Fix below build warning and properly set bt_reset pin.
CC arch/arm/mach-pxa/cm-x300.o
arch/arm/mach-pxa/cm-x300.c: In function 'cm_x300_init_wi2wi':
arch/arm/mach-pxa/cm-x300.c:779: warning: unused variable 'wlan_en'
arch/arm/mach-pxa/cm-x300.c:795: warning: 'bt_reset' may be used uninitialized in this function
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: <stable@kernel.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
GuruPlugD was initially named to be SHEEVAD, and it's causing naming
confusion in the mach-types database. Make it consistent by renaming
to GPLUGD.
Reported-and-Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Noticed when setting SSP0 in clk_set_rate, _CLK_SET_RATE attempts to
reset the clock divider for the SSP0 parent clock, in this case
IO0FRAC. Bits 24-29 of HW_CLKCTRL_FRAC0 are cleared correctly, but
when the new frac value is written the value isn't shifted up to write
the correct bit-field. This results in IO0FRAC being set to 0 and
CPUFRAC being corrupted.
This should occur when writing IO1FRAC, EMIFRAC in HW_CLKCTRL_FRAC0
and GPMIFRAC, HSADCFRAC in HW_CLKCTRL_FRAC1.
Tested on custom i.MX28 board with SSP0 SPI driver.
Signed-off-by: Matt Burtch <matt@grid-net.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To configure pads during the initialisation a set of special constants
is used, e.g.
#define MX25_PAD_FEC_MDIO__FEC_MDIO IOMUX_PAD(0x3c4, 0x1cc, 0x10, 0, 0, PAD_CTL_HYS | PAD_CTL_PUS_22K_UP)
The problem is that no pull-up/down is getting activated unless both
PAD_CTL_PUE (pull-up enable) and PAD_CTL_PKE (pull/keeper module
enable) set. This is clearly stated in the i.MX25 datasheet and is
confirmed by the measurements on hardware. This leads to some rather
hard to understand bugs such as misdetecting an absent ethernet PHY (a
real bug i had), unstable data transfer etc. This might affect mx25,
mx35, mx50, mx51 and mx53 SoCs.
It's reasonable to expect that if the pullup value is specified, the
intention was to have it actually active, so we implicitly add the
needed bits.
Cc: stable@kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This tries to clear up the confusion between integers and iomem pointers
in the marvell pxa platform. MMIO addresses are supposed to be __iomem*
values, in order to let the Linux type checking work correctly. This
patch moves the cast to __iomem as far back as possible, to the place
where the MMIO virtual address windows are defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The sharpsl code selects the max1111 spi driver, so it must also
ensure that SPI itself is enabled. The platform does not work
without max1111.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The two platforms are part of the palm27x family and use the same
code. Select the palm27x symbol to make sure they can be built
standalone.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The raumfeld platform code calls power_supply_set_battery_charged
which is part of the power supply layer, so that always has
to be enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
We cannot support ARMv5 and ARMv7 based boards in a single kernel,
so introduce a new option in mach-pxa to select between the two.
The PJ4 (ARMv7) based boards are now only visible when
CONFIG_ARCH_PXA_V7 is set, the other boards are only visible
when it's not set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The pxa specific cpufreq code is based on the cpu_freq_table
module, so we have to select that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
saarb uses pxa3xx_map_io and pxa3xx_handle_irq, which are part
of the pxa3xx code. This makes sure the necessary header and
implementation is used when building the board file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
There are two variants of the palmtreo machine, the 680 and the
centro, and Kconfig allows selecting one or both of them.
This changes the board file so that it's actually possible
to build all configurations that are allowed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The pxa3xx_u2d_start_hc/pxa3xx_u2d_stop_hc symbols are used by the
ohci-pxa27x driver, which can be a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
When support for zylonite is disabled, the zylonite_pxa300_init
and zylonite_pxa320_init functions are not there, but the declaration
is still kept around if any other boards for the same soc are
enabled. This changes the declaration to be conditional on the
same symbol as the code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Defconfig file for at91sam9g45 SoC family:
at91sam9g45, at91sam9g46, at91sam9m10, at91sam9m11.
The Atmel Evaluation Kit for this family is the at91sam9m10g45ek.
It is so useful for automatic compile tests...
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This applies ARM errata fix 754322 for all ux500 platforms.
Cc: stable@kernel.org
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes bug where variable i was redundantly used for counting two nested loops.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
`keypad_pads' is referred to by `keypad_data' which is
not __initdata, so `keypad_pads' should not be __initdata either.
Signed-off-by: Bjarne Steinsbo <bsteinsbo@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the PXA
GPIO driver down to the GPIO subsystem so it can be consolidated.
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Ryan Mallon <rmallon@gmail.com>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current code calls omap4430_phy_init() twice in usb_musb_init().
Calling omap4430_phy_init() once is enough.
This patch removes the first omap4430_phy_init() call, which using an
uninitialized pointer as parameter.
This patch elimates below build warning:
arch/arm/mach-omap2/usb-musb.c: In function 'usb_musb_init':
arch/arm/mach-omap2/usb-musb.c:141: warning: 'dev' may be used uninitialized in this function
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Bjarne Steinsbo <bsteinsbo@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like 2600 kHz rate does not work reliably on 2430,
so just use the 100 kHz rate.
Otherwise the system often fails to boot properly with:
omap_i2c omap_i2c.2: timeout waiting for bus ready
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
twl: clock init err [-110]
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
TWL4030 Unable to unlock IDCODE registers --110
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP4_USBC1_ICUSB_PWRDNZ_MASK during enable/disable PWRDNZ mode for
MMC1_PBIAS and associated extended-drain MMC1 I/O cell. This is in accordance
with the control module programming guide. This fixes a bug where if trying to
use gpio_98 or gpio_99 and MMC1 at the same time the GPIO signal will be
affected by a changing SDMMC1_VDDS.
Software must keep MMC1_PBIAS cell and MMC1_IO cell PWRDNZ signals low whenever
SDMMC1_VDDS ramps up/down or changes for cell protection purposes.
MMC1 is based on SDMMC1_VDDS whereas USBC1 is based on SIM_VDDS therefore
they can operate independently.
Signed-off-by: Bryan Buckley <bryan.buckley@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This will eventually allow <mach/gpio.h> to be deleted. This mirrors
LinusW's recent equivalent work on various other ARM platforms.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sclk_cam clocks are now controlled by the top level FIMC media
device driver bound to "s5p-fimc-md" platform device.
Rename sclk_cam clocks so they accessible by the corresponding
driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sclk_cam clocks are now controlled by the top level FIMC media
device driver bound to "s5p-fimc-md" platform device.
Rename sclk_cam clocks so they accessible by the corresponding
driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7099/1: futex: preserve oldval in SMP __futex_atomic_op
ARM: dma-mapping: free allocated page if unable to map
ARM: fix vmlinux.lds.S discarding sections
ARM: nommu: fix warning with checksyscalls.sh
ARM: 7091/1: errata: D-cache line maintenance operation by MVA may not succeed
The SMP implementation of __futex_atomic_op clobbers oldval with the
status flag from the exclusive store. This causes it to always read as
zero when performing the FUTEX_OP_CMP_* operation.
This patch updates the ARM __futex_atomic_op implementations to take a
tmp argument, allowing us to store the strex status flag without
overwriting the register containing oldval.
Cc: stable@kernel.org
Reported-by: Minho Ban <mhban@samsung.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This centralizes all GPIO naming in one header.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the attempt to map a page for DMA fails (eg, because we're out of
mapping space) then we must not hold on to the page we allocated for
DMA - doing so will result in a memory leak.
Cc: <stable@kernel.org>
Reported-by: Bryan Phillippe <bp@darkforest.org>
Tested-by: Bryan Phillippe <bp@darkforest.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Loop iterator value after terminating list_for_each_entry()
is not NULL. This patch fixes incorrect iterator usage in
GPIO interrupt code for SAMSUNG S5P platforms.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The changed statement should set the old armdiv bits to 0
and not everything else, before setting the new value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
For Seaboard's internal eMMC, this makes the difference between a
5.5MB/s and 10.2MB/s transfer rate. On Harmony, there wasn't any
measurable difference on my cheap/slow ~2MB/s card.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Apparently U8500 U-Boot versions may leave the l2x0 locked down
before executing the kernel. Make sure we unlock it before we
initialize the l2x0. This fixes a performance problem reported
by Jan Rinze.
The l2x0 core has been modified to unlock the l2x0 by default,
but it will not touch the locking registers if the l2x0 was
already enabled, as on the ux500, so we need this quirk to
make sure it is properly turned off.
Cc: stable@kernel.org
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Adrian Bunk <adrian.bunk@movial.com>
Reported-by: Jan Rinze <janrinze@gmail.com>
Tested-by: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This applies ARM errata fix 754322 for all ux500 platforms.
Cc: stable@kernel.org
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are seeing linker errors caused by sections being discarded, despite
the linker script trying to keep them. The result is (eg):
`.exit.text' referenced in section `.alt.smp.init' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
`.exit.text' referenced in section `.alt.smp.init' of net/built-in.o: defined in discarded section `.exit.text' of net/built-in.o
This is the relevent part of the linker script (reformatted to make it
clearer):
| SECTIONS
| {
| /*
| * unwind exit sections must be discarded before the rest of the
| * unwind sections get included.
| */
| /DISCARD/ : {
| *(.ARM.exidx.exit.text)
| *(.ARM.extab.exit.text)
| }
| ...
| .exit.text : {
| *(.exit.text)
| *(.memexit.text)
| }
| ...
| /DISCARD/ : {
| *(.exit.text)
| *(.memexit.text)
| *(.exit.data)
| *(.memexit.data)
| *(.memexit.rodata)
| *(.exitcall.exit)
| *(.discard)
| *(.discard.*)
| }
| }
Now, this is what the linker manual says about discarded output sections:
| The special output section name `/DISCARD/' may be used to discard
| input sections. Any input sections which are assigned to an output
| section named `/DISCARD/' are not included in the output file.
No questions, no exceptions. It doesn't say "unless they are listed
before the /DISCARD/ section." Now, this is what asn-generic/vmlinux.lds.S
says:
| /*
| * Default discarded sections.
| *
| * Some archs want to discard exit text/data at runtime rather than
| * link time due to cross-section references such as alt instructions,
| * bug table, eh_frame, etc. DISCARDS must be the last of output
| * section definitions so that such archs put those in earlier section
| * definitions.
| */
And guess what - the list _always_ includes .exit.text etc.
Now, what's actually happening is that the linker is reading the script,
and it finds the first /DISCARD/ output section at the beginning of the
script. It continues reading the script, and finds the 'DISCARD' macro
at the end, which having been postprocessed results in another
/DISCARD/ output section. As the linker already contains the earlier
/DISCARD/ output section, it adds it to that existing section, so it
effectively is placed at the start. This can be seen by using the -M
option to ld:
| Linker script and memory map
|
| 0xc037c080 jiffies = jiffies_64
|
| /DISCARD/
| *(.ARM.exidx.exit.text)
| *(.ARM.extab.exit.text)
| *(.exit.text)
| *(.memexit.text)
| *(.exit.data)
| *(.memexit.data)
| *(.memexit.rodata)
| *(.exitcall.exit)
| *(.discard)
| *(.discard.*)
|
| 0xc0008000 . = 0xc0008000
|
| .head.text 0xc0008000 0x1d0
| 0xc0008000 _text = .
| *(.head.text)
| .head.text 0xc0008000 0x1d0 arch/arm/kernel/head.o
| 0xc0008000 stext
|
| .text 0xc0008200 0x2d78d0
| 0xc0008200 _stext = .
| 0xc0008200 __exception_text_start = .
| *(.exception.text)
| .exception.text
| ...
As you can see, all the discarded sections are grouped together - and
as a result of it being the first output section, they all appear before
any other section.
The result is that not only is the unwind information discarded (as
intended), but also the .exit.text, despite us wanting to have the
.exit.text preserved.
We can't move the unwind information elsewhere, because it'll then be
included even when we do actually discard the .exit.text (and similar)
sections.
So, work around this by avoiding the generic DISCARDS macro, and instead
conditionalize the sections to be discarded ourselves. This avoids the
ambiguity in how the linker assigns input sections to output sections,
making our script less dependent on undocumented linker behaviour.
Reported-by: Rob Herring <robherring2@gmail.com>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
