First, don't look at the interrupt status in the poll loop
to decide what to poll. It's wrong. If we have run out of
budget, we may still have RX packets to unqueue but no more
RX interrupt pending.
So instead move the code looking at the interrupt status
into the interrupt handler where it belongs. That avoids a slow
MMIO read in the NAPI fast path. We keep the abnormal interrupts
enabled while NAPI is scheduled.
While at it, actually do something useful in the "error" cases:
On AHB bus error, trigger the new reset task, that's about all
we can do. On RX packet fifo or descriptor overflows, we need
to restart the MAC after having freed things up. So set a flag
that NAPI will see and use to perform that restart after
harvesting the RX ring.
Finally, we shouldn't complete NAPI if there are still outgoing
packets that will need harvesting. Waiting for more interrupts
is less efficient than letting NAPI run a while longer while
the queue drains.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt is neither enabled nor registered when the interface
isn't running (regardless of whether we use nc-si or not) so the
test isn't useful.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW requires a full MAC reset when changing the speed.
Additionally the Aspeed documentation spells out that the
MAC needs to be reset twice with a 10us interval.
We thus move the speed setting and top level reset code
into a new ftgmac100_reset_and_config_mac() function which
handles both. Move the ring pointers initialization there
too in order to reflect the HW change.
Also reduce the timeout for the MAC reset as it shouldn't
take more than 300 clock cycles according to the doc.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link speed changes require a full HW reset. This isn't done
properly at the moment. It will involve delays and thus isn't
suitable to do from the link poll callback.
So let's create a reset_task that we can queue up when the
link changes. It will be useful for various cases of error
handling as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link monitoring and error handling code will have to
redo the ring inits and HW setup so move the code out of
ftgmac100_open() into a dedicated function.
This forces a bit of re-ordering of ftgmac100_open() but
nothing dramatic.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt isn't shared, so this will keep it masked
until we have the HW in a known sane state.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a single function is used to allocate the rings
themselves, initialize them, populate the rx ring, and
allocate the rx buffers. The same happens on free.
This splits them into separate functions. This will be
useful when properly implementing re-initialization on
link changes and error handling when the rings will be
repopulated but not freed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep track of both the current speed and duplex settings
instead of only speed and properly apply the duplex setting
to the HW.
This reworks the adjust_link() function to also avoid trying
to reconfigure the HW when there is no link and to display
the link state to the user.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not used in any meaningful way
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder the fields in struct ftgmac in slightly more logical
groups. Will make more sense as I add/remove some.
No code change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The divisions they represent are not particularily meaningful
and things are going to be moving around with upcoming changes
making these comments more a burden than anything else.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a placeholder already for the irq, use it
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of watchdog timeout of Octeon cores is flawed and susceptible to
false alarms. Refactor by removing the detection code, and in its place,
leverage existing code that monitors for an indication from the NIC
firmware that an Octeon core crashed; expand the meaning of the indication
to "an Octeon core crashed or its watchdog timer expired". Detection of
watchdog timeout is now delegated to an exception handler in the NIC
firmware; this is free of false alarms.
Also if there's an Octeon core crash or watchdog timeout:
(1) Disable VF Ethernet links.
(2) Decrement the module refcount by an amount equal to the number of
active VFs of the NIC whose Octeon core crashed or had a watchdog
timeout. The refcount will continue to reflect the active VFs of
other liquidio NIC(s) (if present) whose Octeon cores are faultless.
Item (2) is needed to avoid the case of not being able to unload the driver
because the module refcount is stuck at some non-zero number. There is
code that, in normal cases, decrements the refcount upon receiving a
message from the firmware that a VF driver was unloaded. But in
exceptional cases like an Octeon core crash or watchdog timeout, arrival of
that particular message from the firmware might be unreliable. That normal
case code is changed to not touch the refcount in the exceptional case to
avoid contention (over the refcount) with the liquidio_watchdog kernel
thread who will carry out item (2).
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With GCC 6.3, we can get the following warning:
drivers/net/usb/usbnet.c:85:19: warning: 'driver_name' defined but not
used [-Wunused-const-variable=]
static const char driver_name [] = "usbnet";
^~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix artifact of merge resolution
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a tracepoint (rxrpc_connect_call) to log the combination of rxrpc_call
pointer, afs_call pointer/user data and wire call parameters to make it
easier to match the tracebuffer contents to captured network packets.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a tracepoint (rxrpc_rx_rwind_change) to log changes in a call's receive
window size as imposed by the peer through an ACK packet.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a tracepoint (rxrpc_rx_proto) to record protocol errors in received
packets. The following changes are made:
(1) Add a function, __rxrpc_abort_eproto(), to note a protocol error on a
call and mark the call aborted. This is wrapped by
rxrpc_abort_eproto() that makes the why string usable in trace.
(2) Add trace_rxrpc_rx_proto() or rxrpc_abort_eproto() to protocol error
generation points, replacing rxrpc_abort_call() with the latter.
(3) Only send an abort packet in rxkad_verify_packet*() if we actually
managed to abort the call.
Note that a trace event is also emitted if a kernel user (e.g. afs) tries
to send data through a call when it's not in the transmission phase, though
it's not technically a receive event.
Signed-off-by: David Howells <dhowells@redhat.com>
In the rxkad security module, when we encounter a temporary error (such as
ENOMEM) from which we could conceivably recover, don't abort the
connection, but rather permit retransmission of the relevant packets to
induce a retry.
Note that I'm leaving some places that could be merged together to insert
tracing in the next patch.
Signed-off-by; David Howells <dhowells@redhat.com>
Make rxrpc_kernel_abort_call() return an indication as to whether it
actually aborted the operation or not so that kafs can trace the failure of
the operation. Note that 'success' in this context means changing the
state of the call, not necessarily successfully transmitting an ABORT
packet.
Signed-off-by: David Howells <dhowells@redhat.com>
Use negative error codes in struct rxrpc_call::error because that's what
the kernel normally deals with and to make the code consistent. We only
turn them positive when transcribing into a cmsg for userspace recvmsg.
Signed-off-by: David Howells <dhowells@redhat.com>
Interfaces will reset whenever the TX mailbox FIFO has become full. This
occurs more frequently whenever the IES API application is not running
to process and clear the messages in the FIFO. Thus, this could lead to
situations where the interface would enter an infinite reset loop. That
is: if the interface is trying to synchronize a huge number of unicast
and multicast entries with the IES API application, the TX mailbox FIFO
will become full and the interface resets. Once the interface exits
reset, it'll try to synchronize the unicast and multicast entries again.
Ergo, this creates an infinite loop. Other actions such as multiple
mulitcast mode or up/down transitions will fill the TX mailbox FIFO and
induce the interface to reset. To correct these situations, check if the
interface's "host_ready" flag is enabled before enqueuing any messages
to the TX mailbox FIFO. This check will be conducted by a function call.
Lastly, this issue mainly affects the PF and, thus, the VF is exempt.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Write to RXQCTL register to disable the receive queue when configuring
the RX ring.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Re-word the comment to avoid stating that we return a value for this
void function. Additionally, there is no need to mention older kernels,
since this is the upstream kernel.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If some code path executes fm10k_service_event_schedule(), it is
guaranteed that we only queue the service task once, since we use
__FM10K_SERVICE_SCHED flag. Unfortunately this has a side effect that if
a service request occurs while we are currently running the watchdog, it
is possible that we will fail to notice the request and ignore it until
the next time the request occurs.
This can cause problems with pf/vf mailbox communication and other
service event tasks. To avoid this, introduce a FM10K_SERVICE_REQUEST
bit. When we successfully schedule (and set the _SCHED bit) the service
task, we will clear this bit. However, if we are unable to currently
schedule the service event, we just set the new SERVICE_REQUEST bit.
Finally, after the service event completes, we will re-schedule if the
request bit has been set.
This should ensure that we do not miss any service event schedules,
since we will re-schedule it once the currently running task finishes.
This means that for each request, we will always schedule the service
task to run at least once in full after the request came in.
This will avoid timing issues that can occur with the service event
scheduling. We do pay a cost in re-running many tasks, but all the
service event tasks use either flags to avoid duplicate work, or are
tolerant of being run multiple times.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This ensures that future programmers do not have to remember to re-size
the bitmaps due to adding new values. Although this is unlikely for this
driver, it may happen and it's best to prevent it from ever being an
issue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace bitwise operators and #defines with a BITMAP and enumeration
values. This is similar to how we handle the "state" values as well.
This has two distinct advantages over the old method. First, we ensure
correctness of operations which are currently problematic due to race
conditions. Suppose that two kernel threads are running, such as the
watchdog and an ethtool ioctl, and both modify flags. We'll say that the
watchdog is CPU A, and the ethtool ioctl is CPU B.
CPU A sets FLAG_1, which can be seen as
CPU A read FLAGS
CPU A write FLAGS | FLAG_1
CPU B sets FLAG_2, which can be seen as
CPU B read FLAGS
CPU A write FLAGS | FLAG_2
However, "|=" and "&=" operators are not actually atomic. So this could
be ordered like the following:
CPU A read FLAGS -> variable
CPU B read FLAGS -> variable
CPU A write FLAGS (variable | FLAG_1)
CPU B write FLAGS (variable | FLAG_2)
Notice how the 2nd write from CPU B could actually undo the write from
CPU A because it isn't guaranteed that the |= operation is atomic.
In practice the race windows for most flag writes is incredibly narrow
so it is not easy to isolate issues. However, the more flags we have,
the more likely they will cause problems. Additionally, if such
a problem were to arise, it would be incredibly difficult to track down.
Second, there is an additional advantage beyond code correctness. We can
now automatically size the BITMAP if more flags were added, so that we
do not need to remember that flags is u32 and thus if we added too many
flags we would over-run the variable. This is not a likely occurrence
for fm10k driver, but this patch can serve as an example for other
drivers which have many more flags.
This particular change does have a bit of trouble converting some of the
idioms previously used with the #defines for flags. Specifically, when
converting FM10K_FLAG_RSS_FIELD_IPV[46]_UDP flags. This whole operation
was actually quite problematic, because we actually stored flags
separately. This could more easily show the problem of the above
re-ordering issue.
This is really difficult to test whether atomics make a difference in
practical scenarios, but you can ensure that basic functionality remains
the same. This patch has a lot of code coverage, but most of it is
relatively simple.
While we are modifying these files, update their copyright year.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FM10K_REMOVED expects a hardware address, not a 'struct fm10k_hw'.
Fixes: 5cb8db4a4c ("fm10k: Add support for VF")
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
1) Reject invalid updates to netfilter expectation policies, from Pablo
Neira Ayuso.
2) Fix memory leak in nfnl_cthelper, from Jeffy Chen.
3) Don't do stupid things if we get a neigh_probe() on a neigh entry
whose ops lack a solicit method. From Eric Dumazet.
4) Don't transmit packets in r8152 driver when the carrier is off, from
Hayes Wang.
5) Fix ipv6 packet type detection in aquantia driver, from Pavel
Belous.
6) Don't write uninitialized data into hw registers in bna driver, from
Arnd Bergmann.
7) Fix locking in ping_unhash(), from Eric Dumazet.
8) Make BPF verifier range checks able to understand certain sequences
emitted by LLVM, from Alexei Starovoitov.
9) Fix use after free in ipconfig, from Mark Rutland.
10) Fix refcount leak on force commit in openvswitch, from Jarno
Rajahalme.
11) Fix various overflow checks in AF_PACKET, from Andrey Konovalov.
12) Fix endianness bug in be2net driver, from Suresh Reddy.
13) Don't forget to wake TX queues when processing a timeout, from
Grygorii Strashko.
14) ARP header on-stack storage is wrong in flow dissector, from Simon
Horman.
15) Lost retransmit and reordering SNMP stats in TCP can be
underreported. From Yuchung Cheng.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (82 commits)
nfp: fix potential use after free on xdp prog
tcp: fix reordering SNMP under-counting
tcp: fix lost retransmit SNMP under-counting
sctp: get sock from transport in sctp_transport_update_pmtu
net: ethernet: ti: cpsw: fix race condition during open()
l2tp: fix PPP pseudo-wire auto-loading
bnx2x: fix spelling mistake in macros HW_INTERRUT_ASSERT_SET_*
l2tp: take reference on sessions being dumped
tcp: minimize false-positives on TCP/GRO check
sctp: check for dst and pathmtu update in sctp_packet_config
flow dissector: correct size of storage for ARP
net: ethernet: ti: cpsw: wake tx queues on ndo_tx_timeout
l2tp: take a reference on sessions used in genetlink handlers
l2tp: hold session while sending creation notifications
l2tp: fix duplicate session creation
l2tp: ensure session can't get removed during pppol2tp_session_ioctl()
l2tp: fix race in l2tp_recv_common()
sctp: use right in and out stream cnt
bpf: add various verifier test cases for self-tests
bpf, verifier: fix rejection of unaligned access checks for map_value_adj
...
We should unregister the net_device first, before we give back
our reference on xdp_prog. Otherwise xdp_prog may be freed
before .ndo_stop() disabled the datapath. Found by code inspection.
Fixes: ecd63a0217 ("nfp: add XDP support in the driver")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
People are using bonding over Infiniband IPoIB connections, and who knows
what else. Infiniband has a hardware address length of 20 octets
(INFINIBAND_ALEN), and the network core defines a MAX_ADDR_LEN of 32.
Various places in the bonding code are currently hard-wired to 6 octets
(ETH_ALEN), such as the 3ad code, which I've left untouched here. Besides,
only alb is currently possible on Infiniband links right now anyway, due
to commit 1533e77315, so the alb code is where most of the changes are.
One major component of this change is the addition of a bond_hw_addr_copy
function that takes a length argument, instead of using ether_addr_copy
everywhere that hardware addresses need to be copied about. The other
major component of this change is converting the bonding code from using
struct sockaddr for address storage to struct sockaddr_storage, as the
former has an address storage space of only 14, while the latter is 128
minus a few, which is necessary to support bonding over device with up to
MAX_ADDR_LEN octet hardware addresses. Additionally, this probably fixes
up some memory corruption issues with the current code, where it's
possible to write an infiniband hardware address into a sockaddr declared
on the stack.
Lightly tested on a dual mlx4 IPoIB setup, which properly shows a 20-octet
hardware address now:
$ cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: fault-tolerance (active-backup) (fail_over_mac active)
Primary Slave: mlx4_ib0 (primary_reselect always)
Currently Active Slave: mlx4_ib0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 100
Down Delay (ms): 100
Slave Interface: mlx4_ib0
MII Status: up
Speed: Unknown
Duplex: Unknown
Link Failure Count: 0
Permanent HW addr:
80:00:02:08:fe:80:00:00:00:00:00:00:e4:1d:2d:03:00:1d:67:01
Slave queue ID: 0
Slave Interface: mlx4_ib1
MII Status: up
Speed: Unknown
Duplex: Unknown
Link Failure Count: 0
Permanent HW addr:
80:00:02:09:fe:80:00:00:00:00:00:01:e4:1d:2d:03:00:1d:67:02
Slave queue ID: 0
Also tested with a standard 1Gbps NIC bonding setup (with a mix of
e1000 and e1000e cards), running LNST's bonding tests.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the reordering SNMP counters only increase if a connection
sees a higher degree then it has previously seen. It ignores if the
reordering degree is not greater than the default system threshold.
This significantly under-counts the number of reordering events
and falsely convey that reordering is rare on the network.
This patch properly and faithfully records the number of reordering
events detected by the TCP stack, just like the comment says "this
exciting event is worth to be remembered". Note that even so TCP
still under-estimate the actual reordering events because TCP
requires TS options or certain packet sequences to detect reordering
(i.e. ACKing never-retransmitted sequence in recovery or disordered
state).
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lost retransmit SNMP stat is under-counting retransmission
that uses segment offloading. This patch fixes that so all
retransmission related SNMP counters are consistent.
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mc_list is longer than 256 addresses, we enter mc_promisc mode.
If we're in mc_promisc mode and the firmware doesn't support cascaded
multicast, normally we also insert our mc_list, to prevent stealing by
another VI. However, if the mc_list was too long, this isn't really
helpful - the MC groups that didn't fit in the list can still get
stolen, and having only some of them stealable will probably cause
more confusing behaviour than having them all stealable. Since
inserting 256 multicast filters takes a long time and can lead to MCDI
state machine timeouts, just skip the mc_list insert in this overflow
condition.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: ethtool link settings
This series adds support for getting and setting link settings
via the (moderately) new ethtool ksettings ops.
First patch introduces minimal speed and duplex reporting using
the information directly provided in PCI BAR0 memory.
Next few changes deal with the need to refresh port state read
from the service process and patch 6 finally uses that information
to provide link speed and duplex. Patches 7 and 8 add auto
negotiation and port type reporting.
Remaining changes provide the set support for speed and auto
negotiation. An upcoming series will also add port splitting
support via devlink.
Quite a bit of churn in this series is caused by the fact that
currently port speed and split changes will usually require a
reboot to take effect. Current service process code is not capable
of performing MAC reinitialization after chip has been passing
traffic. To make sure user is aware of this limitation we refuse
the configuration unless netdev is down, print warning to the logs
and if configuration was performed but did take effect we unregister
the netdev. Service process has a "reboot needed" sticky bit, so
reloading the driver will not bring the netdev back.
Note that there is a helper in patch 13 which is marked as
__always_inline, because the FIELD_* macros require the parameters
to be known at compilation time. I hope that is OK.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support setting link speed and autonegotiation through
set_link_ksettings() ethtool op. If the port is reconfigured
in incompatible way and reboot is required the netdev will get
unregistered and not come back until user reboots the system.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NSP backend for upcoming link configuration operations.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow NSP to set option code even when error is reported. This provides
a way for NSP to give user more precise information about why command
failed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make NSP port structure a union to simplify accessing the fields
from generic macros.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSP commands may be slow to respond, we should try to avoid doing
a command-per-item when user requested to change multiple parameters
for instance with an ethtool .set_settings() command.
Introduce a way of internal NSP code to carry state in NSP structure
and add start/finish calls to perform the initialization and kick off
of the configuration request, with potentially many parameters being
modified in between.
nfp_eth_set_mod_enable() will make use of the new code internally,
other "set" functions to follow.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon add more NSP commands and structure definitions.
Move all high-level NSP header contents to a common nfp_nsp.h file.
Right now it mostly boils down to renaming nfp_nsp_eth.h and
moving some functions from nfp.h there.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Service process firmware provides us with information about media
and interface (SFP module) plugged in, translate that to Linux's
PORT_* defines and report via ethtool.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSP ABI version 0.17 is exposing the autonegotiation settings.
Report whether autoneg is on via ethtool.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the PF prefer the link speed value provided by the NSP.
Refresh port table if needed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will need a way of refreshing port state for link settings
get/set. For get we need to refresh port speed and type.
When settings are changed the reconfiguration may require
reboot before it's effective. Unregister netdevs affected
by reconfiguration from a workqueue.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For caching link settings - remember if we have seen link events
since the last time the eth_port information was refreshed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will want to unregister netdevs after their port got reconfigured.
For that we need to make sure manipulations of port list from the
port reconfiguration flow will not race with driver's .remove()
callback.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
