* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: Change link order of pciehp & acpiphp
PCI hotplug: fakephp: Allocate PCI resources before adding the device
PCI MSI: Fix undefined shift by 32
PCI PM: Do not wait for buses in B2 or B3 during resume
PCI PM: Power up devices before restoring their state
PCI PM: Fix hibernation breakage on EeePC 701
PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
PCI PM: Fix suspend error paths and testing facility breakage
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
powerpc: Fix oops on some machines due to incorrect pr_debug()
powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
powerpc/5200: update device tree binding documentation
powerpc/5200: Bugfix for PCI mapping of memory and IMMR
powerpc/5200: update defconfigs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
pxamci: enable DMA for write ops after CMD/RESP
pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x())
ricoh_mmc: Use suspend_late/resume_early
mmci: Add support for ST Micro derivate
mmc: Add a MX2/MX3 specific SDHC driver
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
icside: fix PCB version 6 support (v2)
tx4939ide: typo fix and minor cleanup
ide: add CS5536 host driver (v3)
ide: Force VIA IDE legacy interrupts for AmigaOne boards
IDE: Unregister and disable devices if initialization fails.
ide: fix ide_register_port() failure handling
ide: struct device - replace bus_id with dev_name(), dev_set_name()
ide-cd: fix DMA for non bio-backed requests
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
uwb: lock rc->rsvs_lock with spin_lock_bh()
wusb: timeout when waiting for ASL/PZL updates in whci-hcd
uwb: remove unused #include <version.h>'s
wusb: return -ENOTCONN when resetting a port with no connected device
uwb: safely remove all reservations
The host really shouldn't be notifying us of config changes
before the device status is VIRTIO_CONFIG_S_DRIVER or
VIRTIO_CONFIG_S_DRIVER_OK.
However, if we do happen to be interrupted while we're not
attached to a driver, we really shouldn't oops. Prevent
this simply by checking that device->driver is non-NULL
before trying to notify the driver of config changes.
Problem observed by doing a "set_link virtio.0 down" with
QEMU before the net driver had been loaded.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the PXA270 MMC hardware, there seems to be an issue of
data corruption on writes where a 4KB data block is offset
by one byte.
If we delay enabling the DMA for writes until after the CMD/RESP
has finished, the problem seems to be fixed.
related to PXA270 Erratum #91
Tested-by: Vernon Sauder <VernonInHand@gmail.com>
Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
If ricoh_mmc suspends before sdhci_pci, it will pull the card
out from under the controller, which could leave the system in
a very confused state.
Using suspend_late/resume_early ensures that sdhci_pci suspends first
and resumes second.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds support for the ST Microelectronics version of
the PL180 PrimeCell. They use designer ID 0x80 and have a few
alterations/bugfixes related to open drain and HW flow control.
They also add some SDIO registers, I am unsure if these are
in ST HW only or if this is things also added in later ARM
revisions, but they are included in the mmci.h file for
completeness.
Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
We need to pass struct ide_port_info also to ide_host_register().
v2:
Fix v5/v6 mismatch noticed by Russell.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The bcount is greater than 0 and less than or equal to 0x10000.
Thus '(bcount & 0xffff) == 0x0000' can be simplified as 'bcount == 0x10000'.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is a port of libata's pata_cs5536.c (written by Martin K. Petersen)
to IDE subsystem.
Changes done while at it:
* Reprogram PIO/MWDMA timings if needed before and after DMA transfer
(chipset uses shared PIO/MWDMA timings).
* Fix cable detection to report 80-wires cable if BIOS set it for any
device on a port (IDE core will do drive-side cable detection later).
* Don't disable UDMA while programming PIO timings.
* Simplify PCI/MSR support.
Pros of having IDE host driver in addition to libata's one:
* IDE is much lighter than SCSI+libata, the host driver itself is also
a bit smaller:
text data bss dec hex filename
1261 496 4 1761 6e1 drivers/ata/pata_cs5536.o
1242 128 4 1374 55e drivers/ide/cs5536.o
* This allows use of IDE features which are unavailable under libata.
v2:
* Fixes per review from Sergei:
- simplify dependency check in Kconfig
- use IDE_DRV_MASK also for ->drive_data
- disable UDMA when programming MWDMA
- program new DTC timings only when necessary
- fix printk() level in cs5536_init_one()
* Fix patch description according to comments from Alan and Sergei.
v3:
* Smarter masking of UDMA bits per Sergei's suggestion.
Cc: Martin K. Petersen <mkp@mkp.net>
Cc: Karl Auerbach <karl@iwl.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The AmigaOne uses the onboard VIA IDE controller in legacy mode (like the
Pegasos).
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On reboot the loop in device_shutdown gets confused by these partially
initialized devices and goes into an infinite loop. Therefore unregister
and disable these devices.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
[bart: remove leftover hwif->present clearing + update patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out port freeing from ide_host_free() to ide_free_port().
* Add ide_disable_port() and use it on ide_register_port() failure.
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since the complete re-write in 2.6.10, some PowerMacs (At least PowerMac 5500
and PowerMac G3 Beige rev A) with ATI Mach64 chip have suffered from unstable
columns in their framebuffer image. This seems to depend on a value (4) read
from PLL_EXT_CNTL register, which leads to incorrect DSP config parameters to
be written to the chip. This patch uses a value calculated by aty_init_pll_ct
instead, as a starting point.
There are questions as to whether this should be extended to other platforms
or maybe made dependent on specific chip types, but in the meantime, this has
been tested on various powermacs and works for them so let's commit it.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Tested-by: Michael Pettersson <mike@it.uu.se>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Just like with the s5h1411, the s5h1409 needs a soft-reset in order for it
to know that the tuner has been told to change frequencies. This change
changes the behavior from "random tuning times between 500ms to complete
tuning lock failures" to "tuning lock consistently within 700ms".
Thanks to Robert Krakora <rob.krakora@messagenetsystems.com> for doing
initial testing of the patch on the KWorld 330U.
Thanks to Andy Walls <awalls@radix.net> for doing testing of the patch on
the HVR-1600.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for doing additional testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According with saa7130 public datasheet, saa7130 doesn't support
digital audio. This is also confirmed by experimental tests. So, it
doesn't make sense to let saa7134-alsa register for those chipsets.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 setup: fix asm constraints in vesa_store_edid
xen: make sysfs files behave as their names suggest
x86: tone down mtrr_trim_uncached_memory() warning
x86: correct the CPUID pattern for MSR_IA32_MISC_ENABLE availability
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
leds: Fix bounds checking of wm8350->pmic.led
regulator: move bq24022 init back to module_init instead of subsys_initcall
Fix an off-by-two memory error in console selection.
The loop below goes from sel_start to sel_end (inclusive), so it writes
one more character. This one more character was added to the allocated
size (+1), but it was not multiplied by an UTF-8 multiplier.
This patch fixes a memory corruption when UTF-8 console is used and the
user selects a few characters, all of them 3-byte in UTF-8 (for example
a frame line).
When memory redzones are enabled, a redzone corruption is reported.
When they are not enabled, trashing of random memory occurs.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
igb: fix link reporting when using sgmii
igb: prevent skb_over panic w/ mtu smaller than 1K
igb: Fix DCA errors and do not use context index for 82576
ipv6: compile fix for ip6mr.c
packet: Avoid lock_sock in mmap handler
sfc: Replace stats_enabled flag with a disable count
sfc: SFX7101/SFT9001: Fix AN advertisements
sfc: SFT9001: Always enable XNP exchange on SFT9001 rev B
sfc: Update board info for hardware monitor on SFN4111T-R5 and later
sfc: Test for PHYXS faults whenever we cannot test link state bits
sfc: Reinitialise the PHY completely in case of a PHY or NIC reset
sfc: Fix post-reset MAC selection
sfc: SFN4111T: Fix GPIO sharing between I2C and FLASH_CFG_1
sfc: SFT9001: Fix speed reporting in 1G PHY loopback
sfc: SFX7101: Remove workaround for bad link training
sfc: SFT9001: Enable robust link training
sky2: fix hard hang with netconsoling and iface going up
The mmap_region() code would temporarily set the VM_ACCOUNT flag for
anonymous shared mappings just to inform shmem_zero_setup() that it
should enable accounting for the resulting shm object. It would then
clear the flag after calling ->mmap (for the /dev/zero case) or doing
shmem_zero_setup() (for the MAP_ANON case).
This just resulted in vma merge issues, but also made for just
unnecessary confusion. Use the already-existing VM_NORESERVE flag for
this instead, and let shmem_{zero|file}_setup() just figure it out from
that.
This also happens to make it obvious that the new DRI2 GEM layer uses a
non-reserving backing store for its object allocation - which is quite
possibly not intentional. But since I didn't want to change semantics
in this patch, I left it alone, and just updated the caller to use the
new flag semantics.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using sgmii the link was not being properly passed up to the driver
from the underlying link management functions. This change corrects it so
that get_link_status is cleared when a link has been found.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A panic has been observed with frame sizes smaller than 1K. This has been
root caused to the hardware spanning larger frames across multiple buffers
and then reporting the original frame size in the first descriptor. To
prevent this we can enable set the LPE bit which in turn will restrict
packet sizes to those set in the RLPML register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82576 was being incorrectly flagged as needing a context index. It does not as
each ring has it's own table of 2 contexts.
Driver was registering after registering the driver instead of the other way around.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use a spin-lock to serialise statistics fetches and also
to inhibit them for short periods of time, plus a flag to
enable/disable statistics fetches for longer periods of time, during
online reset. This was apparently insufficient to deal with the several
reasons for stats being disabled.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 10Xpress PHYs require autonegotiation all the time; enforce this
in the set_settings() method and do not treat it as a workaround.
Remove claimed support for 100M HD mode since it is not supported by
current firmware.
Do not set speed override bits when AN is enabled, and do not use
register 1.49192 for AN configuration as it can override what we set
elsewhere.
Always set the AN selector bits to 1 (802.3).
Fix confusion between Next Page and Extended Next Page.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround is not specific to rev A.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the loopback mode, there may be no pertinent link state
bits. In this case we test the PHYXS RX fault bit instead. Make
sure to do this in all cases where there are no link state bits.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, set pause advertising bits properly.
A PHY reset is not necessary to recover from the register self-test,
so use a "invisible" reset there instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify falcon_switch_mac() to always set NIC_STAT_REG, even if the the
MAC is the same as it was before. This ensures that the value is
correct after an online reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change sfn4111t_reset() to change only GPIO output enables so that it
doesn't break subsequent I2C operations.
Update comments to explain exactly what we're doing.
Add a short sleep to make sure the FLASH_CFG_1 value is latched before
any subsequent I2C operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of disabling AN in loopback, just prevent restarting AN and
override the speed in sft9001_get_settings().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Early versions of the SFX7101 firmware could complete link training in
a state where it would not adequately cancel noise (Solarflare bug
10750). We previously worked around this by resetting the PHY after
seeing many Ethernet CRC errors. This workaround is unsafe since it
takes no account of the interval between errors; it also appears to
be unnecessary with production firmware. Therefore remove it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable a firmware option that appears to be necessary for reliable
operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing anything over netconsole before hw is up and running is,
of course, not going to work.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround was needed when regulator/ was not linked before both
power/ and usb/otg/ in drivers/Makefile. Now that it is even linked
before mfd/, this patch makes sure that bq24022 isn't probed before the
GPIO expander is set up.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tulip: fix 21142 with 10Mbps without negotiation
drivers/net/skfp: if !capable(CAP_NET_ADMIN): inverted logic
gianfar: Fix Wake-on-LAN support
smsc911x: timeout reaches -1
smsc9420: fix interrupt signalling test failures
ucc_geth: Change uec phy id to the same format as gianfar's
wimax: fix build issue when debugfs is disabled
netxen: fix memory leak in drivers/net/netxen_nic_init.c
tun: Add some missing TUN compat ioctl translations.
ipv4: fix infinite retry loop in IP-Config
net: update documentation ip aliases
net: Fix OOPS in skb_seq_read().
net: Fix frag_list handling in skb_seq_read
netxen: revert jumbo ringsize
ath5k: fix locking in ath5k_config
cfg80211: print correct intersected regulatory domain
cfg80211: Fix sanity check on 5 GHz when processing country IE
iwlwifi: fix kernel oops when ucode DMA memory allocation failure
rtl8187: Fix error in setting OFDM power settings for RTL8187L
mac80211: remove Michael Wu as maintainer
...
This fixes a crash observed when non-existant enable_ms function is
called for jsm driver.
Signed-off-by: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Paul Larson <pl@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit e57db7b (SATA Sil: Blacklist system that spins off disks during ACPI power off)
breaks build like the following, in both cases when CONFIG_DMI set or not.
drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast
sata_sil.c should include dmi.h
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
