Fix a subtle race condition between tg3_start_xmit() and tg3_tx()
discovered by Herbert Xu <herbert@gondor.apana.org.au>:
CPU0 CPU1
tg3_start_xmit()
if (tx_ring_full) {
tx_lock
tg3_tx()
if (!netif_queue_stopped)
netif_stop_queue()
if (!tx_ring_full)
update_tx_ring
netif_wake_queue()
tx_unlock
}
Even though tx_ring is updated before the if statement in tg3_tx() in
program order, it can be re-ordered by the CPU as shown above. This
scenario can cause the tx queue to be stopped forever if tg3_tx() has
just freed up the entire tx_ring. The possibility of this happening
should be very rare though.
The following changes are made:
1. Add memory barrier to fix the above race condition.
2. Eliminate the private tx_lock altogether and rely solely on
netif_tx_lock. This eliminates one spinlock in tg3_start_xmit()
when the ring is full.
3. Because of 2, use netif_tx_lock in tg3_tx() before calling
netif_wake_queue().
4. Change TX_BUFFS_AVAIL to an inline function with a memory barrier.
Herbert and David suggested using the memory barrier instead of
volatile.
5. Check for the full wake queue condition before getting
netif_tx_lock in tg3_tx(). This reduces the number of unnecessary
spinlocks when the tx ring is full in a steady-state condition.
6. Update version to 3.65.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All caller of netdev_alloc_skb need to assign skb->dev shortly
afterwards. Move it into common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove system device class for xpram. It creates the directory hierarchy
under /sys/devices/system/xpram/xpram0. The xpram0 directory is empty and
it is always created while xpram1 and following devices are always missing,
independent if the devices exist or not. Since the xpram devices are
listed in /proc/partitions and /sys/block/ as slram<x> the system device
class for xpram is meaningless.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I/O on a CCW device may stall if a channel path to that device is
logicaly varied off/on. A user I/O interrupt can get misinterpreted
as interrupt for an internal path verification operation due to a
missing check and is therefore never reported to the device driver.
Correct check for pending interruptions before starting path
verification.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do a retry of read device characteristics / read configuration
data when a deferred condition code 1 is encountered in
ccw_device_wake_up().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Without this patch register_tape_dev() will always fail, but might
return a value that is not an error number. This will lead to accesses
to already freed memory areas...
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Another misuse of the global 'io' variable instead of the local 'base'.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch corrects a problem in mptfc which can result in targets
being removed after executing an "lsiutil 99" reset of the fibre
channel ports.
The last rescan event was being processed before the setup reset work
due to an inappropriate optimization in the event processing logic.
Every rescan event is now queued for execution and the setup reset
work now executes in the proper sequence.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Based upon a conversation I had with LSI's fibre channel firmware guru,
this patch adds another condition under which the driver waits for the
firmware link initialization / target discovery to complete.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There were some confusion about base I/O variables in the wbsd driver.
Seems like things have been working on shear luck so far. The global 'io'
variable (used when manually configuring the resources) was used instead of
the local 'base' variable.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SCSI folk forgot to fix up all the uses of 'buffer' before deleting
this struct member. Do it for them to rescue the resulting build
failures.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The hptiop just got merged with a horrible amount of really bad ioctl
code that is against the standards for new scsi drivers. This patch
backs it out (and fixes a small bug where scsi_add_host is called to
early). We can re-add proper APIs once we agree on them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
arch/ia64/hp/sim/simscsi.c
Stylistic differences in two separate fixes for buffer->request_buffer
problem.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug fixes for zfcp's erp:
- trigger adapter reopen if do_QDIO fails
- avoid erp deadlock if registration of scsi target or remote port hang
- do not treat as error if exchange port data fails
- decrease timeout for target reset and aborts
- mark unit failed if slave_destroy is called
Additionally some code cleanup was done:
- made some functions void when retval is not of interest
- shortened initialization of zfcp's host_template
- corrected some comments
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve request handling. Use hash table to manage request IDs.
Signed-off-by: Volker Sameske <sameske@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently it is impossible to reset provided by Qlogic QLA2xxx driver
SCSI devices externally using corresponding sg devices, particularly via
sg_reset utility, because qla2xxx driver in qla2xxx_eh_device_reset()
function checks if the input scsi_cmnd has its private data (CMD_SP())
attached. Then the found pointer isn't used anywhere inside of
qla2xxx_eh_device_reset(). If the RESET request comes from sg device, it
doesn't have such private data.
The attached patch removes check for non-NULL CMD_SP() from
qla2xxx_eh_device_reset(), hence allows to reset QLA2xxx's devices using
corresponding sg devices.
AV: change applies to bus/host reset handlers as well.
Signed-off-by: Vladislav Bolkhovitin <vst@vlnb.net>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ID String and Message fixes
- Fix switch symbolic name registration to match cross-OS values
- Replace printk's with more standard lpfc_printf_log calls
- Make all lpfc_printf_log message numbers unique
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Short bug fixes:
- Fix iocbq list corruption due to missing list_del's in ct handling
- Missing unlock in lpfc_sli_next_iotag()
- Fix initialization of can_queue value
- Differentiate sysfs mailbox errors with different codes.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix race condition between lpfc_sli_issue_mbox and lpfc_online
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix failing firmware download due to mailbox delays needing to be longer.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
While busy-waiting for completion, check the hardware after scheduling;
don't schedule and then immediately check the _timeout_. If the yield()
took a long time (as it does on my OLPC prototype board when it's busy),
we'd report a timeout even though the hardware was now ready.
This fixes it, and also switches the yield() for a cond_resched() because
we don't actually want to be _that_ nice about it. I see nice
tightly-packed SMBus transactions now, rather than waiting for milliseconds
between successive phases.
Actually, we shouldn't be busy-waiting here at all. We should be using
interrupts. That's an exercise for another day though.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Christer Weinigel <wingel@nano-system.com>
Cc: <Jordan.Crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A patch in -mm kernel correct the parsing of "address resources" of pnpacpi.
Before we assumed it was memory only, but it could be also IO.
But this change show an hidden bug : some resources could be producer type
that are not handled by pnp layer. So we should ignore the producer
resources.
This patch fixes bug 6292 (http://bugzilla.kernel.org/show_bug.cgi?id=6292).
Some devices like PNP0A03 have 0xd00-0xffff and 0x0-0xcf7 as IO producer
resources.
Before correcting "address resources" parsing, it was seen as memory and was
harmless, because nobody tried to reserve this memory range as it should be
IO.
With the correction it become IO resources, and make failed all others device
that want to register IO in this range and use pnp layer (like a ISA sound
card).
The solution is to ignore producer resources
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: "Brown, Len" <len.brown@intel.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
both of acpi_memory_enable_device() and acpi_memory_add_device() may evaluate
_CRS method.
We should avoid evaluate device's resource twice if we could get it
successfully in past.
Signed-off-by: KAMEZWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add_memory() does all necessary check to avoid collision. then, acpi layer
doesn't have to check region by itself.
(*) pfn_valid() just returns page struct is valid or not. It returns 0
if a section has been already added even is ioresource is not added.
ioresource collision check in mm/memory_hotplug.c can do more precise
collistion check.
added enabled bit check just for sanity check..
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At least Maxtor OneTouch III require a "start stop unit" command after auto
spin-down before the next access can proceed. This patch activates the
responsible code in scsi_mod for all Maxtor SBP-2 disks.
https://bugzilla.novell.com/show_bug.cgi?id=183011
Maybe that should be done for all SBP-2 disks, but better be cautious.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* MODE_MASK is unused in eicon driver.
* Conflicts with a ptrace stuff on arm.
drivers/isdn/hardware/eicon/divasync.h:259:1: warning: "MODE_MASK" redefined
include2/asm/ptrace.h:48:1: warning: this is the location of the previous definition
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Acked-by: Armin Schindler <armin@melware.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A set of tty line discipline cleanup patches were introduced before the
dawn of time, in kernel version 2.4.21. This patch performs that cleanup
for the hvsi driver.
The hvsi driver is used only on IBM pSeries PowerPC boxes. The driver was
originally written by Hollis Blanchard, who has delegated maintainership to
me. So this my first and maybe only patch in this official new role,
because this driver is otherwise bug-free :-)
Alan: "Actually its also a bug fix, tty->ldisc should be locked by refcounting
and the helpers do this for you."
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Under certain rare circumstances, it appears that there can be be a
NULL-pointer deref when a user fiddles with terminal emeulation programs while
outpu is being sent to the console. This patch checks for and avoids a
NULL-pointer deref.
Signed-off-by: Hollis Blanchard <hollisbl@austin.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix up the start up sequence.
This new sequence allow you to correctly enable the LCD controller
even if the bootloader has already did it.
- fix up a wrong indentation issue.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix "info->var.rotate" data settings.
This info should be deduced directly from "fbdev->panel->control_base"
defined into au1100fb.h.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent patch that allowed linear arrays to be reconfigured on-line
allowed in a bug which results in divide by zero - not all
mddev->array_size were converted to conf->array_size.
This patch finished the conversion and fixed the bug.
The offending patch was commit 7c7546ccf6.
Thanks to Simon Kirby <sim@netnation.com> for the bug report.
Cc: Simon Kirby <sim@netnation.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Seems like the omap-rng driver in the main tree predates the switch from
<asm/hardware/clock.h> to <linux/clk.h> ... now it builds OK.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current Linus tree crashes in aty128_set_lcd_enable() because par->pdev
is NULL. This happens since at least a week. Call trace is:
aty128_set_lcd_enable
aty128fb_set_par
fbcon_init
visual_init
take_over_console
fbcon_takeover
notifier_call_chain
blocking_notifier_call_chain
register_framebuffer
aty128fb_probe
pci_device_probe
bus_for_each_dev
driver_attach
bus_add_driver
driver_register
__pci_register_driver
aty128fb_init
init
kernel_thread
- info->fix was assigned twice.
- par->vram_size is assigned in aty128_probe(), no need to redo it again
in aty128_init()
- register_framebuffer() uses uninitialized struct members, move it past
par->pdev assignment and past aty128_bl_init().
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CONFIG_PCI=n:
CC drivers/edac/edac_mc.o
drivers/edac/edac_mc.c: In function âadd_mc_to_global_listâ:
drivers/edac/edac_mc.c:1362: error: implicit declaration of function âto_platform_deviceâ
drivers/edac/edac_mc.c:1362: error: invalid type argument of â->â
drivers/edac/edac_mc.c: In function âedac_mc_add_mcâ:
drivers/edac/edac_mc.c:1467: error: invalid type argument of â->â
drivers/edac/edac_mc.c: In function âedac_mc_del_mcâ:
drivers/edac/edac_mc.c:1504: error: invalid type argument of â->â
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Juha [l
When the block queue is plugged, mq->req must be set to NULL.
Otherwise mq->req might be left non-NULL, even though mmcqd is
not processing a request, thus preventing the MMC queue thread from
being woken up when new requests do arrive.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By using milliseconds instead of jiffies to calculate acceleration
factor we make the code immune to changes in HZ.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When emulating button toggle drivers need to send input_sync()
between 'down' and 'up' events, otherwise some users might miss
keypress because device's state is only considered finalized
after EV_SYN/SYN_REPORT is received.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Trackpoint driver was not sending the magic knock sequence upon resume
causing incorrect device behavior after resuming from disk.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
MX300 does not have an EXTRA_BTN - it is a simple wheel mouse with
an additional task-switcher button, which is reported as side button
(and not task button).
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In the error path, ata_device_add()
* dereferences null host_set->ports[] element.
* calls scsi_remove_host() on not-yet-added shost.
This patch fixes both bugs. The first problem was spotted and initial
patch submitted by Dave Jones <davej@redhat.com>. The second problem
was mentioned and fixed by Jeff Garzik <jgarzik@pobox.com> in a larger
cleanup patch.
Cc: Dave Jones <davej@redhat.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24 doesn't make use of probe_ent->mmio_base and setting this
field causes the area to be released twice on detach. Don't set
probe_ent->mmio_base.
Signed-off-by: Tejun Heo <htejun@gmail.com>
To get host_set->private_data initialized reliably, all pinfos need to
point to the same hpriv. Restore pinfo->private_data after pata pinfo
assignment.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_prot_detach() did nothing for old EH ports and thus SCSI hosts
associated with those ports are left dangling after they are detached
leaving stale devices and causing oops eventually. Make
ata_port_detach() remove SCSI hosts for old EH ports.
Signed-off-by: Tejun Heo <htejun@gmail.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Propagate acpi_processor_preregister_performance return value.
[CPUFREQ] [2/2] demand load governor modules.
[CPUFREQ] [1/2] add __find_governor helper and clean up some error handling.
[CPUFREQ] Longhaul - Rename & fix multipliers table
[CPUFREQ] Longhaul - Fix power state test to do something more useful
[CPUFREQ] Longhaul - Readd accidentally dropped line
[CPUFREQ] Make longhaul_walk_callback() static
[CPUFREQ] X86_GX_SUSPMOD must depend on PCI
[CPUFREQ] Longhaul - Initialise later.
[CPUFREQ] Longhaul - Workaround issues with APIC.
[CPUFREQ] Longhaul - Hook into ACPI C states.
[CPUFREQ] return error when failing to set minfreq
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] ahci: skip protocol test altogether in spurious interrupt code
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PNP: Add missing casts in printk() arguments
PCI: docking station: remove dock uevents
PCI: Unhide the SMBus on Asus PU-DLS
PCI Hotplug: add acpiphp to MAINTAINERS
PCI: pci/search: EXPORTs cannot be __devinit
PCIE: cleanup on probe error
pcie: fix warnings when CONFIG_PM=n
Skip protocol test altogether in spurious interrupt code. If PIOS is received
when it shouldn't, ahci will raise protocol violation.
Signed-off-by: Unicorn Chang <uchang@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When writing the firmware to the NIC, the FIFO is 256-bytes long,
so we use 256-bytes chunks and a read to wait until the previous
write is done.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent phylib from freeing PHY IRQ twice on closing an eth device:
phy_disconnect() first calls phy_stop_interrupts(), then it calls
phy_stop_machine() which in turn calls phy_stop_interrupts() making the
kernel complain on each bootup...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains some of the bug fixes and enhancements done to
s2io driver. Following are the brief description of changes
1. code cleanup to handle gso modification better
2. Move repeated code in rx path, to a common function
s2io_chk_rx_buffers()
3. Bug fix in MSI interrupt
4. clear statistics when card is down
5. Avoid linked list traversing in lro aggregation.
6. Use pci_dma_sync_single_for_cpu for buffer0 in case of 2/3
buffer mode.
7. ethtool tso get/set functions to set clear NETIF_F_TSO6
8. Stop LRO aggregation when we receive ECN notification
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains some of the bug fixes and enhancements done to
s2io driver. Following are the brief description of changes
1. Introduced macro "S2IO_PARM_INT" for declaring integer load parameter
2. UDP_RR test failure, memset txdl after Tx completion
3. PXE boot may leave adapter in unknown state so do reset in probe.
4. Add Tx completion code in netpoll
5. In s2io_vpd_read() move array vpd_data[] to pointer, saves stack memory
6. Fix bug in ethtool online test
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some resource_size_t values are fed to printk() without handling the fact
that they can have different size depending on your .config.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove uevent dock notifications. There are no consumers
of these events at present, and uevents are likely not the
correct way to send this type of event anyway.
Until I get some kind of idea if anyone in userspace cares
about dock events, I will just not send any.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unhide the SMBus controller on the Asus PU-DLS board.
This fixes bug #6763.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add acpiphp to the MAINTAINERS file.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If pcie_portdrv_probe() fails but it had already called
pci_enable_device(), then call pci_disable_device() when
returning error.
Is there some reason that this isn't being done?
or was it just missed?
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wait until all users have closed their device context before allowing
device unregistration to complete. This prevents a crash caused by
referring to stale data structures.
A better solution would be to have a way to revoke contexts rather
than waiting for userspace to close the context, but that's a much
bigger change that will have to wait. For now let's at least avoid
the crash.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove references to the IPoIB IETF working group as it has been closed.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Data corruption has been seen with Mellanox SRP targets when FMRs
create a memory region with I/O virtual address != 0. Add a
workaround that disables FMR merging for Mellanox targets (OUI 0002c9).
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Protect against srp_reset_device() clearing the req_queue while
srp_reconnect_target() is in progress (note that state change at
the top of srp_reconnect_target() is not sufficient for this since
srp_reset_device() ignores the state).
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Report error code rather than success (0) on failure allocating
timewait_info in ib_send_cm_req().
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Define a constant MTHCA_ARRAY_MASK to replace repeated uses of
(PAGE_SIZE / sizeof (void *) - 1) in mthca array code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_array_clear() does not clear the slot if the used count is
positive. This leads to crashes in mthca_qp_event() since that uses
mthca_array_get() to check that the qp is valid.
Discovered by Ali Ayoub.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (24 commits)
Revert "[PATCH] USB: move usb_device_class class devices to be real devices"
Revert "[PATCH] USB: convert usb class devices to real devices"
USB: UHCI: Don't test the Short Packet Detect bit
USB: unusual_devs entry for Nokia 3250
USB: dummy-hcd: disable interrupts during req->complete
USB: fix the USB_GADGET_DUMMY_HCD dependencies
USB: ati_remote.c: autorepeat fix
USB: doc: fixes devio.c location in proc_usb_info.txt.
USB: doc: usb-help.txt update.
USB: Patch for rtl8150 to fix unplug problems
USB: cypress driver comment updates
USB: unusual_devs device removal
usb-storage: Add US_FL_IGNORE_DEVICE flag; ignore ZyXEL G220F
USB: New USB ID for Belkin Serial Adapter
USB: Additional PID for the ftdi_sio driver
USB: adding support for SHARP WS003SH to ipaq.c
USB: Fix Freescale high-speed USB host dependency
USB: Removed 3-port device handler from Option driver
USB: Drop Sierra Wireless MC8755 from the Option driver
USB: Let option driver handle Anydata CDMA modems. Remove anydata driver.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-2.6.18:
gitignore: gitignore quilt's files
kbuild: always use $(CC) for $(call cc-version)
kconfig: correct oldconfig for unset choice options
kbuild: -fno-stack-protector is not good
kbuild: fix typo in modpost
kbuild: improve error from file2alias
kbuild: .gitignore utsrelease.h
kbuild: version.h and new headers_* targets does not require a kernel config
kbuild: hardcode value of YACC&LEX for aic7-triple-x
This reverts c182274ffe commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts bd00949647 commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently some UHCI controllers change the value of the Short Packet
Detect (SPD) bit in the TD status word -- presumably when they receive a
short packet. This patch (as759) changes uhci-hcd to avoid assuming
that the bit is unchanged; in fact, the driver no longer looks at SPD at
all.
This fixes the second problem reported in Bugzilla #6752.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is another unusual_devs entry (as760) for another Nokia device,
this time the 3250.
From: Mario Rettig <mariorettig@web.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as756) fixes a bug in dummy-hcd found by the lockdep
checker. In one of the code paths, the driver did not disable
interrupts before calling a request completion routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If USB=m, USB_GADGET=y, the option USB_GADGET_DUMMY_HCD mustn't be
offered since selecting it results in a compile error.
This patch fixes kernel Bugzilla #6534 reported by Toralf Frster.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When HZ is set to 250 (new default) or 100, the time span during which
repeated events from the device are ignored could be too small due to
ms->jiffies rounding. This causes the auto repeat to kick in early making
it impossible for the user to generate individual press/release events.
Increate the timeout to compensate.
Signed-off-by: Marko Macek <Marko.Macek@gmx.net>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RTL8150 driver currently crashes the kernel if the USB lead is unplugged
while the device is active. The attached patch adds error handling to
tell the network layer that the device has gone away when the device is
unplugged. With this patch, the device can be plugged and unplugged
to one's hearts' content, without crashing anything.
Oh, I've also added rudimentary suspend and resume methods.
Signed-off-by: Peter Chubb <peter@gelato.unsw.edu.au>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This entry has been a mystery for some time. I had sent this patch as an
RFC a while ago, and now we've had two reports of this not being needed,
so I'm removing it.
In the event there are reports of breakage, we should revert this patch,
but add a US_FL_NEED_OVERRIDE flag.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new unusual_devs flag for when usb-storage needs to ignore
a device that it would otherwise claim.
We need to ignore the ZyXEL G220F as it is a virtual CDROM drive which
includes the windows driver for this USB-WLAN adapter. After the windows
driver is installed on a windows system, it converts it into a WLAN adapter
(by ejecting the virtual disc).
The virtual CDROM is of no interest to Linux users. The zd1211rw driver will
automatically perform the eject operation, we just need to ensure that
usb-storage does not claim the device.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Can you add the USB IDs for the Belkin USB Serial adapter (P/N F5U257)
to the pl2303 driver in the Linux Kernel? Are you the appropriate person
to approach for this?
I recently purchased a Belkin USB Serial adapter (P/N F5U257) and found
that it didn't work. After a bit of experimentation I found that it
works with the pl2303 driver once the ID has been added. See attached
patch to fix this. Also attached is the output from lsusb -v just in
case you require any information from there.
From: Kim Oldfield <luv@oldfield.wattle.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a short patch which adds one PID to the set of devices
supported by the ftdi_sio driver. The device in question is a
DLP module used as part of a ham radio USB-to-packet adapter.
From: Dave Platt <dplatt@radagast.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This small patch enables a support of "SHARP WS003SH".
"SHARP WS003SH" (usullary called "W-ZERO3") is most polular All-in-one handheld
CellPhone-plus-WindowsMobile5.0 in Japan.
"SHARP WS003SH" has two modes, "Modem" and "ActiveSync".
But, "ActiveSync" mode uses NDIS connection.
Therefore, ipaq.c can only support "Modem" mode.
http://www.sharp.co.jp/ws/ (Japanese Site)
http://greggman.com/edit/editheadlines/2005-12-24.htm
From: Norihiko Tomiyama <norihiko.tomiyama@ctc-g.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The high-speed USB SOC only exists on MPC834x family not MPC83xx family.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The short driver names were not unique,
which prevented the driver from actually loading.
Also, one of the ioctl pointers was missing.
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OHCI updates for AT91 series processors:
- Get ready for at91sam926x processors (ARMv5tej not ARMv4t)
- Suspend/resume support now behaves properly
- In "standby" mode, OHCI can be a source of system wakeup events
(remote wakeup, device connect/disconnect, etc)
And minor cleanups.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UDC updates for AT91 series processors:
- Get ready for at91sam926x processors (ARMv5tej not ARMv4t)
- Suspend/resume support now behaves properly
- In "standby" mode, UDC can be a source of system wakeup events
(host resume, device connect/disconnect, etc)
- Fix IRQ storming issues, seemingly related to clock disabling
changes that went in a while back
And minor cleanups, especially whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a platform check to the snsc driver init function, to prevent
loading on non-sn2 systems.
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we allow building appletalk drivers in-kernel when
CONFIG_ATALK is modular. That doesn't work because these drivers use
symbols such as "alloc_talkdev" which is exported from code built
by CONFIG_ATALK.
Noticed by Toralf Förster.
Signed-off-by: David S. Miller <davem@davemloft.net>
I had problems with my AVM Fritz!Box access point. It appeared
that the AP deauthorized me and the softmac didn't reconnect me.
This patch handles the problem.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Discovered a problem while accessing www.python.org on my PPC32.
The problem was pretty consistent for all sticks. The reason was
that while testing for the length info tag, I ignored the
endianess of the host system.
Please recognize that converting the constant to little endian, we
create faster code.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is never called in interrupt context, and it doesn't
matter if it is called in IRQ context or not.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apparently the ZD1211 doesn't mind, but the ZD1211B absolutely must be
told that encryption is happening in software.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We'll be needing these at some point...
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There has been a problem in the radiotap header. Monitor mode
works now with tcpdump 3.94 + libpcap 0.9.4. ethereal 0.99.0 +
libpcap 0.9.4 is broken, because it doesn't find the right offset
for the IEEE 802.11 header.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (26 commits)
V4L/DVB (4380): Bttv: Revert VBI_OFFSET to previous value, it works better
V4L/DVB (4379): Videodev: Check return value of class_device_register() correctly
V4L/DVB (4373): Correctly handle sysfs error leg file removal in pvrusb2
V4L/DVB (4368): Bttv: use class_device_create_file and handle errors
V4L/DVB (4367): Videodev: Handle class_device related errors
V4L/DVB (4365): OVERLAY flag were enabled by mistake
V4L/DVB (4344): Fix broken dependencies on media Kconfig
V4L/DVB (4343): Fix for compilation without V4L1 or V4L1_COMPAT
V4L/DVB (4342): Fix ext_controls align on 64 bit architectures
V4L/DVB (4341): VIDIOCSMICROCODE were missing on compat_ioctl32
V4L/DVB (4322): Fix dvb-pll autoprobing
V4L/DVB (4311): Fix possible dvb-pll oops
V4L/DVB (4337): Refine dead code elimination in pvrusb2
V4L/DVB (4323): [budget/budget-av/budget-ci/budget-patch drivers] fixed DMA start/stop code
V4L/DVB (4316): Check __must_check warnings
V4L/DVB (4314): Set the Auxiliary Byte when tuning LG H06xF in analog mode
V4L/DVB (4313): Bugfix for keycode calculation on NPG remotes
V4L/DVB (4310): Saa7134: rename dmasound_{init, exit}
V4L/DVB (4306): Support non interlaced capture by default for saa713x
V4L/DVB (4298): Check all __must_check warnings in bttv.
...
When we introduced -rR then aic7xxx no loger could pick up definition
of YACC&LEX from make - so do it explicit now.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Adds a __find_governor() helper function to look up a governor by
name. Also restructures some error handling to conform to the
"single-exit" model which is generally preferred for kernel code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Dave Jones <davej@redhat.com>
I just stumbled on this bug/feature, this is how to reproduce it:
# echo 450000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
# echo 450000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
# echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
# cpufreq-info -p
450000 450000 powersave
# echo 1800000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq ; echo $?
0
# cpufreq-info -p
450000 450000 powersave
Here it is. The kernel refuses to set a min_freq higher than the
max_freq but it allows a max_freq lower than min_freq (lowering min_freq
also).
This behaviour is pretty straightforward (but undocumented) and it
doesn't return an error altough failing to accomplish the requested
action (set min_freq).
The problem (IMO) is basically that userspace is not allowed to set a
full policy atomically while the kernel always does that thus it must
enforce an ordering on operations.
The attached patch returns -EINVAL if trying to increase frequencies
starting from scaling_min_freq and documents the correct ordering of writes.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Dominik Brodowski <linux at dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
--
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Minor comment fix for misc_64.S
[POWERPC] Use H_CEDE on non-SMT
[POWERPC] force 64bit mode in fwnmi handlers to workaround firmware bugs
[POWERPC] PMAC_APM_EMU should depend on ADB_PMU
[POWERPC] Fix new interrupt code (MPIC detection)
[POWERPC] Fix new interrupt code (MPIC endianness)
[POWERPC] Add cpufreq support for Xserve G5
[POWERPC] Xserve G5 thermal control fixes
[POWERPC] Fix mem= handling when the memory limit is > RMO size
[POWERPC] More offb/bootx fixes
[POWERPC] Fix legacy_serial.c error handling on 32 bits
[POWERPC] Fix default clock for udbg_16550
[POWERPC] Fix non-MPIC CHRPs with CONFIG_SMP set
[POWERPC] Fix 32 bits warning in prom_init.c
[POWERPC] Workaround Pegasos incorrect ISA "ranges"
[POWERPC] fix up front-LED Kconfig
Since we now use the generic backlight infrastructure, I think we need to
call rivafb_bl_init before calling register_framebuffer since otherwise
rivafb_bl_init might race with the framebuffer layer already opening the
device and setting up the video mode. In this case we might end up with a
not yet fully intialized backlight (info->bl_dev still NULL) when calling
riva_bl_set_power via rivafb_set_par/rivafb_load_video_mode and the kernel
dies without any further notice during boot.
This fixes booting current git on a PB 6,1. In this case radeonfb/atyfb
would be affected too - I can fix that too but don't have any hardware to
test this on.
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_FB_NVIDIA already depends on CONFIG_PCI in drivers/video/Kconfig.
Driver does an extra ``sanity check'' which is then redundant.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Cc: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes several problems:
- The legacy backlight value might be set at interrupt time. Introduced
a worker to prevent it from directly calling the backlight code.
- via-pmu allows the backlight to be grabbed, in which case we need to
prevent other kernel code from changing the brightness.
- Don't send PMU requests in via-pmu-backlight when the machine is about
to sleep or waking up.
- More Kconfig fixes.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many IBM Thinkpad T4* models and some R* and X* with radeon video cards draw
too much power when suspended to RAM, reducing drastically the battery
lifetime. The solution is to enable suspend-to-D2 on these machines. They
are whitelisted through their subsystem vendor/device ID. This fixes
http://bugzilla.kernel.org/show_bug.cgi?id=3022
The patch introduces a framework to alter the pm_mode and reinit_func fields
of the radeonfb_info structure based on a whitelist. This should facilitate
future hardware-dependent workarounds. The workaround for the Samsung P35
that is already in the radeonfb code has been rewritten using this framework.
The behavior can be overridden with module options:
i) video=radeonfb:force_sleep=1
enable suspend-to-D2 also on non-whitelisted machines (useful for
testing new notebook models),
ii) video=radeonfb:ignore_devlist=1
Disable checking the whitelist and do not apply any workarounds.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The backlight and lcd subsystems can be notified by the framebuffer layer
of blanking events. However, these subsystems, as a whole, can function
independently from the framebuffer layer. But in order to enable to the
lcd and backlight subsystems, the framebuffer has to be compiled also,
effectively sucking in a huge amount of unneeded code.
To prevent dependency problems, separate out the framebuffer notification
mechanism from the framebuffer layer and permanently link it to the kernel.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The geode hwrng leaks an iomapped resource, if hwrng_register() fails.
This fixes it.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The intel hwrng leaks an iomapped resource, if hwrng_register() failes.
This fixes it.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
swsusp is unable to suspend my machine (DTK FortisPro TOP-5A notebook) with
kernel 2.6.17.5 because it's unable to suspend PNP device 00:16 (mouse).
The problem is in PNP BIOS. pnp_bus_suspend() calls pnp_stop_dev() for the
device if the device can be disabled according to pnp_can_disable(). The
problem is that pnpbios_disable_resources() returns -EPERM if the device is
not dynamic (!pnpbios_is_dynamic()) but insert_device() happily sets
PNP_DISABLE capability/flag even if the device is not dynamic. So we try
to disable non-dynamic devices which will fail. This patch prevents
insert_device() from setting PNP_DISABLE if the device is not dynamic and
fixes suspend on my system.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hide the video drivers for onboard graphics found in early PCI PowerMacs in
Apple G5 config files.
drivers/built-in.o: In function `.platinumfb_probe':
platinumfb.c:(.text+0x377a0): undefined reference to `.nvram_read_byte'
platinumfb.c:(.text+0x37830): undefined reference to `.nvram_read_byte'
drivers/built-in.o: In function `.control_init':
controlfb.c:(.init.text+0x1938): undefined reference to `.nvram_read_byte'
controlfb.c:(.init.text+0x1968): undefined reference to `.nvram_read_byte'
drivers/built-in.o: In function `.valkyriefb_init':
(.init.text+0x2300): undefined reference to `.nvram_read_byte'
drivers/built-in.o:(.init.text+0x239c): more undefined references to `.nvram_read_byte' follow
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Values displayed when by cardctl config are horribly wrong for 16bit cards.
this fixes it up by not using memcpy() since source and target struct are
very different.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
the p_dev == NULL checks are wrong. the called functions handle a NULL
p_dev on their own. w/o this patch output of cardcctl status and cardctl
config is broken for cardbus cards or when the slot is empty.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
WARNING: drivers/video/console/mdacon.o - Section mismatch: reference to .init.text: from .text between 'mdacon_startup' (at offset 0x123) and 'mdacon_init'
WARNING: drivers/video/console/mdacon.o - Section mismatch: reference to .init.text: from .text between 'mdacon_startup' (at offset 0x18b) and 'mdacon_init'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SGI IOC4 IDE device always shares an interrupt with other devices which
are part of IOC4. As such, IDEPCI_SHARE_IRQ should always be enabled when
BLK_DEV_SGIIOC4 is enabled.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up kernel-doc comments in drivers/pci/search.c (line sizes and typos).
Enable that source file in DocBook/kernel-api.tmpl.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use hotplug version of register_cpu_notifier in late init functions.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When reading from nbd device, we need to receive all the data after
receiving reply packet from the server - otherwise such request will never
be ended.
If socket is closed right after accepting reply control packet and in the
middle of waiting for read data, nbd_read_stat() returns NULL and
nbd_end_request() is not called.
This patch fixes it.
Signed-off-by: Michal Feix <michal@feix.cz>
Acked-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should check magic sequence in reply packet before trying to find
request with it's request handle. This also solves the problem with
"Unexpected reply" message beeing logged, when packet with invalid magic is
received.
Signed-off-by: Michal Feix <michal@feix.cz>
Acked-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pkt_*_dev functions operate on not-this-blockdevice, and that is
sufficiently checked at setup time. As a result there is a natural
hierarchy, which needs nesting annotations
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When resuming from suspend-to-RAM, the NMI watchdog detects a lockup in
ide_wait_not_busy. Here's a screenshot of the trace taken by a digital
camera: http://www.uamt.feec.vutbr.cz/rizeni/pom/DSC03510-2.JPG
Let's touch the NMI watchdog in ide_wait_not_busy. The system then resumes
correctly from STR.
[akpm@osdl.org: modular build fix]
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A static struct mustn't be exported.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Events sent by Process Events Connector from a 64-bit kernel are not binary
compatible with a 32-bit userspace program because the "timestamp" field
(struct timespec) is not arch independent. This affects the fields that
follow "timestamp" as they will be be off by 8 bytes.
This is a problem for 32-bit userspace programs running with 64-bit kernels
on ppc64, s390, x86-64.. any "biarch" system.
Matt had submitted a different solution to lkml as an RFC earlier. We have
since switched to a solution recommended by Evgeniy Polyakov.
This patch fixes the problem by changing the timestamp to be a __u64, which
stores the number of nanoseconds.
Tested on a x86_64 system with both 32 bit application and 64 bit
application and on a i386 system.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Guillaume Thouvenin <guillaume.thouvenin@bull.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A previous patch changed VBI_OFFSET to match what the datasheets say it
should be. However, the bt8x8 datasheets are wrong. The old value of
244 is closer to what is actually observed. The real value appears to
not be constant and is different for different chip revisions.
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Take note of which sysfs files / groups that the pvrusb2 successfully
creates and only delete those specific items when tearing things
down. (Previously we just blindly tore everything down every time.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Revert bttv-driver.c from video_device_create_file() to use
class_device_create_file() again. video_device_create_file() is only
available when V4L1 is on.
Proper error checking is added for failure of class_device_create_file().
Will print error message and unroll partially created sysfs entries.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add proper error checking and roll-back for failure of
class_device_create_file() in videodev.c. Print error messages and
unroll partially created sysfs entries.
Also, failure of class_device_register() in video_register_device() is
handled correctly. It was failing to de-allocate the minor number. This
must be done in video_register_device(), since the caller has no way of
knowing if failure occurred before or after the class device was
registered.
Also added an error message if video_register_device() is called with
an unknown type, which should never happen.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A patch from Aug, 17 activated by mistake OVERLAY flag on cx88-video,
together with several cx88-blackbird cleanups. This makes the cx88 driver
to report:
/dev/video0 [v4l2]: ioctl VIDIOC_G_FBUF: Invalid argument
instead of:
/dev/video0 [v4l2]: no overlay support
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed usage of HAVE_V4L1
Including videodev.h will just include videodev2.h if V4L1 is not supported
V4L1 code at core drivers will honor CONFIG_V4L1_COMPAT stuff
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
video_code size is 24 on i386 and 32 on x86_64, so a proper handling is needed
on compat_ioctl32 to fix it.
This code should be tested, since just *a few* boards use this ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trent Piepho pointed out that the pll test i2c transmission is slightly
wrong; it was transmitting a zero length message, and then reading from the
PLL. This was wrong; it should only be transmitting a single read i2c message.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Supplying a NULL i2c adapter to dvb_pll_attach is allowed, for example with
mt352 demods. However, the pll i2c probe will segfault because it does not
check for this.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix bug reported by Andrew de Quincey:
After cold boot the saa7146 DMA did not start if the demuxer was opened
before the frontend has locked to the signal.
DMA transfers will be started now if (and only if)
the frontend is locked and data should be sent to the demuxer.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Check __must_check warnings for class_device_register and class_device_create_file
video_device_create_file was declared as a void, but instead should
return the int value of class_device_create_file.
Move the check from bttv-driver.c into v4l2-dev.h, because all other
callers of video_device_create_file must also be checked.
Replace the call to class_device_create_file in videodev.c with
video_device_create_file, as defined in v4l2-dev.h, so that the
return value of class_device_create_file will be checked.
Check the return value of class_device_register in videodev.c and
pvrusb2-sysfs.c
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the LG H06xF tuners, an auxiliary byte must be sent after the
standard four-byte i2c sequence. The code that does this is currently in
the wrong place, causing random bytes to be written to the tuner over
i2c in the set_type function.
This patch moves this code from set_type to default_set_tv_freq.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix keycode calculations (all codes for this remote were wrong due to a
lost + sign)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Two different exports with the same name are not a good idea:
$ grep -r EXPORT_SYMBOL\(dmasound_init\) *
drivers/media/video/saa7134/saa7134-core.c:EXPORT_SYMBOL(dmasound_init);
sound/oss/dmasound/dmasound_core.c:EXPORT_SYMBOL(dmasound_init);
$
This patch renames the saa7134 dmasound_{init,exit} to
saa7134_dmasound_{init,exit}.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch just sets the option noninterlaced to 1 by default since
it has no known disadvantages. It is still possibe to get the old
behaviour by setting noninterlaced=0.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To prevent autoloading of the driver, as it then conflicts with every other
saa7146 device in existence.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix typo in comment for TDA9819
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It was pointed out on the mailing list that this PLL definition is broken. I
went back to the original dibusb driver and confirmed it used to use these
settings, as well as consulting the datasheet.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the stv0299 native DISEQC implementation instead of the bitbanging one
as required by the ves1893. This was originally found by Oliver Endriss.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The changes to add frontend reinitialisation moved the position where the
init() op is called into the frontend thread. Unfortunately, since DISEQC
operations do not use the frontend thread, this meant that DISEQC could be
called against an uninitalised frontend, leading to all sorts of trouble.
Patch fixes this by reinstating the original fronted intialisation call.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some cards have multiple possible addresses for their PLLs, with no other
way to tell if a PLL is present or not apart from probing to see if an i2c
device is present. This adds a quick check to see if an i2c device is
present at the given i2c address.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Okay, Fix both typo's in one patch .The impact is that the incorrect value
was being computed for blinking LED and interrupt moderation values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Always do a dummy RDMA after loading the firmware to work around
buggy PCIe chipsets which do not implement resending properly.
This is so cheap as to be almost free, and should never have been
conditional on the tx boundary != 4096.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There was an issue in the data structure defined by megaraid driver
casuing "kernel unaligned access.." messages to be displayed during
IOCTL on IA64 platform.
The issue has been reported/fixed by Sakurai Hiroomi
[sakurai_hiro@soft.fujitsu.com].
Signed-Off By: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With this patch, driver will protect data corruption created by
INQUIRY with EVPD request to megaraid controllers. As specified in
the changelog, megaraid F/W already has fixed the issue and being
under process of release. Meanwhile, driver will protect the system
with this patch.
Signed-Off By: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains
- a fix for 64-bit DMA capability check in megaraid_{mm,mbox} driver.
- includes changes (going back to 32-bit DMA mask if 64-bit DMA mask
failes) suggested by James with previous patch.
- addition of SATA 150-4/6 as commented by Vasily Averin.
With patch, the driver access PCIconfiguration space with dedicated
offset to read a signature. If the signature read, it means that the
controller has capability to handle 64-bit DMA.
Without this patch, the driver used to blindly claim 64-bit DMA
capability.
The issue has been reported by Vasily Averin [vvs@sw.ru].
Thank you Vasily for the reporting.
Signed-Off By: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The version info is useful for iscsi tcp, iser and qla4xxx so move to
transport class.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We were leaking some strings. This patch just frees them.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Must pass ISCSI_ERR values from the recv path and propogate them
upwards.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We currently try to allocate a max_recv_data_segment_length
which can be very large (default is 64K), and common uses
are up to 1MB. It is very very difficult to allocte this
much contiguous memory and it turns out we never even use it.
We really only need a couple of pages, so this patch has us
allocates just what we know what we need today.
Later if vendors start adding vendor specific data and
we need to handle large buffers we can do this, but for
the last 4 years we have not seen anyone do this or request
it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iscsi_tcp can send error events from soft irq context so we
cannot use GFP_KERNEL.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We are touching the cls_session after we have freed
it. This causes a oops.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When we enter recovery and flush the running commands
we cannot freee the connection before flushing the commands.
Some commands may have a reference to the connection
that needs to be released before. iscsi_stop was forcing
the term and suspend too early and was causing a oops
in iser, so this patch removes those callbacks all together
and allows the LLD to handle that detail.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Abort handler fixes.
If a connection is dropped and reconnected while an abort is
running then we should assume the recovery code will clean up
the abort. Not doing so causes a oops.
And if a command completes then we get the status for the abort, we do not
need to call into the LLD to cleanup the resources. Doing this causes
and oops in iser because it ends up freeing some resources twice.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
if iscsi_data_rsp fails we must bail out. Since the pdu values like
data length are invalid we cannot continue to process the data since
it could over run buffers.
This fixes a bug with cisco 5428s where that target is sending
too much data.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The iscsi tcp code can pluck multiple rt2s from the tasks's r2tqueue
in the xmit code. This can result in the task being queued on the xmit queue
but gettting completed at the same time.
This patch fixes the above bug by making the fifo a list so
we always remove the entry on the list del.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In the xmit patch we are sending a -EXXX value to iscsi_conn_failure
which is causing userspace to get confused.
We should be sending a ISCSI_ERR_* value that userspace understands.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
IOP reset message should be posted to inbound message register
instead of outbound message register.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The follow patch fixes a problem for Matt Taggart.
The Compaq system he had (dl380?) has a SmartArray device that exposes
the 53c1510 device in both RAID and "normal" modes. The difference
is in RAID mode, the smart array driver (IIRC) should claim the
device instead of sym2 driver. Patch below prevents sym2 from
claiming the device when the RAID "daughter board" is attached.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
HAL and friends have a tendency to trigger this one all the time.
It's not really interesting, so kill it. The vendor kernels all do
anyways.
Signed-off-by: Jens Axboe <axboe@suse.de>
Some drives claim they support cache flushing, but get seriously
confused if you try. Add this option to be able to boot with
barriers enabled by default.
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch fixes undefined refereneces to pmu_ symbols on 2.6.17.
Signed-Off-By: Danny van Dyk <kugelfang@gentoo.org>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The thermal control for the Xserve G5s had a few issues. For one, the
way to program the RPM fans speeds into the FCU is different between it
and the desktop models, which I didn't figure out until recently, and it
was missing a control loop for the slots fan, running it too fast. Both
of those problems were causing the machine to be much more noisy than
necessary. This patch also changes the fixed value of the slots fan for
desktop G5s to 40% instead of 50%. It seems to still have a pretty good
airflow that way and is much less noisy.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When determining whether there's a key to set or not, orinoco should be
looking at the key length, not the key data. Otherwise confusion reigns
when trying to set TX key only, passing in zero-length key, but non-NULL
pointer. Key length takes precedence over non-NULL key data.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johann Uhrmann reported a bcm43xx crash and Michael Buesch tracked
it down to a problem with the new shared key auth code (recursive
calls into the driver)
This patch (effectively Michael's patch with a couple of small
modifications) solves the problem by sending the authentication
challenge response frame from a workqueue entry.
I also removed a lone \n from the bcm43xx messages relating to
authentication mode - this small change was previously discussed but
not patched in.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver airo (for Cisco Wlan-Cards) complains about "failed to load
transform for AES", when it is loaded and CRYPTO_AES is not selected
in Kconfig.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1201 has nasty tendency to emit magicall anti-wifi cloud when it is
inserted into slot, but not used.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fail to create a ccwgroup device if a ccw device is passed in twice.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In special conditions where a subchannel rejects the HALT I/O-
instruction with a busy indication (cc 2), I/O may stall.
I/O request termination logic retries HALT I/O indefinitely
because it expects HALT I/O to alter the subchannel status which
is not true when cc 2 is returned.
In case of a busy indication, try CLEAR I/O instruction immediately.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This fixes three drivers to compile again after my patch that removes
the data_cmnd member from struct scsi_cmnd.
The fas216 change is trivial, it should have been using ->cmnd all the
time.
NCR53C9 (which seem to be mostly duplicate driver with esp.c!) is doing
something odd, it should only have looked at ->cmnd before not the saved
copy that is kept for the error handlers sake. Note that it really
should deal with the sync setting themselves but use the generic domain
validation code that get this right - but that's for later let's push
this simple compile fix for now.
And sorry for the late fix for this, I have been busy with OLS and
associated activities last week.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SCSI] esp: Fix build.
[SPARC]: Fix SA_STATIC_ALLOC value.
[SPARC64]: Explicitly print return PC when the kernel fault PC is bogus.
The patch below moves the cpu hotplugging higher up in the cpufreq
layering; this is needed to avoid recursive taking of the cpu hotplug
lock and to otherwise detangle the mess.
The new rules are:
1. you must do lock_cpu_hotplug() around the following functions:
__cpufreq_driver_target
__cpufreq_governor (for CPUFREQ_GOV_LIMITS operation only)
__cpufreq_set_policy
2. governer methods (.governer) must NOT take the lock_cpu_hotplug()
lock in any way; they are called with the lock taken already
3. if your governer spawns a thread that does things, like calling
__cpufreq_driver_target, your thread must honor rule #1.
4. the policy lock and other cpufreq internal locks nest within
the lock_cpu_hotplug() lock.
I'm not entirely happy about how the __cpufreq_governor rule ended up
(conditional locking rule depending on the argument) but basically all
callers pass this as a constant so it's not too horrible.
The patch also removes the cpufreq_governor() function since during the
locking audit it turned out to be entirely unused (so no need to fix it)
The patch works on my testbox, but it could use more testing
(otoh... it can't be much worse than the current code)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without this quirk, e100 can be pulling on a shared
interrupt line when another device (eg. USB) loads,
causing the interrupt to scream and get disabled.
http://bugzilla.kernel.org/show_bug.cgi?id=5918
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Handle dev_alloc_skb() failures when initializing the RX rings.
Without proper handling, the driver will crash when using a partial
ring.
Thanks to Stephane Doyon <sdoyon@max-t.com> for reporting the bug and
providing the initial patch.
Howie Xu <howie@vmware.com> also reported the same issue.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tg3_restart_hw() to handle failures when re-initializing the
device.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ACPI_EXCEPTION() patch enabled a bunch of messages to print
even in the non-DEBUG kernel. Need to change a couple back,
and note that ACPI_EXCEPTION takes no \n, but ACPI_DEBUG_PRINT does.
No context for object [%p]\n
Device `[%s]' is not power manageable\n
Signed-off-by: Len Brown <len.brown@intel.com>
There were still some issues with offb when BootX doesn't provide a
proper display node, this fixes them. This also re-instates the
palette hacks that were disabled a couple of kernel versions ago when
I converted to the new OF parsing, and shuffles some functions around
to avoid prototypes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes the front-LED Kconfig issues I introduced while
creating it. Apparently having a dependency isn't enough to have the
select not evaluated or something like that.
The patch also changes the default configuration for pmac32 select the
default for the LED to be the IDE trigger. While I was at it, I
completely updated the defconfig and also added snd-aoa to it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to postpone the queue startup until after the softirq
handler has actually finished some requests, otherwise we could
be racing with cciss_softirq_done() and not actually restart
the queue handling.
Signed-off-by: Jens Axboe <axboe@suse.de>
The data_cmd[] member got deleted, so do not use it any more. Scsi
commands do not have their ->cmd[] overwritten temporary to probe for
status after an error before retrying.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom dongles with HID proxy support actually support SCO over
HCI if the SCO buffer size values are corrected. So instead of disabling
the SCO support, mark this dongle with the quirk for the Bluetooth core
to correct the wrong buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch disables the ISOC transfers for another broken RTX Telecom
based USB dongle. Starting the USB ISOC transfers only ends in a burst
of error messages for invalid SCO packets on connection handle 0.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Belkin F8T012 and F8T013 devices are both based on a Bluetooth chip
from Broadcom and their SCO buffer size values are wrong. The Bluetooth
core should correct these values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SCO buffer size values on IBM/Lenovo ThinkPad laptops with a
Bluetooth chip from Broadcom are wrong. The USB Bluetooth driver
has to set a quirk to correct the SCO buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Read the max_cmds value from the response to the QUERY_FW command
before printing out the value, so that the real value goes into the
debug output.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The neighbour ha field may get updated without destroying the
neighbour. In this case, the ha field gets out of sync with the
address handle stored in ipoib_neigh->ah, with the result that
the ah field would point to an incorrect path, resulting in all
packets being lost.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Need to set mcast->ah before debug code dereferences it.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Validate MADs sent by userspace clients for spec compliance with
C13-18.1.1 (prevent duplicate requests and responses sent on the
same port). Without this, RMPP transactions get aborted because
of duplicate packets.
This patch is similar to that provided by Jack Morgenstein.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_skip_sge() doesn't exactly duplicate the side effects of
ipath_copy_sge() if num_sge > 1 since it doesn't decrement ss->num_sge.
This could result in the sg_list being accessed out of bounds.
Since ipath_skip_sge() is almost always called with num_sge == 1,
the original "optimization" is almost never used.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I am still working on a proposal to remove the phys_to_virt() calls
in the ib_ipath driver. In the mean time, this patch allows SRP
to work by fixing the R_Key check and conversion from IB address
to kernel virtual address. It also returns the correct page size
for FMRs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a problem where certain error packets are passed
to the InfiniBand layer for processing even though the packet
actually was received with an error.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Mem-free HCAs always keep one spare SRQ WQE, so the SRQ limit cannot
be set beyond srq->max - 1.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Lockdep warns because uverbs is trying to take uobj->mutex when it
already holds that lock. This is because there are really multiple
types of uobjs even though all of their locks are initialized in
common code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_uverbs_create_ah() and ib_uverbs_create_srq() did not release the
PD's read lock in their error paths, which lead to deadlock when
destroying the PD.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Shutting down the ondemand policy was fraught with potential
problems, causing issues for SMP suspend (which wants to hot-
unplug) all but the last CPU.
This should fix at least the worst problems (divide-by-zero
and infinite wait for the workqueue to shut down).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[TIPC]: Removing useless casts
[IPV4]: Fix nexthop realm dumping for multipath routes
[DUMMY]: Avoid an oops when dummy_init_one() failed
[IFB] After ifb_init_one() failed, i is increased. Decrease
[NET]: Fix reversed error test in netif_tx_trylock
[MAINTAINERS]: Mark LAPB as Oprhan.
[NET]: Conversions from kmalloc+memset to k(z|c)alloc.
[NET]: sun happymeal, little pci cleanup
[IrDA]: Use alloc_skb() in IrDA TX path
[I/OAT]: Remove pci_module_init() from Intel I/OAT DMA engine
[I/OAT]: net/core/user_dma.c should #include <net/netdma.h>
[SCTP]: ADDIP: Don't use an address as source until it is ASCONF-ACKed
[SCTP]: Set chunk->data_accepted only if we are going to accept it.
[SCTP]: Verify all the paths to a peer via heartbeat before using them.
[SCTP]: Unhash the endpoint in sctp_endpoint_free().
[SCTP]: Check for NULL arg to sctp_bucket_destroy().
[PKT_SCHED] netem: Fix slab corruption with netem (2nd try)
[WAN]: Converted synclink drivers to use netif_carrier_*()
[WAN]: Cosmetic changes to N2 and C101 drivers
[WAN]: Added missing netif_dormant_off() to generic HDLC
...
It before entering in the loop for freeing the other ifb devices.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_register_driver instead of pci_module_init. Use PCI_DEVICE macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes pci_module_init() to pci_register_driver().
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
WAN: Converted synclink drivers to use netif_carrier_*() instead
of hdlc_set_carrier().
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
WAN: Fixed a problem with PPP/raw HDLC/X.25 protocols not doing
netif_dormant_off() at startup.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just do a linear enumeration so that we handle sun4d systems
correctly. As a consequence, eliminate the hard coded keyboard and
mouse channel line values, use the CONS_{KEYB,MS} flags instead.
Also, report the keyboard/mouse Zilog channels just like the uart ones
do.
Signed-off-by: David S. Miller <davem@davemloft.net>
