Keep chip_data in create_irq_nr and destroy_irq.
When two drivers are setting up MSI-X at the same time via
pci_enable_msix() there is a race. See this dmesg excerpt:
[ 85.170610] ixgbe 0000:02:00.1: irq 97 for MSI/MSI-X
[ 85.170611] alloc irq_desc for 99 on node -1
[ 85.170613] igb 0000:08:00.1: irq 98 for MSI/MSI-X
[ 85.170614] alloc kstat_irqs on node -1
[ 85.170616] alloc irq_2_iommu on node -1
[ 85.170617] alloc irq_desc for 100 on node -1
[ 85.170619] alloc kstat_irqs on node -1
[ 85.170621] alloc irq_2_iommu on node -1
[ 85.170625] ixgbe 0000:02:00.1: irq 99 for MSI/MSI-X
[ 85.170626] alloc irq_desc for 101 on node -1
[ 85.170628] igb 0000:08:00.1: irq 100 for MSI/MSI-X
[ 85.170630] alloc kstat_irqs on node -1
[ 85.170631] alloc irq_2_iommu on node -1
[ 85.170635] alloc irq_desc for 102 on node -1
[ 85.170636] alloc kstat_irqs on node -1
[ 85.170639] alloc irq_2_iommu on node -1
[ 85.170646] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000088
As you can see igb and ixgbe are both alternating on create_irq_nr()
via pci_enable_msix() in their probe function.
ixgbe: While looping through irq_desc_ptrs[] via create_irq_nr() ixgbe
choses irq_desc_ptrs[102] and exits the loop, drops vector_lock and
calls dynamic_irq_init. Then it sets irq_desc_ptrs[102]->chip_data =
NULL via dynamic_irq_init().
igb: Grabs the vector_lock now and starts looping over irq_desc_ptrs[]
via create_irq_nr(). It gets to irq_desc_ptrs[102] and does this:
cfg_new = irq_desc_ptrs[102]->chip_data;
if (cfg_new->vector != 0)
continue;
This hits the NULL deref.
Another possible race exists via pci_disable_msix() in a driver or in
the number of error paths that call free_msi_irqs():
destroy_irq()
dynamic_irq_cleanup() which sets desc->chip_data = NULL
...race window...
desc->chip_data = cfg;
Remove the save and restore code for cfg in create_irq_nr() and
destroy_irq() and take the desc->lock when checking the irq_cfg.
Reported-and-analyzed-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-3-git-send-email-yinghai@kernel.org>
Signed-off-by: Brandon Phililps <bphilips@suse.de>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Thomas Renninger <trenn@suse.de> reported on IBM x3330
booting a latest kernel on this machine results in:
PCI: PCI BIOS revision 2.10 entry at 0xfd61c, last bus=1
PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0
ACPI: SCI (IRQ30) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20090903/evevent-161)
ACPI: Unable to start the ACPI Interpreter
Later all kind of devices fail...
and bisect it down to this commit:
commit b9c61b7007
x86/pci: update pirq_enable_irq() to setup io apic routing
it turns out we need to set irq routing for the sci on ioapic1 early.
-v2: make it work without sparseirq too.
-v3: fix checkpatch.pl warning, and cc to stable
Reported-by: Thomas Renninger <trenn@suse.de>
Bisected-by: Thomas Renninger <trenn@suse.de>
Tested-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-2-git-send-email-yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Avi Kivity <avi@redhat.com>
Cc: x86@kernel.org
LKML-Reference: <1265478443-31072-10-git-send-email-elendil@planet.nl>
[ Left out the KVM bits. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Lowest priority delivery of logical flat mode is broken on some systems,
such that even when IO-APIC RTE says deliver the interrupt to a particular CPU,
interrupt subsystem delivers the interrupt to totally different CPU.
For example, this behavior was observed on a P4 based system with SiS chipset
which was reported by Li Zefan. We have been handling this kind of behavior by
making sure that in logical flat mode, we assign the same vector to irq
mappings on all the 8 possible logical cpu's.
But we have been doing this initial assignment (__setup_vector_irq()) a little
late (before which interrupts were already enabled for a short duration).
Move the __setup_vector_irq() before the first irq enable point in the
cpu online path to avoid the issue of not handling some interrupts that
wrongly hit the cpu which is still coming online.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100129194330.283696385@sbs-t61.sc.intel.com>
Tested-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
In the recent change of not reserving IRQ0_VECTOR..IRQ15_VECTOR's on all
cpu's, we start with irq 0..15 getting directed to (and handled on) cpu-0.
In the logical flat mode, once the AP's are online (and before irqbalance
comes into picture), kernel intends to handle these IRQ's on any cpu (as the
logical flat mode allows to specify multiple cpu's for the irq destination and
the chipset based routing can deliver to the interrupt to any one of
the specified cpu's). This was broken with our recent change, which was ending
up using only cpu 0 as the destination, even when the kernel was specifying to
use all online cpu's for the logical flat mode case.
Fix this by updating vector allocation domain (cfg->domain) for legacy irqs,
when the IO-APIC handles them.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100129194330.207790269@sbs-t61.sc.intel.com>
Tested-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Currently IRQ0..IRQ15 are assigned to IRQ0_VECTOR..IRQ15_VECTOR's on
all the cpu's.
If these IRQ's are handled by legacy pic controller, then the kernel
handles them only on cpu 0. So there is no need to block this vector
space on all cpu's.
Similarly if these IRQ's are handled by IO-APIC, then the IRQ affinity
will determine on which cpu's we need allocate the vector resource for
that particular IRQ. This can be done dynamically and here also there
is no need to block 16 vectors for IRQ0..IRQ15 on all cpu's.
Fix this by initially assigning IRQ0..IRQ15 to IRQ0_VECTOR..IRQ15_VECTOR's only
on cpu 0. If the legacy controllers like pic handles these irq's, then
this configuration will be fixed. If more modern controllers like IO-APIC
handle these IRQ's, then we start with this configuration and as IRQ's
migrate, vectors (/and cpu's) associated with these IRQ's change dynamically.
This will freeup the block of 16 vectors on other cpu's which don't handle
IRQ0..IRQ15, which can now be used for other IRQ's that the particular cpu
handle.
[ hpa: this also an architectural cleanup for future legacy-PIC-free
configurations. ]
[ hpa: fixed typo NR_LEGACY_IRQS -> NR_IRQS_LEGACY ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1263932453.2814.52.camel@sbs-t61.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
After talking to some more folks inside intel (Peter Anvin, Asit Mallick),
the safest option (for future compatibility etc) seen was to use vector 0x20
for IRQ_MOVE_CLEANUP_VECTOR instead of using vector 0x1f (which is documented as
reserved vector in the Intel IA32 manuals).
Also we don't need to reserve the entire privilege level (all 16 vectors in
the priority bucket that IRQ_MOVE_CLEANUP_VECTOR falls into), as the
x86 architecture (section 10.9.3 in SDM Vol3a) specifies that with in the
priority level, the higher the vector number the higher the priority.
And hence we don't need to reserve the complete priority level 0x20-0x2f for
the IRQ migration cleanup logic.
So change the IRQ_MOVE_CLEANUP_VECTOR to 0x20 and allow 0x21-0x2f to be used
for device interrupts. 0x30-0x3f will be used for ISA interrupts (these
also can be migrated in the context of IOAPIC and hence need to be at a higher
priority level than IRQ_MOVE_CLEANUP_VECTOR).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100114002118.521826763@sbs-t61.sc.intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
With the recent irq migration fixes (post 2.6.32), Gary Hade has noticed
"No IRQ handler for vector" messages during the 2.6.33-rc1 kernel boot on IBM
AMD platforms and root caused the issue to this commit:
> commit 23359a88e7
> Author: Suresh Siddha <suresh.b.siddha@intel.com>
> Date: Mon Oct 26 14:24:33 2009 -0800
>
> x86: Remove move_cleanup_count from irq_cfg
As part of this patch, we have removed the move_cleanup_count check
in smp_irq_move_cleanup_interrupt(). With this change, we can run into a
situation where an irq cleanup interrupt on a cpu can cleanup the vector
mappings associated with multiple irqs, of which one of the irq's migration
might be still in progress. As such when that irq hits the old cpu, we get
the "No IRQ handler" messages.
Fix this by checking for the irq_cfg's move_in_progress and if the move
is still in progress delay the vector cleanup to another irq cleanup
interrupt request (which will happen when the irq starts arriving at the
new cpu destination).
Reported-and-tested-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1262804191.2732.7.camel@sbs-t61.sc.intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We want to use a vector-assignment sequence that avoids stumbling onto
0x80 earlier in the sequence, in order to improve the spread of
vectors across priority levels on machines with a small number of
interrupt sources. Right now, this is done by simply making the first
vector (0x31 or 0x41) completely unusable. This is unnecessary; all
we need is to start assignment at a +1 offset, we don't actually need
to prohibit the usage of this vector once we have wrapped around.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <4B426550.6000209@kernel.org>
I have a system with lots of igb and ixgbe, when iov/vf are
enabled for them, we hit the limit of 3064.
when system has 20 pcie installed, and one card has 2
functions, and one function needs 64 msi-x,
may need 20 * 2 * 64 = 2560 for msi-x
but if iov and vf are enabled
may need 20 * 2 * 64 * 3 = 7680 for msi-x
assume system with 5 ioapic, nr_irqs_gsi will be 120.
NR_CPUS = 512, and nr_cpu_ids = 128
will have NR_IRQS = 256 + 512 * 64 = 33024
will have nr_irqs = 120 + 8 * 128 + 120 * 64 = 8824
When SPARSE_IRQ is not set, there is no increase with kernel data
size.
when NR_CPUS=128, and SPARSE_IRQ is set:
text data bss dec hex filename
21837444 4216564 12480736 38534744 24bfe58 vmlinux.before
21837442 4216580 12480736 38534758 24bfe66 vmlinux.after
when NR_CPUS=4096, and SPARSE_IRQ is set
text data bss dec hex filename
21878619 5610244 13415392 40904255 270263f vmlinux.before
21878617 5610244 13415392 40904253 270263d vmlinux.after
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4B398ECD.1080506@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, irq: Allow 0xff for /proc/irq/[n]/smp_affinity on an 8-cpu system
Makefile: Unexport LC_ALL instead of clearing it
x86: Fix objdump version check in arch/x86/tools/chkobjdump.awk
x86: Reenable TSC sync check at boot, even with NONSTOP_TSC
x86: Don't use POSIX character classes in gen-insn-attr-x86.awk
Makefile: set LC_CTYPE, LC_COLLATE, LC_NUMERIC to C
x86: Increase MAX_EARLY_RES; insufficient on 32-bit NUMA
x86: Fix checking of SRAT when node 0 ram is not from 0
x86, cpuid: Add "volatile" to asm in native_cpuid()
x86, msr: msrs_alloc/free for CONFIG_SMP=n
x86, amd: Get multi-node CPU info from NodeId MSR instead of PCI config space
x86: Add IA32_TSC_AUX MSR and use it
x86, msr/cpuid: Register enough minors for the MSR and CPUID drivers
initramfs: add missing decompressor error check
bzip2: Add missing checks for malloc returning NULL
bzip2/lzma/gzip: pre-boot malloc doesn't return NULL on failure
John Blackwood reported:
> on an older Dell PowerEdge 6650 system with 8 cpus (4 are hyper-threaded),
> and 32 bit (x86) kernel, once you change the irq smp_affinity of an irq
> to be less than all cpus in the system, you can never change really the
> irq smp_affinity back to be all cpus in the system (0xff) again,
> even though no error status is returned on the "/bin/echo ff >
> /proc/irq/[n]/smp_affinity" operation.
>
> This is due to that fact that BAD_APICID has the same value as
> all cpus (0xff) on 32bit kernels, and thus the value returned from
> set_desc_affinity() via the cpu_mask_to_apicid_and() function is treated
> as a failure in set_ioapic_affinity_irq_desc(), and no affinity changes
> are made.
set_desc_affinity() is already checking if the incoming cpu mask
intersects with the cpu online mask or not. So there is no need
for the apic op cpu_mask_to_apicid_and() to check again
and return BAD_APICID.
Remove the BAD_APICID return value from cpu_mask_to_apicid_and()
and also fix set_desc_affinity() to return -1 instead of using BAD_APICID
to represent error conditions (as cpu_mask_to_apicid_and() can return
logical or physical apicid values and BAD_APICID is really to represent
bad physical apic id).
Reported-by: John Blackwood <john.blackwood@ccur.com>
Root-caused-by: John Blackwood <john.blackwood@ccur.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1261103386.2535.409.camel@sbs-t61>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
* 'timers-for-linus-hpet' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Make WARN_ON understandable
x86: arch specific support for remapping HPET MSIs
intr-remap: generic support for remapping HPET MSIs
x86, hpet: Simplify the HPET code
x86, hpet: Disable per-cpu hpet timer if ARAT is supported
In the case when cpu goes offline, fixup_irqs() will forward any
unhandled interrupt on the offlined cpu to the new cpu
destination that is handling the corresponding interrupt. This
interrupt forwarding is done via IPI's. Hence, in this case also
level-triggered io-apic interrupt will be seen as an edge
interrupt in the cpu's APIC IRR.
Document this scenario in the code which handles this case by doing
an explicit EOI to the io-apic to clear remote IRR of the io-apic RTE.
Requested-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: ebiederm@xmission.com
Cc: garyhade@us.ibm.com
LKML-Reference: <20091201233335.143970505@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Maciej W. Rozycki reported:
> 82093AA I/O APIC has its version set to 0x11 and it
> does not support the EOI register. Similarly I/O APICs
> integrated into the 82379AB south bridge and the 82374EB/SB
> EISA component.
IO-APIC versions below 0x20 don't support EOI register.
Some of the Intel ICH Specs (ICH2 to ICH5) documents the io-apic
version as 0x2. This is an error with documentation and these
ICH chips use io-apic's of version 0x20 and indeed has a working
EOI register for the io-apic.
Fix the EOI register detection mechanism to check for version
0x20 and beyond.
And also, a platform can potentially have io-apic's with
different versions. Make the EOI register check per io-apic.
Reported-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: ebiederm@xmission.com
Cc: garyhade@us.ibm.com
LKML-Reference: <20091201233335.065361533@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When the level-triggered interrupt is seen as an edge interrupt,
we try to clear the remoteIRR explicitly (using either an
io-apic eoi register when present or through the idea of
changing trigger mode of the io-apic RTE to edge and then back
to level). But this explicit try also needs to happen before we
try to migrate the irq. Otherwise irq migration attempt will
fail anyhow, as it postpones the irq migration to a later
attempt when it sees the remoteIRR in the io-apic RTE still set.
Signed-off-by: "Maciej W. Rozycki" <macro@linux-mips.org>
Reviewed-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: ebiederm@xmission.com
Cc: garyhade@us.ibm.com
LKML-Reference: <20091201233334.975416130@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When irq_desc is moved, we need to make sure to use the right cfg_new.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B07A739.3030104@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If IO-APIC base address is 1K aligned we should not fail
on resourse insertion procedure. For this sake we define
IO_APIC_SLOT_SIZE constant which should cover all IO-APIC
direct accessible registers.
An example of a such configuration is there
http://marc.info/?l=linux-kernel&m=118114792006520
|
| Quoting the message
|
| IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
| IOAPIC[1]: apic_id 3, version 32, address 0xfec80000, GSI 24-47
| IOAPIC[2]: apic_id 4, version 32, address 0xfec80400, GSI 48-71
| IOAPIC[3]: apic_id 5, version 32, address 0xfec84000, GSI 72-95
| IOAPIC[4]: apic_id 8, version 32, address 0xfec84400, GSI 96-119
|
Reported-by: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20091116151426.GC5653@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We should not use physid_mask_t as a stack based
variable in apic code. This type depends on MAX_APICS
parameter which may be huge enough.
Especially it became a problem with apic NOOP driver which
is portable between 32 bit and 64 bit environment
(where we have really huge MAX_APICS).
So apic driver should operate with pointers and a caller
in turn should aware of allocation physid_mask_t variable.
As a side (but positive) effect -- we may use already
implemented physid_set_mask_of_physid function eliminating
default_apicid_to_cpu_present completely.
Note that physids_coerce and physids_promote turned into static
inline from macro (since macro hides the fact that parameter is
being interpreted as unsigned long, make it explicit).
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20091109220659.GA5568@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We should be ready that one day MAX_IO_APICS may raise its
number. To prevent memory overwrite we're to use safe
snprintf while set IO-APIC resourse name.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20091108155431.GC25940@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The whole page is reserved for IO-APIC fixmap
due to non-cacheable requirement. So lets note
this explicitly instead of playing with numbers.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
LKML-Reference: <20091108155356.GB25940@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IO-APIC's in intel chipsets support EOI register starting from
IO-APIC version 2. Use that when ever we need to clear the
IO-APIC RTE's RemoteIRR bit explicitly.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.947855317@sbs-t61.sc.intel.com>
[ Marked use_eio_reg as __read_mostly, fixed small details ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When a cpu goes offline, fixup_irqs() try to move irq's
currently destined to the offline cpu to a new cpu. But this
attempt will fail if the irq is recently moved to this cpu and
the irq still hasn't arrived at this cpu (for non intr-remapping
platforms this is when we free the vector allocation at the
previous destination) that is about to go offline.
This will endup with the interrupt subsystem still pointing the
irq to the offline cpu, causing that irq to not work any more.
Fix this by forcing the irq to complete its move (its been a
long time we moved the irq to this cpu which we are offlining
now) and then move this irq to a new cpu before this cpu goes
offline.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.848830905@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move_cleanup_count for each irq in irq_cfg is keeping track of
the total number of cpus that need to free the corresponding
vectors associated with the irq which has now been migrated to
new destination. As long as this move_cleanup_count is non-zero
(i.e., as long as we have n't freed the vector allocations on
the old destinations) we were preventing the irq's further
migration.
This cleanup count is unnecessary and it is enough to not allow
the irq migration till we send the cleanup vector to the
previous irq destination, for which we already have irq_cfg's
move_in_progress. All we need to make sure is that we free the
vector at the old desintation but we don't need to wait till
that gets freed.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.752968906@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move UV specific functionality out of the generic IO-APIC code.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
LKML-Reference: <20091013203236.GD20543@sgi.com>
[ Cleaned up the code some more in their new places. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes handling of uv hub irq affinity. IRQs with ALL or
NODE affinity can be routed to cpus other than their originally
assigned cpu. Those with CPU affinity cannot be rerouted.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
LKML-Reference: <20090930160259.GA7822@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case if a system has a large number of cpus printing apics
contents may consume a long time period.
We limit such an output by 1 apic by default. But to have an
ability to see all apics or some part of them we introduce
"show_lapic" setup option which allow us to limit/unlimit the
number of APICs being dumped.
Example: apic=debug show_lapic=5, or apic=debug show_lapic=all
Also move apic_verbosity checking upper that way so helper routines
do not need to inspect it at all.
Suggested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: yinghai@kernel.org
Cc: macro@linux-mips.org
LKML-Reference: <20091013201022.926793122@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove open-coded zalloc_cpumask_var() and zalloc_cpumask_var_node().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In case of discrete (pretty old) apics we may have cpu_has_apic bit
not set but have to check if smp_found_config (MP spec) is there
and apic was not disabled.
Also don't forget to print apic/io-apic for such case as well.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090915071230.GA10604@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (38 commits)
x86: Move get/set_wallclock to x86_platform_ops
x86: platform: Fix section annotations
x86: apic namespace cleanup
x86: Distangle ioapic and i8259
x86: Add Moorestown early detection
x86: Add hardware_subarch ID for Moorestown
x86: Add early platform detection
x86: Move tsc_init to late_time_init
x86: Move tsc_calibration to x86_init_ops
x86: Replace the now identical time_32/64.c by time.c
x86: time_32/64.c unify profile_pc
x86: Move calibrate_cpu to tsc.c
x86: Make timer setup and global variables the same in time_32/64.c
x86: Remove mca bus ifdef from timer interrupt
x86: Simplify timer_ack magic in time_32.c
x86: Prepare unification of time_32/64.c
x86: Remove do_timer hook
x86: Add timer_init to x86_init_ops
x86: Move percpu clockevents setup to x86_init_ops
x86: Move xen_post_allocator_init into xen_pagetable_setup_done
...
Fix up conflicts in arch/x86/include/asm/io_apic.h
The proposed Moorestown support patches use an extra feature flag
mechanism to make the ioapic work w/o an i8259. There is a much
simpler solution.
Most i8259 specific functions are already called dependend on the irq
number less than NR_IRQS_LEGACY. Replacing that constant by a
read_mostly variable which can be set to 0 by the platform setup code
allows us to achieve the same without any special feature flags.
That trivial change allows us to proceed with MRST w/o doing a full
blown overhaul of the ioapic code which would delay MRST unduly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge reason: the SFI (Simple Firmware Interface) feature in the ACPI
tree needs this cleanup, pull it into the APIC branch as
well so that there's no interactions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some IO-APIC routines are ACPI specific now, but need to
be exposed when CONFIG_ACPI=n for the benefit of SFI.
Remove #ifdef ACPI around these routines:
io_apic_get_unique_id(int ioapic, int apic_id);
io_apic_get_version(int ioapic);
io_apic_get_redir_entries(int ioapic);
Move these routines from ACPI-specific boot.c to io_apic.c:
uniq_ioapic_id(u8 id)
mp_find_ioapic()
mp_find_ioapic_pin()
mp_register_ioapic()
Also, since uniq_ioapic_id() is now no longer static,
re-name it to io_apic_unique_id() for consistency
with the other public io_apic routines.
For simplicity, do not #ifdef the resulting code ACPI || SFI,
thought that could be done in the future if it is important
to optimize the !ACPI !SFI IO-APIC x86 kernel for size.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
x86 arch support for remapping HPET MSI's by associating the HPET timer block
with the interrupt-remapping HW unit and setting up appropriate irq_chip
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jay Fenlason <fenlason@redhat.com>
LKML-Reference: <20090804190729.630510000@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
32bit and also the numaq code have special requirements on the
ioapic_id setup. Convert it to a x86_init_ops function and get rid
of the quirks and #ifdefs
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
alloc_bootmem() already panics on allocation failure. There is
no need to check the result.
Also there is a way to unbind global variable from its body and
use it as a parameter which allow us to simplify
ioapic_init_mappings as well -- "for" cycle already uses
nr_ioapics as a conditional variable and there is no need to
check if ioapic_setup_resources was returning NULL again.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090824175551.493629148@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Though the most time we are to panic on irq-pin allocation
fails, for PCI interrupts it's not the case and we could
continue operate even if irq-pin allocation failed.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090805200931.GB5319@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Instead of plain NULL deref we better throw error
message with a backtrace. Actually we need more
gracious error handling here. Meanwhile leave it
as is.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: yinghai@kernel.org
LKML-Reference: <20090801075435.769301745@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This allow us to save a few lines of code.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: yinghai@kernel.org
LKML-Reference: <20090801075435.597863129@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In uv_setup_irq(), the call to create_irq() initially assigns
IRQ vectors to cpu 0. The subsequent call to
assign_irq_vector() in arch_enable_uv_irq() migrates the IRQ to
another cpu and frees the cpu 0 vector - at least it will be
freed as soon as the "IRQ move" completes.
arch_enable_uv_irq() needs to send a cleanup IPI to complete
the IRQ move. Otherwise, assignment of GRU interrupts on large
systems (>200 cpus) will exhaust the cpu 0 interrupt vectors
and initialization of the GRU driver will fail.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090720142840.GA8885@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This takes care of the following entry from Dan's list:
arch/x86/kernel/apic/io_apic.c +3241 destroy_irq(11) warning: variable derefenced before check 'desc'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eugene Teo <eteo@redhat.com>
Cc: Julia Lawall <julia@diku.dk>
LKML-Reference: <200907302321.19086.bzolnier@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The 32 and 64-bit versions of ioapic_retrigger_irq() are identical
except the 64-bit one takes vector_lock. vector_lock is defined and
used on 32-bit too, so just use a common ioapic_retrigger_irq().
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
There's no need for a control variable in replace_pin_at_irq_node();
it can just return if it finds the old apic/pin to replace.
If the loop terminates, then it didn't find the old apic/pin, so it can
add the new ones.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Rather than duplicating the same alloc/init code twice, restructure
the function to look for duplicates and then add an entry
if none is found.
This function is not performance critical; all but one of its callers
are __init functions, and the non-__init caller is for PCI device setup.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Convert the unconventional loop in io_apic_level_ack_pending() to
a conventional for() loop.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The comment got separated from its subject, so move it to what
appears to be the right place, and update to describe the current
structure.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The structure is defined immediately below, so there's no need
to forward declare it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
While no 64-bit hardware will have a version 0x11 I/O APIC which needs
the level/edge bug workaround, that's not a particular reason to use
CONFIG_X86_32 to #ifdef the code out. Most 32-bit machines will no
longer need the workaround either, so the test to see whether it is
necessary should be more fine-grained than "32-bit=yes, 64-bit=no".
(Also fix formatting of block comment.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The main difference between 32 and 64-bit __mask_IO_APIC_irq() does a
readback from the I/O APIC to synchronize it.
If there's a hardware requirement to do a readback sync after updating
an APIC register, then it will be a hardware requrement regardless of
whether the kernel is compiled 32 or 64-bit.
Unify __mask_IO_APIC_irq() using the 64-bit version which always syncs
with io_apic_sync().
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If ioapic_modify_irq() is marked inline, it gets inlined several times.
Un-inlining it saves around 200 bytes in .text for me.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Stephen reported that his DL585 G2 needed noapic after 2.6.22 (?)
Dann bisected it down to:
commit 30a18d6c3f
Date: Tue Feb 19 03:21:20 2008 -0800
x86: multi pci root bus with different io resource range, on
64-bit
It turns out that:
1. that AMD-based systems have two HT chains.
2. BIOS doesn't allocate resources for BAR 6 of devices under 8132 etc
3. that multi-peer-root patch will try to split root resources to peer
root resources according to PCI conf of NB
4. PCI core assigns unassigned resources, but they overlap with BARs
that are used by ioapic addr of io4 and 8132.
The reason: at that point ioapic address are not inserted yet. Solution
is to insert ioapic resources into the tree a bit earlier.
Reported-by: Stephen Frost <sfrost@snowman.net>
Reported-and-Tested-by: dann frazier <dannf@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@jbarnes-g45.(none)>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To support domain-isolation usages, the platform hardware must be
capable of uniquely identifying the requestor (source-id) for each
interrupt message. Without source-id checking for interrupt remapping
, a rouge guest/VM with assigned devices can launch interrupt attacks
to bring down anothe guest/VM or the VMM itself.
This patch adds source-id checking for interrupt remapping, and then
really isolates interrupts for guests/VMs with assigned devices.
Because PCI subsystem is not initialized yet when set up IOAPIC
entries, use read_pci_config_byte to access PCI config space directly.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This compiler warning:
arch/x86/kernel/apic/io_apic.c: In function ‘ioapic_write_entry’:
arch/x86/kernel/apic/io_apic.c:466: warning: ‘eu’ is used uninitialized in this function
arch/x86/kernel/apic/io_apic.c:465: note: ‘eu’ was declared here
Is bogus as 'eu' is always initialized. But annotate it away by
initializing the variable, to make it easier for people to notice
real warnings. A compiler that sees through this logic will
optimize away the initialization.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
LKML-Reference: <1245248720.3312.27.camel@myhost>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So we make sure MAXSMP gets a cleared cpumask
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't hardcode to node zero for early boot IRQ setup memory allocations.
[ penberg@cs.helsinki.fi: minor cleanups ]
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Now that we set up the slab allocator earlier, we can get rid of some
alloc_bootmem_cpumask_var() calls in boot code.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, nmi: Use predefined numbers instead of hardcoded one
x86: asm/processor.h: remove double declaration
x86, mtrr: replace MTRRdefType_MSR with msr-index's MSR_MTRRdefType
x86, mtrr: replace MTRRfix4K_C0000_MSR with msr-index's MSR_MTRRfix4K_C0000
x86, mtrr: remove mtrr MSRs double declaration
x86, mtrr: replace MTRRfix16K_80000_MSR with msr-index's MSR_MTRRfix16K_80000
x86, mtrr: replace MTRRfix64K_00000_MSR with msr-index's MSR_MTRRfix64K_00000
x86, mtrr: replace MTRRcap_MSR with msr-index's MSR_MTRRcap
x86: mce: remove duplicated #include
x86: msr-index.h remove duplicate MSR C001_0015 declaration
x86: clean up arch/x86/kernel/tsc_sync.c a bit
x86: use symbolic name for VM86_SIGNAL when used as vm86 default return
x86: added 'ifndef _ASM_X86_IOMAP_H' to iomap.h
x86: avoid multiple declaration of kstack_depth_to_print
x86: vdso/vma.c declare vdso_enabled and arch_setup_additional_pages before they get used
x86: clean up declarations and variables
x86: apic/x2apic_cluster.c x86_cpu_to_logical_apicid should be static
x86 early quirks: eliminate unused function
Fix the fact that the IOAPIC version number in the x86_64 code path always
gets assigned to 0, instead of the correct value.
Before the patch: (from "dmesg" output):
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23 <---
After the patch:
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 <---
History:
io_apic_get_version() was compiled out of the x86_64 code path in the commit
f2c2cca3ac:
Author: Andi Kleen <ak@suse.de>
Date: Tue Sep 26 10:52:37 2006 +0200
[PATCH] Remove APIC version/cpu capability mpparse checking/printing
ACPI went to great trouble to get the APIC version and CPU capabilities
of different CPUs before passing them to the mpparser. But all
that data was used was to print it out. Actually it even faked some data
based on the boot cpu, not on the actual CPU being booted.
Remove all this code because it's not needed.
Cc: len.brown@intel.com
At the time, the IOAPIC version number was deliberately not printed
in the x86_64 code path. However, after the x86 and x86_64 files were
merged, the net result is that the IOAPIC version is printed incorrectly
in the x86_64 code path.
The patch below provides a fix. I have tested it with acpi, and with
acpi=off, and did not see any problems.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
LKML-Reference: <20090416014230.4885.94926.sendpatchset@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
*************************
Peter bisected that:
| commit b9c61b7007
| Date: Wed May 6 10:10:06 2009 -0700
|
| x86/pci: update pirq_enable_irq() to setup io apic routing
|
| So we can set io apic routing only when enabling the device irq.
wrecked his opteron box, ata1 interrupts fail to get through.
ata1 is using irq 11:
[ 1.451839] sata_svw 0000:01:0e.0: version 2.3
[ 1.456333] sata_svw 0000:01:0e.0: PCI INT A -> GSI 11 (level, low) -> IRQ 11
[ 1.463639] scsi0 : sata_svw
[ 1.466949] scsi1 : sata_svw
[ 1.470022] scsi2 : sata_svw
[ 1.473090] scsi3 : sata_svw
[ 1.476112] ata1: SATA max UDMA/133 mmio m8192@0xff3fe000 port 0xff3fe000 irq 11
[ 1.483490] ata2: SATA max UDMA/133 mmio m8192@0xff3fe000 port 0xff3fe100 irq 11
[ 1.490870] ata3: SATA max UDMA/133 mmio m8192@0xff3fe000 port 0xff3fe200 irq 11
[ 1.498247] ata4: SATA max UDMA/133 mmio m8192@0xff3fe000 port 0xff3fe300 irq 11
that pin is overlapped with pin with legacy ones.
We should not set bits in pin_programmed here, so that those bit could
be set later via io_apic_set_pci_routing().
[ Impact: fix boot hang on certain systems ]
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Yinghai Lu <yinghai.lu@kernel.org>
Tested-by: Peter Zijlstra <peterz@infradead.org>
Cc: Jack Steiner <steiner@sgi.com>
LKML-Reference: <4A119990.9020606@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
according to Ingo, io_apic irq-setup related functions have too many
parameters with a repetitive signature.
So reduce related funcs to get less params by passing a pointer
to a newly defined io_apic_irq_attr structure.
v2: io_apic_irq ==> irq_attr
triggering ==> trigger
v3: add set_io_apic_irq_attr
[ Impact: cleanup ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A08ACD3.2070401@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ed found that on 32-bit, boot_cpu_physical_apicid is not read right,
when the mptable is broken.
Interestingly, actually three paths use/set it:
1. acpi: at that time that is already read from reg
2. mptable: only read from mptable
3. no madt, and no mptable, that use default apic id 0 for 64-bit, -1 for 32-bit
so we could read the apic id for the 2/3 path. We trust the hardware
register more than we trust a BIOS data structure (the mptable).
We can also avoid the double set_fixmap() when acpi_lapic
is used, and also need to move cpu_has_apic earlier and
call apic_disable().
Also when need to update the apic id, we'd better read and
set the apic version as well - so that quirks are applied precisely.
v2: make path 3 with 64bit, use -1 as apic id, so could read it later.
v3: fix whitespace problem pointed out by Ed Swierk
v5: fix boot crash
[ Impact: get correct apic id for bsp other than acpi path ]
Reported-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <49FC85A9.2070702@kernel.org>
[ v4: sanity-check in the ACPI case too ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: both topics modify the APIC code but were able to do it in
parallel so far. An upcoming patch generates a conflict so
merge them to avoid the conflict.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Both print_local_APIC (used when apic=debug kernel param is set) and
cpu_debug code missed support for some extended APIC registers that
I'd like to see.
This adds support to show:
- extended APIC feature register
- extended APIC control register
- extended LVT registers
[ Impact: print more debug info ]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <20090508162350.GO29045@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So we can set io apic routing only when enabling the device irq.
This is advantageous for IRQ descriptor allocation affinity: if we set up
the IO-APIC entry later, we have a chance to allocate the IRQ descriptor
later and know which device it is on and can set affinity accordingly.
[ Impact: standardize/enhance irq-enabling sequence for mptable irqs ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A01C46E.8000501@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So we could set io apic routing when ACPI is not enabled.
[ Impact: prepare for new functionality ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A01C422.5070400@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To prepare those params for pcibios_irq_enable() to call setup_io_apic_routing().
[ Impact: extend function call API to prepare for new functionality ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A01C406.2040303@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Prepare to call setup_io_apic_routing() in pcibios_irq_enable()
also remove not needed member apic_id.
[ Impact: clean up, prepare for future change ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A01C3DD.3050104@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The expression is known to be true/false at compilation
time so we're allowed to use build-time instead of
run-time check. Also align 'entry' items assignment.
[ Impact: shrink kernel a bit, cleanup ]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090502093956.GB4791@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
arch/x86/kernel/apic/io_apic.c
Merge reason: non-trivial interaction between ongoing work in io_apic.c
and the NUMA migration feature in the irq tree.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move_irq_desc() will try to move irq_desc to the home node if
the allocated one is not correct, in create_irq_nr().
( This can happen on devices that are on different nodes that
are using MSI, when drivers are loaded and unloaded randomly. )
v2: fix non-smp build
v3: add NUMA_IRQ_DESC to eliminate #ifdefs
[ Impact: improve irq descriptor locality on NUMA systems ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F95EAE.2050903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Try to get irq_desc on the home node in create_irq_nr().
v2: don't check if we can move it when sparse_irq is not used
v3: use move_irq_des, if that node is not what we want
[ Impact: optimization, make MSI IRQ descriptors more NUMA aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F6559F.7070005@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make actual use of the device parameter passed down to
io_apic_set_pci_routing() - to have the IRQ descriptor
on the home node of the device.
If no device has been passed down, we assume it's a platform
device and use the boot node ID for the IRQ descriptor.
[ Impact: optimization, make IO-APIC code more NUMA aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F6557E.3080101@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We want to use dev_to_node() later on, to be aware of the 'home node'
of the GSI in question.
[ Impact: cleanup, prepare the IRQ code to be more NUMA aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Len Brown <lenb@kernel.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
LKML-Reference: <49F65560.20904@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This simplifies the node awareness of the code. All our allocators
only deal with a NUMA node ID locality not with CPU ids anyway - so
there's no need to maintain (and transform) a CPU id all across the
IRq layer.
v2: keep move_irq_desc related
[ Impact: cleanup, prepare IRQ code to be NUMA-aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
LKML-Reference: <49F65536.2020300@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
according to Ingo, change set_affinity() in irq_chip should return int,
because that way we can handle failure cases in a much cleaner way, in
the genirq layer.
v2: fix two typos
[ Impact: extend API ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The original feature of migrating irq_desc dynamic was too fragile
and was causing problems: it caused crashes on systems with lots of
cards with MSI-X when user-space irq-balancer was enabled.
We now have new patches that create irq_desc according to device
numa node. This patch removes the leftover bits of the dynamic balancer.
[ Impact: remove dead code ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F654AF.8000808@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When interrupt-remapping is enabled, we are relying on
setup_IO_APIC_irqs() to configure remapped entries in the
IO-APIC, which comes little bit later after enabling
interrupt-remapping.
Meanwhile, restoration of old io-apic entries after enabling
interrupt-remapping will not make the interrupts through
io-apic functional anyway.
So remove the unnecessary reinit_intr_remapped_IO_APIC() step.
The longer story:
When interrupt-remapping is enabled, IO-APIC entries need to be
setup in the re-mappable format (pointing to
interrupt-remapping table entries setup by the OS). This
remapping configuration is happening in the same place where we
traditionally configure IO-APIC (i.e., in
setup_IO_APIC_irqs()).
So when we enable interrupt-remapping successfully, there is no
need to restore old io-apic RTE entries before we actually do a
complete configuration shortly in setup_IO_APIC_irqs(). Old
IO-APIC RTE's may be in traditional format (non re-mappable) or
in re-mappable format pointing to interrupt-remapping table
entries setup by BIOS. Restoring both of these will not make
IO-APIC functional. We have to rely on setup_IO_APIC_irqs() for
proper configuration by OS.
So I am removing this unnecessary and broken step.
[ Impact: remove unnecessary/broken IO-APIC setup step ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Weidong Han <weidong.han@intel.com>
Cc: dwmw2@infradead.org
LKML-Reference: <20090420200450.552359000@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Address the following complier warning:
arch/x86/kernel/apic/io_apic.c:2543: warning: `eoi_ioapic_irq' defined but not used
By moving that function (and eoi_ioapic_irq()) into an existing
#ifdef CONFIG_INTR_REMAP section of the code.
[ Impact: cleanup ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: dwmw2@infradead.org
Cc: Weidong Han <weidong.han@intel.com>
LKML-Reference: <20090420200450.271099000@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Weidong Han <weidong.han@intel.com>
Shouldn't call ack_apic_edge() in ir_ack_apic_edge(), because
ack_apic_edge() does more than just ack: it also does irq migration
in the non-interrupt-remapping case. But there is no such need for
interrupt-remapping case, as irq migration is done in the process
context.
Similarly, ir_ack_apic_level() shouldn't call ack_apic_level, and
instead should do the local cpu's EOI + directed EOI to the io-apic.
ack_x2APIC_irq() is not neccessary, because ack_APIC_irq() will use MSR
write for x2apic, and uncached write for non-x2apic.
[ Impact: simplify/standardize intr-remap IRQ acking, fix on !x2apic ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: allen.m.kay@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1239957736-6161-3-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As discussed in the thread here:
http://marc.info/?l=linux-kernel&m=123964468521142&w=2
Eric W. Biederman observed:
> It looks like some additional bugs have slipped in since last I looked.
>
> set_irq_affinity does this:
> ifdef CONFIG_GENERIC_PENDING_IRQ
> if (desc->status & IRQ_MOVE_PCNTXT || desc->status & IRQ_DISABLED) {
> cpumask_copy(desc->affinity, cpumask);
> desc->chip->set_affinity(irq, cpumask);
> } else {
> desc->status |= IRQ_MOVE_PENDING;
> cpumask_copy(desc->pending_mask, cpumask);
> }
> #else
>
> That IRQ_DISABLED case is a software state and as such it has nothing to
> do with how safe it is to move an irq in process context.
[...]
>
> The only reason we migrate MSIs in interrupt context today is that there
> wasn't infrastructure for support migration both in interrupt context
> and outside of it.
Yes. The idea here was to force the MSI migration to happen in process
context. One of the patches in the series did
disable_irq(dev->irq);
irq_set_affinity(dev->irq, cpumask_of(dev->cpu));
enable_irq(dev->irq);
with the above patch adding irq/manage code check for interrupt disabled
and moving the interrupt in process context.
IIRC, there was no IRQ_MOVE_PCNTXT when we were developing this HPET
code and we ended up having this ugly hack. IRQ_MOVE_PCNTXT was there
when we eventually submitted the patch upstream. But, looks like I did a
blind rebasing instead of using IRQ_MOVE_PCNTXT in hpet MSI code.
Below patch fixes this. i.e., revert commit 932775a4ab
and add PCNTXT to HPET MSI setup. Also removes copying of desc->affinity
in generic code as set_affinity routines are doing it internally.
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Li Shaohua" <shaohua.li@intel.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: "lcm@us.ibm.com" <lcm@us.ibm.com>
Cc: suresh.b.siddha@intel.com
LKML-Reference: <20090413222058.GB8211@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, no code changed
- syscalls.h update declarations due to unifications
- irq.c declare smp_generic_interrupt() before it gets used
- process.c declare sys_fork() and sys_vfork() before they get used
- tsc.c rename tsc_khz shadowed variable
- apic/probe_32.c declare apic_default before it gets used
- apic/nmi.c prev_nmi_count should be unsigned
- apic/io_apic.c declare smp_irq_move_cleanup_interrupt() before it gets used
- mm/init.c declare direct_gbpages and free_initrd_mem before they get used
Signed-off-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To simplify level irq migration in the presence of interrupt-remapping,
Suresh used a virtual vector (io-apic pin number) to eliminate io-apic
RTE modification. Level triggered interrupt will appear as an edge to
the local apic cpu but still as level to the IO-APIC. So in addition to
do the local apic EOI, it still needs to do IO-APIC directed EOI to clear
the remote IRR bit in the IO-APIC RTE. Pls refer to Suresh's patch for
more details (commit 0280f7c416).
Now interrupt remapping is decoupled from x2apic, it also needs to do the
directed EOI for apic. Otherwise, apic interrupts won't work correctly.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Weidong Han <weidong.han@intel.com>
Cc: suresh.b.siddha@intel.com
Cc: dwmw2@infradead.org
Cc: allen.m.kay@intel.com
LKML-Reference: <1239355037-22856-1-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Cleanup
Reorganizes the code in arch/x86/kernel/io_apic.c by
combining two '#ifdef CONFIG_SMP' regions. In addition
to making the code easier to understand the first
'#ifdef CONFIG_SMP' region is moved to a location later
in the file which will reduce the need for function
forward declarations when the code subsequently revised.
The only changes other than relocating code to a different
position in the file were the removal of the assign_irq_vector()
forward declaration which was no longer needed and some line
length reduction formatting changes.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Cc: lcm@us.ibm.com
LKML-Reference: <20090408210725.GC11159@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
interrupt remapping must be enabled before enabling x2apic, but
interrupt remapping doesn't depend on x2apic, it can be used
separately. Enable interrupt remapping in init_dmars even x2apic
is not supported.
[dwmw2: Update Kconfig accordingly, fix build with INTR_REMAP && !X2APIC]
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch enables suspend/resume for interrupt remapping. During suspend,
interrupt remapping is disabled. When resume, interrupt remapping is enabled
again.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
PCI: fix HT MSI mapping fix
PCI: don't enable too much HT MSI mapping
x86/PCI: make pci=lastbus=255 work when acpi is on
PCI: save and restore PCIe 2.0 registers
PCI: update fakephp for bus_id removal
PCI: fix kernel oops on bridge removal
PCI: fix conflict between SR-IOV and config space sizing
powerpc/PCI: include pci.h in powerpc MSI implementation
PCI Hotplug: schedule fakephp for feature removal
PCI Hotplug: rename legacy_fakephp to fakephp
PCI Hotplug: restore fakephp interface with complete reimplementation
PCI: Introduce /sys/bus/pci/devices/.../rescan
PCI: Introduce /sys/bus/pci/devices/.../remove
PCI: Introduce /sys/bus/pci/rescan
PCI: Introduce pci_rescan_bus()
PCI: do not enable bridges more than once
PCI: do not initialize bridges more than once
PCI: always scan child buses
PCI: pci_scan_slot() returns newly found devices
PCI: don't scan existing devices
...
Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
Impact: get correct smp_affinity as user requested
The effect of setting desc->affinity (ie. from userspace via sysfs) has
varied over time. In 2.6.27, the 32-bit code anded the value with
cpu_online_map, and both 32 and 64-bit did that anding whenever a cpu
was unplugged.
2.6.29 consolidated this into one routine (and fixed hotplug) but
introduced another variation: anding the affinity with cfg->domain.
We should just set it to what the user said - if possible.
(cpu_mask_to_apicid_and already takes cpu_online_mask into account)
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <49C94DDF.2010703@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix bug with irq-descriptor moving when logical flat
Rusty observed:
> The effect of setting desc->affinity (ie. from userspace via sysfs) has varied
> over time. In 2.6.27, the 32-bit code anded the value with cpu_online_map,
> and both 32 and 64-bit did that anding whenever a cpu was unplugged.
>
> 2.6.29 consolidated this into one routine (and fixed hotplug) but introduced
> another variation: anding the affinity with cfg->domain. Is this right, or
> should we just set it to what the user said? Or as now, indicate that we're
> restricting it.
Eric pointed out that desc->affinity should be what the user requested,
if it is at all possible to honor the user space request.
This bug got introduced by commit 22f65d31b "x86: Update io_apic.c to use
new cpumask API".
Fix it by moving the masking to before the descriptor moving ...
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <49C94134.4000408@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move out msi_ir_chip and ir_ioapic_chip from CONFIG_INTR_REMAP shadow
Fix:
arch/x86/kernel/apic/io_apic.c:1431: warning: ‘msi_ir_chip’ defined but not used
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Impact: cleanup
This patch fixes the following sparse warnings:
arch/x86/kernel/apic/io_apic.c:3602:17: warning: symbol 'hpet_msi_type'
was not declared. Should it be static?
arch/x86/kernel/apic/io_apic.c:3467:30: warning: Using plain integer as
NULL pointer
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
LKML-Reference: <1237741871-5827-2-git-send-email-dmitri.vorobiev@movial.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix incorrect error message
- IO APIC resource allocation error message contains one too many "be".
- Print the error message iff there are IO APICs in the system.
I've seen this error message for some time on my x86-32 laptop...
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Alan Bartlett <ajb.stxsl@googlemail.com>
LKML-Reference: <200903202100.30789.bzolnier@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix spurious IRQs
During irq migration, we send a low priority interrupt to the previous
irq destination. This happens in non interrupt-remapping case after interrupt
starts arriving at new destination and in interrupt-remapping case after
modifying and flushing the interrupt-remapping table entry caches.
This low priority irq cleanup handler can cleanup multiple vectors, as
multiple irq's can be migrated at almost the same time. While
there will be multiple invocations of irq cleanup handler (one cleanup
IPI for each irq migration), first invocation of the cleanup handler
can potentially cleanup more than one vector (as the first invocation can
see the requests for more than vector cleanup). When we cleanup multiple
vectors during the first invocation of the smp_irq_move_cleanup_interrupt(),
other vectors that are to be cleanedup can still be pending in the local
cpu's IRR (as smp_irq_move_cleanup_interrupt() runs with interrupts disabled).
When we are ready to unhook a vector corresponding to an irq, check if that
vector is registered in the local cpu's IRR. If so skip that cleanup and
do a self IPI with the cleanup vector, so that we give a chance to
service the pending vector interrupt and then cleanup that vector
allocation once we execute the lowest priority handler.
This fixes spurious interrupts seen when migrating multiple vectors
at the same time.
[ This is apparently possible even on conventional xapic, although to
the best of our knowledge it has never been seen. The stable
maintainers may wish to consider this one for -stable. ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: stable@kernel.org
Impact: fix possible race
save_mask_IO_APIC_setup() was using non atomic memory allocation while getting
called with interrupts disabled. Fix this by splitting this into two different
function. Allocation part save_IO_APIC_setup() now happens before
disabling interrupts.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: cleanup
Clean up #ifdefs and replace them with helper functions.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: simplification
In the current code, for level triggered migration, we need to modify the
io-apic RTE with the update vector information, along with modifying interrupt
remapping table entry(IRTE) with vector and destination. This is to ensure that
remote IRR bit inthe IOAPIC RTE gets cleared when the cpu does EOI.
With this patch, for level triggered, we eliminate the io-apic RTE modification
(with the updated vector information), by using a virtual vector (io-apic pin
number). Real vector that is used for interrupting cpu will be coming from
the interrupt-remapping table entry. Trigger mode in the IRTE will always be
edge, and the actual level or edge trigger will be setup in the IO-APIC RTE.
So a level triggered interrupt will appear as an edge to the local apic
cpu but still as level to the IO-APIC.
With this change, level irq migration can be done by simply modifying
the interrupt-remapping table entry with out changing the io-apic RTE.
And as the interrupt appears as edge at the cpu, in addition to do the
local apic EOI, we need to do IO-APIC directed EOI to clear the remote
IRR bit in the IO-APIC RTE.
This simplies the irq migration in the presence of interrupt-remapping.
Idea-by: Rajesh Sankaran <rajesh.sankaran@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: make kexec work with x2apic
disable_IO_APIC() gets called during crashdump aswell, which configures the
IO-APIC/LAPIC so that legacy interrupts can be delivered for the kexec'd kernel.
In the presence of interrupt-remapping, we need to change the
interrupt-remapping configuration aswell as modifying IO-APIC for virtual wire
B mode.
To keep things simple during the crash, use virtual wire A mode
(for which we don't need to touch io-apic and interrupt-remapping tables).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: interface augmentation (not yet used)
Enable fault handling flow for intr-remapping aswell. Fault handling
code now shared by both dma-remapping and intr-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
arch/x86/kernel/ is getting a bit crowded, and the APIC
drivers are scattered into various different files.
Move them to arch/x86/kernel/apic/*, and also remove
the 'gen' prefix from those which had it.
Also move APIC related functionality: the IO-APIC driver,
the NMI and the IPI code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
