This patch adds {read,write}*_be big endian memory access
routines to the io.h header used on SPARC32 and SPARC64.
Tested on SPARC32 (LEON)
Signed-off-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are in the label cc_dword_align, registers %o0 and %o1 have the same last 2 bits,
but it's not guaranteed one of them is zero. So we can get unaligned memory access
in label ccte. Example of parameters which lead to this:
%o0=0x7ff183e9, %o1=0x8e709e7d, %g1=3
With the parameters I had a memory corruption, when the additional 5 bytes were rewritten.
This patch corrects the error.
One comment to the patch. We don't care about the third bit in %o1, because cc_end_cruft
stores word or less.
Signed-off-by: Tkhai Kirill <tkhai@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sparcstation 5 I have available has no MID property for the CPU.
This resulted in a panic when booting a SMP kernel on this box.
The assigned field in cpu_data is never used, so if we fail
to read the MID property then inform user and continue booting.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all cases there were a struct of_device_id variable defined __initdata.
But it was referenced from struct platform_driver.of_match_table
which is not guaranteed to be used during init only.
So drop the __initdata annotation.
This fixes following warnings:
WARNING: arch/sparc/kernel/built-in.o(.data+0x810): Section mismatch in reference from the variable clock_driver to the variable .init.data:clock_match
The variable clock_driver references
the variable __initdata clock_match
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: arch/sparc/kernel/built-in.o(.data+0xcec): Section mismatch in reference from the variable apc_driver to the variable .init.data:apc_match
The variable apc_driver references
the variable __initdata apc_match
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: arch/sparc/kernel/built-in.o(.data+0xd60): Section mismatch in reference from the variable pmc_driver to the variable .init.data:pmc_match
The variable pmc_driver references
the variable __initdata pmc_match
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, gart: Make sure GART does not map physmem above 1TB
x86, gart: Set DISTLBWALKPRB bit always
x86, gart: Convert spaces to tabs in enable_gart_translation
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Fix AMD family 15h FPU event constraints
perf, x86: Fix pre-defined cache-misses event for AMD family 15h cpus
perf evsel: Fix use of inherit
perf hists browser: Fix seg fault when annotate null symbol
Depending on the unit mask settings some FPU events may be scheduled
only on cpu counter #3. This patch fixes this.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@googlemail.com>
Link: http://lkml.kernel.org/r/1302913676-14352-3-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With AMD cpu family 15h a unit mask was introduced for the Data Cache
Miss event (0x041/L1-dcache-load-misses). We need to enable bit 0
(first data cache miss or streaming store to a 64 B cache line) of
this mask to proper count data cache misses.
Now we set this bit for all families and models. In case a PMU does
not implement a unit mask for event 0x041 the bit is ignored.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1302913676-14352-2-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The GART can only map physical memory below 1TB. Make sure
the gart driver in the kernel does not try to map memory
above 1TB.
Cc: <stable@kernel.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1303134346-5805-5-git-send-email-joerg.roedel@amd.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The DISTLBWALKPRB bit must be set for the GART because the
gatt table is mapped UC. But the current code does not set
the bit at boot when the BIOS setup the aperture correctly.
Fix that by setting this bit when enabling the GART instead
of the other places.
Cc: <stable@kernel.org>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1303134346-5805-4-git-send-email-joerg.roedel@amd.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Because of speculative event roll back, it is possible for some event coutners
to decrease between reads on POWER7. This causes a problem with the way that
counters are updated. Delta calues are calculated in a 64 bit value and the
top 32 bits are masked. If the register value has decreased, this leaves us
with a very large positive value added to the kernel counters. This patch
protects against this by skipping the update if the delta would be negative.
This can lead to a lack of precision in the coutner values, but from my testing
the value is typcially fewer than 10 samples at a time.
Signed-off-by: Eric B Munson <emunson@mgebm.net>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This problem was noticed on an MPC855T platform. Ftrace did oops
when trying to write to the kernel text segment.
Many thanks to Joakim for finding the root cause of this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We currently enable interrupts before the dispatch log for the boot
cpu is setup. If a timer interrupt comes in early enough we oops in
scan_dispatch_log:
Unable to handle kernel paging request for data at address 0x00000010
...
.scan_dispatch_log+0xb0/0x170
.account_system_vtime+0xa0/0x220
.irq_enter+0x88/0xc0
.do_IRQ+0x48/0x230
The patch below adds a check to scan_dispatch_log to ensure the
dispatch log has been allocated.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PAPR specifies that DTL buffers can not cross AMS environments (aka CMO
in the PAPR) and can not cross a memory entitlement granule boundary
(4k). This is found in section 14.11.3.2 H_REGISTER_VPA of the PAPR.
kmalloc does not guarantee an alignment of the allocation, though,
beyond 8 bytes (at least in my understanding). Create a special kmem
cache for DTL buffers with the alignment requirement.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent commit b987812b3f caused
a compile failure on UP because a considerably large block
of the file was included within CONFIG_SMP, hence making a stub
function not exposed on UP builds when it needed to be.
Relocate the stub to the #else /* ! CONFIG_SMP */ section
and also annotate the relevant else/endif so that nobody
else falls into the same trap I did.
Reported-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Fix warning 's3c_pm_show_resume_irqs' defined but not used
ARM: SAMSUNG: Fix build failure in PM CRC check code
ARM: S5P: Remove unused s3c_pm_check_resume_pin
Following commit 091738a266 ("genirq: Remove real old transition
functions") we removed an automatic conversion of no_irq_chip to
dummy_irq_chip. This change needs to be propagated back into the alpha
backend.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new warning in gcc 4.6. Several of these variables are
used within #if 0 code, which probably ought to be removed. Most
of the changes are legitimate cleanups.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are outstanding gcc 4.6 warnings that need to be cleaned up
in the subdirectory. No sense forcing the issue immediately.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (43 commits)
Revert "USB: isp1760-hcd: move imask clear after pending work is done"
xHCI: Implement AMD PLL quirk
xhci: Tell USB core both roothubs lost power.
usbcore: Bug fix: system can't suspend with USB3.0 device connected to USB3.0 hub
USB: Fix unplug of device with active streams
USB: xhci - also free streams when resetting devices
xhci: Fix NULL pointer deref in handle_port_status()
USB: xhci - fix math in xhci_get_endpoint_interval()
USB: xhci: simplify logic of skipping missed isoc TDs
USB: xhci - remove excessive 'inline' markings
USB: xhci: unsigned char never equals -1
USB: xhci - fix unsafe macro definitions
USB: fix formatting of SuperSpeed endpoints in /proc/bus/usb/devices
USB: isp1760-hcd: move imask clear after pending work is done
USB: fsl_qe_udc: send ZLP when zero flag and length % maxpacket == 0
usb: qcserial add missing errorpath kfrees
usb: qcserial avoid pointing to freed memory
usb: Fix qcserial memory leak on rmmod
USB: ftdi_sio: add ids for Hameg HO720 and HO730
USB: option: Added support for Samsung GT-B3730/GT-B3710 LTE USB modem.
...
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Set FLAGS_HAS_TIMEOUT during futex_wait restart setup
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_event: Fix cgrp event scheduling bug in perf_enable_on_exec()
perf: Fix a build error with some GCC versions
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix erroneous all_pinned logic
sched: Fix sched-domain avg_load calculation
* 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: rtc-mrst: follow on to the change of rtc_device_register()
RTC: add missing "return 0" in new alarm func for rtc-bfin.c
RTC: Fix s3c compile error due to missing s3c_rtc_setpie
RTC: Fix early irqs caused by calling rtc_set_alarm too early
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd: Disable GartTlbWlkErr when BIOS forgets it
x86, NUMA: Fix fakenuma boot failure
x86/mrst: Fix boot crash caused by incorrect pin to irq mapping
x86/ce4100: Add reg property to bridges
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6879/1: fix personality test wrt usage of domain handlers
ARM: 6878/1: fix personality flag propagation across an exec
ARM: 6877/1: the ADDR_NO_RANDOMIZE personality flag should be honored with mmap()
ARM: 6876/1: Kconfig.debug: Remove unused CONFIG_DEBUG_ERRORS
ARM: pxa: convert incorrect IRQ_TO_IRQ() to irq_to_gpio()
ARM: mmp: align NR_BUILTIN_GPIO with gpio interrupt number
ARM: pxa: align NR_BUILTIN_GPIO with GPIO interrupt number
ARM: pxa: always clear LPM bits for PXA168 MFPR
pcmcia: limit pxa2xx_trizeps4 subdriver to trizeps4 platform
pcmcia: limit pxa2xx_balloon3 subdriver to balloon3 platform
ARM: pxafb: Fix access to nonexistent member of pxafb_info
ARM: 6872/1: arch:common:Makefile Remove unused config in the Makefile.
ARM: 6868/1: Preserve the VFP state during fork
ARM: 6867/1: Introduce THREAD_NOTIFY_COPY for copy_thread() hooks
ARM: 6866/1: Do not restrict HIGHPTE to !OUTER_CACHE
ARM: 6865/1: perf: ensure pass through zero is counted on overflow
ARM: 6864/1: hw_breakpoint: clear DBGVCR out of reset
ARM: Only allow PM_SLEEP with CPUs which support suspend
ARM: Make consolidated PM sleep code depend on PM_SLEEP
This patch disables GartTlbWlk errors on AMD Fam10h CPUs if
the BIOS forgets to do is (or is just too old). Letting
these errors enabled can cause a sync-flood on the CPU
causing a reboot.
The AMD BKDG recommends disabling GART TLB Wlk Error completely.
This patch is the fix for
https://bugzilla.kernel.org/show_bug.cgi?id=33012
on my machine.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/20110415131152.GJ18463@8bytes.org
Tested-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Currently, numa=fake boot parameter is broken. If it's used,
kernel may panic due to devide by zero error depending on CPU
configuration
Call Trace:
[<ffffffff8104ad4c>] find_busiest_group+0x38c/0xd30
[<ffffffff81086aff>] ? local_clock+0x6f/0x80
[<ffffffff81050533>] load_balance+0xa3/0x600
[<ffffffff81050f53>] idle_balance+0xf3/0x180
[<ffffffff81550092>] schedule+0x722/0x7d0
[<ffffffff81550538>] ? wait_for_common+0x128/0x190
[<ffffffff81550a65>] schedule_timeout+0x265/0x320
[<ffffffff81095815>] ? lock_release_holdtime+0x35/0x1a0
[<ffffffff81550538>] ? wait_for_common+0x128/0x190
[<ffffffff8109bb6c>] ? __lock_release+0x9c/0x1d0
[<ffffffff815534e0>] ? _raw_spin_unlock_irq+0x30/0x40
[<ffffffff815534e0>] ? _raw_spin_unlock_irq+0x30/0x40
[<ffffffff81550540>] wait_for_common+0x130/0x190
[<ffffffff81051920>] ? try_to_wake_up+0x510/0x510
[<ffffffff8155067d>] wait_for_completion+0x1d/0x20
[<ffffffff8107f36c>] kthread_create_on_node+0xac/0x150
[<ffffffff81077bb0>] ? process_scheduled_works+0x40/0x40
[<ffffffff8155045f>] ? wait_for_common+0x4f/0x190
[<ffffffff8107a283>] __alloc_workqueue_key+0x1a3/0x590
[<ffffffff81e0cce2>] cpuset_init_smp+0x6b/0x7b
[<ffffffff81df3d07>] kernel_init+0xc3/0x182
[<ffffffff8155d5e4>] kernel_thread_helper+0x4/0x10
[<ffffffff81553cd4>] ? retint_restore_args+0x13/0x13
[<ffffffff81df3c44>] ? start_kernel+0x400/0x400
[<ffffffff8155d5e0>] ? gs_change+0x13/0x13
The divede by zero is caused by the following line,
group->cpu_power==0:
kernel/sched_fair.c::update_sg_lb_stats()
/* Adjust by relative CPU power of the group */
sgs->avg_load = (sgs->group_load * SCHED_LOAD_SCALE) / group->cpu_power;
This regression was caused by commit e23bba6044 ("x86-64, NUMA: Unify
emulated distance mapping") because it changes cpu -> node
mapping in the process of dropping fake_physnodes().
old) all cpus are assinged node 0
now) cpus are assigned round robin
(the logic is implemented by numa_init_array())
Note: The change in behavior only happens if the system doesn't
have neither ACPI SRAT table nor AMD northbridge NUMA
information.
Round robin assignment doesn't work because init_numa_sched_groups_power()
assumes all logical cpus in the same physical cpu share the same node
(then it only accounts for group_first_cpu()), and the simple round robin
breaks the above assumption.
Thus, this patch implements a reassignment of node-ids if buggy firmware
or numa emulation makes wrong cpu node map. Tt enforce all logical cpus
in the same physical cpu share the same node.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/20110415203928.1303.A69D9226@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 8a5ec0ba "Lockless (and preemptless) fastpaths for slub" makes use
of this_cpu_cmpxchg_double() which needs this_cpu_cmpxchg16b_emu() on
x86_64. Implementing cmpxchg16b emulation for UML would introduce too
much complexity. So just disable it.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reported-by: Sergei Trofimovich <slyich@gmail.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 1de1502c ("x86, um: now we can get rid of trivial uml headers")
removed accidentally bug.h which broke UML's call tracer and bug
handler.
Without asm-generic/bug.h UML uses BUG() from arch/x86/ which makes use
of ud2. UML cannot use ud2, it raises SIGILL in user mode. As UML has
a different stack for handling signals the call trace will be cut off.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reported-by: Sergei Trofimovich <slyich@gmail.com>
Tested-by: Sergei Trofimovich <slyich@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a possible problem with mport registration left non-cleared after
fsl_rio_setup() exits on link error. Abort mport initialization if
registration failed.
This patch is applicable to 2.6.39-rc1 only. The problem does not exist
for earlier versions.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are optional bits that may complement a personality ID. It is
therefore wrong to simply test against the absolute current->personality
value to determine the effective personality. The PER_LINUX_32BIT is
itself just PER_LINUX with one of those optional bits set.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Our SET_PERSONALITY() implementation was overwriting all existing
personality flags, including ADDR_NO_RANDOMIZE, making them unavailable
to processes being exec'd after a call to personality() in user space.
This prevents the gdb test suite from running successfully.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This config option isn't actually used anywhere and can be safely
removed. The last user was traps.c before commit 082f47a ([ARM]
always allow dump_stack() to produce a backtrace, 2007-07-05).
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
s3c_pm_show_resume_irqs() is used by some s3c_pm_arch_show_resume_irqs()
implementations, which get included through mach/pm-core.h. Add __maybe_unused
to silence warnings when it isn't used (e.g. on S3C64XX platforms).
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes build error that occurs on enabling the Samsung
specific PM CRC check code. Missed removing this reference of
s3c_sleep_save_phys during move to generic cpu suspend/resume
support.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The s3c_pm_check_resume_pin() is not being used and can be safely
removed to fix the build warning.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The recent commit (10774912647781) wasn't entirely correct. While
it fixed some issues, it introduced others. So pull in the fixes
from the public cache flush functions, and document why we need to
call things directly ourselves.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If the period of a gptimer is fairly low, we might miss an interrupt
by acking it too late (we end up acking the new int as well).
Reported-by: Isabelle Leonardi <i.leonardi@detracom.fr>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We only want to clear the run bit for this one timer, not all status bits.
So don't read the whole reg and then write all the bits back out.
Reported-by: Isabelle Leonardi <i.leonardi@detracom.fr>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When suspending/resuming, the common task freezing code will run in
parallel and freeze processes on each core. This is because the code
uses the non-smp version of memory barriers (as well it should).
The Blackfin smp barrier logic at the moment contains the cache sync
logic, but the non-smp barriers do not. This is incorrect as Rafel
summarized:
> ...
> The existing memory barriers are SMP barriers too, but they are more
> than _just_ SMP barriers. At least that's how it is _supposed_ to be
> (eg. rmb() is supposed to be stronger than smp_rmb()).
> ...
> However, looking at the blackfin's definitions of SMP barriers I see
> that it uses extra stuff that should _also_ be used in the definitions
> of the mandatory barriers.
> ...
URL: http://lkml.org/lkml/2011/4/13/11
LKML-Reference: <BANLkTi=F-C-vwX4PGGfbkdTBw3OWL-twfg@mail.gmail.com>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Disable USB_ARCH_HAS_EHCI in arch Kconfig and enable it in usb Kconfig
Warning log:
warning: (MICROBLAZE) selects USB_ARCH_HAS_EHCI which has unmet
direct dependencies (USB_SUPPORT)
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/avr32-2.6:
avr32: add ATAG_BOARDINFO
don't check platform_get_irq's return value against zero
avr32: init cannot ignore signals sent by force_sig_info()
avr32: fix deadlock when reading clock list in debugfs
avr32: Fix .size directive for cpu_enter_idle
avr32: At32ap: pio fix typo "))" on gpio_irq_unmask prototype
fix the wrong argument of the functions definition
The ATAG_BOARDINFO is intended to hand over the information
bd->bi_board_number from u-boot to the kernel.
This piece of information can be used to implement some kind of board
identification while booting the kernel. Therefore it is placed in .initdata
section and can be accessed via the new symbol board_number only while
initializing the kernel.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
platform_get_irq returns -ENXIO on failure, so !int_irq was probably
always true. Better use (int)int_irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
