* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
This includes PXA work up to the SPI changes for the initial merge,
since e172274ccc depends on the SPI
tree being merged.
Conflicts:
arch/arm/configs/em_x270_defconfig
arch/arm/configs/xm_x270_defconfig
This reverts commit e872154921.
Andrey Borzenkov reports that it resulted in a totally hung machine for
him when loading the OHCI driver. Extensive netconsole capture with
SysRq output shows that modprobe gets stuck in ohci_hub_status_data()
when probing and enabling the OHCI controller, see for example
http://lkml.org/lkml/2008/7/5/236
for an analysis.
The problem appears to be an interrupt flood triggered by the commit
that gets reverted, and Andrey confirmed that the revert makes things
work for him again.
Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a problem with OHCI where canceling bulk or
interrupt URBs may lose track of the right data toggle. This
seems to be a longstanding bug, possibly dating back to the
Linux 2.4 kernel, which stayed hidden because
(a) about half the time the data toggle bit was correct;
(b) canceling such URBs is unusual; and
(c) the few drivers which cancel these URBs either
[1] do it only as part of shutting down, or
[2] have fault recovery logic, which recovers.
For those transfer types, the toggle is normally written back
into the ED when each TD is retired. But canceling bypasses
the mechanism used to retire TDs ... so on average, half the
time the toggle bit will be invalid after cancelation.
The fix is simple: the toggle state of any canceled TDs are
propagated back to the ED in the finish_unlinks function.
(Issue found by leonidv11@gmail.com ...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a regression in the EHCI driver's TIMER_IO_WATCHDOG
behavior. The patch "USB: EHCI: add separate IAA watchdog timer" changed
how that timer is handled, so that short timeouts on the remaining
timer (unfortunately, overloaded) would never be used.
This takes a more direct approach, reorganizing the code slightly to
be explicit about only the I/O watchdog role now being overridable.
It also replaces a now-obsolete comment describing older timer behavior.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the SM501 and another platform driver, such as the SM501
then we end up defining PLATFORM_DRIVER twice. This patch
seperated the SM501 onto a seperate define of SM501_OHCI_DRIVER
so that it can be selected without overwriting the original
definition.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change omap USB code to use omap_read/write instead of __REG for multi-omap
Cc: David Brownell <david-b@pacbell.net>
Cc: linux-usb@vger.kernel.org
Cc: i2c@lm-sensors.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
and include pxa2xx-regs.h as build fix since PSSR definitions
moved from pxa-regs.h into pxa2xx-regs.h.
Note: This change is temporary as pxa27x processor specific
code will be finally moved elsewhere (both drivers should
support pxa3xx, too).
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes the bogus "io mem 0x00000000" message printed
during driver init due to hcd->rsrc_start being assigned after
the call to usb_add_hcd().
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
R8A66597 is similar to SH7723 USB 2.0 Host/Function module.
In addition, the USB of SH7366 is compatible with SH7723.
It can support SH7723 USB host by changing Kconfig.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit fa38dfcc56.
It wasn't really a regression and David and Alan are still working
through the issues reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1099) fixes a performance regression in ehci-hcd. The
fundamental problem is that queue headers get removed from the
schedule too quickly, since the code checks for a counter advancing
rather than making an actual time-based check. The latency involved
in removing the queue header and then relinking it can severely
degrade certain kinds of workloads.
The patch replaces a simple counter with a timestamp derived from the
controller's uframe value. In addition, the delay for unlinking an
idle queue header is increased from 5 ms to 10 ms; since some
controllers (nVidia) have a latency of up to 1 ms for unlinking, this
reduces the relative impact from 20% to 10%.
Finally, a logical error left over from the IAA watchdog-timer
conversion is corrected. Now the driver will always either unlink an
idle queue header or set up a timer to unlink it later. The old code
would sometimes fail to do either.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Leonid <leonidv11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1098) changes the way ehci-hcd schedules its periodic
Iso transfers. That the current scheduling code is wrong is clear on
the face of it: Sometimes it returns -EL2NSYNC (meaning that an URB
couldn't be scheduled because it was submitted too late), but it does
this even when the URB_ISO_ASAP flag is set (meaning the URB should be
scheduled as soon as possible).
The new code properly implements as-soon-as-possible scheduling,
assigning the next unexpired slot as the URB's starting point. It
also is more careful about checking for Iso URB completion: It doesn't
bother to check for activity during frames that are already over,
and it allows for the possibility that some of the URB's packets may
have raced the hardware when they were submitted and so never got used
(the packet status is set to -EXDEV).
This fixes problems several people have experienced with USB video
applications.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1097) fixes a bug in the remote-wakeup handling in
ehci-hcd. The driver currently does not keep track of whether the
change-suspend feature is enabled for each port; the feature is
automatically reset the first time it is read. But recent changes to
the hub driver require that the feature be read at least twice in
order to work properly.
A bit-vector is added for storing the change-suspend feature values.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller. But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.
The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller. If it has, the
error message is suppressed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1095) cleans up the HCD glue and several of the EHCI
bus-glue files. The ehci->is_tdi_rh_tt flag is redundant, since it
means the same thing as the hcd->has_tt flag, so it is removed and the
other flag used in its place.
Some of the bus-glue files didn't get the relinquish_port method added
to their hc_driver structures. Although that routine currently
doesn't do anything for controllers with an integrated TT, in the
future it might. So the patch adds it where it is missing.
Lastly, some of the bus-glue files have erroneous entries for their
hc_driver's suspend and resume methods. These method pointers are
specific to PCI and shouldn't be used otherwise.
(The patch also includes an invisible whitespace fix.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Commit 7329e211b9 ("USB: root hubs don't
lie about their number of TTs") requires the various platform EHCI
glue modules to set ->has_tt if the root hub has a Transaction
Translator.
The Orion EHCI root hub does have a Transaction Translator, so set
->has_tt in ehci_orion_setup(). This fixes oopsing on plugging in a
low speed device.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/isp1760-if.c:275: warning: 'ret' is used uninitialized in this function
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/ohci-sm501.c:93:24: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3254:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3267:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3277:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3285:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3293:9: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix printk format warnings in isp1760 (in linux-next):
next-20080430/drivers/usb/host/isp1760-hcd.c:994: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
next-20080430/drivers/usb/host/isp1760-hcd.c:1092: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sparc doesn't have some of the OF interfaces this driver
wants to use.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1084b) fixes the way uhci-hcd handles polling and
remote wakeups for its root hubs. When remote wakeup is disabled,
neither interrupts nor polling should be enabled during a root-hub
suspend. Likewise, if interrupts are enabled during suspend then
polling isn't needed.
Furthermore the EGSM (Enter Global Suspend Mode) bit shouldn't be set
in the Command register unless remote wakeup is enabled. Apparently
some controllers will issue a remote-wakeup interrupt whenever EGSM
is on, even if Resume-Detect interrupts are supposedly disabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch (as1086) works around a bogus "uninitialized variable"
warning generated by some versions of GCC.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds HCD support for the Cypress c67x00 family of devices.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver has been written from scratch and supports the ISP1760. ISP1761
might (should) work as well but the OTG isn't supported. Also ISO packets are
not. However, it works on my little PowerPC board.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* endianness annotations
* endianness fixes
* missing get_unaligned/put_unaligned
It's pretty much all over the place, changes to different files are independent.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Serial-parts-Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1072) fixes some recently-introduced compile problems
that show up in ehci-hcd when CONFIG_PM is turned off.
PORT_WAKE_BITS needs to be defined always.
ehci_port_power() is called during initialization by all the
EHCI variants other than the PCI version, in which it is
"defined but not used". So add a call to it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simplify processing of completed qtds, and correct handling of short
reads, by removing two state variables:
- "qtd_status" wasn't needed. The current URB's status is either
OK (-EINPROGRESS) or some fault status. Once a fault appears,
the queue halts and any later QTDs are immediately removed, so
no temporary status is needed. (Or for typical short reads,
it's not treated as a fault, so no queue halt is needed.)
- "do_status" was erroneous. Because of how the queue is set up,
short control reads can (and should!) be treated like full size
reads, and cleaned up the usual way. The status stage will be
executed transparently, and usbcore handles the choice of whether
to report this status as unexected.
The "do_status" problem caused a rather perplexing timing-dependent
problem with usbtest case 10. Sometimes it would make the controller
skip a dozen transactions while (wrongly) trying to clean up after a
short transfer. Fortunately, removing a dcache contention issue made
this become trivial to reproduce (on one test rig), so enough clues
finally presented themselves ... I think this has been around for a
very long time, but was worsened by recent urb->status changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1069b) changes the way OHCI root-hub status-change
interrupts are enabled. Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub. This approach turns out to be subject to races, resulting
in unnecessary polling.
The patch does away with the method entirely. Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present. This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1068b) disables the RD interrupt flag when an OHCI root
hub is suspended with remote wakeup disabled. Although the spec
clearly states that this flag permits the controller to issue an
interrupt when a resume request from downstream is detected and not
when a local status change occurs, some controllers mistakenly use it
for both types of event.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is suspended, whether or not it is enabled for
remote wakeup depends on the device_may_wakeup() setting. The setting
is then saved in the do_remote_wakeup flag.
Later on, however, the device_may_wakeup() value can change because of
user activity. So when testing whether a suspended device is or
should be enabled for remote wakeup, we should always test
do_remote_wakeup instead of device_may_wakeup(). This patch (as1076)
makes that change for root hubs in several places.
The patch also adjusts uhci-hcd so that when an autostopped controller
is suspended, the remote wakeup setting agrees with the value recorded
in the root hub's do_remote_wakeup flag.
And the patch adjusts ehci-hcd so that wakeup events on selectively
suspended ports (i.e., the bus itself isn't suspended) don't turn on
the PME# wakeup signal.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Provide better comments about qh_completions() and QTD handling.
That code can be *VERY* confusing, since it's evolved over a few
years to cope with both hardware races and silicon quirks.
Remove two unlikely() annotations that match the GCC defaults
(and are thus pointless); add an "else" to highlight code flow.
This patch doesn't change driver behavior.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
R8A66597 is similar to SH7366 USB 2.0 Host/Function module. It can
support SH7366 USB host by changing several R8A66597 code.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the problem that enumeration of a USB device was slow.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver ignored the value of bInterval and revised the problem
that performed interrupt transfer.
ASIX USB Ethernet adapter comes to work with this host controller
by applying this patch.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch refactors some shutdown code so it can be shared between
ehci_stop() and ehci_shutdown().
This also fixes a couple potential bugs:
- ehci_shutdown() was not locking ehci->lock before halting the HC.
- ehci_shutdown() didn't disable the watchdog and IAA timers.
- ehci_stop() was resetting the host controller when it may have been
running, which the EHCI spec says "may result in undefined behavior".
ehci_stop() was calling port_power() to turn off the ports, which waited
20ms after applying the port change. The msleep was for the case where
the HC might take 20ms to turn the ports on; since we're shutting them
off, we can avoid the msleep and just use ehci_turn_off_ports().
ehci_stop() doesn't need to clear the intr_enable register or revert
ownership of the companion controllers to the BIOS, because the host
controller reset should have done that. There might be a buggy host
controller that doesn't follow the reset rules, but for now we assume
it's redundant code and remove it.
[ A subsequent patch will cancel the timers later ... this version
carries forward existing bugs where timers could get re-armed
after they're canceled. ]
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers in the ohci-hcd family should perform certain tasks whenever
their controller device is resumed. These include checking for loss
of power during suspend, turning on port power, and enabling interrupt
requests.
Until now these jobs have been carried out when the root hub is
resumed, not when the controller is. Many drivers work around the
resulting awkwardness by automatically resuming their root hub
whenever the controller is resumed. But this is wasteful and
unnecessary.
To simplify the situation, this patch (as1066) adds a new core
routine, ohci_finish_controller_resume(), which can be used by all the
OHCI-variant drivers. They can call the new routine instead of
resuming their root hubs. And ohci-pci.c can call it instead of using
its own special-purpose handler.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The .suspend and .resume method pointers in struct usb_hcd have not
been fully understood by host-controller driver writers. They are
meant for use with PCI controllers; other platform-specific drivers
generally should not refer to them.
To try and clarify matters, this patch (as1065) renames those methods
to .pci_suspend and .pci_resume. It eliminates corresponding dead code
and bogus references in the ohci-ssb and u132-hcd drivers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently EHCI root hubs enumerate with a bDeviceProtocol code
indicating that they possess a Transaction Translator. However the
vast majority of controllers do not; they rely on a companion
controller to handle full- and low-speed communications. This patch
(as1064) changes the root-hub device descriptor to match the actual
situation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1063) fixes a bug in the way ohci-hcd resumes its
controllers. It leaves the Master Interrupt Enable bit turned off.
If the root hub is resumed immediately this won't matter. But if the
root hub is suspended (say because no devices are plugged in), it won't
ever wake up by itself.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
platform_get_resource() may return null, so although it seems it will never
do so here unless there's a bug elsewhere, it does no harm to be defensive
and test.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was converting a semaphore in this file to a mutex when I noticed that
this file has some fairly rampant style problems. Practically every line
has spaces instead of tabs .. Once I cleared that up, checkpatch.pl showed
a number of other problem.. I think this file might be a good one to review
for new style checks that could be added..
Below are the only two remaining which I didn't remove.
#5083: FILE: drivers/usb/host/u132-hcd.c:2907:
+ error:
WARNING: labels should not be indented
#5087: FILE: drivers/usb/host/u132-hcd.c:2911:
+ stall:
These labels are actually inside a switch statement, and they are right
under "default:". "default:" appears to be exempt and these other label
should be too, or default shouldn't be exempt.
I also deleted a few lines due to single statements inside { } ,
if (is_error()) {
return;
}
becomes,
if (is_error())
return;
with one line deleted.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to David Brownell, this feature doesn't require an
experimental designation any longer.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
