As we progress with DB5500 and future voltage domain regulators
based on very similar hardware as found in the DB8500 PRCMU,
it makes sense to split off the generic parts and introduce
some generic debug code for the DBx500 regulators. This patch
accoplish a basic abstraction of the DBx500 voltage domain
regulators.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MODULE_DEVICE_TABLE will setup the modalias, thus adding
a MODULE_ALIAS for an entry already in s5m8767_pmic_id is redundant.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
S5M8767A is a cost-effective PMIC which is designed for mobile applications.
It includes high efficient 9 Buck converters, 28 LDOs.
Especially, S5M8767A is optimized for Multi-core SOCs.
And during DVFS operation, S5M8767A output stable voltage.
This patch implement regulator driver for S5M8767A.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regulator module consists of 1 DCDC. The output voltage
is configurable and is meant for supply power to the core
voltage of Soc.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix fixed regulator using DT failed to call regulator_register.
of_get_regulator_init_data set apply_uV to 1, but fixed regulator
doesn't need it. Set it back to 0.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Max8925 ldo status should be determined by two factors:
1. power up/down sequence selection(LDOCTL[4:2]).
2. i2c enable bit(LDOCTL[0]).
Max8925 ldo support two types of power up/down sequence:
1. flexible sequence(LDOCTL[4:2] = 0~6).
2. i2c sequence(LDOCTL[4:2] = 7).
With flexible sequence selected, the ldo is enabled during power up by default.
With i2c sequence selected, the ldo is controlled by the i2c enable bit(LDOCTL[0]).
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch allows consumers to forcibly disable multiple regulator
clients in a single API call.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_get needs of_node to find right regulator.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
During regulator_register, the rail is set on the provided
machine constraints and if it is enabled then it is also
require to enable the supply regulator. This will make sure
that:
1. Proper reference count for supply regulator to be maintain.
2. Supply regulator should be enable when given rail is enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert mc13892-regulator driver to use devm_kzalloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert mc13783-regulator driver to use devm_kzalloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the case of create_regulator() fails, goto the error path immediately.
It does not make sense to update rdev->open_count if create_regulator fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It adds device tree probe support for mc13892-regulator driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's not really necessary to add a prefix 'MC13892__' for each mc13892
regulator name, since the chip must have been identified as mc13892
when we look at the regulator name.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
da9052_regulator_info and da9053_regulator_info are not used outside
this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Dialog PMIC has below featured regulators:-
DA9052-BC - 4 DVS Buck converters 0.5V - 3.6V upto 1Amp.
DA9053-AA/BX - 4 DVS Buck converters 0.5V - 2.5V upto 3Amp.
DA9052/53 - 10 Programmable LDO's High PSSR, 1% accuracy.
This patch support all the DA9052 and Da9053 regulators. The output voltages are
fully programmable via I2C or SPI interface. The platform data with regulation
constraints is passed down from the board to the regulator.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's not always true that the device_node of regulator can be found
at dev->of_node at the time when of_get_regulator_init_data() is being
called, because in some cases the regulator nodes in device tree do
not have 'struct device' behind them until regulator_dev gets created
for it by core function regulator_register().
The patch adds device_node as a new parameter to
of_get_regulator_init_data(), so that caller can pass in the node of
regulator directly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise there is no way in the bindings to configure a fixed voltage
via software. It seems reasonable to assume that if the binding explicitly
specifies a voltage we want to actually use that voltage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows read-only access to the device configuration which may be
useful for diagnostics.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
SMPS regulator voltage control differs from the one of the LDO ones.
Current TWL code was using LDO regulator ops for controlling the SMPS
regulators, which fails. This was fixed fixed by adding separate
regulator type which uses correct logic and calculations for the
voltage levels.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This is caused by dereferencing 'rdev' after device_unregister() in
the regulator_unregister() function. 'rdev' is freed by
device_unregister(), so it must not be dereferenced after this call.
[Edited commit message for legibility -- broonie]
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch converts virtual and userspace regulator consumer drivers to use the
module_platform_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The implementation in aat2870_update() already did the bitwise and operation
against mask parameter.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In current implementation, the pointer ri is not NULL if no id is matched.
Fix it by checking i == ARRAY_SIZE(aat2870_regulators) if no id is matched.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
of_get_fixed_voltage_config() may return NULL, return -ENOMEM in this case
so we don't dereference NULL pointer.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_get_regulator_init_data() may return NULL, thus
check the return value to avoid NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_get_regulator_init_data is called in drivers/regulator/fixed.c
which could be a module.
Export of_get_regulator_init_data to fix below build error:
ERROR: "of_get_regulator_init_data" [drivers/regulator/fixed.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit 2c043bcbf2 ("regulator: pass additional of_node to
regulator_register()") caused a compile break because it missed
updating the regulator_register() call in gpio-regulator.c with
the additional parameter (NULL).
The compile break as reported by Stephen Rothwell with the
x86_64 allmodconfig looked like this
drivers/regulator/gpio-regulator.c: In function 'gpio_regulator_probe':
drivers/regulator/gpio-regulator.c:287:8: error: too few arguments to function 'regulator_register'
include/linux/regulator/driver.h:215:23: note: declared here
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Device nodes in DT can associate themselves with one or more
regulators/supply by providing a list of phandles (to regulator nodes)
and corresponding supply names.
For Example:
devicenode: node@0x0 {
...
...
vmmc-supply = <®ulator1>;
vpll-supply = <®ulator2>;
};
The driver would then do a regulator_get(dev, "vmmc"); to get
regulator1 and do a regulator_get(dev, "vpll"); to get
regulator2.
of_get_regulator() extracts the regulator node for a given
device, based on the supply name.
Use it to look up the regulator for a given consumer from device tree, during
a regulator_get(). If not found fallback and lookup through
the regulator_map_list instead.
Also, since the regulator dt nodes can use the same binding to
associate with a parent regulator/supply, allow the drivers to
specify a supply_name, which can then be used to lookup dt
to find the parent phandle.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With device tree support for regulators, its needed that the
regulator_dev->dev device has the right of_node attached.
To be able to do this add an additional parameter to the
regulator_register() api, wherein the dt-adapted driver can
then pass this additional info onto the regulator core.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The fixed regulator driver uses of_get_fixed_voltage_config()
to extract fixed_voltage_config structure contents from device tree.
Also add documenation for additional bindings for fixed
regulators that can be passed through dt.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The helper routine is meant to be used by the regulator drivers
to extract the regulator_init_data structure from the data
that is passed from device tree.
'consumer_supplies' which is part of regulator_init_data is not extracted
as the regulator consumer mappings are passed through DT differently,
implemented in subsequent patches.
Similarly the regulator<-->parent/supply mapping is handled in
subsequent patches.
Also add documentation for regulator bindings to be used to pass
regulator_init_data struct information from device tree.
Some of the regulator properties which are linux and board specific,
are left out since its not clear if they can
be in someway embedded into the kernel or passed in from DT.
They will be revisited later.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
