_locked() has to return either one value or another, always.
This means that in my setup I am lucky enough to trigger the issue and your you
are lucky enough not to.
the patch in attachment removes the bogus calls to BUG_ON and according to David
(in CC and thanks for the long explanation on the problem) we can rely upon
things like lockdep to find problem that might be trying to catch.
Signed-off-by: Fabio M. Di Nitto <fabbione@ubuntu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Print error with log_error() to be consistent with others.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Fabio M. Di Nitto <fabbione@ubuntu.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The patch is a fix to abort mount if the mount.gfs* and possible
umount.* are missing from /sbin.
While we do what we can to guarantee that they are installed properly in
userland (CVS HEAD), we want to make sure that mount still aborts properly.
The only sign of missing helpers is that lock_dlm will receive no mount options
at all. According to David the problem does not exist for lock_nolock as the
helpers are not required.
The patch has been tested for both gfs and gfs2 and it works as expected. The
lack of mount.gfs* will generate an error that is propagated to mount:
oot@node1:~# mount -t gfs2 /dev/nbd2 /mnt/
mount: wrong fs type, bad option, bad superblock on /dev/nbd2,
missing codepage or helper program, or other error
In some cases useful info is found in syslog - try
dmesg | tail or so
[ 3513.303346] GFS2: fsid=: Trying to join cluster "lock_dlm", "gutsy:gfs2"
[ 3513.304546] DLM/GFS2/GFS ERROR: (u)mount helpers are not installed properly!
[ 3513.306290] GFS2: fsid=: can't mount proto=lock_dlm, table=gutsy:gfs2, hostdata=
You might want to notice that it will also avoid mount to hang or fail silently
or with strange errors that will require the cluster to reboot/restart before
you can actually mount the filesystem again.
Signed-off-by: Fabio M. Di Nitto <fabbione@ubuntu.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
We only care about the content of the jindex in two cases,
one is when we mount the fs and the other is when we need
to recover another journal. In both cases we have to update
the jindex anyway, so there is no point in updating it
periodically between times, so this removes it to simplify
gfs2_logd.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch changes the counter which keeps track of the free
blocks in the journal to an atomic_t in preparation for the
following patch which will update the log reservation code.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The only reason for adding glocks to the journal was to keep track
of which locks required a log flush prior to release. We add a
flag to the glock to allow this check to be made in a simpler way.
This reduces the size of a glock (by 12 bytes on i386, 24 on x86_64)
and means that we can avoid extra work during the journal flush.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Use wait_event_interruptible() in the lock_dlm thread instead
of an open coded equivalent, and include a kthread_should_stop()
check in the wait test so we don't miss a kthread_stop().
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch changes the /sys/fs/gfs2/<s_id>/id file to give the device
id "major:minor" rather than the s_id. That enables gfs2_tool to
match devices properly (by id, not name) when locating the tuning files.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The HIF_MUTEX and HIF_PROMOTE flags were set on the glock holders
depending upon which of the two waiters lists they were going to
be queued upon. They were then tested when the holders were taken
off the lists to ensure that the right type of holder was being
dequeued.
Since we are already using separate lists, there doesn't seem a
lot of point having these flags as well, and since setting them
and testing them is in the fast path for locking and unlocking
glock, this patch removes them.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Previously we were doing (write data, wait for data, write metadata, wait
for metadata). After this patch we so (write metadata, write data, wait for
data, wait for metadata) which should be more efficient.
Also I noticed that the drop_bh and xmote_bh functions were almost
identical. In fact the only difference was a single test, and that
test is such that in the drop_bh case, it would always evaluate to
the correct result. As such we can use the xmote_bh functions in
all the places where we were using the drop_bh function and remove
the drop_bh functions.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This call to reclaim glocks is not needed, and in particular we don't want it
in the fast path for locking glocks. The limit was entirely arbitrary anyway
and we can't expect users to adjust things like this, the remaining code will
do the right thing on its own.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Something changed in the upstream kernel, and it needs this
one-liner to allow ops_address.c to build.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This is an addendum to the new AOPs work which moves the point
at which we take the page lock so that we don't get it until
the last possible moment. This resolves a conflict between
starting transactions and the page lock.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch resolves a lock ordering issue where we had been getting
a transaction lock in the wrong order with respect to the page lock.
By using writepages rather than just writepage, it is then possible
to start a transaction before locking the page, and thus matching the
locking order elsewhere in the code.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch splits gfs2_writepage into separate functions for each of
the three cases: writeback, ordered and journalled. As a result
it becomes a lot easier to see what each one is doing. The common
code is moved into gfs2_writepage_common.
This fixes a performance bug where we were doing more work than
strictly required in the ordered write case.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Just like ext3 we now have three sets of address space operations
to cover the cases of writeback, ordered and journalled data
writes. This means that the individual operations can now become
less complicated as we are able to remove some of the tests for
file data mode from the code.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This adds a function "gfs2_is_writeback()" along the lines of the
existing "gfs2_is_jdata()" in order to clean up the code and make
the various tests for the inode mode more obvious. It also fixes
the PageChecked() logic where we were resetting the flag too early
in the case of an error path.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The i_cache was designed to keep references to the indirect blocks
used during block mapping so that they didn't have to be looked
up continually. The idea failed because there are too many places
where the i_cache needs to be freed, and this has in the past been
the cause of many bugs.
In addition there was no performance benefit being gained since the
disk blocks in question were cached anyway. So this patch removes
it in order to simplify the code to prepare for other changes which
would otherwise have had to add further support for this feature.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This cleans up the mmap() code path for GFS2 by implementing the
page_mkwrite function for GFS2. We are thus able to use the
generic filemap_fault function for our ->fault() implementation.
This now means that shared writable mappings will be much more
efficiently shared across the cluster if there is a reasonable
proportion of read activity (the greater proportion, the better).
As a side effect, it also reduces the size of the code, removes
special cases from readpage and readpages, and makes the code
path easier to follow.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
As requested by Christoph, this patch cleans up GFS2's internal
read function so that it no longer uses the do_generic_mapping_read
function. This function is obsolete and GFS2 is the last user of it.
As a side effect the internal read code gets smaller and easier
to read and gfs2_readpage is split into two. One function has the locking
and the other function has the rest of the logic.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Fix a race condition where multiple glock demote requests are sent to
a node back-to-back. This patch does a check inside handle_callback()
to see whether a demote request is in progress. If true, it sets a flag
to make sure run_queue() will loop again to handle the new request,
instead of erronously setting gl_demote_state to a different state.
Signed-off-by: S. Wendy Cheng <wcheng@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
There is no need for kobject_unregister() anymore, thanks to Kay's
kobject cleanup changes, so replace all instances of it with
kobject_put().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the old kobject_init() function is gone, rename
kobject_init_ng() to kobject_init() to clean up the namespace.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the block devices to /sys/class/block. It will create a
flat list of all block devices, with the disks and partitions in one
directory. For compatibility /sys/block is created and contains symlinks
to the disks.
/sys/class/block
|-- sda -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda
|-- sda1 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda1
|-- sda10 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda10
|-- sda5 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda5
|-- sda6 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda6
|-- sda7 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda7
|-- sda8 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda8
|-- sda9 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda9
`-- sr0 -> ../../devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/block/sr0
/sys/block/
|-- sda -> ../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda
`-- sr0 -> ../devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/block/sr0
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the code to use the new kobject functions, cleaning up the
logic in doing so.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop using kobject_register, as this way we can control the sending of
the uevent properly, after everything is properly initialized.
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using a kset for this trivial directory is an overkill.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mike Halcrow <mhalcrow@us.ibm.com>
Cc: Phillip Hellewell <phillip@hellewell.homeip.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kernel_kset does not need to be a kset, but a much simpler kobject now
that we have kobj_attributes.
We also rename kernel_kset to kernel_kobj to catch all users of this
symbol with a build error instead of an easy-to-ignore build warning.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
