Taken from Realtek's 8.006.00 r8168 driver.
I have left some bits related to jumbo frame aside for now.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
This part of the driver should be reasonably in line with Realtek's
8.006.00 driver.
I have left some bits related to jumbo frame and optional features
aside for now.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Broadly speaking the 8168c* share some common code which will
be factored in __rtl_hw_start_8168cp. The 8168b* share some
code too but it will be a bit different.
Any change of behavior should be confined to the currently
unidentified 8168 chipsets. They will not be applied the Tx
performance tweak and will emit a warning instead.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
I can not argue strongly for (or against) a specific ordering
on a purely technical ground but the patch avoids to swallow
Realtek's changes in one big, hard-to-read gulp.
Let aside the way the RxConfig register is written (see
rtl_set_rx_tx_config_registers / RxConfig / rtl_set_rx_mode),
this change brings the registers write ordering closer with
Realtek's driver one (version 8.006.00) for the 8168 chipsets.
More 8168 specific code which touches the Configx registers will
be added in the section covered by Cfg9346_UnLock / Cfg9346_Lock.
This code should not be the cause of regression for 810x and
8110 users.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The new parameters are synced with Realtek's driver
version 8.006.00.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The modified parameters are synced with Realtek's driver
version 8.006.00.
The change should only be noticeable with some 8168c.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
This is typically needed when some other OS puts the PHY
to sleep due to the disabling of WOL options in the BIOS
of the system.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Chiaki Ishikawa <chiaki.ishikawa@ubin.jp>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Cc: RyanKao <ryankao@realtek.com.tw>
When deleting an SPD entry using SADB_X_SPDDELETE, c.data.byid is not
initialized to zero in pfkey_spddelete(). Thus, key_notify_policy()
responds with a PF_KEY message of type SADB_X_SPDDELETE2 instead of
SADB_X_SPDDELETE.
Signed-off-by: Tobias Brunner <tobias.brunner@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a special request for serialisation purposes and get rid of the
awkward ide_spin_wait_hwgroup(). This also involves converting the
ide_devset structure so it can be shared by the /proc and the ioctl code.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
[bart: use rq->cmd[] directly]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
* IDE{FLOPPY,TAPE}_WAIT_CMD -> WAIT_{FLOPPY,TAPE}_CMD
* Use enum for WAIT_* defines.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_do_test_unit_ready() helper and convert ide-{floppy,tape}.c
to use it.
* Remove no longer used idetape_create_test_unit_ready_cmd().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_do_start_stop() helper and convert ide-{floppy,tape}.c
to use it.
* Remove no longer used idefloppy_create_start_stop_cmd()
and idetape_create_load_unload_cmd().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set IDE_AFLAG_NO_DOORLOCK in idetape_get_mode_sense_result(), check it
in ide_tape_set_media_lock() and cleanup idetape_create_prevent_cmd().
* Set IDE_AFLAG_NO_DOORLOCK in ide_floppy_create_read_capacity_cmd() and
check it instead of IDE_AFLAG_CLIK_DRIVE in ide_floppy_set_media_lock().
* Add ide_set_media_lock() helper and convert ide-{floppy,tape}.c to use it.
* Remove no longer used ide*_create_prevent_cmd()/ide*_set_media_lock().
* Update comment in <linux/ide.h> accordingly.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_AFLAG_{SRFP,WP} drive->atapi_flags and use them
instead of ->{srfp,wp} struct ide_floppy_obj fields.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_queue_pc_tail() and convert ide-{floppy,tape}.c to use it
instead of ide*_queue_pc_tail().
* Remove no longer used ide*_queue_pc_tail().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move REQ_IDETAPE_* enums to <linux/ide.h>.
* Add ide_queue_pc_head() and convert ide-{floppy,tape}.c to use it
instead of ide*_queue_pc_head().
* Remove no longer used ide*_queue_pc_head().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_PC_BUFFER_SIZE define.
* Add ide_init_pc() and convert ide-{floppy,tape}.c to use it
instead of ide*_init_pc().
* Remove no longer used IDE*_PC_BUFFER_SIZE and ide*_init_pc().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_tape_set_media_lock() helper and convert idetape_mtioctop(),
idetape_chrdev_open() and idetape_chrdev_release() to use it.
There should be no functional changes caused by this patch (it is
OK to modify ->door_locked if idetape_create_prevent_cmd() fails).
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_floppy_set_media_lock() helper and convert idefloppy_open(),
idefloppy_release() and ide_floppy_lockdoor() to use it.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ->io_buffers method return number of bytes transferred.
* Use ide_end_request() instead of idefloppy_end_request()
in ide_floppy_io_buffers() and then move the call out to
ide_pc_intr().
* Add ide_io_buffers() helper and convert ide-{floppy,scsi}.c
to use it instead of ide*_io_buffers().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Only MODE_SENSE_CURRENT (0x00) is ever used so just remove
these defines and then drop no longer needed 'type' argument
from idefloppy_create_mode_sense_cmd().
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct ide_atapi_pc queued_pc' to struct ide_{floppy,tape}_obj
and switch ide*_do_request() to use it (there can be only one active
request for a given device).
* Add 'struct ide_atapi_pc request_sense_pc' to struct ide_*_obj
and switch ide*_retry_pc() to use it.
* Remove needless {floppy,tape}->pc assignment from ide*_setup().
* Remove no longer needed ide*_next_pc_storage(), pc_stack[],
rq_stack_index, IDE*_PC_STACK and DBG_PC_STACK.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct request request_sense_rq' to struct ide_{floppy,tape}_obj
and switch ide*_retry_pc() to use it (there can be only one REQUEST SENSE
request active for a given device).
* Remove no longer needed ide*_next_rq_storage(), rq_stack[]
and rq_stack_index.
* DBG_PCRQ_STACK -> DBG_PC_STACK
* Update comments for IDE*_PC_STACK and idetape_queue_pc_{head,tail}().
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Avoid probing the io-ports in case an IDE PCI controller is present and it
uses the legacy iobases. If we still want to enforce the probing, we do
ide_generic.probe_mask=0x3f
on the kernel command line. The iobase checking code is
adapted from drivers/ata/pata_legacy.c after converting hex
pci ids into their corresponding macros in <linux/pci_ids.h>.
Also, check only BAR0/2 resources since those are guaranteed
by the workaround in drivers/pci/probe.c:pci_setup_device().
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
[bart: trivial printk() fixups]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use hwif->sg_table for pio transfers instead of fumbling
with block layer internals in the driver. Also, make debug
statements more informative in .._do_request() while at it.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: fixup pc->b_count in idefloppy_blockpc_cmd()]
[bart: add missing include (noticed by Stephen Rothwell)]
[bart: map hwif->sg_{table,nents} on pc->{sg,sg_cnt} (multi-IRQs-per-sg fix)]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
idetape_init_rq() is only used in idetape_queue_pc_head()
so inline it there.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out IDEFLOPPY_IOCTL_FORMAT_* ioctls handling from
idefloppy_ioctl() to ide_floppy_format_ioctl().
While at it:
* Pass 'drive' instead of 'floppy' to ide_floppy_format_unit().
* idefloppy_get_format_progress() -> ide_floppy_get_format_progress()
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_check_atapi_device() to ide-atapi.c and convert
ide-{floppy,tape}.c to use it instead of ide*_identify_device().
While at it:
* Add DRV_NAME defines to ide-{floppy,tape}.c.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix intendation for the main 'switch ()'.
* 'switch ()' -> 'if ()' for HDIO_DRIVE_TASKFILE case.
* Move HDIO_SET_NICE case under HDIO_GET_NICE one.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add struct ide_ioctl_devset representing ioctl device setting.
* Add ide_setting_ioctl() helper for matching given ioctl
and its parameters against table of ioctl device settings.
* Convert ide_setting_ioctl() and idedisk_ioctl() to use
ide_setting_ioctl().
* Un-export ide_setting_mtx.
While at it:
* {get,set}_lba_addressing() -> {get,set}_addressing()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Keep pointer to ->init_chipset method also in
struct ide_host and set it in ide_host_alloc_all().
* Add ide_pci_suspend() and ide_pci_resume() helpers
(default ->suspend and ->resume implementations).
* ->init_chipset can no longer be marked __devinit.
* Add proper PCI PM support to IDE PCI host drivers
(rz1000.c and tc86c001.c are skipped for now since
they need to be converted from using ->init_hwif
to use ->init_chipset instead).
v2:
* Cleanup CONFIG_PM #ifdef-s per akpm's suggestion.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out disabling of "fast interrupt" prediction from
init_hwif_hpt366() to hpt3xx_disable_fast_irq() helper.
* Use hpt3xx_disable_fast_irq() in ->init_chipset instead of
->init_hwif method.
This is a preparation for adding proper PCI PM support.
While at it:
* Cache chip type in chip_type variable in hpt3xx_disable_fast_irq().
There should be no functional changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Rename lba_capacity_is_ok() to ata_id_is_lba_capacity_ok()
and move it to <linux/ata.h> (remove needless parens while at it).
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Rename ide_id_to_hd_driveid() to ata_id_to_hd_driveid()
and move it to <linux/ata.h>.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ata_id_is_cfa() in do_identify() instead of open-coding
check for CompactFlash devices (the inline helper also takes
care of detecting CFs advertising themselves as ATA disks).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ata_id_flush_ext_enabled() inline helper to <linux/ata.h>.
* ide_id_has_flush_cache_ext() -> ata_id_flush_ext_enabled()
The latter one also checks if the command is marked as
supported in word 83 and validity of words 83 & 86.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ata_id_flush_enabled() inline helper to <linux/ata.h>.
* ide_id_has_flush_cache() -> ata_id_flush_enabled()
The latter one also checks if the command is marked as
supported in word 83 and validity of words 83 & 86.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All devices supporting CACHE FLUSH EXT command should also support
CACHE FLUSH command so it is sufficient to check only for CACHE FLUSH
in ide_id_has_flush_cache().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ata_id_lba48_enabled() inline helper to <linux/ata.h>.
* idedisk_supports_lba48() -> ata_id_lba48_enabled()
The latter one also checks validity of words 83 & 86.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use optimized ATA version check from Sergei in ata_id_is_sata().
* ide_dev_is_sata() -> ata_id_is_sata()
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove (id[ATA_ID_FIELD_VALID] & 2) check from ide_dev_has_iordy()
(it is for validity of words 64-70, IORDY is in word 49).
* ide_dev_has_iordy() -> ata_id_has_iordy()
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out HDIO_{GET,SET}_NICE ioctl handling from
generic_ide_ioctl() to ide_{get,set}_nice_ioctl().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use drive->media and drive->scsi to check if ->dsc_overlap
can be set by HDIO_SET_NICE ioctl in generic_ide_ioctl().
* Remove unused ->supports_dsc_overlap field from ide_driver_t.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
