No alias checking needed for setting present/not-present mapping. Otherwise,
we may need to break large pages for 64-bit kernel text mappings (this adds to
complexity if we want to do this from atomic context especially, for ex:
with CONFIG_DEBUG_PAGEALLOC). Let's keep it simple!
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: arjan@linux.intel.com
Cc: venkatesh.pallipadi@intel.com
Cc: jeremy@goop.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Don't use large pages for kernel identity mapping with DEBUG_PAGEALLOC.
This will remove the need to split the large page for the
allocated kernel page in the interrupt context.
This will simplify cpa code(as we don't do the split any more from the
interrupt context). cpa code simplication in the subsequent patches.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: arjan@linux.intel.com
Cc: venkatesh.pallipadi@intel.com
Cc: jeremy@goop.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the first pass, kernel physical mapping will be setup using large or
small pages but uses the same PTE attributes as that of the early
PTE attributes setup by early boot code in head_[32|64].S
After flushing TLB's, we go through the second pass, which setups the
direct mapped PTE's with the appropriate attributes (like NX, GLOBAL etc)
which are runtime detectable.
This two pass mechanism conforms to the TLB app note which says:
"Software should not write to a paging-structure entry in a way that would
change, for any linear address, both the page size and either the page frame
or attributes."
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: arjan@linux.intel.com
Cc: venkatesh.pallipadi@intel.com
Cc: jeremy@goop.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Export set_memory_ro() and set_memory_rw() calls for use by drivers that need
to have more debug information about who might be writing to memory space.
this was initially developed for use while debugging a memory corruption
problem with e1000e.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Go through the iomem resource tree to check if any of the ioremap()
requests span more than any slot in the iomem resource tree and do
a WARN_ON() if we hit this check.
This will raise a red-flag, if some driver is mapping more than what
is needed. And hopefully identify possible corruptions much earlier.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
They were already called once in arch/x86/kernel/setup.c - we don't need to call them again.
fixes:
http://bugzilla.kernel.org/show_bug.cgi?id=11485
Signed-off-by: Alex Nixon <alex.nixon@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Perodically check for corruption in low phusical memory. Don't bother
checking at fault time, since it won't show anything useful.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some BIOSes have been observed to corrupt memory in the low 64k. This
change:
- Reserves all memory which does not have to be in that area, to
prevent it from being used as general memory by the kernel. Things
like the SMP trampoline are still in the memory, however.
- Clears the reserved memory so we can observe changes to it.
- Adds a function check_for_bios_corruption() which checks and reports on
memory becoming unexpectedly non-zero. Currently it's called in the
x86 fault handler, and the powermanagement debug output.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since the fourth PDPT entry cannot be shared under Xen,
vmalloc_sync_all() must iterate over pmd-s rather than pgd-s here.
Luckily, the code isn't used for native PAE (SHARED_KERNEL_PMD is 1)
and the change is benign to non-PAE.
Also do a little more cleanup in that function.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
They were already called once in arch/x86/kernel/setup.c - we don't need to call them again.
Signed-off-by: Alex Nixon <alex.nixon@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The CPA test code uses _PAGE_UNUSED1, so make sure its obvious.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the start addr for free_memtype calls in the error path.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
early_io{re,un}map() are __init and hence can't be called from __meminit
functions.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While I don't have a hotplug capable system at hand, I think two issues need
fixing:
- pud_phys (in kernel_physical_ampping_init()) would remain uninitialized in
the after_bootmem case
- the locking done just around phys_pmd_{init,update}() would leave out pgd
updates, and it was needlessly covering code portions that do allocations
(perhaps using a more friendly gfp value in alloc_low_page() would then be
possible)
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Actually, might as well simply reconstruct the memtype list at free time
I guess. How is this for a coalescing version of the array functions?
Compiles, boots and provides me with:
root@7ixe4:~# wc -l /debug/x86/pat_memtype_list
53 /debug/x86/pat_memtype_list
otherwise (down from 16384+).
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The new set_memory_array_{uc,wb}() pass virtual addresses to
{reserve,free}_memtype() it seems.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We changed the interface of some pageattr, this patch makes
pageattr-test compile.
Signed-off-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add array interface APIs of pageattr. page based cache flush is quite
slow for a lot of pages. If pages are more than 1024 (4M), the patch
will use a wbinvd(). We have a simple test here (run a 3d game - open
arena), nearly all agp memory allocation are small (< 1M), so suppose
this will not impact runtime performance.
Signed-off-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All kernel mappings like ioremap(), etc uses UC_MINUS as the type. /dev/mem
mappings with /dev/mem being opened with O_SYNC however was using UC,
resulting in a conflict with /dev/mem mmap failing. This seems to be
affecting some apps (one being flashrom) which are using O_SYNC and which were
working before.
Switch /dev/mem with O_SYNC also to UC_MINUS.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Big thinko in pat memtype tracking code. reserve_memtype should be called
with physical address and not virtual address.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
WARNING: vmlinux.o(.text+0x180af): Section mismatch in reference from the function leave_uniprocessor() to the function .cpuinit.text:cpu_up()
The function leave_uniprocessor() references
the function __cpuinit cpu_up().
This is often because leave_uniprocessor lacks a __cpuinit
annotation or the annotation of cpu_up is wrong.
leave_uniprocessor calls cpu_up only when CONFIG_HOTPLUG_CPU is set,
so it can be safely annotated as __ref
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pekka Paalanen <pq@iki.fi>
Booting kernel with vmalloc=[any size<=16m] will oops on my pc (i386/1G memory).
BUG_ON in arch/x86/mm/init_32.c triggered:
BUG_ON((unsigned long)high_memory > VMALLOC_START);
It's due to the vm area hole.
In include/asm-x86/pgtable_32.h:
#define VMALLOC_OFFSET (8 * 1024 * 1024)
#define VMALLOC_START (((unsigned long)high_memory + 2 * VMALLOC_OFFSET - 1) \
& ~(VMALLOC_OFFSET - 1))
There's several related point:
1. MAXMEM :
(-__PAGE_OFFSET - __VMALLOC_RESERVE).
The space after VMALLOC_END is included as well, I set it to
(VMALLOC_END - PAGE_OFFSET - __VMALLOC_RESERVE)
2. VMALLOC_OFFSET is not considered in __VMALLOC_RESERVE
fixed by adding VMALLOC_OFFSET to it.
3. VMALLOC_START :
(((unsigned long)high_memory + 2 * VMALLOC_OFFSET - 1) & ~(VMALLOC_OFFSET - 1))
So it's not always 8M, bigger than 8M possible.
I set it to ((unsigned long)high_memory + VMALLOC_OFFSET)
4. the VMALLOC_RESERVE is an unused macro, so remove it here.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Cc: akpm@linux-foundation.org
Cc: hidave.darkstar@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Use WARN() instead of a printk+WARN_ON() pair; this way the message
becomes part of the warning section for better reporting/collection.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: akpm@linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rene Herman reported significant Xorg startup/shutdown slowdown due
to PAT. It turns out that the memtype list has thousands of entries.
Add cached_entry to list add routine, in order to speed up the
lookup for sequential reserve_memtype calls.
Reported-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: add MAP_STACK mmap flag
x86: fix section mismatch warning - spp_getpage()
x86: change init_gdt to update the gdt via write_gdt, rather than a direct write.
x86-64: fix overlap of modules and fixmap areas
x86, geode-mfgpt: check IRQ before using MFGPT as clocksource
x86, acpi: cleanup, temp_stack is used only when CONFIG_SMP is set
x86: fix spin_is_contended()
x86, nmi: clean UP NMI watchdog failure message
x86, NMI: fix watchdog failure message
x86: fix /proc/meminfo DirectMap
x86: fix readb() et al compile error with gcc-3.2.3
arch/x86/Kconfig: clean up, experimental adjustement
x86: invalidate caches before going into suspend
x86, perfctr: don't use CCCR_OVF_PMI1 on Pentium 4Ds
x86, AMD IOMMU: initialize dma_ops after sysfs registration
x86m AMD IOMMU: cleanup: replace LOW_U32 macro with generic lower_32_bits
x86, AMD IOMMU: initialize device table properly
x86, AMD IOMMU: use status bit instead of memory write-back for completion wait
x86: silence mmconfig printk
x86, msr: fix NULL pointer deref due to msr_open on nonexistent CPUs
...
WARNING: vmlinux.o(.text+0x17a3e): Section mismatch in reference from the function set_pte_vaddr_pud() to the function .init.text:spp_getpage()
The function set_pte_vaddr_pud() references
the function __init spp_getpage().
This is often because set_pte_vaddr_pud lacks a __init
annotation or the annotation of spp_getpage is wrong.
spp_getpage is called from __init (__init_extra_mapping) and
non __init (set_pte_vaddr_pud) functions, so it can't be __init.
Unfortunately it calls alloc_bootmem_pages which is __init,
but does it only when bootmem allocator is available (after_bootmem == 0).
So annotate it accordingly.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Jean Delvare's machine triggered this BUG
acpi_os_map_memory phys ffff0000 size 65535
------------[ cut here ]------------
kernel BUG at arch/x86/mm/pat.c:233!
with ACPI in the backtrace.
Adding some debugging output showed that ACPI calls
acpi_os_map_memory phys ffff0000 size 65535
And ioremap/PAT does this check in 32bit, so addr+size wraps and the BUG
in reserve_memtype() triggers incorrectly.
BUG_ON(start >= end); /* end is exclusive */
But reserve_memtype already uses u64:
int reserve_memtype(u64 start, u64 end,
so the 32bit truncation must happen in the caller. Presumably in ioremap
when it passes this information to reserve_memtype().
This patch does this computation in 64bit.
http://bugzilla.kernel.org/show_bug.cgi?id=11346
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Highmem code can leave ptes and tlb entries around for a given page even after
kunmap, and after it has been freed.
>From what I can gather, the PAT code may change the cache attributes of
arbitrary physical addresses (ie. including highmem pages), which would result
in aliases in the case that it operates on one of these lazy tlb highmem
pages.
Flushing kmaps should solve the problem.
I've also just added code for conditional flushing if we haven't got
any dangling highmem aliases -- this should help performance if we
change page attributes frequently or systems that aren't using much
highmem pages (eg. if < 4G RAM). Should be turned into 2 patches, but
just for RFC...
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce two APIs for page attribute. flushing tlb/cache in every page
attribute is expensive. AGP gart usually will do a lot of operations to
change a page to uc, new APIs can reduce flush.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: airlied@linux.ie
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Do we actually want these DirectMap lines in the x86 /proc/meminfo?
I can see they're interesting to CPA developers and TLB optimizers,
but they don't fit its usual "where has all my memory gone?" usage.
If they are to stay, here are some fixes.
1. On x86_32 without PAE, they're not 2M but 4M pages: no need to
mess with the internal enum, but show the right name to users.
2. Many machines can never show anything but 0 for DirectMap1G,
so suppress that line unless direct_gbpages are really enabled.
3. The unit in /proc/meminfo is kB not number of pages: HugePages
messed that up, but they're an example to regret not to follow.
4. Once we use kB, it's easy to see that 1GB has gone missing (which
explains why CONFIG_CPA_DEBUG=y soon wraps DirectMap2M negative):
because head_64.S's level2_ident_pgt entries were not counted.
My fix is not ideal, but works for more and for less than 1G,
and avoids interfering with early bootup pagetable contortions.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so we don't get warning on 32bit system with 64g RAM or more
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use WARN() instead of a printk+WARN_ON() pair; this way the message becomes
part of the warning section for better reporting/collection.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
fix spinlock recursion in hvc_console
stop_machine: remove unused variable
modules: extend initcall_debug functionality to the module loader
export virtio_rng.h
lguest: use get_user_pages_fast() instead of get_user_pages()
mm: Make generic weak get_user_pages_fast and EXPORT_GPL it
lguest: don't set MAC address for guest unless specified
Out of line get_user_pages_fast fallback implementation, make it a weak
symbol, get rid of CONFIG_HAVE_GET_USER_PAGES_FAST.
Export the symbol to modules so lguest can use it.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Recently I've run a kernel w/o PAT support and wondered why there was
a file "x86/pat_memtype_list" in debugfs. Of course it's empty if PAT
is disabled ... so just get rid of this interface if PAT is disabled.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simon Horman reported that gcc-3.4.x crashes when compiling
pgd_prepopulate_pmd() when PREALLOCATED_PMDS == 0 and CONFIG_DEBUG_INFO
is enabled.
Adding an extra check for PREALLOCATED_PMDS == 0 [which is compiled out
by gcc] seems to avoid the problem.
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Alexey Dobriyan reported trouble with LTP with the new fast-gup code,
and Johannes Weiner debugged it to non-page-aligned addresses, where the
new get_user_pages_fast() code would do all the wrong things, including
just traversing past the end of the requested area due to 'addr' never
matching 'end' exactly.
This is not a pretty fix, and we may actually want to move the alignment
into generic code, leaving just the core code per-arch, but Alexey
verified that the vmsplice01 LTP test doesn't crash with this.
Reported-and-tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Debugged-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove arch-specific show_mem() in favor of the generic version.
This also removes the following redundant information display:
- pages in swapcache, printed by show_swap_cache_info()
- dirty pages, writeback pages, mapped pages, slab pages,
pagetable pages, printed by show_free_areas()
where show_mem() calls show_free_areas(), which calls
show_swap_cache_info().
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement get_user_pages_fast without locking in the fastpath on x86.
Do an optimistic lockless pagetable walk, without taking mmap_sem or any
page table locks or even mmap_sem. Page table existence is guaranteed by
turning interrupts off (combined with the fact that we're always looking
up the current mm, means we can do the lockless page table walk within the
constraints of the TLB shootdown design). Basically we can do this
lockless pagetable walk in a similar manner to the way the CPU's pagetable
walker does not have to take any locks to find present ptes.
This patch (combined with the subsequent ones to convert direct IO to use
it) was found to give about 10% performance improvement on a 2 socket 8
core Intel Xeon system running an OLTP workload on DB2 v9.5
"To test the effects of the patch, an OLTP workload was run on an IBM
x3850 M2 server with 2 processors (quad-core Intel Xeon processors at
2.93 GHz) using IBM DB2 v9.5 running Linux 2.6.24rc7 kernel. Comparing
runs with and without the patch resulted in an overall performance
benefit of ~9.8%. Correspondingly, oprofiles showed that samples from
__up_read and __down_read routines that is seen during thread contention
for system resources was reduced from 2.8% down to .05%. Monitoring the
/proc/vmstat output from the patched run showed that the counter for
fast_gup contained a very high number while the fast_gup_slow value was
zero."
(fast_gup is the old name for get_user_pages_fast, fast_gup_slow is a
counter we had for the number of times the slowpath was invoked).
The main reason for the improvement is that DB2 has multiple threads each
issuing direct-IO. Direct-IO uses get_user_pages, and thus the threads
contend the mmap_sem cacheline, and can also contend on page table locks.
I would anticipate larger performance gains on larger systems, however I
think DB2 uses an adaptive mix of threads and processes, so it could be
that thread contention remains pretty constant as machine size increases.
In which case, we stuck with "only" a 10% gain.
The downside of using get_user_pages_fast is that if there is not a pte
with the correct permissions for the access, we end up falling back to
get_user_pages and so the get_user_pages_fast is a bit of extra work.
However this should not be the common case in most performance critical
code.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: Kconfig fix]
[akpm@linux-foundation.org: Makefile fix/cleanup]
[akpm@linux-foundation.org: warning fix]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Reviewed-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an hugepagesz=... option similar to IA64, PPC etc. to x86-64.
This finally allows to select GB pages for hugetlbfs in x86 now that all
the infrastructure is in place.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Straight forward extensions for huge pages located in the PUD instead of
PMDs.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The goal of this patchset is to support multiple hugetlb page sizes. This
is achieved by introducing a new struct hstate structure, which
encapsulates the important hugetlb state and constants (eg. huge page
size, number of huge pages currently allocated, etc).
The hstate structure is then passed around the code which requires these
fields, they will do the right thing regardless of the exact hstate they
are operating on.
This patch adds the hstate structure, with a single global instance of it
(default_hstate), and does the basic work of converting hugetlb to use the
hstate.
Future patches will add more hstate structures to allow for different
hugetlbfs mounts to have different page sizes.
[akpm@linux-foundation.org: coding-style fixes]
Acked-by: Adam Litke <agl@us.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to be able to debug things like the X server and programs using
the PPC Cell SPUs, the debugger needs to be able to access device memory
through ptrace and /proc/pid/mem.
This patch:
Add the generic_access_phys access function and put the hooks in place
to allow access_process_vm to access device or PPC Cell SPU memory.
[riel@redhat.com: Add documentation for the vm_ops->access function]
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Benjamin Herrensmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a lot of places that define either a single bootmem descriptor or an
array of them. Use only one central array with MAX_NUMNODES items instead.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
declared do_page_fault() in asm-x86/trap.h for both X86_32 and X86_64
removed do_invalid_op declaration from mm/fault.c as it is already declared in asm-x86/trap.h
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
included <asm/smp.h> in mm/init_32.c for zap_low_mappings()
declared free_initmem() in asm-x86/page_XX.h
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
PTE_PFN_MASK was getting lonely, so I made it a friend.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rusty, in his peevish way, complained that macros defining constants
should have a name which somewhat accurately reflects the actual
purpose of the constant.
Aside from the fact that PTE_MASK gives no clue as to what's actually
being masked, and is misleadingly similar to the functionally entirely
different PMD_MASK, PUD_MASK and PGD_MASK, I don't really see what the
problem is.
But if this patch silences the incessent noise, then it will have
achieved its goal (TODO: write test-case).
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are a couple of places where (P)Dprintk is used which is an old
compile time enabled printk wrapper. Convert it to the generic
pr_debug().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
From: Arjan van de Ven <arjan@infradead.org>
Date: Sat, 19 Jul 2008 15:47:17 -0700
CONFIG_NONPROMISC_DEVMEM was a rather confusing name - but renaming it
to CONFIG_PROMISC_DEVMEM causes problems on architectures that do not
support this feature; this patch renames it to CONFIG_STRICT_DEVMEM,
so that architectures can opt-in into it.
( the polarity of the option is still the same as it was originally; it
needs to be for now to not break architectures that don't have the
infastructure yet to support this feature)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: "V.Radhakrishnan" <rk@atr-labs.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
Add a debugfs interface to list out all the PAT memtype reservations.
Appears at debugfs x86/pat_memtype_list and output format is
type @ <start addr>-<end addr>
We do not hold the lock while printing the entire list. So, the list may not be
a consistent copy in case where regions are getting added or deleted
at the same time.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
it's separate functionality that deserves its own file.
This also prepares 32-bit memtest support.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus observed:
> The real bug is that we shouldn't have "double negatives", and
> certainly not negative config options. Making that "promiscuous
> /dev/mem" option a negated thing as a config option was bad.
right ... lets rename this option. There should never be a negation
in config options.
[ that reminds me of CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER, but that
is for another commit ;-) ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix asm/e820.h for userspace inclusion
x86: fix numaq_tsc_disable
x86: fix kernel_physical_mapping_init() for large x86 systems
Synchronized tables with current specifications.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Fix bug in kernel_physical_mapping_init() that causes kernel
page table to be built incorrectly for systems with greater
than 512GB of memory.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
optimization: try to merge the range with same page size in
init_memory_mapping, to get the best possible linear mappings set up.
thus when GBpages is not there, we could do 2M pages.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
tighten the boundary checks around max_low_pfn_mapped - dont overmap
nor undermap into holes.
also print out tseg for AMD cpus, for diagnostic purposes.
(this is an SMM area, and we split up any big mappings around that area)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when more than 4g memory is installed, don't map the big hole below 4g.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
save the SLIT, in case we are using fixmap to read it, and that fixmap
could be cleared by others.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add ioremap_default(), which gives a sane mapping without worrying about
type conflicts.
Use it in /dev/mem read in place of ioremap(), as with ioremap(),
any mapping of the region (other than UC_MINUS) will cause a conflict
and failure of /dev/mem read.
Should address the vbetest failure reported at:
http://bugzilla.kernel.org/show_bug.cgi?id=11057
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix phys_pmd_init to make sure not to return bigger value than end.
also print out range split:1G/2M/4K in init_memory_mapping().
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
handle head and tail that are not aligned to big pages (2MB/1GB boundary).
with this patch, on system that support gbpages, change:
last_map_addr: 1080000000 end: 1078000000
to:
last_map_addr: 1078000000 end: 1078000000
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
prepare for overmapped patch
also printout last_map_addr together with end
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/mm/pgtable_32.c:144: warning: 'fixmaps' defined but not used
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
we already have the same srat handling interface for 32bit.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rather than using _PAGE_GLOBAL - which not all CPUs support - to test
CPA, use one of the reserved-for-software-use PTE flags instead. This
allows CPA testing to work on CPUs which don't support PGD.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
From: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Older x86-32 processors do not support global mappings (PGD), so must
only use it if the processor supports it.
The _PAGE_KERNEL* flags always have _PAGE_KERNEL set, since logically
we always want it set.
This is OK even on processors which do not support PGD, since all
_PAGE flags are masked with __supported_pte_mask before being turned
into a real in-pagetable pte. On 32-bit systems, __supported_pte_mask
is initialized to not contain _PAGE_GLOBAL, and it is then added if
the CPU is found to support it.
The x86-32 code used to use __PAGE_KERNEL/__PAGE_KERNEL_EXEC for this
purpose, but they're now redundant and can be removed.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When allocating a new pud, unconditionally populate the pgd (why did
we bother to create a new pud if we weren't going to populate it?).
This will only happen if the pgd slot was empty, since any existing
pud will be reused.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move out e820_register_active_regions from non numa zones_sizes_init()
and remove numa version zones_sizes_init().
and let 32 bit call remove_all_active_ranges() in setup_arch() directly
like 64-bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
kva ram already mapped right after away, so don't need to get that for low ram.
avoid wasting one copy of pgdat.
also add node id in early_res name in case we get it from find_e820_area.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
use PMD_SHIFT to calculate boundary also adjust size for pre-allocated
table size
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
some ram-end boundary only has page alignment, instead of 2M alignment.
v2: make init_memory_mapping more solid: start could be any value other than 0
v3: fix NON PAE by handling left over in kernel_physical_mapping
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar wrote:
> that fixed the build but now we've got a boot crash with this config:
>
> time.c: Detected 2010.304 MHz processor.
> spurious 8259A interrupt: IRQ7.
> BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
> IP: [<0000000000000000>]
> PGD 0
> Thread overran stack, or stack corrupted
> Oops: 0010 [1] SMP
> CPU 0
>
I don't know if this will fix this bug, but it's definitely a bugfix.
It was trashing random pages by overwriting them with pagetables...
Don't trash a large pmd's data when mapping physical memory.
This is a bugfix for "x86_64: adjust mapping of physical pagetables
to work with Xen".
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
do that in init_memory_mapping
also remove one init_ohci1394_dma_on_all_controllers
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The patch "x86: introduce init_memory_mapping for 32bit" does not allocate
enough space for PTEs if the CPU does not implement PSE.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We will need to set a pte on l3_user_pgt. Extract set_pte_vaddr_pud()
from set_pte_vaddr(), that will accept the l3 page table as parameter.
This change should be a no-op for existing code.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If PSE is not available, then fall back to 4k page mappings for the
vmemmap area.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This makes a few of changes to the construction of the initial
pagetables to work better with paravirt_ops/Xen. The main areas
are:
1. Support non-PSE mapping of memory, since Xen doesn't currently
allow 2M pages to be mapped in guests.
2. Make sure that the ioremap alias of all pages are dropped before
attaching the new page to the pagetable. This avoids having
writable aliases of pagetable pages.
3. Preserve existing pagetable entries, rather than overwriting. Its
possible that a fair amount of pagetable has already been constructed,
so reuse what's already in place rather than ignoring and overwriting it.
The algorithm relies on the invariant that any page which is part of
the kernel pagetable is itself mapped in the linear memory area. This
way, it can avoid using ioremap on a pagetable page.
The invariant holds because it maps memory from low to high addresses,
and also allocates memory from low to high. Each allocated page can
map at least 2M of address space, so the mapped area will always
progress much faster than the allocated area. It relies on the early
boot code mapping enough pages to get started.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jan Beulich points out that vmalloc_sync_all() assumes that the
kernel's pmd is always expected to be present in the pgd. The current
pgd construction code will add the pgd to the pgd_list before its pmds
have been pre-populated, thereby making it visible to
vmalloc_sync_all().
However, because pgd_prepopulate_pmd also does the allocation, it may
block and cannot be done under spinlock.
The solution is to preallocate the pmds out of the spinlock, then
populate them while holding the pgd_list lock.
This patch also pulls the pmd preallocation and mop-up functions out
to be common, assuming that the compiler will generate no code for
them when PREALLOCTED_PMDS is 0. Also, there's no need for pgd_ctor
to clear the pgd again, since it's allocated as a zeroed page.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add hooks which are called at pgd_alloc/free time. The pgd_alloc hook
may return an error code, which if non-zero, causes the pgd allocation
to be failed. The hooks may be used to allocate/free auxillary
per-pgd information.
also fix:
> * Ingo Molnar <mingo@elte.hu> wrote:
>
> include/asm/pgalloc.h: In function ‘paravirt_pgd_free':
> include/asm/pgalloc.h:14: error: parameter name omitted
> arch/x86/kernel/entry_64.S: In file included from
> arch/x86/kernel/traps_64.c:51:include/asm/pgalloc.h: In function ‘paravirt_pgd_free':
> include/asm/pgalloc.h:14: error: parameter name omitted
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
vmalloc_sync_all() is only called from register_die_notifier and
alloc_vm_area. Neither is on any performance-critical paths, so
vmalloc_sync_all() itself is not on any hot paths.
Given that the optimisations in vmalloc_sync_all add a fair amount of
code and complexity, and are fairly hard to evaluate for correctness,
it's better to just remove them to simplify the code rather than worry
about its absolute performance.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
that range is from find_e820_area, so don't try to use end_pfn to see
if out of boundary...use table_top instead to avoid possible strange
result while cross the boundary...
also change early_printk to printk, because init_memory_mapping is after
early param parsing, and console=uart8250 already working at that time.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
... so can we use mem below max_low_pfn earlier.
this allows us to move several functions more early instead of waiting
to after paging_init.
That includes moving relocate_initrd() earlier in the bootup, and kva
related early setup done in initmem_init. (in followup patches)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The 32-bit early_ioremap will work equally well for 64-bit, so just use it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use the _populate() functions to attach new pages to a pagetable, to
make sure the right paravirt_ops calls get called.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
those function depend on paging setup pgtable, so they could access
the ram in bootmem region but just get mapped.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
for 32bit
we already had early_res support, so don't need to track min_low_pfn.
keep it to 0 always.
also use init_bootmem_node instead of init_bootmem, so don't touch
min_low_pfn.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so that max_low_pfn is not changed after it is set.
so we can move that early and out of initmem_init.
could call find_low_pfn_range just after max_pfn is set.
also could move reserve_initrd out of setup_bootmem_allocator
so 32bit is more like 64bit.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
want to remove arch_get_ram_range, and use early_node_map instead.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Making a variable page-aligned by using
__attribute__((section(".data.page_aligned"))) is fragile because if
sizeof(variable) is not also a multiple of page size, it leaves
variables in the remainder of the section unaligned.
This patch introduces two new qualifiers, __page_aligned_data and
__page_aligned_bss to set the section *and* the alignment of
variables. This makes page-aligned variables more robust because the
linker will make sure they're aligned properly. Unfortunately it
requires *all* page-aligned data to use these macros...
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds a 'flags' parameter to reserve_bootmem_generic() like it
already has been added in reserve_bootmem() with commit
72a7fe3967.
It also changes all users to use BOOTMEM_DEFAULT, which doesn't effectively
change the behaviour. Since the change is x86-specific, I don't think it's
necessary to add a new API for migration. There are only 4 users of that
function.
The change is necessary for the next patch, using reserve_bootmem_generic()
for crashkernel reservation.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
sparse mutters:
arch/x86/mm/numa_64.c:195:27: warning: symbol 'end_pfn' shadows an earlier one
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
plat_node_bdata, cmdline, nodemap_addr, nodemap_size are local to
numa_64.c. Make them static
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Consolidate node_to_cpumask operations and remove the 256k
byte node_to_cpumask_map. This is done by allocating the
node_to_cpumask_map array after the number of possible nodes
(nr_node_ids) is known.
* Debug printouts when CONFIG_DEBUG_PER_CPU_MAPS is active have
been increased. It now shows faults when calling node_to_cpumask()
and node_to_cpumask_ptr().
For inclusion into sched-devel/latest tree.
Based on:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
+ sched-devel/latest .../mingo/linux-2.6-sched-devel.git
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* Introduce a new PER_CPU macro called "EARLY_PER_CPU". This is
used by some per_cpu variables that are initialized and accessed
before there are per_cpu areas allocated.
["Early" in respect to per_cpu variables is "earlier than the per_cpu
areas have been setup".]
This patchset adds these new macros:
DEFINE_EARLY_PER_CPU(_type, _name, _initvalue)
EXPORT_EARLY_PER_CPU_SYMBOL(_name)
DECLARE_EARLY_PER_CPU(_type, _name)
early_per_cpu_ptr(_name)
early_per_cpu_map(_name, _idx)
early_per_cpu(_name, _cpu)
The DEFINE macro defines the per_cpu variable as well as the early
map and pointer. It also initializes the per_cpu variable and map
elements to "_initvalue". The early_* macros provide access to
the initial map (usually setup during system init) and the early
pointer. This pointer is initialized to point to the early map
but is then NULL'ed when the actual per_cpu areas are setup. After
that the per_cpu variable is the correct access to the variable.
The early_per_cpu() macro is not very efficient but does show how to
access the variable if you have a function that can be called both
"early" and "late". It tests the early ptr to be NULL, and if not
then it's still valid. Otherwise, the per_cpu variable is used
instead:
#define early_per_cpu(_name, _cpu) \
(early_per_cpu_ptr(_name) ? \
early_per_cpu_ptr(_name)[_cpu] : \
per_cpu(_name, _cpu))
A better method is to actually check the pointer manually. In the
case below, numa_set_node can be called both "early" and "late":
void __cpuinit numa_set_node(int cpu, int node)
{
int *cpu_to_node_map = early_per_cpu_ptr(x86_cpu_to_node_map);
if (cpu_to_node_map)
cpu_to_node_map[cpu] = node;
else
per_cpu(x86_cpu_to_node_map, cpu) = node;
}
* Add a flag "arch_provides_topology_pointers" that indicates pointers
to topology cpumask_t maps are available. Otherwise, use the function
returning the cpumask_t value. This is useful if cpumask_t set size
is very large to avoid copying data on to/off of the stack.
* The coverage of CONFIG_DEBUG_PER_CPU_MAPS has been increased while
the non-debug case has been optimized a bit.
* Remove an unreferenced compiler warning in drivers/base/topology.c
* Clean up #ifdef in setup.c
For inclusion into sched-devel/latest tree.
Based on:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
+ sched-devel/latest .../mingo/linux-2.6-sched-devel.git
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
so don't punish all other cpus without that problem when init highmem
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
use early_node_map to init high pages, so we can remove page_is_ram() and
page_is_reserved_early() in the big loop with add_one_highpage
also remove page_is_reserved_early(), it is not needed anymore.
v2: fix the build of other platforms
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
in case we have kva before ramdisk on a node, we still need to use
those ranges.
v2: reserve_early kva ram area, in case there are holes in highmem, to avoid
those area could be treat as free high pages.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
1. add reserve_bootmem_generic for 32bit
2. change len to unsigned long
3. make early_res_to_bootmem to use it
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds a 'flags' parameter to reserve_bootmem_generic() like it
already has been added in reserve_bootmem() with commit
72a7fe3967.
It also changes all users to use BOOTMEM_DEFAULT, which doesn't effectively
change the behaviour. Since the change is x86-specific, I don't think it's
necessary to add a new API for migration. There are only 4 users of that
function.
The change is necessary for the next patch, using reserve_bootmem_generic()
for crashkernel reservation.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
