Commit 234b6ceddb
clocksource: convert ARM 32-bit up counting clocksources
broke the build for ixp4xx and made big endian operation impossible.
This commit restores the original behaviour.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
[ Thomas says that we might want to have generic BE accessor functions
to the MMIO clock source, but that hasn't happened yet, so in the
meantime this seems to be the short-term fix for the particular
problem - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only let the rx parser be enabled if it is necessary (if VLAN extraction,
IP or TCP checksumming or the rx queue filer are enabled). Otherwise
disable it.
The new routine gfar_check_rx_parser_mode should be run after every
change on this features and will enable/disable the parser as necessary.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in arch/mips/kernel/i8259.c still hasn't been converted to
using struct syscore_ops instead of a sysdev for resume and shutdown.
As a result, this code doesn't build any more after suspend, resume
and shutdown callbacks have been removed from struct sysdev_class.
Fix this problem by converting i8259.c to using syscore_ops.
Reported-and-tested-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (adm1275) Fix coefficients per datasheet revision B
hwmon: (pmbus) Use long variables for register to data conversions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fix loop checks in d_materialise_unique()
Fix ->d_lock locking order in unlazy_walk()
* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-2.6-rcu:
rcu: Prevent RCU callbacks from executing before scheduler initialized
Commit 3fe1698b7f ("sched: Deal with non-atomic min_vruntime reads
on 32bit") forgot to initialize min_vruntime_copy which could lead to
an infinite while loop in task_waking_fair() under some circumstances
(early boot, lucky timing).
[ This bug was also reported by others that blamed it on the RCU
initialization problems ]
Reported-and-tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When receiving the first RX interrupt before the internal call
to napi_schedule_prep is successful the RX interrupt gets disabled
and is never enabled again as the poll function never gets executed.
Signed-off-by: Michael Thalmeier <Michael.Thalmeier@sigmatek.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coefficients to convert chip register values to voltage/current have been
slightly changed in revision B of the chip datasheet. Update driver coefficients
to match the coefficients in the datasheet.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Include the device id in the bus-id to give userspace a way to open
the correct "cardN" when there are multiple device instances.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Both __d_unalias() and __d_materialise_dentry() need loop prevention.
Grab rename_lock in caller, check for loops there...
As a side benefit, we have dentry_lock_for_move() called only under
rename_lock, which seriously reduces deadlock potential of the
execrable "locking order" used for ->d_lock.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
There is no software fallback implemented for SCTP or FCoE checksumming,
and so it should not be passed on by software devices like bridge or bonding.
For VLAN devices, this is different. First, the driver for underlying device
should be prepared to get offloaded packets even when the feature is disabled
(especially if it advertises it in vlan_features). Second, devices under
VLANs do not get replaced without tearing down the VLAN first.
This fixes a mess I accidentally introduced while converting bonding to
ndo_fix_features.
NETIF_F_SOFT_FEATURES are removed from BOND_VLAN_FEATURES because they
are unused as of commit 712ae51afd.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets to devices without NETIF_F_SCTP_CSUM (including NETIF_F_NO_CSUM)
should be properly checksummed because the packets can be diverted or
rerouted after construction. This still leaves packets diverted from
NETIF_F_SCTP_CSUM-enabled devices with broken checksums. Fixing this
needs implementing software offload fallback in networking core.
For users of sctp_checksum_disable, skb->ip_summed should be left as
CHECKSUM_NONE and not CHECKSUM_UNNECESSARY as per include/linux/skbuff.h.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: Resolve inode eviction and ail list interaction bug
GFS2: Fix race during filesystem mount
GFS2: force a log flush when invalidating the rindex glock
This patch contains a few misc fixes which resolve a recently
reported issue. This patch has been a real team effort and has
received a lot of testing.
The first issue is that the ail lock needs to be held over a few
more operations. The lock thats added into gfs2_releasepage() may
possibly be a candidate for replacing with RCU at some future
point, but at this stage we've gone for the obvious fix.
The second issue is that gfs2_write_inode() can end up calling
a glock recursively when called from gfs2_evict_inode() via the
syncing code, so it needs a guard added.
The third issue is that we either need to not truncate the metadata
pages of inodes which have zero link count, but which we cannot
deallocate due to them still being in use by other nodes, or we need
to ensure that those pages have all made it through the journal and
ail lists first. This patch takes the former approach, but the
latter has also been tested and there is nothing to choose between
them performance-wise. So again, we could revise that decision
in the future.
Also, the inode eviction process is now better documented.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Tested-by: Bob Peterson <rpeterso@redhat.com>
Tested-by: Abhijith Das <adas@redhat.com>
Reported-by: Barry J. Marson <bmarson@redhat.com>
Reported-by: David Teigland <teigland@redhat.com>
We've tried several times to make this machine 'just work', but every
patch that does causes many other machines to fail. This adds a quirk
which special cases this hardware and forces ssc to be
disabled. There's no way to override this from the command line; that
would be a significantly more invasive change.
This patch fixes#36656 on fdo bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=36656
Signed-off-by: Keith Packard <keithp@keithp.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36656
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the fence of the new frontbuffer, if any.
Generating a new fence could cause us to wait for completely unrelated
rendering to finish before performing the flip.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of ssh://master.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6: (52 commits)
drm/i915: provide module parameter description
drm/i915: add module parameter compiler hints
drm/i915/bios: Avoid temporary allocation whilst searching for downclock
drm/i915: Cache GT fifo count for SandyBridge
i915: Fix opregion notifications
drm/i915: TVDAC_STATE_CHG does not indicate successful load-detect
drm/i915: Select correct pipe during TV detect
drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
Revert "drm/i915: enable rc6 by default"
drm/i915: Clean up i915_driver_load failure path
drm/i915: Enable i915 frame buffer compression by default
drm/i915: Share the common work of disabling active FBC before updating
drm/i915: Perform intel_enable_fbc() from a delayed task
drm/i915: Disable FBC across page-flipping
drm/i915: Set persistent-mode for ILK/SNB framebuffer compression
drm/i915: Use of a CPU fence is mandatory to update FBC regions upon CPU writes
drm/i915: Remove vestigial pitch from post-gen2 FBC control routines
drm/i915: Replace direct calls to vfunc.disable_fbc with intel_disable_fbc()
drm/i915: Only export the generic intel_disable_fbc() interface
drm/i915: Enable GPU reset on Ivybridge.
...
Commit 28c2103 added new state ACPI_STATE_D3_COLD, so the device power
states array must be expanded by one also.
v2: Use ACPI_D_STATE_COUNT instead of number 5 for the array size.
Reported-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The firmware on some machine will report duplicated hardware error
source ID in HEST. This is considered a firmware bug. To provide
better warning message, this patch adds duplicated hardware error
source ID detecting and corresponding printk.
This patch fixes#37412 on kernel bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=37412
Reported-by: marconifabio@ubuntu-it.org
Signed-off-by: Huang Ying <ying.huang@intel.com>
Tested-by: Mathias <janedo.spam@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As Simon reported, digital TV broke with mt20xx tuner due to
commit ad020dc2fe.
The mt20xx tuner passes V4L2_TUNER_DIGITAL_TV to tuner core. However, the
check_mode code now doesn't handle it well. Change the logic there to
avoid the breakage, and fix a test for analog-only at g_tuner.
Reported-by: Simon Arlott <simon@fire.lp0.eu>
Tested-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Attached is a patch which addresses a race condition in the DVB core
related to closing/reopening the DVB frontend device in quick
succession. This is the reason that devices such as the HVR-1300,
HVR-3000, and HVR-4000 have been failing to scan properly under MythTV
and w_scan.
The gory details of the race are described in the patch.
Devin
There is a race condition exhibited when channel scanners such as w_scan and
MythTV quickly close and then reopen the frontend device node.
Under normal conditions, the behavior is as follows:
1. Application closes the device node
2. DVB frontend ioctl calls dvb_frontend_release which sets
fepriv->release_jiffies
3. DVB frontend thread *eventually* calls dvb_frontend_is_exiting() which
compares fepriv->release_jiffies, and shuts down the thread if timeout has
expired
4. Thread goes away
5. Application opens frontend device
6. DVB frontend ioctl() calls ts_bus_ctrl(1)
7. DVB frontend ioctl() creates new frontend thread, which calls
dvb_frontend_init(), which has demod driver init() routine setup initial
register state for demod chip.
8. Tuning request is issued.
The race occurs when the application in step 5 performs the new open() call
before the frontend thread is shutdown. In this case the ts_bus_ctrl() call
is made, which strobes the RESET pin on the demodulator, but the
dvb_frontend_init() function never gets called because the frontend thread
hasn't gone away yet. As a result, the initial register config for the demod
is *never* setup, causing subsequent tuning requests to fail.
If there is time between the close and open (enough for the dvb frontend
thread to be torn down), then in that case the new frontend thread is created
and thus the dvb_frontend_init() function does get called.
The fix is to set the flag which forces reinitialization if we did in fact
call ts_bus_ctrl().
This problem has been seen on the HVR-1300, HVR-3000, and HVR-4000, and is
likely occuring on other designs as well where ts_bus_ctrl() actually strobes
the reset pin on the demodulator.
Note that this patch should supercede any patches submitted for the
1300/3000/4000 which remove the code that removes GPIO code in
cx8802_dvb_advise_acquire(), which have been circulating by users for some
time now...
Canonical tracking this issue in Launchpad 439163:
Thanks to Jon Sayers from Hauppauge and Florent Audebert from Anevia S.A. for
providing hardware to test/debug with.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jon Sayers <j.sayers@hauppauge.co.uk>
Cc: Florent Audebert <florent.audebert@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When CONFIG_SND is not enabled, radio-sf16fmr2 build fails with:
so make this driver depend on SND.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: Fix use of static variable in rpcb_getport_async
NFSv4.1: update nfs4_fattr_bitmap_maxsz
SUNRPC: Fix a race between work-queue and rpc_killall_tasks
pnfs: write: Set mds_offset in the generic layer - it is needed by all LDs
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/evergreen: emit SQ_LDS_RESOURCE_MGMT for blits
agp/intel: Fix typo in G4x_GMCH_SIZE_VT_2M
drm/radeon/kms: fix typo in read_disabled vbios code
drm/radeon/kms: use correct BUS_CNTL reg on rs600
drm/radeon/kms: fix backend map typo on juniper
drm/radeon/kms: fix regression in hotplug
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
slip: fix wrong SLIP6 ifdef-endif placing
natsemi: fix another dma-debug report
sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
net: Fix default in docs for tcp_orphan_retries.
hso: fix a use after free condition
net/natsemi: Fix module parameter permissions
XFRM: Fix memory leak in xfrm_state_update
sctp: Enforce retransmission limit during shutdown
mac80211: fix TKIP replay vulnerability
mac80211: fix ie memory allocation for scheduled scans
ssb: fix init regression of hostmode PCI core
rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
carl9170: add NEC WL300NU-AG usbid
cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
ath5k: fix incorrect use of drvdata in PCI suspend/resume code
ath5k: fix incorrect use of drvdata in sysfs code
Bluetooth: Fix memory leak under page timeouts
Bluetooth: Fix regression with incoming L2CAP connections
Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
...
Alan Cox reported a missing check on the kmalloc return value for the
allocation of a temporary mode used for searching for the LVDS downlock
frequency. This allocation is roughly 200 bytes, a little too large to
friviously place on the stack. However, we can simply use the few bytes
we need stored within the original DVO timing data, skip the translation
and do the compare directly between the timing data rather than on a
mode, thus avoiding the need for any temporary allocations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.
On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.
This fixes a regression introduced in 3.0-rc1 by 08ee80cc39
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All ACPICA locks are allocated by the same function,
acpi_os_create_lock(), with the help of a local variable called
"lock". Thus, when lockdep is enabled, it uses "lock" as the
name of all those locks and regards them as instances of the same
lock, which causes it to report possible locking problems with them
when there aren't any.
To work around this problem, define acpi_os_create_lock() as a macro
and make it pass its argument to spin_lock_init(), so that lockdep
uses it as the name of the new lock. Define this macron in a
Linux-specific file, to minimize the resulting modifications of
the OS-independent ACPICA parts.
This change is based on an earlier patch from Andrea Righi and it
addresses a regression from 2.6.39 tracked as
https://bugzilla.kernel.org/show_bug.cgi?id=38152
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Tested-by: Andrea Righi <andrea@betterlinux.com>
Reviewed-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The read back of the available FIFO entries is vital for system
stability, but extremely costly. However, we only need a guide so as to
avoid eating into the reserved entries and since we are the only
consumer we can cache the read of the count from the last write.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
opregion-based platforms will send ACPI video event 0x80 for a range of
notification types for legacy compatibility. This is interpreted as a
display switch event, which may not be appropriate in the circumstances.
When we receive such an event we should make sure that the platform is
genuinely requesting a display switch before passing that event through
to userspace.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Do not use this bit to indicate that load detection has completed,
instead just wait for vblank, at which point the load registers will
have been updated.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Yi Sun <yi.sun@intel.com>
Under some rare but real combinations of configuration parameters, RCU
callbacks are posted during early boot that use kernel facilities that
are not yet initialized. Therefore, when these callbacks are invoked,
hard hangs and crashes ensue. This commit therefore prevents RCU
callbacks from being invoked until after the scheduler is fully up and
running, as in after multiple tasks have been spawned.
It might well turn out that a better approach is to identify the specific
RCU callbacks that are causing this problem, but that discussion will
wait until such time as someone really needs an RCU callback to be invoked
(as opposed to merely registered) during early boot.
Reported-by: julie Sullivan <kernelmail.jms@gmail.com>
Reported-by: RKK <kulkarni.ravi4@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: julie Sullivan <kernelmail.jms@gmail.com>
Tested-by: RKK <kulkarni.ravi4@gmail.com>
drm_pci_device_is_pcie duplicates the funcationality of pci_is_pcie.
Convert callers of the former to the latter. This has the side benefit
of removing an unnecessary search in the PCI configuration space due to
using a saved PCIe capability offset.
[airlied: update for new callsite]
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Resize feature was supported by the commit 4e33f9eab0 but it was not
reflected to the list of unsupported features in nilfs2.txt file.
This updates the list to fix discrepancy.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Compute drivers may change this, so make sure to emit it to
avoid errors in bo blits.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=39119
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Konstantin Belousov found an error in the define of G4x_GMCH_SIZE_VT_2M
relative to the GMCH specs, and confirmed that indeed one of his users
with a Q45 reports 0xb not 0xc for a 2/2MiB GATT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Konstantin Belousov <kostikbel@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
