Some drivers used on a Marvell Berlin kernel were missing from
multi_v7_defconfig. This series add them:
* The pxa168 Ethernet driver is added as a loadable module.
* The Berlin ADC driver is added as a loadable module.
* Both the Berlin USB PHY and SATA PHY drivers are added,
built-in, as they are required for the already available USB
and SATA functionalities in multi_v7_defconfig.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd screen,
microsd slot, headphones, mini hdmi, mini usb b and power barrel connectors.
It uses a rtl8188cus usb wifi chip and a RDA 5875Y bluetooth chip attached
to uart2. It has a bma250 accelerometer attached to i2c1 addr 0x18, this
only works when ldo3 is set to 2.8 volt, otherwise i2c1 gets stuck, so
for now we mark i2c1 as failed.
It has a pixcir,pixcir_tangoc compatible touchscreen attached to i2c2 addr
0x5c. This is not enabled in this dts, because this variant of the
pixcir_tangoc has separate wakeup and enable pins both of which need
to be driven low before the touchscreen will work. Before we can enable
this the pixcir driver and devicetree-bindings need to be extended to
support these pins.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The cubieboard uses the internal codec to output sound to its mini-jack.
Enable it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CHIP v0.2 has a composite output on a mini-jack connector, the audio
part being provided by the on-SoC codec. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Enable the audio-codec on the Mele A1000 top-set box.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The cubieboard2 uses the internal codec to output sound to its mini-jack.
Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
This commit enables the on-chip audio codec present on the A20 SoC
for the Cubietruck.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Remove the inclusion of linux/mdio-gpio.h in nas4220b, wbd111 and wbd222
boards since mdio-gpio is not used.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* clk-iproc:
clk: iproc: define Broadcom NS2 iProc clock binding
clk: iproc: define Broadcom NSP iProc clock binding
clk: ns2: add clock support for Broadcom Northstar 2 SoC
clk: iproc: Separate status and control variables
clk: iproc: Split off dig_filter
clk: iproc: Add PLL base write function
clk: nsp: add clock support for Broadcom Northstar Plus SoC
clk: iproc: Add PWRCTRL support
clk: cygnus: Convert all macros to all caps
ARM: cygnus: fix link failures when CONFIG_COMMON_CLK_IPROC is disabled
When CONFIG_CYGNUS is set but CONFIG_COMMON_CLK_IPROC is disabled, the
following link failures are caused:
drivers/built-in.o: In function `cygnus_armpll_init':
:(.init.text+0x1d290): undefined reference to `iproc_armpll_setup'
drivers/built-in.o: In function `cygnus_genpll_clk_init':
:(.init.text+0x1d2c4): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_lcpll0_clk_init':
:(.init.text+0x1d304): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_mipipll_clk_init':
:(.init.text+0x1d344): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_asiu_init':
:(.init.text+0x1d370): undefined reference to `iproc_asiu_setup'
It is fixed it by always selecting COMMON_CLK_IPROC from
ARCH_BCM_IPROC, and making COMMON_CLK_IPROC a silent option (thus
preventing it from being erroneously disabled by a user).
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
AM437x-based boards, can use omap4_local_timer_init()
just fine. Let's use that instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The A20 SoC includes the Allwinner audio codec, capable of both 24-bit
playback and capture. This commit adds a device node for it.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A13 and A10s also have the audio codec present. List it in the device
tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A10 SoC includes the Allwinner audio codec, capable of both 24-bit
playback and capture. This commit adds a device node for it.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A20 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). Add it to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A13 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). However, it has a
different divider configuration than the A10, hence the difference
compatible.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A10 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). Add it to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
- A bug where level-triggered interrupts lowered from userspace
are still routed to the guest
- A memory leak an a failed initialization path
- A build error under certain configurations
- Several timer bugs introduced with moving the timer to the active
state handling instead of the masking trick.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEbBAABAgAGBQJWJmf7AAoJEEtpOizt6ddy35UH+NCAt1AInvQajAB1rzXzFSYh
v9PQ5zJ7ZlP8M3HFYjerSl0HrGbi2Cwij5KYE+UAQkXIzCTTdDeB9TUSI/GYQ82M
axel8Ob3deELp03nS5I+gP1NGX3HPDz445grScg7yl1lMs3uDy4viDDM8Vm8+HUX
zZWGpDRHNW3b0myS5NVJvOP7Sm5t7DqklsNScZ04Nut7V8gYEUqEu+ZNKerIZkKn
LrJUVYqqZf33bf6pWle95QZuNQtg84kion3qwWaNl+/8jFkAA8CODyvzar9VMHpf
xA0xUkK1ERZ+hw2n0/BIgCxI4lXvROAx0YpZKnSMgEU5E5p5gGZYqlHCw8r1Rw==
=VQSu
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
A late round of KVM/ARM fixes for v4.3-rc7, fixing:
- A bug where level-triggered interrupts lowered from userspace
are still routed to the guest
- A memory leak an a failed initialization path
- A build error under certain configurations
- Several timer bugs introduced with moving the timer to the active
state handling instead of the masking trick.
Fix wrong compatible for A385 DB AP preventing using suspend
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlYhNEwACgkQCwYYjhRyO9XX9gCgnabcvdHrfFqAD3IFICLCgkOM
U1AAnReiDUjcUhz6oTl6I2+e3PLHY7RO
=BkFw
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.3-2' of git://git.infradead.org/linux-mvebu into fixes
Merge "mvebu fixes for 4.3 (part 2)" from Gregory CLEMENT:
Fix wrong compatible for A385 DB AP preventing using suspend
* tag 'mvebu-fixes-4.3-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: correct a385-db-ap compatible string
- Fix oops with LPAE and moew than 2GB of memory by enabling
ZONE_DMA for LPAE. Probably no need for stable on this one as we
only recently ran into this with the mainline kernel
- Fix imprecise external abort caused by bogus SRAM init. This affects
dm814x recently merged, so no need for stable on this one AFAIK
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWJnm9AAoJEBvUPslcq6VzJHMP/i8DVa6R3OwssmGS3Cp/XKPV
m1GCXReauql0oUfFR0baiVnBKL6x8jEHW91iQeV3b3cUz+8l3jL7Q4yc+voPyjHz
ud890cId4wP54PWtDo4lpzDKi3lQkGBI+zJVAyWLfNPt97xcTh1yXW2HdDQ2Hlf4
nyksDKI1CE42h22l5odB9i0yf7Y/XXl8CYl0ZggHV1XReKSZGveTf8+Qcd1uME2s
ovLoxEOHDsmxwERXxeSw7Vw4MwefCBdXhKZf1a6l++/pyD/HqWNpJqpS+VEX4yaw
9ZGT5wmTZQXzzAx60bfO9kokFaKzKiae1UYZusR1aoEKKvFwh8+7ziTTv5q8Do+s
PRaeczB0tJA9OniwZaZEHNyckMgLlReH3PH5mwYV9DNNnG4LWRDjsx8LWDZ7lcjL
HxvDjbB6Ir51jGCxa4GVH0NZy0NZ+UHFTMv6bgiEc3uO4PMu35syDXfLws4VJWXZ
jC4bR2ShUbrAaGQj8R4aYQFus2MzXu58eqwceDGqeuf9M+wn10IO0/OaAXg5oPhk
TfqB/6+yC8GjyWyRaKV7PrgJKsqcm4S9P2WCuZL+lU5GgnfSrFTb1+OBQl4BQFXD
89Mj/oYOoKQd3qQFmsk2ZKwRqT9kLixKvih0bvkos4saOJipW2aNpLBTwNpQEpRk
N9J0CUyn/p1tQEBVCJj5
=EP6s
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Fixes for omaps for v4.3-rc cycle" from Tony Lindgren:
- Fix oops with LPAE and moew than 2GB of memory by enabling
ZONE_DMA for LPAE. Probably no need for stable on this one as we
only recently ran into this with the mainline kernel
- Fix imprecise external abort caused by bogus SRAM init. This affects
dm814x recently merged, so no need for stable on this one AFAIK
* tag 'omap-for-v4.3/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix imprecise external abort caused by bogus SRAM init
ARM: OMAP2+: Fix oops with LPAE and more than 2GB of memory
Use the AM33XX pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the AM33xx pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the OMAP3 pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am437x-gp-evm, pixcir_i2c_ts can wakeup the system from low power
state via pinctrl and IO daisy chain using generic wakeirq framework.
With commit 3fffd1283927 ("i2c: allow specifying separate wakeup
interrupt in device tree") i2c core allows optional wakeirq to be
specified via device tree. Add wakeup irq entry to enable pixcir_i2c_ts
to wake the system from low power state.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I see that people are still sending emails to my old address (that no
longer exists) since is the one mentioned in the IGEP DTS. Replace it
with my current email address to avoid this.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the current implementation of GPIO hogging and with
gpio-pcf857x is built as module, ethernet doesn't work on boot
and doesn't throw any error/warning to user. Ethernet becomes
operational when inserting gpio-pcf857x module, even this time
there is no error/warning logs to user that ethernet is
operational.
When using with NFS rootfs and gpio-pcf857x as module, board
doesn't boot as it doesn't get any ip address and doesn't throw
any error/warning. To over come this, now cpsw driver tries to
get mode-gpios. When gpio-pcf857x is built as module it will
throw error, so that user can decide either to built in
gpio-pcf857x to continue with nfs boot or choose alternate rootfs
filesystem like sd/ramdisk.
When using mmc/ramdisk as root fs, cpsw will probe defer and
re-probes again when gpio-pcf857x module is inserted and ethernet
becomes operational.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The vgic code on ARM is built for all configurations that enable KVM,
but the parent_data field that it references is only present when
CONFIG_IRQ_DOMAIN_HIERARCHY is set:
virt/kvm/arm/vgic.c: In function 'kvm_vgic_map_phys_irq':
virt/kvm/arm/vgic.c:1781:13: error: 'struct irq_data' has no member named 'parent_data'
This flag is implied by the GIC driver, and indeed the VGIC code only
makes sense if a GIC is present. This changes the CONFIG_KVM symbol
to always select GIC, which avoids the issue.
Fixes: 662d9715840 ("arm/arm64: KVM: Kill CONFIG_KVM_ARM_{VGIC,TIMER}")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Jump to correct label and free kvm_host_cpu_state
Reviewed-by: Wei Huang <wei@redhat.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable some options that have recently been enabled on Tegra platforms:
* TOUCHSCREEN_WM97XX: touchscreen support on Toradex Colibri
* SND_SOC_TEGRA_WM9712: audio support on Toradex Colibri
Signed-off-by: Thierry Reding <treding@nvidia.com>
The indentation for properties in the SATA device tree node on Tegra124
deviates from the rest of the device tree file. Restore consistency and
get rid of a couple of gratuitous blank lines while at it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now that the core code supports acquire/release/relaxed versions of
the atomic_inc family, implement only the _relaxed flavours in the ARM
backend so that we get all of the others for free.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1444227038-12533-1-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ELM address information is provided by device tree. No longer need
to include this information within hwmod.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[paul@pwsan.com: fixed chip names in subject line; dropped the OMAP4 section
since the OMAP4 SoC DTS file doesn't have the ELM address space documented
yet]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit b483a4a5a711 ("ARM: OMAP4+: hwmod data: Don't prevent RESET of
USB Host module") added the SYSC_HAS_RESET_STATUS flag to both OMAP4
and OMAP5 USB host module hwmon sysconfig but that flag was already
set for OMAP5. So now the flag appears twice in the expression.
make coccicheck complains with the following message:
omap_hwmod_54xx_data.c:1846:37-58: duplicated argument to & or |
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
fncpy() requires that the source and the destination are both 8-byte
aligned.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: d94e688cae56 ("ARM: at91/pm: move the copying the sram function to the sram initialization phase")
Cc: <stable@vger.kernel.org> # 4.1+
The AT91 SDHCI device has been introduced with Atmel SAMA5D2 SoC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Flexcom device has been introduced with Atmel SAMA5D2 SoC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The OTG arrangement on the LinkSprite pcDuino v3 Nano is the same as the
pcDuino 1/2/3: the OTG port's 5V line is connected directly to the 5V
bus (it's not switchable), and the OTG port's ID pin is connected to PH4
on the A20.
Tested successfully in both host and device modes.
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull networking fixes from David Miller:
1) Account for extra headroom in ath9k driver, from Felix Fietkau.
2) Fix OOPS in pppoe driver due to incorrect socket state transition,
from Guillaume Nault.
3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.
4) Power management fixes for iwlwifi, from Johannes Berg.
5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.
6) Fix dst_entry usage in ARP replies, from Jiri Benc.
7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.
8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.
9) Various resource allocation/freeing cures in DSA< from Neil
Armstrong.
10) A series of bug fixes in the openvswitch conntrack support, from
Joe Stringer.
11) Fix two cases (BPF and act_mirred) where we have to clean the sender
cpu stored in the SKB before transmitting. From WANG Cong and
Alexei Starovoitov.
12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
Achiad Shochat.
13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
configuration via ethtool. From Yuval Mintz.
14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
'dev' is NULL, from Eric Biederman.
15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.
16) kcalloc() gstrings ethtool buffer before having driver fill it in,
in order to prevent kernel memory leaking. From Joe Perches.
17) Fix mixxing rt6_info initialization for blackhole routes, from
Martin KaFai Lau.
18) Kill VLAN regression in via-rhine, from Andrej Ota.
19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.
20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.
21) Scrube SKBs when pushing them between namespaces in openvswitch,
from Joe Stringer.
22) bcmgenet enables link interrupts too early, fix from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
net: bcmgenet: Fix early link interrupt enabling
tunnels: Don't require remote endpoint or ID during creation.
openvswitch: Scrub skb between namespaces
xen-netback: correctly check failed allocation
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
netlink: Trim skb to alloc size to avoid MSG_TRUNC
net: add pfmemalloc check in sk_add_backlog()
via-rhine: fix VLAN receive handling regression.
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Bluetooth: Fix initializing conn_params in scan phase
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
Bluetooth: Fix remove_device behavior for explicit connects
Bluetooth: Fix LE reconnection logic
Bluetooth: Fix reference counting for LE-scan based connections
Bluetooth: Fix double scan updates
mlxsw: core: Fix race condition in __mlxsw_emad_transmit
tipc: move fragment importance field to new header position
ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
tipc: eliminate risk of stalled link synchronization
...
