Intel8x0-modem driver
With some intel based ac97 modems codec access semaphore is not cleared
after 0x54 AC97 register (GPIO_STATUS) reads. This may causes problems
with newly applied modem mixer (Off-hook switch) and in other cases.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
- Added CM9780 patch
- Fix the SPDIF support on CM9761/CM9780
- Allow the generic enum callback to pass any number (not power of 2)
as the value mask
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB generic driver
This patch adds quirks to support 24-bit PCM I/O in the 'Advanced
Driver' mode of the BOSS GS-10.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
ALSA sequencer
The last change to reduce stack usage did not adjust the parameter to
SNDRV_SEQ_IOCTL_CREATE_PORT which resulted in passing the address of
the pointer instead of the structure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
EMU10K1/EMU10K2 driver
This add identification of Audigy 1 model SB0090 and fixes
problems with ac97 codec (mic not working).
Signed-off-by: Peter Zubaj <pzad@pobox.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB generic driver
This patch reintroduces the check for endpoint numbers that are
specified explicitly in the quirk structure.
This check was accidentally dropped in the last rewrite of
snd_usbmidi_detect_endpoints().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
EMU10K1/EMU10K2 driver
Use expliciitly the old default id strings for backward compatibility.
This will make 'alsactl restore' working again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
This patch converts the emu10k1 driver to use the card capabilities
structure for some more things.
Not extensively tested but seems to work.
Signed-off-by: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
Fixed the detection of bit resolution of ac97 mixer controls.
This will fix the problem with TI ac97 codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
One can select which capture source, but one cannot yet set volumes.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
HDA Codec driver
The patch_cm9880.c can't play side/C/B channels from front panel jacks.
I fixed it by adding select pin.
Signed-off-by: ChenLi Tien <cltien@cmedia.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA generic driver
During debugging for cm9880 multi-channel playback, I added the * after
the currently selected widget, mixer widget doesn't need this but other
3 widget types need it.
Signed-off-by: ChenLi Tien <cltien@cmedia.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA<-OSS emulation
The Coverity checker found this obviously dead code.
I'm not sure which of the if (plugin == NULL) is correct - this patch
removes the one that couldn't be true.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The g5 support code broke some earlier models unfortunately as those bail
out early from the detect function, before the point where I added the code
to locate the PCI device for use with DMA allocations.
This patch fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds dummy gameport_register_port, gameport_unregister_port
and gameport_set_phys functions to gameport.h for the case when a driver
can't use gameport.
This fixes the compilation of some OSS drivers with GAMEPORT=n without
the need to #if inside every single driver.
This patch also removes the non-working and now obsolete SOUND_GAMEPORT.
This patch is also an alternative solution for ALSA drivers with similar
problems (but #if's inside the drivers might have the advantage of
saving some more bytes of gameport is not available).
The only user-visible change is that for GAMEPORT=m the affected OSS
drivers are now allowed to be built statically (but they won't have
gameport support).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Trying software suspend on my workstation makes it crash on resume. The
problem is that via82xx marks the chip_init function as _devinit, but calls
it on resume as well.
Cc: <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch works around the misdetection of the CXT48 codec as a
modem by the OSS ac97 driver.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a typo in the Intel AC'97 audio driver intel8x0.c for
Intel ESB2.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Cc: <tiwai@suse.de>
Cc: <perex@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As Al Viro noticed, my previous fix missed one instance of "device" in
the driver local debug code. Harmless unless you tweak the #define's in
there but still work fixing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My newer iMac mini driver doesn't build with verbose debug enabled.
This fixes it, and removes an erroneous error printk (since it's normal
on some machine to not find some gpios on the "first try").
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes an array overflow found by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the Intel ESB2 HD Audio DID to the hda_intel.c audio driver.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ben's patch that shutdowns master switch and restores it after resume
("pmac: Improve sleep code of tumbler driver") isn't enough here on an
iBook (snapper chip).
The master switch is correctly saved and restored, but somehow
tumbler_put_master_volume() gets called just after
tumbler_set_master_volume() and sets mix->master_vol[*] to 0. So, on
resuming, the master switch is reenabled, but the volume is set to 0.
Here's a patch that also saves and restores master_vol.
Signed-off-by: Colin Leroy <colin@colino.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch applies on top of my previous g5 related sound patches and adds
support for the Mac Mini to the PowerMac Alsa driver.
However, I haven't found any kind of HW support for volume control on this
machine. If it exist, it's well hidden. That means that you probably want
to make sure you use software with the ability to do soft volume control,
or use Alsa 0.9 pre-release with the softvol plugin.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a couple more issues with the management of the GPIOs
dealing with headphone and line out mute on the G5. It should fix the
remaining problems of people not getting any sound out of the headphone
jack.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This beast is pmac-only; moreover, it won't build on other
subarchitectures.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dumb typo - __get_free_page() takes gfp mask (in this case -
GFP_KERNEL), not the page size...
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Compiling SOUND_AD1889 with PCI=n results in the following compile
error:
sound/built-in.o(.text+0x24f0c): In function `ad1889_remove':
: undefined reference to `pci_release_region'
This patch adds the missing dependency on PCI.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
opl3sa2: Fix "irq"-parameter name typo for parameter description.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes u32 vs. pm_message_t confusion in remaining places. Fortunately
there's few of them.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I thought I'm done with fixing u32 vs. pm_message_t ... unfortunately that
turned out not to be the case as Russel King pointed out. This fixes last few
bits in alsa.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Intel ESB2 DID's to the intel8x0.c file for AC'97 audio
support.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch hacks the current PowerMac Alsa driver to add some basic support
of analog sound output to some desktop G5s. It has severe limitations
though:
- Only 44100Khz 16 bits
- Only work on G5 models using a TAS3004 analog code, that is early
single CPU desktops and all dual CPU desktops at this date, but none
of the more recent ones like iMac G5.
- It does analog only, no digital/SPDIF support at all, no native
AC3 support
Better support would require a complete rewrite of the driver (which I am
working on, but don't hold your breath), to properly support the diversity
of apple sound HW setup, including dual codecs, several i2s busses, all the
new codecs used in the new machines, proper clock switching with digital,
etc etc etc...
This patch applies on top of the other PowerMac sound patches I posted in
the past couple of days (new powerbook support and sleep fixes).
Note: This is a FAQ entry for PowerMac sound support with TI codecs: They
have a feature called "DRC" which is automatically enabled for the internal
speaker (at least when auto mute control is enabled) which will cause your
sound to fade out to nothing after half a second of playback if you don't
set a proper "DRC Range" in the mixer. So if you have a problem like that,
check alsamixer and raise your DRC Range to something reasonable.
Note2: This patch will also add auto-mute of the speaker when line-out jack
is used on some earlier desktop G4s (and on the G5) in addition to the
headphone jack. If that behaviour isn't what you want, just disable
auto-muting and use the manual mute controls in alsamixer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch improves the behaviour of the "tumbler/snapper" driver used on
newer PowerMacs during sleep. It properly set the HW mutes to shut down
amplifiers and does an analog shutdown of the codec. That might improve
power consumption during sleep on a number of machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch hacks the current Alsa snd-powermac driver to add support for
recent machine models with the tas3004 chip, that is basically new laptop
models. The Mac Mini is _NOT_ yet supported by this patch (soon soon ...).
The G5s (iMac or Desktop) will need the rewritten sound driver on which
I'm working on (I _might_ get a hack for analog only on some G5s on the
current driver, but no promise).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
