We will be registering and unregistering the soc_camera_platform platform
device multiple times, therefore we need a .release() method and have to
nullify the kobj.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a struct device pointer to struct soc_camera_platform_info and let the user
(ap325rxa) pass it down to soc_camera_platform.c in its .add_device() method.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_camera_platform.c is only used by y SuperH ap325rxa board. This patch
converts soc_camera_platform.c and its users for the soc-camera platform-
device conversion and also extends soc-camera core to handle non-I2C cameras.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch to using both register sets - side A and side B for display panning.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch prevents the USB1 interrupt from remaining asserted
immediately after re-boot or during a jump in to a secondary kernel.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This board doesn't use trapped I/O for anything, so just kill off the
select. This was causing problems in the unhandled page fault die path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the kfr2r09 board code so it compiles if CONFIG_I2C=n.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add USB gadget support for port CN26 on the Solution Engine 7724
board. The r8a66597-udc driver is hooked up as a platform device
and some registers are configured to enable the USB in gadget mode.
The hardware driving the USB port is the on-chip USB1 block in
the sh7724 processor configured as USB gadget controller.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add USB gadget support for port YC301 on the KFR2R09 board.
The r8a66597-udc driver is hooked up as a platform device,
clocks are enabled via I2C and some registers are configured
to enable the USB in gadget mode. The hardware driving the
USB port is the on-chip USB0 block in the sh7724 processor
configured as USB gadget controller.
This board is using external hardware to detect USB hotplug
events and allows the processor to dynamically start and stop
clocks. This well thought out hardware feature is unused at
this point and plug and play is unfortunately unsupported.
To properly support all hardware features the USB gadget
stack may need some adjustment.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the EcoVec board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch simply adds LCDC hwblk_id data for the kfr2r09 board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the Solution Engine 7724 board code to use
in-SoC KEYSC resources for the keyboard platform device. Using
the in-SoC key scan controller fixes a crash-during-resume issue.
Without this patch the KEYSC hardware block located in the board
specific FPGA is used together with an external IRQ which is
routed through the FPGA and handled by some board specific demux
code. This board specific FPGA interrupt code does not implement
desc->set_wake() so the enable_irq_wake() call in the sh_keysc
driver will fail at suspend-to-ram time and the disable_irq_wake()
will bomb out when resuming.
Changing the platform data to use the in-SoC KEYSC hardware makes
the se7724 board support code less special which is a good thing.
Also, the board specific KEYSC pin setup code selects in-SoC pin
functions already which makes the current FPGA platform device data
look like a typo.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the AP325RXA board code to register devices at
arch_initcall() time instead of device_initcall(). This
fix unbreaks pcf8563 RTC driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the Migo-R board code to register devices at
arch_initcall() time instead of __initcall(). This fix
unbreaks migor_ts touch screen driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for LED9, LED10 and LED11 on
the Solution Engine 7724 board. If CONFIG_PM is enabled
then these LEDs are used to show the hardware sleep
mode used by the processor. Useful to debug cpuidle.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the NAND flash chip
attached to CS4 on the KFR2R09 board. The device is
driven by the platform device driver "onenand-flash".
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the WQVGA LCD display used by
the KFR2R09 board. The LCD module is a TX07D34VM0AAA made
by Hitachi, and this module is made up by a R61517 chip
together with a 240x400 pixel display. The screen is
attached to the SuperH Mobile LCDC using a 18-bit SYS bus.
The register settings used by the SYS panel setup code are
based on an out-of-tree driver which apart from duplicating
all LCDC driver code and writing to non-existing hardware
registers also never was posted for upstream merge.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Solution Engine 7724 board specific
on-chip sh7724 platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to kfr2r09 board specific on-chip sh7724
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to AP325RXA board specific on-chip sh7723
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Solution Engine 7722 board specific
on-chip sh7722 platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Migo-R board specific on-chip sh7722
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was no big meaning in the support of SVGA,
but 720p support is necessary for ms7724se board.
So, this patch support 720p instead of SVGA.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds KEYSC keypad support to the kfr2r09 board.
The keys driven by the sh7724 on-chip KEYSC block are
described as a platform device and platform data for
the sh_keysc driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds NOR flash support to the kfr2r09 board.
NOR flash support is added by describing the NOR flash
chip hooked up to CS0 as platform device data for the
physmap-flash MTD driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic kfr2r09 board support. Only
the SCIF1 console is supported with this patch, but
this patch and a proper sh7724 configuration is all
that is needed. Combine with an initramfs to have a
small RAM based kernel and distribution booted as
zImage from RAM via JTAG.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the m66592-udc driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_BUILT_IN_M66592 ugliness.
This makes the code cleaner and also allows us to support
both external and internal m66592 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip m66592 without modifying the Kconfig.
The patch adds a m66592 header file for platform data
and ties in platform data to the existing m66592 devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the r8a66597-hcd driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_ON_CHIP_R8A66597 ugliness.
This makes the code cleaner and also allows us to support
both external and internal r8a66597 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip r8a66597 without modifying the Kconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add USB host support for port CN27 on the Solution Engine 7724
board. The r8a66597-hcd driver is hooked up as a platform device
and some registers are configured to enable the USB host function.
The hardware driving the USB port is the on-chip USB0 block in
the sh7724 processor configured as USB host controller.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use "ceu0" and "ceu1" as CEU names instead of "ceu".
This fixes "memchunk" kernel command line selection
on the solution engine 7724 board.
With this patch applied use "memchunk.ceu0=1m" or
"memchunk.ceu1=1m" on kernel command line to override
physically memory size to one meg for CEU0 or CEU1.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds initial support for the PCI-Express module in the SH7786,
particularly as it relates to the urquell platform. Presently it is
only supported in root complex mode, with endpoint mode still requiring
more debugging. 29/32-bit mode and lane configurations are selectable via
board mode pins, and are otherwise fixed.
Only 4x and 1x PCI channels are presently handled, the PCI bridge still
requires additional debugging and stabilization in hardware.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Unify i2c camera device platform data to point to struct soc_camera_link
for a smooth transition to soc-camera as a platform driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Clock function was changed, but highlander used old function.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the LAN9118 ethernet on rsk7203.
The LAN9118 controller is hooked up using a 16-bit data bus,
but the rsk7203 board does not swap the byte lanes as needed
between the sh7203 processor and the the ethernet controller.
In the processor the CS memory window is configured in 16-bit
mode but the smsc911x driver is told to do 32-bit accesses to
improve performance. The SMSC911X_SWAP_FIFO flag is used
to tell the driver to do software byte swapping of fifo data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Urquell has a system FPGA capable of reading the mode pin states from
software, wire this up in the machvec.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds mode pin configuration and
a machvec structure to Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the mode pin code to keep the pin
definitions in one place. The mode pins values are now
the value of the bit instead of bit number.
With this patch in place the sh7785 header file contains
mode pin comments. The sh7785 clock code and the sh7785lcr
board code are updated to reflect the new shared mode pins.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds mode pin support to the sh7785lcr board.
The harware allows the user to control the mode pins using
dip switches S1 and S2, but from the software the pins are
fixed to the factory default since we have no way to reading
out this configuration from software.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the ms7724se solution engine board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the ap325rxa ncm03j camera code to handle
the case where no i2c driver is present. Without this fix
i2c_transfer() may be passed NULL as adapter which results
in a crash.
Triggered when i2c-sh_mobile.c failed to probe() due to
missing MSTP clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This updates the SH7785 CPU code as well as the SH7785LCR board support
code for making use of the newly refactored clock framework. Support for
the legacy CPG clocks is dropped at this point, with the extal frequency
fed in from the board code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves out the cayman-specific panic handler code to a better
location, and leaves the generic implementation a simple stub that is
still used under emulation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the sh03 rtc code off of using the global rtc_lock and on
to its own spinlock. There are no other possible users of the rtc_lock,
so serializing with it is not necessary.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is special-cased for early initialization. While there are
situations where these static early initializations are still necessary,
with minor changes it is possible to use this for the regular ioremap
implementation as well. This allows us to kill off the special-casing for
the remap completely and to start tidying up all of the SH-5
special-casing in drivers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All 32-bit SuperH processors currently go through __ioremap_mode()
and check for IO_TRAPPED and directly mapped segments. With this
patch we simplify the MMU less case with a pass through version of
__ioremap_mode() which just returns the physical address.
The effects of this is change are:
- fix non-MMU ioremap() of high address hardware blocks (sh7203 CMT)
- make sure IO_TRAPPED is not selected
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The RTS7751R2D_1 boards only support 1MB of socket-mounted MBM29F040
flash, which we just leave alone as it's not terribly interesting.
This adds support for the s29gl256p on the r2d+ boards that makes a bit
more sense to expose to the user.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The se7751 was still doing the PCI fixups in its own board directory,
so we move it over to arch/sh/drivers/pci/ with the rest of the board
fixups. It has bitrotted significantly over the years, so will still
likely need a bit of work to bring back up to date.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This introduces a saner pcibios_align_resource() that can be used
regardless of whether pci-auto or pci-new are being used, and
consolidates it in pci-lib.c.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 68b42d1b54 ("sh: sh7785lcr: Map
whole PCI address space.") changed around the semantics of how various
chip-selects are made accessible to PCI. Now that there is a single
large mapping covering from CS0-CS6, there is no longer any need to
do multi-window mapping. Subsequently, all of the differing
implementations can be consolidated in to pci-sh7780.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes the code to use __is_pci_memory() instead of
is_pci_memaddr(). __is_pci_memory() loops through all the pci
channels on the system to match memory windows.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds an init callback to struct pci_channel and makes sure
it is initialized properly. Code is added to call this init function
from pcibios_init(). Return values are adjusted and a warning is is
printed if init fails.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the V4L bits have finally settled..
This patch adds support for a secondary ov772x camera on ap325rxa.
This is supported in addition to the regular soc_camera_platform camera.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All soc-camera camera and host drivers must specify supported data signal
polarity, after all drivers are fixed, we'll add a suitable test to
soc_camera_bus_param_compatible().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Waiting for a free bus now accepts the timeout value in jiffies and does
proper checking using time_before.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Polaris is an SMSC reference platform with a SH7709S CPU and LAN9118
ethernet controller. This patch adds support for it.
Updated following feedback from Nobuhiro Iwamatsu.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rework the hd64461 demuxer code to fix the HD64461 level-triggered
interrupts handling, using handle_level_irq() as needed.
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
IRQ for sh_eth of sh7763rdp became multi handling.
Therefore, the IRQ number of sh_eth is changed, too.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the ESPT-Giga (Ethernet Serial Parallel
Translator) SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve the ap325 board code to allow the lcd panel
and backlight to be powered off.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve the sh7785lcr power off implementation to
never return. It takes some time before the board
is actually powered off, just hang after asking
the harware to power down.
This removes the serial port garbage printout.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a new defconfig for SH7785LCR in 32-bit mode, and update the power
off code to avoid 29-bit assumptions.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If CONFIG_PM is set, let Migo-R LEDs show sleep states.
D11 will show STATUS0 and D12 PDSTATUS.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Other compilation errors were revised by commit of
"sh: ap325rxa: Revert ov772x support"
(08c2f5b4d7) but other compilation
errors are given.
We revert this commit and need to add new header(media/soc_camera.h).
This change revises new compilation error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786-based Urquell board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register saving code in
the following ways:
- break out prepare_stack_save_dsp() from handle_exception()
- break out save_regs() from handle_exception()
- the register saving order is unchanged
- align new functions to fit in cache lines
- separate exception code from interrupt code
- keep main code flow in a single cache line per exception vector
- use bsr/rts for regular functions (save pr first)
- keep data in one shared cache line (exception_data)
- document the functions
- tie in the hp6xx code
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This change depends on some v4l changes that have been pushed back to
2.6.30, so drop this and fall back on the old soc_camera code until then.
Reported-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Acked-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch add ov772x camera settings to ap325,
Old camera is still supported. And it will be 2nd camera
if you select ov772x and soc_camera_platform in same time.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix up the build for mach-highlander and mach-rsk. These operated on the
assumption that GENERIC_GPIO support with an optional GPIOLIB was
possible. This used to be true, but has not been the case since commit-id
d56cc8bc661ac1ceded8d45ba2d53bb134fee17d ("sh: use gpiolib"), where the
GENERIC_GPIO implementation was rewritten to use GPIOLIB directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the SuperH gpio code to make use of gpiolib. The
gpiolib callbacks get() and set() are lockless, but we use our own
spinlock for the other operations to make sure hardware register
bitfield accesses stay atomic.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds CN9 MMC support for MigoR using the mmc_spi
driver on top of the bitbanging spi_gpio driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds CN3 MMC support for ap325rxa using the mmc_spi
driver on top of the bitbanging spi_gpio driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since commit ba84be2338
("remove linux/hardirq.h from asm-generic/local.h"), the asm/irq.h
definitions that mach-x3proto/setup.c depends on are no longer available,
causing the build to die. So, include linux/irq.h explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Migo-R can use ov772x camera driver in Linux 2.6.29.
Therefore, soc_camera_platform setting is no longer needed.
This patch removes it.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable LCDC deferred io on Migo-R using 1s delay.
As with other deferred io frame buffers user space code should
use fsync() on the frame buffer device to trigger an update.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add LCDC interrupt resources for AP325 and Migo-R. The LCDC driver does
not require interrupts at this point, but changes such as one-shot SYS
mode using deferred io, and wait-for-vblank will both need this.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the rest of the boards that were using cf-enabler "generically"
have switched to setting up their mappings on their own, only the mach-se
boards were left using it. All of the cf-enabler using mach-se boards
use a special initialization of the MRSHPC windows rather than going
through the special PTE as other SH-4 platforms do. This consolidates
the MRSHPC setup logic, hooks it up on the boards that care, and gets rid
of any and all remaining references to cf-enabler.
This has been long overdue, as cf-enabler has been the bane of
arch/sh/kernel for the last 7 years. Good riddance.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This also fixes up a long-standing bug for this platform where the PIO
base was set to a register offset, rather than the actual PIO offset
itself.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This gets rid of the cf enabler use on mach-sh03 and switches to use
pata_platform with the proper address directly. cf_enabler is
subsequently disabled for mach-sh03.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I've been unable to even compile-test this change because I don't have
an sh5 toolchain. All uses of hw_interrupt_type for SuperH boards have
now been converted to use irq_chip.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Switch the dreamcast IRQ code over to the irq_chip way of doing things,
so that we can set GENERIC_HARDIRQS_NO__DO_IRQ for all SuperH boards.
Also, whilst I'm here change some things to make checkpatch.pl happy:
- Indent with tabs, not with spaces
- Include <linux/io.h>, not <asm/io.h>
- Fix the multi-line comment style
- Fix some typos in the comments
Tested-by: Adrian McMenamin <adrian@newgolddream.dyndns.info>
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This kills off the special Migo-R machvec, as nothing is using it. By
default this will switch to using the generic machvec, which provides the
same functionality. This saves us a bit of space in the machvec section.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
RSK+ platforms have quite a few characteristics in common, so roll them
together in to a shiny new RSK mach-type.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the not-so-generic pm code from arch/sh/kernel/pm.c to the
platform directory together with the rest of the hp6xx pm code.
This is done to let non-hp6xx platforms enable CONFIG_PM.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove out-of-date se7343 ioport code including some old support
for unknown-ne2000-pcmcia-card, cf-over-pcmcia and a mysterical
smc91x that once must have been on a special daughterboard.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add isp1161 platform data to get usb host working on se7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
