Adds an optional infrustructure component to bridge that would allow
native vlan filtering in the bridge. Each bridge port (as well
as the bridge device) now get a VLAN bitmap. Each bit in the bitmap
is associated with a vlan id. This way if the bit corresponding to
the vid is set in the bitmap that the packet with vid is allowed to
enter and exit the port.
Write access the bitmap is protected by RTNL and read access
protected by RCU.
Vlan functionality is disabled by default.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge link detection should follow the operational state
of the lower device, rather than the carrier bit. This allows devices
like tunnels that are controlled by userspace control plane to work
with bridge STP link management.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netdev_set_master faild in br_add_if, we should
call br_netpoll_disable to do some cleanup jobs,such
as free the memory of struct netpoll which allocated
in br_netpoll_enable.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add comments on why we don't notify NETDEV_RELEASE.
Cc: David Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ensures that bridges created with brctl(8) or ioctl(2) directly
also carry IFLA_LINKINFO when dumped over netlink. This also allows
to create a bridge with ioctl(2) and delete it with RTM_DELLINK.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to cleanup bridge device timers and ports when being bridge
device is being removed via netlink.
This fixes the problem of observed when doing:
ip link add br0 type bridge
ip link set dev eth1 master br0
ip link set br0 up
ip link del br0
which would cause br0 to hang in unregister_netdev because
of leftover reference count.
Reported-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is added to a bridge, the old code would send the new neighbor
netlink message before the subsequent new link message. This bug makes
it difficult to use the monitoring API in an application.
This code changes the ordering to add the forwarding entry
after the port is setup. One of the error checks (for invalid address)
is moved earlier in the process to avoid having to do unwind.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
iboe_get_rate was previously ->get_settings() called unlocked. This
fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
problem. Also fixed by calling __dev_get_by_index() instead of
dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
so bnx2fc_if_create() and fcoe_if_create() are called locked as they
are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
around it and __ethtool_get_settings() call
v1->v2:
add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since these checks and initialization are done in
dev_ethtool_get_settings called later on, remove this redundancy.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Beulich reported a possible net_device leak in bridge code after
commit bb900b27a2 (bridge: allow creating bridge devices with netlink)
Reported-by: Jan Beulich <JBeulich@novell.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ensures the neighbor entries associated with the bridge
dev are flushed, also invalidating the associated cached L2 headers.
This means we br_add_if/br_del_if ports to implement hand-over and
not wind up with bridge packets going out with stale MAC.
This means we can also change MAC of port device and also not wind
up with bridge packets going out with stale MAC.
This builds on Stephen Hemminger's patch, also handling the br_del_if
case and the port MAC change case.
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a new device is added to a bridge, the ethernet address of the
bridge network device may change. When the address changes, the
appropriate callback is called, but with the wrong device argument.
The address of the bridge device (ie br0) changes not the address
of the device being passed to add_if (ie eth0).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the old days, we used to access dev->master in __netif_receive_skb()
in a rcu_read_lock section.
So one synchronize_net() call was needed in netdev_set_master() to make
sure another cpu could not use old master while/after we release it.
We now use netdev_rx_handler infrastructure and added one
synchronize_net() call in bond_release()/bond_release_all()
Remove the obsolete synchronize_net() from netdev_set_master() and add
one in bridge del_nbp() after its netdev_rx_handler_unregister() call.
This makes enslave -d a bit faster.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jiri Pirko <jpirko@redhat.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous patch I added NETDEV_JOIN, now
we can notify netconsole when adding a device to a bridge too.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().
All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: netdev_update_features() needs only rtnl_lock as br->port_list
is only changed while holding it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink device ops to allow creating bridge device via netlink.
This works in a manner similar to vlan, macvlan and bonding.
Example:
# ip link add link dev br0 type bridge
# ip link del dev br0
The change required rearranging initializtion code to deal with
being called by create link. Most of the initialization happens
in br_dev_setup, but allocation of stats is done in ndo_init callback
to deal with allocation failure. Sysfs setup has to wait until
after the network device kobject is registered.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac address of the bridge device may be changed when a new interface
is added to the bridge. If this happens, then the bridge needs to call
the network notifiers to tickle any other systems that care. Since bridge
can be a module, this also means exporting the notifier function.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce printk() levels to KERN_INFO in netdev_fix_features() as this will
be used by ethtool and might spam dmesg unnecessarily.
This converts the function to use netdev_info() instead of plain printk().
As a side effect, bonding and bridge devices will now log dropped features
on every slave device change.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Ben Hutchings: we presumably won't be defining features that
can only be enabled on 64-bit architectures.
Occurences found by `grep -r` on net/, drivers/net, include/
[ Move features and vlan_features next to each other in
struct netdev, as per Eric Dumazet's suggestion -DaveM ]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_port_get() renamed to br_port_get_rtnl() to make clear RTNL is held.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro br_port_exists() is not enough protection when only
RCU is being used. There is a tiny race where other CPU has cleared port
handler hook, but is bridge port flag might still be set.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bridge port is offline, don't call ethtool to query speed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The carrier check is not called from work queue in current code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register net_bridge_port pointer as rx_handler data pointer. As br_port is
removed from struct net_device, another netdev priv_flag is added to indicate
the device serves as a bridge port. Also rcuized pointers are now correctly
dereferenced in br_fdb.c and in netfilter parts.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add possibility to register rx_handler data pointer along with a rx_handler.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are multiple problems with the newly added netpoll support:
1) Use-after-free on each netpoll packet.
2) Invoking unsafe code on netpoll/IRQ path.
3) Breaks when netpoll is enabled on the underlying device.
This patch fixes all of these problems. In particular, we now
allocate proper netpoll structures for each underlying device.
We only allow netpoll to be enabled on the bridge when all the
devices underneath it support netpoll. Once it is enabled, we
do not allow non-netpoll devices to join the bridge (until netpoll
is disabled again).
This allows us to do away with the npinfo juggling that caused
problem number 1.
Incidentally this patch fixes number 2 by bypassing unsafe code
such as multicast snooping and netfilter.
Reported-by: Qianfeng Zhang <frzhang@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
What this patch does is it removes two receive frame hooks (for bridge and for
macvlan) from __netif_receive_skb. These are replaced them with a single
hook for both. It only supports one hook per device because it makes no
sense to do bridging and macvlan on the same device.
Then a network driver (of virtual netdev like macvlan or bridge) can register
an rx_handler for needed net device.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build when CONFIG_SYSFS is not enabled:
net/bridge/br_if.c:136: error: 'struct net_bridge_port' has no member named 'sysfs_name'
Note: dev->name == sysfs_name except when change name is in
progress, and we are protected from that by RTNL mutex.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Links for each port are created in sysfs using the device
name, but this could be changed after being added to the
bridge.
As well as being unable to remove interfaces after this
occurs (because userspace tools don't recognise the new
name, and the kernel won't recognise the old name), adding
another interface with the old name to the bridge will
cause an error trying to create the sysfs link.
This fixes the problem by listening for NETDEV_CHANGENAME
notifications and renaming the link.
https://bugzilla.kernel.org/show_bug.cgi?id=12743
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move code around so that the ifdef for NETPOLL_CONTROLLER don't have to
show up in main code path. The control functions should be in helpers
that are only compiled if needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the previous patch, make bridge support netpoll by:
1) implement the 2 methods to support netpoll for bridge;
2) modify netpoll during forwarding packets via bridge;
3) disable netpoll support of bridge when a netpoll-unabled device
is added to bridge;
4) enable netpoll support when all underlying devices support netpoll.
Cc: David Miller <davem@davemloft.net>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The shared packet statistics are a potential source of slow down
on bridged traffic. Convert to per-cpu array, but only keep those
statistics which change per-packet.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch hooks up the bridge start/stop and add/delete/disable
port functions to the new multicast module.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unused age_list member from the net_bridge
structure.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__net_init/__net_exit are apparently not going away, so use them
to full extent.
In some cases __net_init was removed, because it was called from
__net_exit code.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of people have tried to add a wireless interface
(in managed mode) to a bridge and then complained that it
doesn't work. It cannot work, however, because in 802.11
networks all packets need to be acknowledged and as such
need to be sent to the right address. Promiscuous doesn't
help here. The wireless address format used for these
links has only space for three addresses, the
* transmitter, which must be equal to the sender (origin)
* receiver (on the wireless medium), which is the AP in
the case of managed mode
* the recipient (destination), which is on the APs local
network segment
In an IBSS, it is similar, but the receiver and recipient
must match and the third address is used as the BSSID.
To avoid such mistakes in the future, disallow adding a
wireless interface to a bridge.
Felix has recently added a four-address mode to the AP
and client side that can be used (after negotiating that
it is possible, which must happen out-of-band by setting
up both sides) for bridging, so allow that case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge code assumes ethernet addressing, so be more strict in
the what is allowed. This showed up when GRE had a bug and was not
using correct address format.
Add some more comments for increased clarity.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Speedup module unloading by factorizing synchronize_rcu() calls
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential double-kfree in net/bridge/br_if.c. If br_fdb_insert
fails, then the kobject is put back (which calls kfree due to the kobject
release), and then kfree is called again on the net_bridge_port. This
patch fixes the crash.
Thanks to Stephen Hemminger for the one-line fix.
Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.
To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.
# cat /sys/class/net/wlan0/uevent
DEVTYPE=wlan
INTERFACE=wlan0
IFINDEX=5
This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.
The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
