If a raid1 has only one working drive and it has a sector which
gives an error on read, then an attempt to recover onto a spare will
fail, but as the single remaining drive is not removed from the
array, the recovery will be immediately re-attempted, resulting
in an infinite recovery loop.
So detect this situation and don't retry recovery once an error
on the lone remaining drive is detected.
Allow recovery to be retried once every time a spare is added
in case the problem wasn't actually a media error.
Signed-off-by: NeilBrown <neilb@suse.de>
Using sequential numbers to identify md devices is somewhat artificial.
Using names can be a lot more user-friendly.
Also, creating md devices by opening the device special file is a bit
awkward.
So this patch provides a new option for creating and naming devices.
Writing a name such as "md_home" to
/sys/modules/md_mod/parameters/new_array
will cause an array with that name to be created. It will appear in
/sys/block/ /proc/partitions and /proc/mdstat as 'md_home'.
It will have an arbitrary minor number allocated.
md devices that a created by an open are destroyed on the last
close when the device is inactive.
For named md devices, they will not be destroyed until the array
is explicitly stopped, either with the STOP_ARRAY ioctl or by
writing 'clear' to /sys/block/md_XXXX/md/array_state.
The name of the array must start 'md_' to avoid conflict with
other devices.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently md devices, once created, never disappear until the module
is unloaded. This is essentially because the gendisk holds a
reference to the mddev, and the mddev holds a reference to the
gendisk, this a circular reference.
If we drop the reference from mddev to gendisk, then we need to ensure
that the mddev is destroyed when the gendisk is destroyed. However it
is not possible to hook into the gendisk destruction process to enable
this.
So we drop the reference from the gendisk to the mddev and destroy the
gendisk when the mddev gets destroyed. However this has a
complication.
Between the call
__blkdev_get->get_gendisk->kobj_lookup->md_probe
and the call
__blkdev_get->md_open
there is no obvious way to hold a reference on the mddev any more, so
unless something is done, it will disappear and gendisk will be
destroyed prematurely.
Also, once we decide to destroy the mddev, there will be an unlockable
moment before the gendisk is unlinked (blk_unregister_region) during
which a new reference to the gendisk can be created. We need to
ensure that this reference can not be used. i.e. the ->open must
fail.
So:
1/ in md_probe we set a flag in the mddev (hold_active) which
indicates that the array should be treated as active, even
though there are no references, and no appearance of activity.
This is cleared by md_release when the device is closed if it
is no longer needed.
This ensures that the gendisk will survive between md_probe and
md_open.
2/ In md_open we check if the mddev we expect to open matches
the gendisk that we did open.
If there is a mismatch we return -ERESTARTSYS and modify
__blkdev_get to retry from the top in that case.
In the -ERESTARTSYS sys case we make sure to wait until
the old gendisk (that we succeeded in opening) is really gone so
we loop at most once.
Some udev configurations will always open an md device when it first
appears. If we allow an md device that was just created by an open
to disappear on an immediate close, then this can race with such udev
configurations and result in an infinite loop the device being opened
and closed, then re-open due to the 'ADD' even from the first open,
and then close and so on.
So we make sure an md device, once created by an open, remains active
at least until some md 'ioctl' has been made on it. This means that
all normal usage of md devices will allow them to disappear promptly
when not needed, but the worst that an incorrect usage will do it
cause an inactive md device to be left in existence (it can easily be
removed).
As an array can be stopped by writing to a sysfs attribute
echo clear > /sys/block/mdXXX/md/array_state
we need to use scheduled work for deleting the gendisk and other
kobjects. This allows us to wait for any pending gendisk deletion to
complete by simply calling flush_scheduled_work().
Signed-off-by: NeilBrown <neilb@suse.de>
md_free is the .release handler for the md kobj_type.
So it makes sense to release all the objects referenced by
the mddev in there, rather than just prior to calling kobject_put
for what we think is the last time.
Signed-off-by: NeilBrown <neilb@suse.de>
It is more balanced to just do simple initialisation in mddev_find,
which allocates and links a new md device, and leave all the
more sophisticated allocation to md_probe (which calls mddev_find).
md_probe already allocated the gendisk. It should allocate the
queue too.
Signed-off-by: NeilBrown <neilb@suse.de>
The rdev_for_each macro defined in <linux/raid/md_k.h> is identical to
list_for_each_entry_safe, from <linux/list.h>, it should be defined to
use list_for_each_entry_safe, instead of reinventing the wheel.
But some calls to each_entry_safe don't really need a safe version,
just a direct list_for_each_entry is enough, this could save a temp
variable (tmp) in every function that used rdev_for_each.
In this patch, most rdev_for_each loops are replaced by list_for_each_entry,
totally save many tmp vars; and only in the other situations that will call
list_del to delete an entry, the safe version is used.
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the hash_spacing and preshift members of struct
raid0_private_data to spacing and sector_shift respectively and
changes the semantics as follows:
We always have spacing = 2 * hash_spacing. In case
sizeof(sector_t) > sizeof(u32) we also have sector_shift = preshift + 1
while sector_shift = preshift = 0 otherwise.
Note that the values of nb_zone and zone are unaffected by these changes
because in the sector_div() preceeding the assignement of these two
variables both arguments double.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
This completes the block -> sector conversion of struct strip_zone.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
current_offset and curr_zone_offset stored the corresponding offsets
as 1K quantities. Rename them to current_start and curr_zone_start
to match the naming of struct strip_zone and store the offsets as
sector counts.
Also, add KERN_INFO to the printk() affected by this change to make
checkpatch happy.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
For the same reason as in the previous patch, rename it from zone_offset
to zone_start.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Rename zone->dev_offset to zone->dev_start to make sure all users
have been converted.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
There is no compelling need for this, but sysfs_notify_dirent is a
nicer interface and the change is good for consistency.
Signed-off-by: NeilBrown <neilb@suse.de>
commit a2ed9615e3
fixed a bug with 'internal' bitmaps, but in the process broke
'in a file' bitmaps. So they are broken in 2.6.28
This fixes it, and needs to go in 2.6.28-stable.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Supply dm_add_exception as a callback to the read_metadata function.
Add a status function ready for a later patch and name the functions
consistently.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move the existing snapshot exception store implementations out into
separate files. Later patches will place these behind a new
interface in preparation for alternative implementations.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename struct exception_store to dm_exception_store.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull structures that bridge the gap between snapshot and
exception store out of dm-snap.h and put them in a new
.h file - dm-exception-store.h. This file will define the
API for new exception stores.
Ultimately, dm-snap.h is unnecessary, since only dm-snap.c
should be using it.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The same workqueue is used both for sending uevents and processing queued I/O.
Deadlock has been reported in RHEL5 when sending a uevent was blocked waiting
for the queued I/O to be processed. Use scheduled_work() for the asynchronous
uevents instead.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Implement simple read-only sysfs entry for device-mapper block device.
This patch adds a simple sysfs directory named "dm" under block device
properties and implements
- name attribute (string containing mapped device name)
- uuid attribute (string containing UUID, or empty string if not set)
The kobject is embedded in mapped_device struct, so no additional
memory allocation is needed for initializing sysfs entry.
During the processing of sysfs attribute we need to lock mapped device
which is done by a new function dm_get_from_kobj, which returns the md
associated with kobject and increases the usage count.
Each 'show attribute' function is responsible for its own locking.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rework table reference counting.
The existing code uses a reference counter. When the last reference is
dropped and the counter reaches zero, the table destructor is called.
Table reference counters are acquired/released from upcalls from other
kernel code (dm_any_congested, dm_merge_bvec, dm_unplug_all).
If the reference counter reaches zero in one of the upcalls, the table
destructor is called from almost random kernel code.
This leads to various problems:
* dm_any_congested being called under a spinlock, which calls the
destructor, which calls some sleeping function.
* the destructor attempting to take a lock that is already taken by the
same process.
* stale reference from some other kernel code keeps the table
constructed, which keeps some devices open, even after successful
return from "dmsetup remove". This can confuse lvm and prevent closing
of underlying devices or reusing device minor numbers.
The patch changes reference counting so that the table destructor can be
called only at predetermined places.
The table has always exactly one reference from either mapped_device->map
or hash_cell->new_map. After this patch, this reference is not counted
in table->holders. A pair of dm_create_table/dm_destroy_table functions
is used for table creation/destruction.
Temporary references from the other code increase table->holders. A pair
of dm_table_get/dm_table_put functions is used to manipulate it.
When the table is about to be destroyed, we wait for table->holders to
reach 0. Then, we call the table destructor. We use active waiting with
msleep(1), because the situation happens rarely (to one user in 5 years)
and removing the device isn't performance-critical task: the user doesn't
care if it takes one tick more or not.
This way, the destructor is called only at specific points
(dm_table_destroy function) and the above problems associated with lazy
destruction can't happen.
Finally remove the temporary protection added to dm_any_congested().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Implement barrier support for single device DM devices
This patch implements barrier support in DM for the common case of dm linear
just remapping a single underlying device. In this case we can safely
pass the barrier through because there can be no reordering between
devices.
NB. Any DM device might cease to support barriers if it gets
reconfigured so code must continue to allow for a possible
-EOPNOTSUPP on every barrier bio submitted. - agk
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow NULL buffer in dm_copy_name_and_uuid if you only want to return one of
the fields.
(Required by a following patch that adds these fields to sysfs.)
Signed-off-by: Milan Broz <mbroz@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Check that the log bitmap will fit within the log device.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move log size validation from mirror target to log constructor.
Removed PAGE_SIZE restriction we no longer think necessary.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
rw_header function updates three members of io_req data every time
when I/O is processed. bi_rw and notify.fn are never modified once
they get initialized, and so they can be set in advance.
header_to_disk() can also be pulled out of write_header() since only one
caller needs it and write_header() can be replaced by rw_header()
directly.
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change dm_unregister_target to return void and use BUG() for error
reporting.
dm_unregister_target can only fail because of programming bug in the
target driver. It can't fail because of user's behavior or disk errors.
This patch changes unregister_target to return void and use BUG if
someone tries to unregister non-registered target or unregister target
that is in use.
This patch removes code duplication (testing of error codes in all dm
targets) and reports bugs in just one place, in dm_unregister_target. In
some target drivers, these return codes were ignored, which could lead
to a situation where bugs could be missed.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Always increase the error count when I/O on a leg of a mirror fails.
The error count is used to decide whether to select an alternative
mirror leg. If the target doesn't use the "handle_errors" feature, the
error count is not updated and the bio can get requeued forever by the
read callback.
Fix it by increasing error_count before the handle_errors feature
checking.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
In create_log_context function, dm_io_client_destroy function needs
to be called, when memory allocation of disk_header, sync_bits and
recovering_bits failed, but dm_io_client_destroy is not called.
Cc: stable@kernel.org
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Acked-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change yield() to msleep(1). If the thread had realtime priority,
yield() doesn't really yield, so the yielding process would loop
indefinitely and cause machine lockup.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move one dm_table_put() so that the last reference in the thread
gets dropped in __unbind().
This is required for a following patch,
dm-table-rework-reference-counting.patch, which will change the logic in
such a way that table destructor is called only at specific points in
the code.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Instead of having a global bio slab cache, add a reference to one
in each bio_set that is created. This allows for personalized slabs
in each bio_set, so that they can have bios of different sizes.
This means we can personalize the bios we return. File systems may
want to embed the bio inside another structure, to avoid allocation
more items (and stuffing them in ->bi_private) after the get a bio.
Or we may want to embed a number of bio_vecs directly at the end
of a bio, to avoid doing two allocations to return a bio. This is now
possible.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When we read the write-intent-bitmap off the device, we currently
read a whole number of pages.
When PAGE_SIZE is 4K, this works due to the alignment we enforce
on the superblock and bitmap.
When PAGE_SIZE is 64K, this case read past the end-of-device
which causes an error.
When we write the superblock, we ensure to clip the last page
to just be the required size. Copy that code into the read path
to just read the required number of sectors.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: stable@kernel.org
Fix setting of max_segment_size and seg_boundary mask for stacked md/dm
devices.
When stacking devices (LVM over MD over SCSI) some of the request queue
parameters are not set up correctly in some cases by default, namely
max_segment_size and and seg_boundary mask.
If you create MD device over SCSI, these attributes are zeroed.
Problem become when there is over this mapping next device-mapper mapping
- queue attributes are set in DM this way:
request_queue max_segment_size seg_boundary_mask
SCSI 65536 0xffffffff
MD RAID1 0 0
LVM 65536 -1 (64bit)
Unfortunately bio_add_page (resp. bio_phys_segments) calculates number of
physical segments according to these parameters.
During the generic_make_request() is segment cout recalculated and can
increase bio->bi_phys_segments count over the allowed limit. (After
bio_clone() in stack operation.)
Thi is specially problem in CCISS driver, where it produce OOPS here
BUG_ON(creq->nr_phys_segments > MAXSGENTRIES);
(MAXSEGENTRIES is 31 by default.)
Sometimes even this command is enough to cause oops:
dd iflag=direct if=/dev/<vg>/<lv> of=/dev/null bs=128000 count=10
This command generates bios with 250 sectors, allocated in 32 4k-pages
(last page uses only 1024 bytes).
For LVM layer, it allocates bio with 31 segments (still OK for CCISS),
unfortunatelly on lower layer it is recalculated to 32 segments and this
violates CCISS restriction and triggers BUG_ON().
The patch tries to fix it by:
* initializing attributes above in queue request constructor
blk_queue_make_request()
* make sure that blk_queue_stack_limits() inherits setting
(DM uses its own function to set the limits because it
blk_queue_stack_limits() was introduced later. It should probably switch
to use generic stack limit function too.)
* sets the default seg_boundary value in one place (blkdev.h)
* use this mask as default in DM (instead of -1, which differs in 64bit)
Bugs related to this:
https://bugzilla.redhat.com/show_bug.cgi?id=471639http://bugzilla.kernel.org/show_bug.cgi?id=8672
Signed-off-by: Milan Broz <mbroz@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Port to the new tracepoints API: split DEFINE_TRACE() and DECLARE_TRACE()
sites. Spread them out to the usage sites, as suggested by
Mathieu Desnoyers.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
This was a forward port of work done by Mathieu Desnoyers, I changed it to
encode the 'what' parameter on the tracepoint name, so that one can register
interest in specific events and not on classes of events to then check the
'what' parameter.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
dm_any_congested() just checks for the DMF_BLOCK_IO and has no
code to make sure that suspend waits for dm_any_congested() to
complete. This patch adds such a check.
Without it, a race can occur with dm_table_put() attempting to
destroying the table in the wrong thread, the one running
dm_any_congested() which is meant to be quick and return
immediately.
Two examples of problems:
1. Sleeping functions called from congested code, the caller
of which holds a spin lock.
2. An ABBA deadlock between pdflush and multipathd. The two locks
in contention are inode lock and kernel lock.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This doesn't fix any bug, just moves wake_up immediately after decrementing
md->pending, for better code readability.
It must be clear to anyone manipulating md->pending to wake up
the queue if md->pending reaches zero, so move the wakeup as close to
the decrementing as possible.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Currently dm ignores the parameters provided to hardware handlers
without providing any notifications to the user.
This patch just prints a warning message so that the user knows that
the arguments are ignored.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Path activation code is called even when the pgpath is NULL. This could
lead to a panic in activate_path(). Such a panic is seen in -rt kernel.
This problem has been there before the pg_init() was moved to a
workqueue.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Don't proceed if dm_stripe_init() fails to register itself as a dm target.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
We queue work on keventd queue --- so this queue must be flushed in the
destructor. Otherwise, keventd could access mirror_set after it was freed.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org
We currently oops with a divide error on starting a linear software
raid array consisting of at least two very small (< 500K) devices.
The bug is caused by the calculation of the hash table size which
tries to compute sector_div(sz, base) with "base" being zero due to
the small size of the component devices of the array.
Fix this by requiring the hash spacing to be at least one which
implies that also "base" is non-zero.
This bug has existed since about 2.6.14.
Cc: stable@kernel.org
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Adding a spare to a raid10 doesn't cause recovery to start.
This is due to an silly type in
commit 6c2fce2ef6
and so is a bug in 2.6.27 and .28-rc.
Thanks to Thomas Backlund for bisecting to find this.
Cc: Thomas Backlund <tmb@mandriva.org>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
It turns out that it is only safe to call blkdev_ioctl when the device
is actually open (as ->bd_disk is set to NULL on last close). And it
is quite possible for do_md_stop to be called when the device is not
open. So discard the call to blkdev_ioctl(BLKRRPART) which was
added in
commit 934d9c23b4
It is just as easy to call this ioctl from userspace when needed (on
mdadm -S) so leave it out of the kernel
Signed-off-by: NeilBrown <neilb@suse.de>
If there are several snapshots sharing an origin and one is removed
while the origin is being written to, the snapshot's mempool may get
deleted while elements are still referenced.
Prior to dm-snapshot-use-per-device-mempools.patch the pending
exceptions may still have been referenced after the snapshot was
destroyed, but this was not a problem because the shared mempool
was still there.
This patch fixes the problem by tracking the number of mempool elements
in use.
The scenario:
- You have an origin and two snapshots 1 and 2.
- Someone writes to the origin.
- It creates two exceptions in the snapshots, snapshot 1 will be primary
exception, snapshot 2's pending_exception->primary_pe will point to the
exception in snapshot 1.
- The exceptions are being relocated, relocation of exception 1 finishes
(but it's pending_exception is still allocated, because it is referenced
by an exception from snapshot 2)
- The user lvremoves snapshot 1 --- it calls just suspend (does nothing)
and destructor. md->pending is zero (there is no I/O submitted to the
snapshot by md layer), so it won't help us.
- The destructor waits for kcopyd jobs to finish on snapshot 1 --- but
there are none.
- The destructor on snapshot 1 cleans up everything.
- The relocation of exception on snapshot 2 finishes, it drops reference
on primary_pe. This frees its primary_pe pointer. Primary_pe points to
pending exception created for snapshot 1. So it frees memory into
non-existing mempool.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
register_snapshot() performs a GFP_KERNEL allocation while holding
_origins_lock for write, but that could write out dirty pages onto a
device that attempts to acquire _origins_lock for read, resulting in
deadlock.
So move the allocation up before taking the lock.
This path is not performance-critical, so it doesn't matter that we
allocate memory and free it if we find that we won't need it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
md arrays are not currently destroyed when they are stopped - they
remain in /sys/block. Last time I tried this I tripped over locking
too much.
A consequence of this is that udev doesn't remove anything from /dev.
This is rather ugly.
As an interim measure until proper device removal can be achieved,
make sure all partitions are removed using the BLKRRPART ioctl, and
send a KOBJ_CHANGE when an md array is stopped.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-linus' of git://neil.brown.name/md:
md: allow extended partitions on md devices.
md: use sysfs_notify_dirent to notify changes to md/dev-xxx/state
md: use sysfs_notify_dirent to notify changes to md/array_state
* git://git.kernel.org/pub/scm/linux/kernel/git/viro/bdev: (66 commits)
[PATCH] kill the rest of struct file propagation in block ioctls
[PATCH] get rid of struct file use in blkdev_ioctl() BLKBSZSET
[PATCH] get rid of blkdev_locked_ioctl()
[PATCH] get rid of blkdev_driver_ioctl()
[PATCH] sanitize blkdev_get() and friends
[PATCH] remember mode of reiserfs journal
[PATCH] propagate mode through swsusp_close()
[PATCH] propagate mode through open_bdev_excl/close_bdev_excl
[PATCH] pass fmode_t to blkdev_put()
[PATCH] kill the unused bsize on the send side of /dev/loop
[PATCH] trim file propagation in block/compat_ioctl.c
[PATCH] end of methods switch: remove the old ones
[PATCH] switch sr
[PATCH] switch sd
[PATCH] switch ide-scsi
[PATCH] switch tape_block
[PATCH] switch dcssblk
[PATCH] switch dasd
[PATCH] switch mtd_blkdevs
[PATCH] switch mmc
...
Now that lookup_bdev is exported and used by dm just use it directly
instead of through a trivial wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch tidies local_init() in preparation for request-based dm.
No functional change.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch removes the DM_WQ_FLUSH_ALL state that is unnecessary.
The dm_queue_flush(md, DM_WQ_FLUSH_ALL, NULL) in dm_suspend()
is never invoked because:
- 'goto flush_and_out' is the same as 'goto out' because
the 'goto flush_and_out' is called only when '!noflush'
- If r is non-zero, then the code above will invoke 'goto out'
and skip this code.
No functional change.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Separate the region hash code from raid1 so it can be shared by forthcoming
targets. Use BUG_ON() for failed async dm_io() calls.
Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When a bio gets split, mark its fragments with the BIO_CLONED flag.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove waitqueue no longer needed with the async crypto interface.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When writing io, dm-crypt has to allocate a new cloned bio
and encrypt the data into newly-allocated pages attached to this bio.
In rare cases, because of hw restrictions (e.g. physical segment limit)
or memory pressure, sometimes more than one cloned bio has to be used,
each processing a different fragment of the original.
Currently there is one waitqueue which waits for one fragment to finish
and continues processing the next fragment.
But when using asynchronous crypto this doesn't work, because several
fragments may be processed asynchronously or in parallel and there is
only one crypt context that cannot be shared between the bio fragments.
The result may be corruption of the data contained in the encrypted bio.
The patch fixes this by allocating new dm_crypt_io structs (with new
crypto contexts) and running them independently.
The fragments contains a pointer to the base dm_crypt_io struct to
handle reference counting, so the base one is properly deallocated
after all the fragments are finished.
In a low memory situation, this only uses one additional object from the
mempool. If the mempool is empty, the next allocation simple waits for
previous fragments to complete.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Prepare local sector variable (offset) for later patch.
Do not update io->sector for still-running I/O.
No functional change.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change #include "dm.h" to #include <linux/device-mapper.h> in all targets.
Targets should not need direct access to internal DM structures.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move array_too_big to include/linux/device-mapper.h because it is
used by targets.
Remove the test from dm-raid1 as the number of mirror legs is limited
such that it can never fail. (Even for stripes it seems rather
unlikely.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
We must zero the next chunk on disk *before* writing out the current chunk, not
after. Otherwise if the machine crashes at the wrong time, the "end of metadata"
marker may be missing.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org
Use a separate buffer for writing zeroes to the on-disk snapshot
exception store, make the updating of ps->current_area explicit and
refactor the code in preparation for the fix in the next patch.
No functional change.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
The last_percent field is unused - remove it.
(It dates from when events were triggered as each X% filled up.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a race condition with primary_pe ref_count handling.
put_pending_exception runs under dm_snapshot->lock, it does atomic_dec_and_test
on primary_pe->ref_count, and later does atomic_read primary_pe->ref_count.
__origin_write does atomic_dec_and_test on primary_pe->ref_count without holding
dm_snapshot->lock.
This opens the following race condition:
Assume two CPUs, CPU1 is executing put_pending_exception (and holding
dm_snapshot->lock). CPU2 is executing __origin_write in parallel.
primary_pe->ref_count == 2.
CPU1:
if (primary_pe && atomic_dec_and_test(&primary_pe->ref_count))
origin_bios = bio_list_get(&primary_pe->origin_bios);
... decrements primary_pe->ref_count to 1. Doesn't load origin_bios
CPU2:
if (first && atomic_dec_and_test(&primary_pe->ref_count)) {
flush_bios(bio_list_get(&primary_pe->origin_bios));
free_pending_exception(primary_pe);
/* If we got here, pe_queue is necessarily empty. */
return r;
}
... decrements primary_pe->ref_count to 0, submits pending bios, frees
primary_pe.
CPU1:
if (!primary_pe || primary_pe != pe)
free_pending_exception(pe);
... this has no effect.
if (primary_pe && !atomic_read(&primary_pe->ref_count))
free_pending_exception(primary_pe);
... sees ref_count == 0 (written by CPU 2), does double free !!
This bug can happen only if someone is simultaneously writing to both the
origin and the snapshot.
If someone is writing only to the origin, __origin_write will submit kcopyd
request after it decrements primary_pe->ref_count (so it can't happen that the
finished copy races with primary_pe->ref_count decrementation).
If someone is writing only to the snapshot, __origin_write isn't invoked at all
and the race can't happen.
The race happens when someone writes to the snapshot --- this creates
pending_exception with primary_pe == NULL and starts copying. Then, someone
writes to the same chunk in the snapshot, and __origin_write races with
termination of already submitted request in pending_complete (that calls
put_pending_exception).
This race may be reason for bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=11636https://bugzilla.redhat.com/show_bug.cgi?id=465825
The patch fixes the code to make sure that:
1. If atomic_dec_and_test(&primary_pe->ref_count) returns false, the process
must no longer dereference primary_pe (because someone else may free it under
us).
2. If atomic_dec_and_test(&primary_pe->ref_count) returns true, the process
is responsible for freeing primary_pe.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org
Write throughput to LVM snapshot origin volume is an order
of magnitude slower than those to LV without snapshots or
snapshot target volumes, especially in the case of sequential
writes with O_SYNC on.
The following patch originally written by Kevin Jamieson and
Jan Blunck and slightly modified for the current RCs by myself
tries to improve the performance by modifying the behaviour
of kcopyd, so that it pushes back an I/O job to the head of
the job queue instead of the tail as process_jobs() currently
does when it has to wait for free pages. This way, write
requests aren't shuffled to cause extra seeks.
I tested the patch against 2.6.27-rc5 and got the following results.
The test is a dd command writing to snapshot origin followed by fsync
to the file just created/updated. A couple of filesystem benchmarks
gave me similar results in case of sequential writes, while random
writes didn't suffer much.
dd if=/dev/zero of=<somewhere on snapshot origin> bs=4096 count=...
[conv=notrunc when updating]
1) linux 2.6.27-rc5 without the patch, write to snapshot origin,
average throughput (MB/s)
10M 100M 1000M
create,dd 511.46 610.72 11.81
create,dd+fsync 7.10 6.77 8.13
update,dd 431.63 917.41 12.75
update,dd+fsync 7.79 7.43 8.12
compared with write throughput to LV without any snapshots,
all dd+fsync and 1000 MiB writes perform very poorly.
10M 100M 1000M
create,dd 555.03 608.98 123.29
create,dd+fsync 114.27 72.78 76.65
update,dd 152.34 1267.27 124.04
update,dd+fsync 130.56 77.81 77.84
2) linux 2.6.27-rc5 with the patch, write to snapshot origin,
average throughput (MB/s)
10M 100M 1000M
create,dd 537.06 589.44 46.21
create,dd+fsync 31.63 29.19 29.23
update,dd 487.59 897.65 37.76
update,dd+fsync 34.12 30.07 26.85
Although still not on par with plain LV performance -
cannot be avoided because it's copy on write anyway -
this simple patch successfully improves throughtput
of dd+fsync while not affecting the rest.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Kazuo Ito <ito.kazuo@oss.ntt.co.jp>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Analog of blkdev_driver_ioctl() with sane arguments. For
now uses fake struct file, by the end of the series it won't
and blkdev_driver_ioctl() will become a wrapper around it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The new extended partition support provides a much nicer was
to have partitions on md devices that the 'mdp' alternate major.
We cannot really get rid of 'mdp' at this time, but we can
enable extended partitions as that will probably make life
easier for sysadmins.
Signed-off-by: NeilBrown <neilb@suse.de>
The 'state' file for a device reports, for example, when the device
has failed. Changes should be reported to userspace ASAP without
the possibility of blocking on low-memory. sysfs_notify does
have that possibility (as it takes a mutex which can be held
across a kmalloc) so use sysfs_notify_dirent instead.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that we have sysfs_notify_dirent, use it to notify changes
to md/array_state.
As sysfs_notify_dirent can be called in atomic context, we can
remove the delayed notify and the MD_NOTIFY_ARRAY_STATE flag.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-linus' of git://neil.brown.name/md:
md: fix input truncation in safe_delay_store()
md: check for memory allocation failure in faulty personality
md: build failure due to missing delay.h
md: Relax minimum size restrictions on chunk_size.
md: remove space after function name in declaration and call.
md: Remove unnecessary #includes, #defines, and function declarations.
md: Convert remaining 1k representations in linear.c to sectors.
md: linear.c: Make two local variables sector-based.
md: linear: Represent dev_info->size and dev_info->offset in sectors.
md: linear.c: Remove broken debug code.
md: linear.c: Remove pointless initialization of curr_offset.
md: linear.c: Fix typo in comment.
md: Don't try to set an array to 'read-auto' if it is already in that state.
md: Allow metadata_version to be updated for externally managed metadata.
md: Fix rdev_size_store with size == 0
safe_delay_store() currently truncates the last character of input since
it tells strlcpy that the buffer can only hold 'len' characters, off by
one. sysfs already null terminates the buffer, so just increase the
last argument to strlcpy.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
It's a fault injection module, but I don't think we should oops here.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Today's linux-next build (powerpc ppc64_defconfig) failed like this:
drivers/md/raid1.c: In function 'sync_request':
drivers/md/raid1.c:1759: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid1.o] Error 1
make[3]: *** Waiting for unfinished jobs....
drivers/md/raid10.c: In function 'sync_request':
drivers/md/raid10.c:1749: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid10.o] Error 1
drivers/md/md.c: In function 'md_do_sync':
drivers/md/md.c:5915: error: implicit declaration of function 'msleep'
Caused by commit 6caa3b0bbdb474647f6bdd8a958ffc46f78d8d58 ("md: Remove
unnecessary #includes, #defines, and function declarations"). I added
the following patch.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NeilBrown <neilb@suse.de>
Multipath is best at handling transport errors. If it gets a device
error then there is not much the multipath layer can do. It will just
access the same device but from a different path.
This patch breaks up failfast into device, transport and driver errors.
The multipath layers (md and dm mutlipath) only ask the lower levels to
fast fail transport errors. The user of failfast, read ahead, will ask
to fast fail on all errors.
Note that blk_noretry_request will return true if any failfast bit
is set. This allows drivers that do not support the multipath failfast
bits to continue to fail on any failfast error like before. Drivers
like scsi that are able to fail fast specific errors can check
for the specific fail fast type. In the next patch I will convert
scsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently, the 'chunk_size' of an array must be at-least PAGE_SIZE.
This makes moving an array to a machine with a larger PAGE_SIZE, or
changing the kernel to use a larger PAGE_SIZE, can stop an array from
working.
For RAID10 and RAID4/5/6, this is non-trivial to fix as the resync
process works on whole pages at a time, and assumes them to be wholly
within a stripe. For other raid personalities, this restriction is
not needed at all and can be dropped.
So remove the test on chunk_size from common can, and add it in just
the places where it is needed: raid10 and raid4/5/6.
Signed-off-by: NeilBrown <neilb@suse.de>
Having
function (args)
instead of
function(args)
make is harder to search for calls of particular functions.
So remove all those spaces.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames hash_spacing and preshift to spacing and
sector_shift respectively with the following change of semantics:
Case 1: (sizeof(sector_t) <= sizeof(u32)).
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In this case, we have sector_shift = preshift = 0 and spacing =
2 * hash_spacing.
Hence, the index for the hash table which is computed by the new code
in which_dev() as sector / spacing equals the old value which was
(sector/2) / hash_spacing.
Note also that the value of nb_zone stays the same because both sz
and base double.
Case 2: (sizeof(sector_t) > sizeof(u32)).
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
(aka the shifting dance case). Here we have sector_shift = preshift +
1 and
spacing = 2 * hash_spacing
during the computation of nb_zone and curr_sector, but
spacing = hash_spacing
in which_dev() because in the last hunk of the patch for linear.c we
shift down conf->spacing (= 2 * hash_spacing) by one more bit than
in the old code.
Hence in the computation of nb_zone, sz and base have the same value
as before, so nb_zone is not affected. Also curr_sector in the next
hunk stays the same.
In which_dev() the hash table index is computed as
(sector >> sector_shift) / spacing
In view of sector_shift = preshift + 1 and spacing = hash_spacing,
this equals
((sector/2) >> preshift) / hash_spacing
which is the value computed by the old code.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
This is a preparation for representing also the remaining fields of struct
linear_private_data as sectors.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Rename them to num_sectors and start_sector which is more descriptive.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
conf->smallest_size is undefined since day one of the git repo..
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
'read-auto' is a variant of 'readonly' which will switch to writable
on the first write attempt.
Calling do_md_stop to set the array readonly when it is already readonly
returns an error. So make sure not to do that.
Signed-off-by: NeilBrown <neilb@suse.de>
For externally managed metadata, the 'metadata_version' sysfs
attribute is really just a channel for user-space programs to
communicate about how the array is being managed.
It can be useful for this to be changed while the array is active.
Normally changes to metadata_version are not permitted while the array
is active. Change that so that if the metadata is externally managed,
the metadata_version can be changed to a different flavour of external
management.
Signed-off-by: NeilBrown <neilb@suse.de>
Fix rdev_size_store with size == 0.
size == 0 means to use the largest size allowed by the
underlying device and is used when modifying an active array.
This fixes a regression introduced by
commit d7027458d6
Cc: <stable@kernel.org>
Signed-off-by: Chris Webb <chris@arachsys.com>
Signed-off-by: NeilBrown <neilb@suse.de>
RAID autodetect has the side effect of requiring synchronisation
of all device drivers, which can make the boot several seconds longer
(I've measured 7 on one of my laptops).... even for systems that don't
have RAID setup for the root filesystem (the only FS where this matters).
This patch makes the default for autodetect a config option; either way
the user can always override via the kernel command line.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: NeilBrown <neilb@suse.de>
Detect and report buggy drivers that destroy their request_queue.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Stefan Raspl <raspl@linux.vnet.ibm.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Publish dm_vcalloc in include/linux/device-mapper.h because this function is
used by targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Publish dm_table_unplug_all in include/linux/device-mapper.h because this
function is used by targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Publish dm_get_mapinfo in include/linux/device-mapper.h because this function
is used by targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Split struct dm_dev in two and publish the part that other targets need in
include/linux/device-mapper.h.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Don't wait between submitting crypt requests for a bio unless
we are short of memory.
There are two situations when we must split an encrypted bio:
1) there are no free pages;
2) the new bio would violate underlying device restrictions
(e.g. max hw segments).
In case (2) we do not need to wait.
Add output variable to crypt_alloc_buffer() to distinguish between
these cases.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move the initialisation of ctx->pending into one place, at the
start of crypt_convert().
Introduce crypt_finished to indicate whether or not the encryption
is finished, for use in a later patch.
No functional change.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The pending reference count must be incremented *before* the async work is
queued to another thread, not after. Otherwise there's a race if the
work completes and decrements the reference count before it gets incremented.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Make kcryptd_crypt_write_io_submit() responsible for decrementing
the pending count after an error.
Also fixes a bug in the async path that forgot to decrement it.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Make the caller reponsible for incrementing the pending count before calling
kcryptd_crypt_write_io_submit() in the non-async case to bring it into line
with the async case.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move kcryptd_crypt_write_convert_loop inside kcryptd_crypt_write_convert.
This change is needed for a later patch.
No functional change.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Factor out crypt io allocation code.
Later patches will call it from another place.
No functional change.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move io pending to one place.
No functional change, usefull to simplify debugging.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change uint32_t into chunk_t to remove 32-bit limitation on the
number of chunks on systems with 64-bit sector numbers.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move this logic to a function, because it will be reused later.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-raid1 is setting the 'DM_KCOPYD_IGNORE_ERROR' flag unconditionally
when assigning kcopyd work. kcopyd is responsible for copying an
assigned section of disk to one or more other disks. The
'DM_KCOPYD_IGNORE_ERROR' flag affects kcopyd in the following way:
When not set:
kcopyd will immediately stop the copy operation when an error is
encountered.
When set:
kcopyd will try to proceed regardless of errors and try to continue
copying any remaining amount.
Since dm-raid1 tracks regions of the address space that are (or
are not) in sync and it now has the ability to handle these
errors, we can safely enable this optimization. This optimization
is conditional on whether mirror error handling has been enabled.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch moves 'is_active' from struct dm_path to struct pgpath
as it does not need exporting.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch allows path errors from the multipath ctr function to
propagate up to userspace as errno values from the ioctl() call.
This is in response to
https://www.redhat.com/archives/dm-devel/2008-May/msg00000.html
and
https://bugzilla.redhat.com/show_bug.cgi?id=444421
The patch only lets through the errors that it needs to in order to
get the path errors from parse_path().
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Since all bio_split calls refer the same single bio_split_pool, the bio_split
function can use bio_split_pool directly instead of the mempool_t parameter;
then the mempool_t parameter can be removed from bio_split param list, and
bio_split_pool is only referred in fs/bio.c file, can be marked static.
Signed-off-by: Denis ChengRq <crquan@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...
* part_stat_*() now updates part0 together if the specified partition
is not part0. ie. part_stat_*() are now essentially all_stat_*().
* {disk|all}_stat_*() are gone.
* part_round_stats() is updated similary. It handles part0 stats
automatically and disk_round_stats() is killed.
* part_{inc|dec}_in_fligh() is implemented which automatically updates
part0 stats for parts other than part0.
* disk_map_sector_rcu() is updated to return part0 if no part matches.
Combined with the above changes, this makes NULL special case
handling in callers unnecessary.
* Separate stats show code paths for disk are collapsed into part
stats show code paths.
* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()
While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now, bdev->bd_part is set only if the bdev was for parts other
than part0. This patch makes bdev->bd_part always set so that code
paths don't have to differenciate common handling.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement {disk|part}_to_dev() and use them to access generic device
instead of directly dereferencing {disk|part}->dev. To make sure no
user is left behind, rename generic devices fields to __dev.
This is in preparation of unifying partition 0 handling with other
partitions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There are two variants of stat functions - ones prefixed with double
underbars which don't care about preemption and ones without which
disable preemption before manipulating per-cpu counters. It's unclear
whether the underbarred ones assume that preemtion is disabled on
entry as some callers don't do that.
This patch unifies diskstats access by implementing disk_stat_lock()
and disk_stat_unlock() which take care of both RCU (for partition
access) and preemption (for per-cpu counter access). diskstats access
should always be enclosed between the two functions. As such, there's
no need for the versions which disables preemption. They're removed
and double underbars ones are renamed to drop the underbars. As an
extra argument is added, there's no danger of using the old version
unconverted.
disk_stat_lock() uses get_cpu() and returns the cpu index and all
diskstat functions which access per-cpu counters now has @cpu
argument to help RT.
This change adds RCU or preemption operations at some places but also
collapses several preemption ops into one at others. Overall, the
performance difference should be negligible as all involved ops are
very lightweight per-cpu ones.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* Implement disk_devt() and part_devt() and use them to directly
access devt instead of computing it from ->major and ->first_minor.
Note that all references to ->major and ->first_minor outside of
block layer is used to determine devt of the disk (the part0) and as
->major and ->first_minor will continue to represent devt for the
disk, converting these users aren't strictly necessary. However,
convert them for consistency.
* Implement disk_max_parts() to avoid directly deferencing
genhd->minors.
* Update bdget_disk() such that it doesn't assume consecutive minor
space.
* Move devt computation from register_disk() to add_disk() and make it
the only one (all other usages use the initially determined value).
These changes clean up the code and will help disk->part dereference
fix and extended block device numbers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
raid5 can overflow with more than 255 stripes, and we can increase it
to an int for free on both 32 and 64-bit archs due to the padding.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Remove hw_segments field from struct bio and struct request. Without virtual
merge accounting they have no purpose.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Moving the path activation to workqueue along with scsi_dh patches introduced
a race. It is due to the fact that the current_pgpath (in the multipath data
structure) can be modified if changes happen in any of the paths leading to
the lun. If the changes lead to current_pgpath being set to NULL, then it
leads to the invalid access which results in the panic below.
This patch fixes that by storing the pgpath to activate in the multipath data
structure and properly protecting it.
Note that if activate_path is called twice in succession with different pgpath,
with the second one being called before the first one is done, then activate
path will be called twice for the second pgpath, which is fine.
Unable to handle kernel paging request for data at address 0x00000020
Faulting instruction address: 0xd000000000aa1844
cpu 0x1: Vector: 300 (Data Access) at [c00000006b987a80]
pc: d000000000aa1844: .activate_path+0x30/0x218 [dm_multipath]
lr: c000000000087a2c: .run_workqueue+0x114/0x204
sp: c00000006b987d00
msr: 8000000000009032
dar: 20
dsisr: 40000000
current = 0xc0000000676bb3f0
paca = 0xc0000000006f3680
pid = 2528, comm = kmpath_handlerd
enter ? for help
[c00000006b987da0] c000000000087a2c .run_workqueue+0x114/0x204
[c00000006b987e40] c000000000088b58 .worker_thread+0x120/0x144
[c00000006b987f00] c00000000008ca70 .kthread+0x78/0xc4
[c00000006b987f90] c000000000027cc8 .kernel_thread+0x4c/0x68
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If for any reason dm_merge_bvec() is given an offset beyond the end of the
device, avoid an oops and always allow one page to be added to an empty bio.
We'll reject the I/O later after the bio is submitted.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Some callers assume they can always add at least one page to an empty bio,
so dm_merge_bvec should not return 0 in this case: we'll reject the I/O
later after the bio is submitted.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When two md arrays share some block device (e.g each uses different
partitions on the one device), a resync of one array will wait for
the resync on the other to finish.
This can be a long time and as it currently waits TASK_UNINTERRUPTIBLE,
the softlockup code notices and complains.
So use TASK_INTERRUPTIBLE instead and make sure to flush signals
before calling schedule.
Signed-off-by: NeilBrown <neilb@suse.de>
A recent patch to protect the rdev list with rcu locking leaves us
with a problem because we can sleep on memalloc while holding the
rcu lock.
The rcu lock is only needed while walking the linked list as
uninteresting devices (failed or spares) can be removed at any time.
So only take the rcu lock while actually walking the linked list.
Take a refcount on the rdev during the time when we drop the lock
and do the memalloc to start IO.
When we return to the locked code, all the interesting devices
on the list will not have moved, so we can simply use
list_for_each_continue_rcu to pick up where we left off.
Signed-off-by: NeilBrown <neilb@suse.de>
When stopping an md array, or just switching to read-only, we
currently call invalidate_partition while holding the mddev lock.
The main reason for this is probably to ensure all dirty buffers
are flushed (invalidate_partition calls fsync_bdev).
However if any dirty buffers are found, it will almost certainly cause
a deadlock as starting writeout will require an update to the
superblock, and performing that updates requires taking the mddev
lock - which is already held.
This deadlock can be demonstrated by running "reboot -f -n" with
a root filesystem on md/raid, and some dirty buffers in memory.
All other calls to stop an array should already happen after a flush.
The normal sequence is to stop using the array (e.g. umount) which
will cause __blkdev_put to call sync_blockdev. Then open the
array and issue the STOP_ARRAY ioctl while the buffers are all still
clean.
So this invalidate_partition is normally a no-op, except for one case
where it will cause a deadlock.
So remove it.
This patch possibly addresses the regression recored in
http://bugzilla.kernel.org/show_bug.cgi?id=11460
and
http://bugzilla.kernel.org/show_bug.cgi?id=11452
though it isn't yet clear how it ever worked.
Signed-off-by: NeilBrown <neilb@suse.de>
If a 'repair' is requested when an array is in a position to 'recover' raid1
will perform the repair while md believes a recovery is happening. Address
this at both ends, i.e. cancel check/repair requests upon detecting a
recover condition and do not call ->spare_active after completing a
check/repair.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The raid10 resync/recovery code currently limits the amount of
in-flight resync IO to 2Meg. This was copied from raid1 where
it seems quite adequate. However for raid10, some layouts require
a bit of seeking to perform a resync, and allowing a larger buffer
size means that the seeking can be significantly reduced.
There is probably no real need to limit the amount of in-flight
IO at all. Any shortage of memory will naturally reduce the
amount of buffer space available down to a set minimum, and any
concurrent normal IO will quickly cause resync IO to back off.
The only problem would be that normal IO has to wait for all resync IO
to finish, so a very large amount of resync IO could cause unpleasant
latency when normal IO starts up.
So: increase RESYNC_DEPTH to allow 32Meg of buffer (if memory is
available) which seems to be a good amount. Also reduce the amount
of memory reserved as there is no need to keep 2Meg just for resync if
memory is tight.
Thanks to Keld for the suggestion.
Cc: Keld Jørn Simonsen <keld@dkuug.dk>
Signed-off-by: NeilBrown <neilb@suse.de>
Removing faulty devices from an array is a two stage process.
First the device is moved from being a part of the active array
to being similar to a spare device. Then it can be removed
by a request from user space.
The first step is currently not performed for read-only arrays,
so the second step can never succeed.
So allow readonly arrays to remove failed devices (which aren't
blocked).
Signed-off-by: NeilBrown <neilb@suse.de>
When we have externally managed metadata, we need to mark a failed
device as 'Blocked' and not allow any writes until that device
have been marked as faulty in the metadata and the Blocked flag has
been removed.
However it is perfectly OK to allow read requests when there is a
Blocked device, and with a readonly array, there may not be any
metadata-handler watching for blocked devices.
So in raid5/raid6 only allow a Blocked device to interfere with
Write request or resync. Read requests go through untouched.
raid1 and raid10 already differentiate between read and write
properly.
Signed-off-by: NeilBrown <neilb@suse.de>
We cannot currently change the size of a write-intent bitmap.
So if we change the size of an array which has such a bitmap, it
tries to set bits beyond the end of the bitmap.
For now, simply reject any request to change the size of an array
which has a bitmap. mdadm can remove the bitmap and add a new one
after the array has changed size.
Signed-off-by: NeilBrown <neilb@suse.de>
A recent patch allowed do_md_stop to know whether it was being called
via an ioctl or not, and thus where to allow for an extra open file
descriptor when checking if it is in use.
This broke then switch to readonly performed by the shutdown notifier,
which needs to work even when the array is still (apparently) active
(as md doesn't get told when the filesystem becomes readonly).
So restore this feature by pretending that there can be lots of
file descriptors open, but we still want do_md_stop to switch to
readonly.
Signed-off-by: NeilBrown <neilb@suse.de>
If we reduce the 'safe_mode_delay', it could still wait for the old
delay to completely expire before doing anything about safe_mode.
Thus the effect if the change is delayed.
To make the effect more immediate, run the timeout function
immediately if the delay was reduced. This may cause it to run
slightly earlier that required, but that is the safer option.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-linus' of git://neil.brown.name/md:
md: raid10: wake up frozen array
md: do not count blocked devices as spares
md: do not progress the resync process if the stripe was blocked
md: delay notification of 'active_idle' to the recovery thread
md: fix merge error
md: move async_tx_issue_pending_all outside spin_lock_irq
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
md: the bitmap code needs to use blk_plug_device_unlocked()
block: add a blk_plug_device_unlocked() that grabs the queue lock
When rescheduling a bio in raid10, we wake up
the md thread, but if the array is frozen, this
will have no effect. This causes the array to
remain frozen for eternity. We add a wake_up
to allow the array to de-freeze. This code is
nearly identical to the raid1 code, which has
this fix already.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
remove_and_add_spares() assumes that failed devices have been hot-removed
from the array. Removal is skipped in the 'blocked' case so do not count a
device in this state as 'spare'.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
handle_stripe will take no action on a stripe when waiting for userspace
to unblock the array, so do not report completed sectors.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
multipath keeps a separate device table which may be
more current than the built-in one.
So we should make sure to always call ->attach whenever
a multipath map with hardware handler is instantiated.
And we should call ->detach on removal, too.
[sekharan: update as per comments from agk]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The original STRIPE_OP_IO removal patch had the following hunk:
- for (i = conf->raid_disks; i--; ) {
+ for (i = conf->raid_disks; i--; )
set_bit(R5_Wantwrite, &sh->dev[i].flags);
- if (!test_and_set_bit(STRIPE_OP_IO, &sh->ops.pending))
- sh->ops.count++;
- }
However it appears the hunk became broken after merging:
- for (i = conf->raid_disks; i--; ) {
+ for (i = conf->raid_disks; i--; )
set_bit(R5_Wantwrite, &sh->dev[i].flags);
set_bit(R5_LOCKED, &dev->flags);
s.locked++;
- if (!test_and_set_bit(STRIPE_OP_IO, &sh->ops.pending))
- sh->ops.count++;
- }
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some dma drivers need to call spin_lock_bh in their device_issue_pending
routines. This change avoids:
WARNING: at kernel/softirq.c:136 local_bh_enable_ip+0x3a/0x85()
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-linus' of git://neil.brown.name/md: (52 commits)
md: Protect access to mddev->disks list using RCU
md: only count actual openers as access which prevent a 'stop'
md: linear: Make array_size sector-based and rename it to array_sectors.
md: Make mddev->array_size sector-based.
md: Make super_type->rdev_size_change() take sector-based sizes.
md: Fix check for overlapping devices.
md: Tidy up rdev_size_store a bit:
md: Remove some unused macros.
md: Turn rdev->sb_offset into a sector-based quantity.
md: Make calc_dev_sboffset() return a sector count.
md: Replace calc_dev_size() by calc_num_sectors().
md: Make update_size() take the number of sectors.
md: Better control of when do_md_stop is allowed to stop the array.
md: get_disk_info(): Don't convert between signed and unsigned and back.
md: Simplify restart_array().
md: alloc_disk_sb(): Return proper error value.
md: Simplify sb_equal().
md: Simplify uuid_equal().
md: sb_equal(): Fix misleading printk.
md: Fix a typo in the comment to cmd_match().
...
This patch implements biovec merge function for crypt target.
If the underlying device has merge function defined, call it.
If not, keep precomputed value.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove max_sector restriction - merge function replaced it.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch implements biovec merge function for linear target.
If the underlying device has merge function defined, call it.
If not, keep precomputed value.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce a bvec merge function for device mapper devices
for dynamic size restrictions.
This code ensures the requested biovec lies within a single
target and then calls a target-specific function to check
against any constraints imposed by underlying devices.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change snapshot per-module mempool to per-device mempool.
Per-module mempools could cause a deadlock if multiple
snapshot devices are stacked above each other.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a race condition that returns incorrect data when a write causes an
exception to be allocated whilst a read is still in flight.
The race condition happens as follows:
* A read to non-reallocated sector in the snapshot is submitted so that the
read is routed to the original device.
* A write to the original device is submitted. The write causes an exception
that reallocates the block. The write proceeds.
* The original read is dequeued and reads the wrong data.
This race can be triggered with CFQ scheduler and one thread writing and
multiple threads reading simultaneously.
(This patch relies upon the earlier dm-kcopyd-per-device.patch to avoid a
deadlock.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Whenever a snapshot read gets mapped through to the origin, track it in
a per-snapshot hash table indexed by chunk number, using memory allocated
from a new per-snapshot mempool.
We need to track these reads to avoid race conditions which will be fixed
by patches that follow.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Return a specific error message if there are an invalid number of multipath
arguments.
This invalid command returns an "Unknown error" because the ti->error field is
not set
dmsetup create --table '0 2 multipath 0 0 1 1 round-robin 0 1 1 /dev/sdh' mpath0
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm_dirty_log_{init,exit}() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Free path selector if the arguments are invalid.
This command (note that it is invalid) causes reference leak on module
"dm_round_robin" and prevents the module from being removed.
dmsetup create --table '0 2 multipath 0 0 1 1 round-robin /dev/sdh' mpath0
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
All modifications and most access to the mddev->disks list are made
under the reconfig_mutex lock. However there are three places where
the list is walked without any locking. If a reconfig happens at this
time, havoc (and oops) can ensue.
So use RCU to protect these accesses:
- wrap them in rcu_read_{,un}lock()
- use list_for_each_entry_rcu
- add to the list with list_add_rcu
- delete from the list with list_del_rcu
- delay the 'free' with call_rcu rather than schedule_work
Note that export_rdev did a list_del_init on this list. In almost all
cases the entry was not in the list anymore so it was a no-op and so
safe. It is no longer safe as after list_del_rcu we may not touch
the list_head.
An audit shows that export_rdev is called:
- after unbind_rdev_from_array, in which case the delete has
already been done,
- after bind_rdev_to_array fails, in which case the delete isn't needed.
- before the device has been put on a list at all (e.g. in
add_new_disk where reading the superblock fails).
- and in autorun devices after a failure when the device is on a
different list.
So remove the list_del_init call from export_rdev, and add it back
immediately before the called to export_rdev for that last case.
Note also that ->same_set is sometimes used for lists other than
mddev->list (e.g. candidates). In these cases rcu is not needed.
Signed-off-by: NeilBrown <neilb@suse.de>
Open isn't the only thing that increments ->active. e.g. reading
/proc/mdstat will increment it briefly. So to avoid false positives
in testing for concurrent access, introduce a new counter that counts
just the number of times the md device it open.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the array_size field of struct mddev_s to array_sectors
and converts all instances to use units of 512 byte sectors instead of 1k
blocks.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Also, change the type of the size parameter from unsigned long long to
sector_t and rename it to num_sectors.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The checks in overlaps() expect all parameters either in block-based
or sector-based quantities. However, its single caller passes two
rdev->data_offset arguments as well as two rdev->size arguments, the
former being sector counts while the latter are measured in 1K blocks.
This could cause rdev_size_store() to accept an invalid size from user
space. Fix it by passing only sector-based quantities to overlaps().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
- used strict_strtoull in place of simple_strtoull
- use my_mddev in place of rdev->mddev (they have the same value)
and more significantly,
- don't adjust mddev->size to fit, rather reject changes which make
rdev->size smaller than mddev->size
Adjusting mddev->size is a hangover from bind_rdev_to_array which
does a similar thing. But it really is a better design to insist that
mddev->size is set as required, then the rdev->sizes are set to allow
for that. The previous way invites confusion.
Signed-off-by: NeilBrown <neilb@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (102 commits)
[SCSI] scsi_dh: fix kconfig related build errors
[SCSI] sym53c8xx: Fix bogus sym_que_entry re-implementation of container_of
[SCSI] scsi_cmnd.h: remove double inclusion of linux/blkdev.h
[SCSI] make struct scsi_{host,target}_type static
[SCSI] fix locking in host use of blk_plug_device()
[SCSI] zfcp: Cleanup external header file
[SCSI] zfcp: Cleanup code in zfcp_erp.c
[SCSI] zfcp: zfcp_fsf cleanup.
[SCSI] zfcp: consolidate sysfs things into one file.
[SCSI] zfcp: Cleanup of code in zfcp_aux.c
[SCSI] zfcp: Cleanup of code in zfcp_scsi.c
[SCSI] zfcp: Move status accessors from zfcp to SCSI include file.
[SCSI] zfcp: Small QDIO cleanups
[SCSI] zfcp: Adapter reopen for large number of unsolicited status
[SCSI] zfcp: Fix error checking for ELS ADISC requests
[SCSI] zfcp: wait until adapter is finished with ERP during auto-port
[SCSI] ibmvfc: IBM Power Virtual Fibre Channel Adapter Client Driver
[SCSI] sg: Add target reset support
[SCSI] lib: Add support for the T10 (SCSI) Data Integrity Field CRC
[SCSI] sd: Move scsi_disk() accessor function to sd.h
...
Do not automatically "select" SCSI_DH for dm-multipath. If SCSI_DH
doesn't exist,just do not allow hardware handlers to be used.
Handle SCSI_DH being a module also. Make sure it doesn't allow DM_MULTIPATH
to be compiled in when SCSI_DH is a module.
[jejb: added comment for Kconfig syntax]
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (37 commits)
splice: fix generic_file_splice_read() race with page invalidation
ramfs: enable splice write
drivers/block/pktcdvd.c: avoid useless memset
cdrom: revert commit 22a9189 (cdrom: use kmalloced buffers instead of buffers on stack)
scsi: sr avoids useless buffer allocation
block: blk_rq_map_kern uses the bounce buffers for stack buffers
block: add blk_queue_update_dma_pad
DAC960: push down BKL
pktcdvd: push BKL down into driver
paride: push ioctl down into driver
block: use get_unaligned_* helpers
block: extend queue_flag bitops
block: request_module(): use format string
Add bvec_merge_data to handle stacked devices and ->merge_bvec()
block: integrity flags can't use bit ops on unsigned short
cmdfilter: extend default read filter
sg: fix odd style (extra parenthesis) introduced by cmd filter patch
block: add bounce support to blk_rq_map_user_iov
cfq-iosched: get rid of enable_idle being unused warning
allow userspace to modify scsi command filter on per device basis
...
Rename it to sb_start to make sure all users have been converted.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
As BLOCK_SIZE_BITS is 10 and
MD_NEW_SIZE_SECTORS(2 * x) = 2 * NEW_SIZE_BLOCKS(x),
the return value of calc_dev_sboffset() doubles. Fix up all three
callers accordingly.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Number of sectors is the preferred unit for sizes of raid devices,
so change calc_dev_size() so that it returns this unit instead of
the number of 1K blocks.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Changing the internal representations of sizes of raid devices
from 1K blocks to sector counts (512B units) is desirable because
it allows to get rid of many divisions/multiplications and unnecessary
casts that are present in the current code.
This patch is a first step in this direction. It replaces the old
1K-based "size" argument of update_size() by "num_sectors" and
fixes up its two callers.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
do_md_stop check the number of active users before allowing the array
to be stopped.
Two problems:
1/ it assumes the request is coming through an open file descriptor
(via ioctl) so it allows for that. This is not always the case.
2/ it doesn't do the check it the array hasn't been activated.
This is not good for cases when we use an inactive array to hold
some devices in a container.
Signed-off-by: Neil Brown <neilb@suse.de>
The current code copies a signed int from user space, converts it to
unsigned and passes the unsigned value to find_rdev_nr() which expects
a signed value. Simply pass the signed value from user space directly.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
If alloc_page() fails, ENOMEM is a more suitable error value
than EINVAL.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
The only caller of sb_equal() tests the return value against
zero, so it's OK to return the negated return value of memcmp().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Remove the dubious attempt to prefer 'compute' over 'read'. Not only is it
wrong given commit c337869d (md: do not compute parity unless it is on a failed
drive), but it can trigger a BUG_ON in handle_parity_checks5().
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
- Remove superfluous parentheses.
- Make format string match the type of the variable that is printed.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
In case pers->run() succeeds but creating the bitmap fails, we
print an error message stating that pers->run() has failed.
Print this message only if pers->run() really failed.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
