* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (53 commits)
serial: Add driver for the Cell Network Processor serial port NWP device
powerpc: enable dynamic ftrace
powerpc/cell: Fix the prototype of create_vma_map()
powerpc/mm: Make clear_fixmap() actually work
powerpc/kdump: Use ppc_save_regs() in crash_setup_regs()
powerpc: Export cacheable_memzero as its now used in a driver
powerpc: Fix missing semicolons in mmu_decl.h
powerpc/pasemi: local_irq_save uses an unsigned long
powerpc/cell: Fix some u64 vs. long types
powerpc/cell: Use correct types in beat files
powerpc: Use correct type in prom_init.c
powerpc: Remove unnecessary casts
mtd/ps3vram: Use _PAGE_NO_CACHE in memory ioremap
mtd/ps3vram: Use msleep in waits
mtd/ps3vram: Use proper kernel types
mtd/ps3vram: Cleanup ps3vram driver messages
mtd/ps3vram: Remove ps3vram debug routines
mtd/ps3vram: Add modalias support to the ps3vram driver
mtd/ps3vram: Add ps3vram driver for accessing video RAM as MTD
powerpc: Fix iseries drivers build failure without CONFIG_VIOPATH
...
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enables dynamic ftrace. The PowerPC port was dependent on
other code not yet in mainline. Now that the code is, we can now
let PowerPC compile with dynamic ftrace.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The clear_fixmap() routine issues map_page() with flags set to 0.
Currently this causes a BUG_ON() inside the map_page(), as it assumes
that a PTE should be clear before mapping.
This patch makes the map_page() to trigger the BUG_ON() only if the
flags were set.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch replaces internal registers dump implementation with
ppc_save_regs(). From now on PPC64 and PPC32 are using the same
code for crash_setup_regs().
NOTE: The old regs dump implementation was capturing SP (r1) directly
as is, so you could see crash_kexec() function on top of the back-trace.
But ppc_save_regs() goes up one stack frame, so you'll not see it
anymore, at the top-level you'll see who actually triggered the crash
dump instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Freescale PowerPC specific gianfar driver (gig-e) uses
cacheable_memzero for performance reasons we need to export
the symbol to allow the driver to be built as a module.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a brown paper bag from one of my earlier patches that
breaks build on 40x and 8xx.
And yes, I've now added 40x and 8xx to my list of test configs :-)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[Split from a larger patch - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
in/out_be64() work on u64s.
The first parameter to ppc_md.ioremap is a phys_addr_t.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Only pass the address of a u64 if that is what the function requires.
[Split out of a larger patch - sfr]
[update comment - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
tce_entryp is a "u64 *" not an "unsigned long *".
[Split from a large patch -sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
of_get_flat_dt_prop() returns a "void *", so we don't need to cast when
assigning its result to a pointer variable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update ps3vram driver to use the new ps3 three id modalias support.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add ps3vram driver, which exposes unused video RAM on the PS3 as a MTD
device suitable for storage or swap. Fast data transfer is achieved
using a local cache in system RAM and DMA transfers via the GPU.
Signed-off-by: Vivien Chappelier <vivien.chappelier@free.fr>
Signed-off-by: Jim Paris <jim@jtan.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
iSeries dependent drivers fail to build, when CONFIG_VIOPATH is disabled.
Fix the problem by making those drivers select it.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable RELOCATABLE option if user selects CRASH_DUMP option. Without this
patch user has to first select RELOCATABLE option and then has to enable
CRASH_DUMP option.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So change the flags member of struct spu from u64 to unsigned long.
This change will also prevent some warnings when we change u64 to unsigned
long long.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These ioctls take a struct serial_rs485
(see linux/serial.h) as argument. They are already available
on x86. This patch adds them for the powerpc architecture.
Signed-off-by: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
X has been failing to start on my quad G5 powermac since commit
1fd0f52583 ("powerpc: Fix domain numbers
in /proc on 64-bit") went in. The reason is that the change allows X
to see the PCI-PCI bridge above the video card (previously it was
obscured by the fact that there were two "00" directories in
/proc/bus/pci), and the pciconfig_iobase system call on the bridge is
failing because of a hack that we have to return information about the
AGP bus when X asks about bus 0. This machine doesn't have an AGP bus
(it has PCI Express) and so the pciconfig_iobase call is returning -1,
which ultimately causes X to fail to start.
This fixes it by checking that we have an AGP bridge before
redirecting the pciconfig_iobase call to return information about the
AGP bus. With this, X starts successfully both on a quad G5 with
PCI Express and on an older dual G5 with AGP.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SPIN_LOCK_UNLOCKED is deprecated. The following makes the change suggested
in Documentation/spinlocks.txt
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
declarer name DEFINE_SPINLOCK;
identifier xxx_lock;
@@
- spinlock_t xxx_lock = SPIN_LOCK_UNLOCKED;
+ DEFINE_SPINLOCK(xxx_lock);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SPIN_LOCK_UNLOCKED is deprecated. The following makes the change suggested
in Documentation/spinlocks.txt
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
declarer name DEFINE_SPINLOCK;
identifier xxx_lock;
@@
- spinlock_t xxx_lock = SPIN_LOCK_UNLOCKED;
+ DEFINE_SPINLOCK(xxx_lock);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code for providing processor cache information in sysfs
has the following deficiencies:
- several complex functions that are hard to understand
- implicit recursion (cache_desc_release -> kobject_put -> cache_desc_release)
- explicit recursion (create_cache_index_info)
- use of two per-cpu arrays when one would suffice
- duplication of work on systems where CPUs share cache
Also, when I looked at implementing support for a shared_cpu_map
attribute, it was pretty much impossible to handle hotplug without
checking every single online CPU's cache_desc list and fixing things
up... not that this is a hot path, but it would have introduced
O(n^2)-ish behavior during boot. Addressing this involved rethinking
the core data structures used, which didn't lend itself to an
incremental approach.
This implementation maintains a "forest" (potentially more than one
tree) of cache objects which reflects the system's cache topology.
Cache objects are instantiated as needed as CPUs come online. A
per-cpu array is used mainly for sysfs-related bookkeeping; the
objects in the array just point to the appropriate points in the
forest.
This maintains compatibility with the existing code and includes some
enhancements:
- Implement the shared_cpu_map attribute, which is essential for
enabling userspace to discover the system's overall cache topology.
- Use cache-block-size properties if cache-line-size is not available.
I chose to place this implementation in a new file since it would have
roughly doubled the size of sysfs.c, which is already kind of messy.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The non-zero return from the prepare callback is returned by sys_kexec_load()
to userspace, indicating that kexec is not supported on the machine.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch makes the default install script (arch/powerpc/boot/install.sh)
copy the bootable image files into the install directory. Before this
patch only the vmlinux image file was copied.
This patch makes the default 'make install' command useful for embedded
development when $(INSTALL_PATH) is set in the environment.
As a side effect, this patch changes the calling convention of the
install.sh script. Instead of a single 5th parameter, the script is now
passed a list of all the target images stored in the $(image-y) Makefile
variable. This should be backwards compatible with existing install scripts
since it just adds additional arguments and does not change existing ones.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Both users of careful_allocation() immediately memset() the
result. So, just do it in one place.
Also give careful_allocation() a 'z' prefix to bring it in
line with kzmalloc() and friends.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we memset() the result in both of the uses here,
just make careful_alloc() return a virtual address.
Also, add a separate variable to store the physial
address that comes back from the lmb_alloc() functions.
This makes it less likely that someone will screw it up
forgetting to convert before returning since the vaddr
is always in a void* and the paddr is always in an
unsigned long.
I admit this is arbitrary since one of its users needs
a paddr and one a vaddr, but it does remove a good
number of casts.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we fail a bootmem allocation, the bootmem code itself
panics. No need to redo it here.
Also change the wording of the other panic. We don't
strictly have to allocate memory on the specified node.
It is just a hint and that node may not even *have* any
memory on it. In that case we can and do fall back to
other nodes.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The behavior in careful_allocation() really confused me
at first. Add a comment to hopefully make it easier
on the next doofus that looks at it.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes some unbalanced OF node references in the
powermac code
Signed-off-by: Nicolas Palix <npalix@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There's a problem on some embedded platforms when we re-assign
everything on PCI, such as 44x. The generic code tries to avoid
assigning devices to addresses overlapping the low legacy
addresses such as VGA hard decoded areas using constants that
are unfortunately no good for us, as they don't take into account
the address translation we do to access PCI busses.
Thus we end up allocating things like IO BARs to 0, which is
technically legal, but will shadow hard decoded ports for use
by things like VGA cards.
This works around it by attempting to reserve legacy regions
before we try to assign addresses.
NOTE: This may have nasty side effects in cases I haven't tested
yet:
- We try to use FW mappings (ie. powermac) and the FW has allocated
a conflicting address over those legacy regions. This will typically
happen. I would expect the new code to just fail with an informative
message without harm but I haven't had a chance to test that scenario
yet.
- A device with fixed BARs overlapping those legacy addresses such
as an IDE controller in legacy mode is in the system. I don't know
for sure yet what will happen there, I have to test :-)
Ideally, we should change PCIBIOS_MIN_IO/MIN_MEM accross the board
to take a bus pointer so they can provide appropriate per-bus translated
values to the generic code but that's a more invasive patch. I will
do that in the future, but in the meantime, this fixes the problem
locally
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Use the generic pci_swizzle_interrupt_pin() instead of arch-specific code.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A published errata for ppc440epx states, that when running Linux with
both EHCI and OHCI modules loaded, the EHCI module experiences a fatal
error when a high-speed device is connected to the USB2.0, and
functions normally if OHCI module is not loaded.
There used to be recommendation to use only hi-speed or full-speed
devices with specific conditions, when respective module was unloaded.
Later, it was observed that ohci suspend is enough to keep things
going, and it was turned into workaround, as explained below.
Quote from original descriprion:
The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In
USB 2.0 Host controllers, each EHCI controller has one or more companion
controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will
contain one or more ports. For each port, only one of the controllers
is connected at any one time. In the 440EPx, there is only one OHCI
companion controller, and only one USB 2.0 Host port.
All ports on an USB 2.0 controller default to the companion
controller. If you load only an ohci driver, it will have control of
the ports and any deviceplugged in will operate, although high speed
devices will be forced to operate at full speed. When an ehci driver
is loaded, it explicitly takes control of the ports. If there is a
device connected, and / or every time there is a new device connected,
the ehci driver determines if the device is high speed or not. If it
is high speed, the driver retains control of the port. If it is not,
the driver explicitly gives the companion controller control of the
port.
The is a software workaround that uses
Initial version of the software workaround was posted to
linux-usb-devel:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html
and later available from amcc.com:
http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2
The patch below is generally based on the latter, but reworked to
powerpc/of_device USB drivers, and uses a few devicetree inquiries to
get rid of (some) hardcoded defines.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add kprobe_insn_mutex for protecting kprobe_insn_pages hlist, and remove
kprobe_mutex from architecture dependent code.
This allows us to call arch_remove_kprobe() (and free_insn_slot) while
holding kprobe_mutex.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h. Move the type definition
to linux/types.h to break the loop.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Show node to memory section relationship with symlinks in sysfs
Add /sys/devices/system/node/nodeX/memoryY symlinks for all
the memory sections located on nodeX. For example:
/sys/devices/system/node/node1/memory135 -> ../../memory/memory135
indicates that memory section 135 resides on node1.
Also revises documentation to cover this change as well as updating
Documentation/ABI/testing/sysfs-devices-memory to include descriptions
of memory hotremove files 'phys_device', 'phys_index', and 'state'
that were previously not described there.
In addition to it always being a good policy to provide users with
the maximum possible amount of physical location information for
resources that can be hot-added and/or hot-removed, the following
are some (but likely not all) of the user benefits provided by
this change.
Immediate:
- Provides information needed to determine the specific node
on which a defective DIMM is located. This will reduce system
downtime when the node or defective DIMM is swapped out.
- Prevents unintended onlining of a memory section that was
previously offlined due to a defective DIMM. This could happen
during node hot-add when the user or node hot-add assist script
onlines _all_ offlined sections due to user or script inability
to identify the specific memory sections located on the hot-added
node. The consequences of reintroducing the defective memory
could be ugly.
- Provides information needed to vary the amount and distribution
of memory on specific nodes for testing or debugging purposes.
Future:
- Will provide information needed to identify the memory
sections that need to be offlined prior to physical removal
of a specific node.
Symlink creation during boot was tested on 2-node x86_64, 2-node
ppc64, and 2-node ia64 systems. Symlink creation during physical
memory hot-add tested on a 2-node x86_64 system.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The KernelPageSize entry in /proc/pid/smaps is the pagesize used by the
kernel to back a VMA. This matches the size used by the MMU in the
majority of cases. However, one counter-example occurs on PPC64 kernels
whereby a kernel using 64K as a base pagesize may still use 4K pages for
the MMU on older processor. To distinguish, this patch reports
MMUPageSize as the pagesize used by the MMU in /proc/pid/smaps.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: "KOSAKI Motohiro" <kosaki.motohiro@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix misspelling of "firmware" in powerpc Makefile
It's spelled "firmware".
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
... and don't bother in callers. Don't bother with zeroing i_blocks,
while we are at it - it's already been zeroed.
i_mode is not worth the effort; it has no common default value.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
