The return type has more than two values, but it can validly
only ever return TX_DROP and TX_CONTINUE, so use a bool
instead of ieee80211_tx_result.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
addba_req_num[tid] is supposed to have the count of consecutive
addba request attempts on 'tid' which failed. This count is checked
against a retry threshold (3 times) before starting the addba negotiation.
This patch fixes the way this addba count is incremented/reset and thereby
avoids indefinite addba attempts.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to handle powersave frames properly we had needed
to pass these out to the device queues again, and introduce
the skb->requeue bit. This, however, also has unnecessary
overhead by needing to 'clean up' already tried frames, and
this clean-up code is also buggy when software encryption
is used.
Instead of sending the frames via the master netdev queue
again, simply put them into the pending queue. This also
fixes a problem where frames for that particular station
could be reordered when some were still on the software
queues and older ones are re-injected into the software
queue after them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 is checking is the skb is aligned on 32 bit boundary.
But it is checking against ethernet header, whereas Linux expect IP
header aligned. And ethernet ether size is 6*2+2=14, so aligning
ethernet header make IP header unaligned.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The minstrel rate controller periodically looks up rate indexes in
a sampling table. When accessing a specific row and column, minstrel
correctly does a bounds check which, on the surface, appears to handle
the case where mi->n_rates < 2. However, mi->sample_idx is actually
defined as an unsigned, so the right hand side is taken to be a huge
positive number when negative, and the check will always fail.
Consequently, the RC will overrun the array and cause random memory
corruption when communicating with a peer that has only a single rate.
The max value of mi->sample_idx is around 25 so casting to int should
have no ill effects.
Without the change, uptime is a few minutes under load with an AP
that has a single hard-coded rate, and both the AP and STA could
potentially crash. With the change, both lasted 12 hours with a
steady load.
Thanks to Ognjen Maric for providing the single-rate clue so I could
reproduce this.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=12490 on the
regression list (also http://bugzilla.kernel.org/show_bug.cgi?id=13000).
Cc: stable@kernel.org
Reported-by: Sergey S. Kostyliov <rathamahata@gmail.com>
Reported-by: Ognjen Maric <ognjen.maric@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwm doesn't depend on cfg80211 or wireless extensions
* rndis wlan selects cfg80211 - needs to depend
* mac80211 selects cfg80211 - needs to depend
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be easier on drivers and users, have cfg80211 register an
rfkill structure that drivers can access. When soft-killed,
simply take down all interfaces; when hard-killed the driver
needs to notify us and we will take down the interfaces
after the fact. While rfkilled, interfaces cannot be set UP.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces new cfg80211 API to set the TX power
via cfg80211, puts the wext code into cfg80211 and updates
mac80211 to use all that. The -ENETDOWN bits are a hack but
will go away soon.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the SME requests to associate to an open AP
ieee80211_sta_set_extra_ie() can be called with zero IE
length. When this happens or when the extra IE has already
been set -EALREADY is passed down and the supplicant will
complain that the operation is already in progress and it will
not let us associate. We correct this by treating -EALREADY
from ieee80211_sta_set_extra_ie() as a success just as we do
for wext.
Cc: Shan.Palanisamy@Atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I accidentally transposed these in the patch that "fixed" the defaults,
leading to extremely low throughput because of the huge min CW.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have some validation code in mac80211 but said code will
force an invalid AID to 0 which isn't a valid AID either;
instead require a valid AID (1-2007) to be passed in from
userspace in cfg80211 already. Also move the code before
the race comment since it can only be executed during STA
addition and thus is not racy.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo has updated the driver to no longer use the change flag,
so we can remove that, but rt2x00 and ath5k still use the
actual value so let's mark it as deprecated too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ALIGN() and PTR_ALIGN() macros instead of handcoding them.
Get rid of NETDEV_ALIGN_CONST ugly define
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My first patch submission used 200ms, which I then somehow
managed to revert back to the earlier 50ms I had used for
some tests in the second patch submission -- but that was
wrong, I should have used 200ms here. Correct that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "mac80211: split out and decrease probe wait time" I tried
to reduce the time waiting for a probe response, but failed to
take into account the case where we are detecting beacon loss
in software -- in that case we still wait the monitoring time
rather than the probe wait time. Fix this by refactoring the
mod_timer() calls in ieee80211_associated().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, we will ask the driver to configure right away
when somebody changes the desired BSSID. That's totally
strange because then we will configure the driver without
even knowing whether the BSS exists. Change this to only
configure the BSSID when associated, and configure a zero
BSSID when not associated.
As a side effect, this fixes an issue with the iwlwifi
driver which doesn't implement sta_notify properly and
uses the BSSID instead and gets very confused if the
BSSID is cleared before we disassociate, which results
in the warning Marcel posted [1] and iwlwifi bug 1995 [2].
[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/32598
[2] http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1995
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I fixed the crypto bit I must have done the negative
test only -- it is quite clearly impossible to find _any_
IBSS to join with the parameters put the wrong way around.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the genIE hasn't changed there's no reason to kick
the state machine since it won't be able to do anything
new -- doing this decreases the useless work we do for
reassociating because if we do kick the state machine
it will try to find a usable BSS but there might not be
one because wpa_supplicant will only change the BSSID
a little later.
In a sense this is a workaround for userspace behaviour,
but on the other hand userspace cannot really keep track
of what the kernel currently has for genIE since any
process could have changed that while wpa_supplicant
wasn't looking.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When updating the duration field for TX frames, skip the update for
PS-Poll frames that use this field for other purposes (AID).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the AP includes our AID in the TIM IE, we need to process the
Beacon frame as far as PS is concerned (send PS-Poll or nullfunc data
with PM=0). The previous code skipped this in cases where the CRC
value did not change and it would not change if the AP continues
including our AID in the TIM..
There is no need to count the crc32 value for directed_tim with this
change, so we can remove that part. In order not to change the order
of operations (i.e., update WMM parameters prior to sending PS-Poll),
the CRC match is checked twice as only after the PS processing step,
the rest of the function is skipped if nothing changed in the Beacon.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving information from config_interface to bss_info_changed
removed struct ieee80211_if_conf which the documentation still
refers to, additionally there's one kernel-doc description too
much and one other missing, fix all this.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forgot to cancel all timers in mac80211 when suspending.
In particular we forgot to deal with some things that can
cause hardware reconfiguration -- while it is down.
While at it we go ahead and add a warning in ieee80211_sta_work()
if its run while the suspend->resume cycle is in effect. This
should not happen and if it does it would indicate there is
a bug lurking in either mac80211 or mac80211 drivers.
With this now wpa_supplicant doesn't blink when I go to suspend
and resume where as before there where issues with some timers
running during the suspend->resume cycle. This caused a lot of
incorrect assumptions and would at times bring back the device
in an incoherent, but mostly recoverable, state.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel switch code is currently in the spectrum
management file, where arguably it belongs. However,
it is for managed mode only and uses the structures
for that mode only so having it in a more generic
file can be confusing. Additionally, my next patch
gets simpler with the code here.
When/if we ever implement this for IBSS or mesh then
we will need to rework the structures it uses anyway
at which point we could move the code back.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Validate RSC (NL80211_ATTR_KEY_SEQ) length in nl80211/cfg80211 instead
of having to do this in all the drivers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While the probe request poll is expected to work, it looks like it
does not always result in getting a response. The exact reason for
this is unclear, but anyway, if we do receive a Beacon frame from our
AP, there is no need to disconnect based on the probereq poll. This
seems to help keep the connection bit more stable in cases where
beacon loss is occurring semi-frequently.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The STA may drop the very first frame if it happens to be a retried
frame. This is because we maintian the last received sequence number
per TID for QoS frames and it is initialized to zero through kzalloc
during sta_info_alloc and the sequence number of the very first date
frame received would be ZERO (as per IEEE 802.11-2007, 7.1.3.4.1).
If the frame dropped happens to be an EAP Request Identity(very first
frame from the AP), then wpa_supplicnat disconnects the STA and the
whole procedure starts again.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the cfg80211 specific stuff to new cfg80211 debugfs
entries. Non-mac80211 will also get these entries now. There were
only 4 which we take:
rts_threshold
fragmentation_threshold
short_retry_limit
long_retry_limit
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more consistent with our nl80211 naming convention
for HT40-/+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's this internal wifi_wme_noack_test variable that
we use to set the QoS control if set. For one, it is
unlikely that it is set. Secondly, if set it needs to
influence the IEEE80211_TX_CTL_NO_ACK TX control flag,
and finally we should also be able to set it at all, so
make it available in debugfs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 announces a rate set with no basic rates,
this fixes it to use 1/2 or 6/9 Mbit as basic rates by default.
Additionally, mac80211 will currently adopt the peer's entire
rate set, rather than just the basic rate set; fix that too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even when we find an IBSS with the SSID we're looking for, we
may not be able to connect to it because it has a key and we
don't, or vice versa. Avoid such situations by checking the
privacy capability bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time we wait for a probe response after probing an AP due to
beacon loss is currently the same as the monitoring interval, 2s.
This is far too long, APs should respond to probes within a
fraction of that time. To be able to adjust both values, add a
new constant IEEE80211_PROBE_WAIT, use it for checking the probe
response, and adjust it down to 200ms instead of 2 seconds.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver might keep reporting beacon loss until we
disassociate -- catch that and don't respond to any
subsequent events until the probe is either successful
or we disassociate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting a key with NL80211_CMD_NEW_KEY, we should allow the key
sequence number (RSC) to be set in order to allow replay protection to
work correctly for group keys. This patch documents this use for
nl80211 and adds the couple of missing pieces in nl80211/cfg80211 and
mac80211 to support this. In addition, WEXT SIOCSIWENCODEEXT compat
processing in cfg80211 is extended to handle the RSC (this was already
specified in WEXT, but just not implemented in cfg80211/mac80211).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new NL80211_ATTR_CONTROL_PORT flag for NL80211_CMD_ASSOCIATE to
allow user space to indicate that it will control the IEEE 802.1X port
in station mode. Previously, mac80211 was always marking the port
authorized in station mode. This was enough when drop_unencrypted flag
was set. However, drop_unencrypted can currently be controlled only
with WEXT and the current nl80211 design does not allow fully secure
configuration. Fix this by providing a mechanism for user space to
control the IEEE 802.1X port in station mode (i.e., do the same that
we are already doing in AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is currently not possible to modify station flags, but that
capability would be very useful. This patch introduces a new
nl80211 attribute that contains a set/mask for station flags,
and updates the internal API (and mac80211) to mirror that.
The new attribute is parsed before falling back to the old so
that userspace can specify both (if it can) to work on all
kernels.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move key handling wireless extension ioctls from mac80211 to cfg80211
so that all drivers that implement the cfg80211 operations get wext
compatibility.
Note that this drops the SIOCGIWENCODE ioctl support for getting
IW_ENCODE_RESTRICTED/IW_ENCODE_OPEN. This means that iwconfig will
no longer report "Security mode:open" or "Security mode:restricted"
for mac80211. However, what we displayed there (the authentication
algo used) was actually wrong -- linux/wireless.h states that this
setting is meant to differentiate between "Refuse non-encoded packets"
and "Accept non-encoded packets".
(Combined with "cfg80211: fix a couple of bugs with key ioctls". -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The address pointed to by mac_addr can be marked as const.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we disassociate, we set the channel to non-HT which
obviously invalidates any ht_operation_mode setting. But
when we then associate with the next AP again, we might
still have the ht_operation_mode from the previous AP
cached and fail to configure the hardware with the new
(but unchanged) operation mode. This patch fixes it by
separately tracking whether our cache is valid.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There really is no need to have a separate struct for a
single variable. The fact that it exists is due to the
code legacy, but we can remove that now. Very simple.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The call to ieee80211_hw_config() is supposed to apply changes
synchronously, so once it returns the parameters are applied to
the hardware. Thus, there really is no need to delay the probing
by the channel switch time again since the channel switch has
already happened once we get to this code.
Additionally, there is no need to wait for a NAV update (probe
delay) when the channel is passively scanned. Remove that extra
time too.
This cuts scanning time from over 7 seconds to under 4 on ar9170,
which is due to the number of channels scanned and ar9170's switch
time being advertised as 135ms (my test now indicates it is about
77ms with the current driver, but the difference might also be due
to using a different machine with different USB controllers).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When management frame protection (IEEE 802.11w) is used, unprotected
Robust Action frames are not allowed prior to key configuration.
However, unprotected Deauthentication and Disassociation frames are
allowed at that point, but not after key configuration.
Make ieee80211_drop_unencrypted() handle the special cases for MFP by
separating the basic Data frame case from Management frame processing
and handle the Management frames only if MFP has been negotiated. In
addition, do not use sdata->drop_unencrypted for Management frames
since the decision on whether to accept the frame depends on the key
being configured.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using nl80211, we do not have a mechanism to set
sdata->drop_unencrypted. Currently, this breaks code that is supposed
to drop unencrypted frames when protection is expected since
ieee80211_rx_h_decrypt() is optimized to not set rx->key when the
frame is not protected.
This patch modifies ieee80211_rx_h_decrypt() to set rx->key for all
frames and only skip decryption if the frame is not protected. This
allows ieee80211_drop_unencrypted() to correctly drop frames even if
drop_unencrypted is not set.
The changes here are not enough to handle all cases, though. Additional
patches will be needed to implement proper IEEE 802.1X PAE for station
mode (currently, this is only used for AP mode) and some additional
rules are needed for MFP to drop unprotected Robust Action frames prior
to having PTK and IGTK configured.
In theory, the unprotected frames could and should be dropped in
ieee80211_rx_h_decrypt(). However, due to the special case with EAPOL
frames that have to be allowed to be received unprotected even when
keys are set, it is simpler to only set rx->key and allow the
ieee80211_frame_allowed() function to handle the actual dropping of
data frames after 802.11->802.3 header conversion. In addition,
unprotected robust management frames are dropped before they are
processed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've never really cared about the default QoS (WMM) values, but
we really should if the AP doesn't send any. This patch makes
mac80211 use the default values according to 802.11-2007, and
additionally syncs the default values when we disassociate so
whatever the last AP said gets "unconfigured".
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
