The PowerPC legacy iSeries platform is being removed, so this code is no
longer needed.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a udbg and an hvc console backend for supporting a console
using the OPAL console interfaces.
On OPAL v1 we have hvc0 mapped to whatever console the system was
configured for (network or hvsi serial port) via the service
processor.
On OPAL v2 we have hvcN mapped to the Nth console provided by OPAL
which generally corresponds to:
hvc0 : network console (raw protocol)
hvc1 : serial port S1 (hvsi)
hvc2 : serial port S2 (hvsi)
Note: At this point, early debug console only works with OPAL v1
and shouldn't be enabled in a normal kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On pseries machines, consoles are provided by the hypervisor using
a low level get_chars/put_chars type interface. However, this is
really just a transport to the service processor which implements
them either as "raw" console (networked consoles, HMC, ...) or as
"hvsi" serial ports.
The later is a simple packet protocol on top of the raw character
interface that is supposed to convey additional "serial port" style
semantics. In practice however, all it does is provide a way to
read the CD line and set/clear our DTR line, that's it.
We currently implement the "raw" protocol as an hvc console backend
(/dev/hvcN) and the "hvsi" protocol using a separate tty driver
(/dev/hvsi0).
However this is quite impractical. The arbitrary difference between
the two type of devices has been a major source of user (and distro)
confusion. Additionally, there's an additional mini -hvsi implementation
in the pseries platform code for our low level debug console and early
boot kernel messages, which means code duplication, though that low
level variant is impractical as it's incapable of doing the initial
protocol negociation to establish the link to the FSP.
This essentially replaces the dedicated hvsi driver and the platform
udbg code completely by extending the existing hvc_vio backend used
in "raw" mode so that:
- It now supports HVSI as well
- We add support for hvc backend providing tiocm{get,set}
- It also provides a udbg interface for early debug and boot console
This is overall less code, though this will only be obvious once we
remove the old "hvsi" driver, which is still available for now. When
the old driver is enabled, the new code still kicks in for the low
level udbg console, replacing the old mini implementation in the platform
code, it just doesn't provide the higher level "hvc" interface.
In addition to producing generally simler code, this has several benefits
over our current situation:
- The user/distro only has to deal with /dev/hvcN for the hypervisor
console, avoiding all sort of confusion that has plagued us in the past
- The tty, kernel and low level debug console all use the same code
base which supports the full protocol establishment process, thus the
console is now available much earlier than it used to be with the
old HVSI driver. The kernel console works much earlier and udbg is
available much earlier too. Hackers can enable a hard coded very-early
debug console as well that works with HVSI (previously that was only
supported for the "raw" mode).
I've tried to keep the same semantics as hvsi relative to how I react
to things like CD changes, with some subtle differences though:
- I clear DTR on close if HUPCL is set
- Current hvsi triggers a hangup if it detects a up->down transition
on CD (you can still open a console with CD down). My new implementation
triggers a hangup if the link to the FSP is severed, and severs it upon
detecting a up->down transition on CD.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This converts the existing bfin_jtag_comm TTY driver to the HVC layer so
that the common HVC code can worry about all of the TTY/polling crap and
leave the Blackfin code to worry about the Blackfin bits.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 728674a7e4 moved virtio_console.c
to drivers/tty/hvc/ under the perception of this being an hvc driver.
It was such once, but these days it has generic communication
capabilities as well, so move it to drivers/char/.
In the future, the hvc part from this file can be split off and moved
under drivers/tty/hvc/.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As requested by Arnd Bergmann, the hvc drivers are now
moved to the drivers/tty/hvc/ directory. The virtio_console.c driver
was also moved, as it required the hvc_console.h file to be able to be
built, and it really is a hvc driver.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
