Pull input updates from Dmitry Torokhov:
"The first round of updates for the input subsystem.
A few new drivers (power button handler for AXP20x PMIC, tps65218
power button driver, sun4i keys driver, regulator haptic driver, NI
Ettus Research USRP E3x0 button, Alwinner A10/A20 PS/2 controller).
Updates to Synaptics and ALPS touchpad drivers (with more to come
later), brand new Focaltech PS/2 support, update to Cypress driver to
handle Gen5 (in addition to Gen3) devices, and number of other fixups
to various drivers as well as input core"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: elan_i2c - fix wrong %p extension
Input: evdev - do not queue SYN_DROPPED if queue is empty
Input: gscps2 - fix MODULE_DEVICE_TABLE invocation
Input: synaptics - use dmax in input_mt_assign_slots
Input: pxa27x_keypad - remove unnecessary ARM includes
Input: ti_am335x_tsc - replace delta filtering with median filtering
ARM: dts: AM335x: Make charge delay a DT parameter for TSC
Input: ti_am335x_tsc - read charge delay from DT
Input: ti_am335x_tsc - remove udelay in interrupt handler
Input: ti_am335x_tsc - interchange touchscreen and ADC steps
Input: MT - add support for balanced slot assignment
Input: drv2667 - remove wrong and unneeded drv2667-haptics modalias
Input: drv260x - remove wrong and unneeded drv260x-haptics modalias
Input: cap11xx - remove wrong and unneeded cap11xx modalias
Input: sun4i-ts - add support for touchpanel controller on A31
Input: serio - add support for Alwinner A10/A20 PS/2 controller
Input: gtco - use sign_extend32() for sign extension
Input: elan_i2c - verify firmware signature applying it
Input: elantech - remove stale comment from Kconfig
Input: cyapa - off by one in cyapa_update_fw_store()
...
This patch makes the initial changes required to workaround TSC-false
pen-up interrupts. It is required to implement these changes in order to
remove udelay in the TSC interrupt handler and false pen-up events. The
charge step is to be executed immediately after sampling X+. Hence TSC is
made to use higher numbered steps (steps 5 to 16 for 5 co-ordinate
readouts, 4 wire TSC configuration) and ADC to use lower ones. Further X
co-ordinate readouts must be the last to be sampled, thus co-ordinates are
sampled in the order Y-Z-X.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[vigneshr@ti.com: Ported the patch from v3.12 to v3.19rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* ad799x fix ad7991/ad7995/ad7999 setup as they do not have a configuration
register to write to. It is written during the convesion sequence. As
such we don't want to write to it at other times.
* Fix iio_channel_read utility function to return to ensure it is apparent
if the relevant element is not there. This avoids using a wrong value
if some channels have the element and others do not.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7f+n
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.19a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 3.19 cycle.
* ad799x fix ad7991/ad7995/ad7999 setup as they do not have a configuration
register to write to. It is written during the convesion sequence. As
such we don't want to write to it at other times.
* Fix iio_channel_read utility function to return to ensure it is apparent
if the relevant element is not there. This avoids using a wrong value
if some channels have the element and others do not.
When xilinx-xadc is used with hwmon driver to read voltage, offset used
for temperature is always applied whatever the channel.
iio_channel_read must return an error to avoid offset for channel
without IIO_CHAN_INFO_OFFSET property.
Signed-off-by: Fabien Proriol <fabien.proriol@jdsu.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here's the big staging tree pull request for 3.19-rc1.
We continued to delete more lines than were added, always a good thing,
but not at a huge rate this release, only about 70k lines removed
overall mostly from removing the horrid bcm driver.
Lots of normal staging driver cleanups and fixes all over the place,
well over a thousand of them, the shortlog shows all the horrid details.
The "contentious" thing here is the movement of the Android binder code
out of staging into the "real" part of the kernel. This is code that
has been stable for a few years now and is working as-is in the tens of
millions of devices with no issues. Yes, the code is horrid, and the
userspace api leaves a lot to be desired, but it's not going to change
due to legacy issues that we have no control over. Because so many
devices and companies rely on this, and the code is stable, might as
well promote it out of staging.
This was all discussed at the Linux Plumbers conference, and everyone
participating agreed that this was the best way forward.
There is work happening to replace the binder code with something new
that is happening right now, but I don't expect to see the results of
that work for another year at the earliest. If that ever happens, and
Android switches over to it, I'll gladly remove this version.
As for maintainers, I'll be glad to maintain this code, I've been doing
it for the past few years with no problems. I'll send a MAINTAINERS
entry for it before 3.19-final is out, still need to talk to the Google
developers about if they are willing to help with it or not, last I
checked they were, which was good.
All of these patches have been in linux-next for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSPICkACgkQMUfUDdst+yksdwCfSLE9VUy1o2sAPDRe+J3bQced
EWEAoL3RtnejKbo5tHS2IT69pLrwiIDS
=YXyM
-----END PGP SIGNATURE-----
Merge tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big staging tree pull request for 3.19-rc1.
We continued to delete more lines than were added, always a good
thing, but not at a huge rate this release, only about 70k lines
removed overall mostly from removing the horrid bcm driver.
Lots of normal staging driver cleanups and fixes all over the place,
well over a thousand of them, the shortlog shows all the horrid
details.
The "contentious" thing here is the movement of the Android binder
code out of staging into the "real" part of the kernel. This is code
that has been stable for a few years now and is working as-is in the
tens of millions of devices with no issues. Yes, the code is horrid,
and the userspace api leaves a lot to be desired, but it's not going
to change due to legacy issues that we have no control over. Because
so many devices and companies rely on this, and the code is stable,
might as well promote it out of staging.
This was all discussed at the Linux Plumbers conference, and everyone
participating agreed that this was the best way forward.
There is work happening to replace the binder code with something new
that is happening right now, but I don't expect to see the results of
that work for another year at the earliest. If that ever happens, and
Android switches over to it, I'll gladly remove this version.
As for maintainers, I'll be glad to maintain this code, I've been
doing it for the past few years with no problems. I'll send a
MAINTAINERS entry for it before 3.19-final is out, still need to talk
to the Google developers about if they are willing to help with it or
not, last I checked they were, which was good.
All of these patches have been in linux-next for a while with no
reported issues"
* tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1382 commits)
Staging: slicoss: Fix long line issues in slicoss.c
staging: rtl8712: remove unnecessary else after return
staging: comedi: change some printk calls to pr_err
staging: rtl8723au: hal: Removed the extra semicolon
lustre: Deletion of unnecessary checks before three function calls
staging: lustre: fix sparse warnings: static function declaration
staging: lustre: fixed sparse warnings related to static declarations
staging: unisys: remove duplicate header
staging: unisys: remove unneeded structure
staging: ft1000 : replace __attribute ((__packed__) with __packed
drivers: staging: rtl8192e: Include "asm/unaligned.h" instead of "access_ok.h" in "rtl819x_BAProc.c"
Drivers:staging:rtl8192e: Fixed checkpatch warning
Drivers:staging:clocking-wizard: Added a newline
staging: clocking-wizard: check for a valid clk_name pointer
staging: rtl8723au: Hal_InitPGData() avoid unnecessary typecasts
staging: rtl8723au: _DisableAnalog(): Avoid zero-init variables unnecessarily
staging: rtl8723au: Remove unnecessary wrapper _ResetDigitalProcedure1()
staging: rtl8723au: _ResetDigitalProcedure1_92C() reduce code obfuscation
staging: rtl8723au: Remove unnecessary wrapper _DisableRFAFEAndResetBB()
staging: rtl8723au: _DisableRFAFEAndResetBB8192C(): Reduce code obfuscation
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The ad7991/ad7995/ad7999 does not have a configuration register like the
other devices that can be written and read. The configuration is written as
part of the conversion sequence.
Fixes: 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe and reset alert status on probe")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* acpi-video:
ACPI / video: Run _BCL before deciding registering backlight
* acpi-pmic:
ACPI / PMIC: AXP288: support virtual GPIO in ACPI table
ACPI / PMIC: support PMIC operation region for XPower AXP288
ACPI / PMIC: support PMIC operation region for CrystalCove
iio/axp288_adc: remove THIS_MODULE owner
mfd/axp20x: avoid irq numbering collision
iio: adc: Add module device table for autoloading
iio: adc: Add support for axp288 adc
mfd: axp20x: Extend axp20x to support axp288 pmic
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/iio/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
This is no longer needed in that platform driver_register will do it.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the module device id table so that the driver can be automatically
loaded once the platform device is created.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Set the threshold to low by default. With this thresholds any movement
on the device with this sensor will generate event.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change event spec direction from
IIO_EV_DIR_RISING | IIO_EV_DIR_FALLING
to
IIO_EV_DIR_EITHER
Suggested-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This chip is capable to identify motion across x, y and z axes. So
send different events.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When mode set fails due to some transient failures, it will atleast
reset the state of runtime usage count and also let the runtime
suspend retry from the driver framework.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change event spec direction from
IIO_EV_DIR_RISING | IIO_EV_DIR_FALLING
to
IIO_EV_DIR_EITHER
Suggested-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This chip is capable to identify motion across x, y and z axes. So
send different events.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change the mode to push/pull type instead of open drain as some
platforms fails to drive the GPIO pin with open drain.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When mode set fails due to some transient failures, it will atleast
reset the state of runtime usage count and also let the runtime
suspend retry from the driver framework.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mcb_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently, we get the new GSEL bits by OR-ing the old values
with the new ones. This only works first time when the old
values are 0.
Startup:
* GSEL0 = 0, GSEL1 = 0
Set range to 4G: (GSEL0 = 1, GSEL1 = 0)
* GSEL0 = 0 | 1 = 1
* GSEL1 = 0 | 0 = 0
* correct
Change range to 2G: (GSEL0 = 0, GSEL1 = 0)
* GSEL0 = 1 | 0 = 1
* GSEL1 = 0 | 0 = 0
* wrong, GSEL0 should be 0
This has the nice effect that we can use the full scale range,
exported in in_accel_scale_available.
Fixes: a735e3d7f0 (iio: accel: kxcjk-1013: Set adjustable range)
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New drivers / supported parts
* rockchip - rk3066-tsadc variant
* si7020 humidity and temperature sensor
* mcp320x - add mcp3001, mcp3002, mcp3004, mcp3008, mcp3201, mcp3202
* bmp280 pressure and temperature sensor
* Qualcomm SPMI PMIC current ADC driver
* Exynos_adc - support exynos7
New features
* vf610-adc - add temperature sensor support
* Documentation of current attributes, scaled pressure, offset and
scaled humidity, RGBC intensity gain factor and scale applied to
differential voltage channels.
* Bring iio_event_monitor up to date with newer modifiers.
* Add of_xlate function to allow for complex channel mappings from the
device tree.
* Add -g parameter to generic_buffer example to allow for devices with
directly fed (no trigger) buffers.
* Move exynos driver over to syscon for PMU register access.
Cleanups, fixes for new drivers
* lis3l02dq drop an unneeded else.
* st sensors - renam st_sensors to st_sensor_settings (for clarity)
* st sensors - drop an unused parameter from all the probe utility
functions.
* vf610 better error handling and tidy up.
* si7020 - cleanups following merge
* as3935 - drop some unnecessary semicolons.
* bmp280 - fix the pressure calculation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=BDOo
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.19a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, features and cleanups for IIO in the 3.19 cycle.
New drivers / supported parts
* rockchip - rk3066-tsadc variant
* si7020 humidity and temperature sensor
* mcp320x - add mcp3001, mcp3002, mcp3004, mcp3008, mcp3201, mcp3202
* bmp280 pressure and temperature sensor
* Qualcomm SPMI PMIC current ADC driver
* Exynos_adc - support exynos7
New features
* vf610-adc - add temperature sensor support
* Documentation of current attributes, scaled pressure, offset and
scaled humidity, RGBC intensity gain factor and scale applied to
differential voltage channels.
* Bring iio_event_monitor up to date with newer modifiers.
* Add of_xlate function to allow for complex channel mappings from the
device tree.
* Add -g parameter to generic_buffer example to allow for devices with
directly fed (no trigger) buffers.
* Move exynos driver over to syscon for PMU register access.
Cleanups, fixes for new drivers
* lis3l02dq drop an unneeded else.
* st sensors - renam st_sensors to st_sensor_settings (for clarity)
* st sensors - drop an unused parameter from all the probe utility
functions.
* vf610 better error handling and tidy up.
* si7020 - cleanups following merge
* as3935 - drop some unnecessary semicolons.
* bmp280 - fix the pressure calculation.
Because IIO_EV_DIR_* are not bitmasks but enums,
IIO_EV_DIR_RISING | IIO_EV_DIR_FALLING is not equal
with IIO_EV_DIR_EITHER.
This could lead to potential misformatted sysfs attributes
like:
* in_accel_x_thresh_(null)_en
* in_accel_x_thresh_(null)_period
* in_accel_x_thresh_(null)_value
or even memory corruption.
Fixes: b4b491c083 (iio: accel: kxcjk-1013: Support threshold)
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix the compiler error when the CONFIG_PM_OPS flag is not set.
drivers/iio/light/tsl4531.c:235:8: error: ‘tsl4531_suspend’ undeclared here (not in a function)
drivers/iio/light/tsl4531.c:235:8: error: ‘tsl4531_resume’ undeclared here (not in a function)
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use byte_for_channel as iterator to properly initialize the buffer.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: <Stable@vger.kernel.org>
According to the datasheet and as defined in struct bmp280_comp_press, dig_p1 is
of type u16, while dig_p2 to dig_p9 are of type s16. In
bmp280_read_compensation_press(), values read from the device were treated as
the wrong type.
In bmp280_read_press() the fractional part of the measured pressure is
calculated wrong. A better way is to use *val for the raw pressure and *val2 for
the quotient and let the core do the proper conversion using IIO_VAL_FRACTIONAL.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ADC on exynos7 is quite similar to ADCv2. The differences are as
follows:
- exynos7-adc has 8 input channels (as against 10 in ADCv2).
- exynos7 does not include an ADC PHY control register.
- Some ADC_CON2 register bits being used in ADCv2 are listed as
reserved in exynos7-adc. This results in a different init_hw
function for exynos7.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch updates the IIO based ADC driver to use syscon and regmap
APIs to access and use PMU registers instead of remapping the PMU
registers in the driver.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
To: linux-iio@vger.kernel.org
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The current ADC is peripheral of Qualcomm SPMI PMIC chips. It has
16 bits resolution and register space inside PMIC accessible across
SPMI bus.
The driver registers itself through IIO interface.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In si7020_read_raw() the pointer to the i2c client was obtained as second level
pointer, although a simple pointer is appropriate.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When reading temperature or humidity values, a shift of two bits to the right
needs to be applied, and only for the humidity channel a mask of the lower
12 bits needs to be applied. This reduces code repetition.
During probe, i2c_set_clientdata() was used, although its counterpart was not,
so drop it.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When #iio-cells is greater than '0', the driver could provide
a custom of_xlate function that reads the *args* and returns
the appropriate index in registered IIO channels array.
Add simple translation function, suitable for the most 1:1
mapped channels in IIO chips, and use it when driver did not
provide custom implementation.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The proper way to divide two signed 64-bit values is to use div64_s64.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* ad5933 - fix a null pointer dereference due to an old change that prevents
different channels being registered for the buffer and used for sysfs
interfaces.
* ad5933 - Drop a bonus _raw from attribute names.
* st-sensors - Makes sure the correct number of elements are copied when
filling a local buffer copy.
* mxs-lradc - Disable clocks in a failure path during probe so they aren't
left running.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TYUO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.18a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 3.18 cycle.
* ad5933 - fix a null pointer dereference due to an old change that prevents
different channels being registered for the buffer and used for sysfs
interfaces.
* ad5933 - Drop a bonus _raw from attribute names.
* st-sensors - Makes sure the correct number of elements are copied when
filling a local buffer copy.
* mxs-lradc - Disable clocks in a failure path during probe so they aren't
left running.
There is no need to pass a 'fake' return value when platform_get_irq() fails.
Propagate the real error instead.
While at it, only consider negative numbers returned by platform_get_irq()
as error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Platform driver for X-Powers AXP288 ADC, which is a sub-device of the
customized AXP288 PMIC for Intel Baytrail-CR platforms. GPADC device
enumerates as one of the MFD cell devices. It uses IIO infrastructure
to communicate with userspace and consumer drivers.
Usages of ADC channels include battery charging and thermal sensors.
Based on initial work by:
Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support to the Industrial IO subsystem
for the Silicon Labs Si7013/20/21 Relative Humidity and
Temperature Sensors.
Website: http://www.silabs.com/products/sensors/humidity-sensors/Pages/si7013-20-21.aspx
These are i2c devices which measure relative humidity
and temperature and all use the same protocol. The
Si7013 has an additional input with programmable
linearization which is not supported because that's
complicated and I didn't need it.
Signed-off-by: David Barksdale <dbarksdale@uplogix.com>
--
Changes since v1:
* Renamed to si7020 and replaced Si701x/2x with Si7013/20/21.
* Removed unneeded mutex.
* Pre-computed floating-point constant expressions.
* Removed address_list and I2C_CLASS_HWMON.
Changes since v2:
* Return correct raw sensor values.
* Rename dev variable to indio_dev.
* Issue a software reset command during probe.
* Un-broke string literal.
Changes since v3:
* enum changed to #define
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
No need to call the SIMPLE_DEV_PM_OPS() macro in several lines.
It can fit into the 80-column range.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If clk_prepare_enable() fails we should disable the regulator that was
previously enabled.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There is no need to pass the error clock code to the variable 'ret'.
Just return the error directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
