Pull networking fixes from David Miller:
1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
from Steffen Klassert.
2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
Alexei Starovoitov.
3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
Michal Schmidt.
4) We can get a divide by zero when TCP socket are morphed into
listening state, fix from Eric Dumazet.
5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
skb_complete_tx_timestamp(). From Eric Dumazet.
6) Use after free in dccp_feat_activate_values(), also from Eric
Dumazet.
7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
Jarod Wilson.
8) Fix use after free in vrf_xmit(), from David Ahern.
9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
Alexey Kodanev.
10) Properly check napi_complete_done() return value in order to decide
whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
Lendacky.
11) Fix double free of hwmon device in marvell phy driver, from Andrew
Lunn.
12) Don't crash on malformed netlink attributes in act_connmark, from
Etienne Noss.
13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
from Sabrina Dubroca.
14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
Florian Westphal.
15) Fix routing redirect races in dccp and tcp, basically the ICMP
handler can't modify the socket's cached route in it's locked by the
user at this moment. From Jon Maxwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
qed: Enable iSCSI Out-of-Order
qed: Correct out-of-bound access in OOO history
qed: Fix interrupt flags on Rx LL2
qed: Free previous connections when releasing iSCSI
qed: Fix mapping leak on LL2 rx flow
qed: Prevent creation of too-big u32-chains
qed: Align CIDs according to DORQ requirement
mlxsw: reg: Fix SPVMLR max record count
mlxsw: reg: Fix SPVM max record count
net: Resend IGMP memberships upon peer notification.
dccp: fix memory leak during tear-down of unsuccessful connection request
tun: fix premature POLLOUT notification on tun devices
dccp/tcp: fix routing redirect race
ucc/hdlc: fix two little issue
vxlan: fix ovs support
net: use net->count to check whether a netns is alive or not
bridge: drop netfilter fake rtable unconditionally
ipv6: avoid write to a possibly cloned skb
net: wimax/i2400m: fix NULL-deref at probe
isdn/gigaset: fix NULL-deref at probe
...
Missing in the initial submission, qed fails to propagate qedi's
request to enable OOO to firmware.
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to set the number of entries in database, otherwise the logic
would quickly surpass the array.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before iterating over the the LL2 Rx ring, the ring's
spinlock is taken via spin_lock_irqsave().
The actual processing of the packet [including handling
by the protocol driver] is done without said lock,
so qed releases the spinlock and re-claims it afterwards.
Problem is that the final spin_lock_irqrestore() at the end
of the iteration uses the original flags saved from the
initial irqsave() instead of the flags from the most recent
irqsave(). So it's possible that the interrupt status would
be incorrect at the end of the processing.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
CC: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current Logic would allow the creation of a chain with U32_MAX + 1
elements, when the actual maximum supported by the driver infrastructure
is U32_MAX.
Fixes: a91eb52abb ("qed: Revisit chain implementation")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.
Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.
Fixes: dbb799c397 ("qed: Initialize hardware for new protocols")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.
Fixes: a4feea74cd ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.
Fixes: b2e345f9a4 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aszlig observed failing ssh tunnels (-w) during initialization since
commit cc9da6cc4f ("ipv6: addrconf: use stable address generator for
ARPHRD_NONE"). We already had reports that the mentioned commit breaks
Juniper VPN connections. I can't clearly say that the Juniper VPN client
has the same problem, but it is worth a try to hint to this patch.
Because of the early generation of link local addresses, the kernel now
can start asking for routers on the local subnet much earlier than usual.
Those router solicitation packets arrive inside the ssh channels and
should be transmitted to the tun fd before the configuration scripts
might have upped the interface and made it ready for transmission.
ssh polls on the interface and receives back a POLL_OUT. It tries to send
the earily router solicitation packet to the tun interface. Unfortunately
it hasn't been up'ed yet by config scripts, thus failing with -EIO. ssh
doesn't retry again and considers the tun interface broken forever.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=121131
Fixes: cc9da6cc4f ("ipv6: addrconf: use stable address generator for ARPHRD_NONE")
Cc: Bjørn Mork <bjorn@mork.no>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reported-by: Jonas Lippuner <jonas@lippuner.ca>
Cc: Jonas Lippuner <jonas@lippuner.ca>
Reported-by: aszlig <aszlig@redmoonstudios.org>
Cc: aszlig <aszlig@redmoonstudios.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. modify bd_status from u32 to u16 in function hdlc_rx_done,
because bd_status register is 16bits
2. write bd_length register before writing bd_status register
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The required changes in the function vxlan_dev_create() were missing
in commit 8bcdc4f3a2.
The vxlan device is not registered anymore after this patch and the error
path causes an stack dump:
WARNING: CPU: 3 PID: 1498 at net/core/dev.c:6713 rollback_registered_many+0x9d/0x3f0
Fixes: 8bcdc4f3a2 ("vxlan: add changelink support")
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
The endpoints are specifically dereferenced in the i2400m_bootrom_init
path during probe (e.g. in i2400mu_tx_bulk_out).
Fixes: f398e4240f ("i2400m/USB: probe/disconnect, dev init/shutdown
and reset backends")
Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases during XenBus disconnect event handling and subsequent
queue resource release there may be some TX handlers active on
other processors. Use RCU in order to synchronize with them.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the send indirection table from the inner device (netvsc)
to the network device context.
It is possible that netvsc_device is not present (remove in progress).
This solves potential use after free issues when packet is being
created during MTU change, shutdown, or queue count changes.
Fixes: d8e18ee0fa ("netvsc: enhance transmit select_queue")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a network interface controlled by the aquantia ethernet driver is brought
down a warning is output in dmesg (see below).
The problem is that aq_pci_func_free_irqs() is calling free_irq() before it is
calling irq_set_affinity_hint().
WARNING: CPU: 4 PID: 10068 at kernel/irq/manage.c:1503 __free_irq+0x24d/0x2b0
<snip>
Call Trace:
dump_stack+0x63/0x87
__warn+0xd1/0xf0
warn_slowpath_null+0x1d/0x20
__free_irq+0x24d/0x2b0
free_irq+0x39/0x90
aq_pci_func_free_irqs+0x52/0xa0 [atlantic]
aq_nic_stop+0xca/0xd0 [atlantic]
aq_ndev_close+0x1d/0x40 [atlantic]
__dev_close_many+0x99/0x100
__dev_close+0x67/0xb0
<snip>
Fixes: 36a4a50f40 ("net: ethernet: aquantia: switch to pci_alloc_irq_vectors")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change packet type handler to ETH_P_IP instead of ETH_P_ALL
since we are already expecting an IP packet.
Also, using ETH_P_ALL will cause the loopback test packet type handler
to be called on all outgoing packets, especially our own self loopback
test SKB, which will be validated on xmit as well, and we don't want that.
Tested with:
ethtool -t ethX
validated that the loopback test passes.
Fixes: 0952da791c ('net/mlx5e: Add support for loopback selftest')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting offloaded TC flows, we must correctly identify E-switch
rules. The current check could get us wrong w.r.t to rules set on the
PF. Since it's possible to set NIC rules on the PF, switch to SRIOV
offloads mode and then attempt to delete a NIC rule.
To solve that, we add a flags field to offloaded rules, set it on
creation time and use that over the code where currently needed.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the function setdcbx fails if the request dcbx mode
is either IEEE or CEE. We remove the IEEE/CEE mode check because
we support both IEEE and CEE interfaces.
Fixes: 3a6a931dfb ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PCI error is detected the PCI state could be corrupt, don't save
it in that flow. Save the state after initialization. After restoring the
PCI state during slot reset save it again, restoring the state destroys
the previously saved state info.
Fixes: 05ac2c0b74 ('net/mlx5: Fix race between PCI error handlers and
health work')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The autogroups list is a list of non overlapping group boundaries
sorted by their start index. If the autogroups list wasn't empty
and an empty group slot was found at the start of the list,
the new group was added to the end of the list instead of the
beginning, as the prev initializer was incorrect.
When this was repeated, it caused multiple groups to have
overlapping boundaries.
Fixed that by correctly initializing the prev pointer to the
start of the list.
Fixes: eccec8da3b ('net/mlx5: Keep autogroups list ordered')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hwmon temperature sensor devices is registered using a devm_hwmon
API call. The marvell_release() would then manually free the device,
not using a devm_hmon API, resulting in the device being removed
twice, leading to a crash in kernfs_find_ns() during the second
removal.
Remove the manual removal, which makes marvell_release() empty, so
remove it as well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 0b04680fda ("phy: marvell: Add support for temperature sensor")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcmgenet_tx_reclaim() function is used to reclaim transmit
resources in different places within the driver. Most of them
should not affect the state of the transmit flow control.
This commit relocates the logic for waking tx queues based on
freed resources to the napi polling function where it is more
appropriate.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure clock is enabled for ethtool ops.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Edwin Chan <edwin.chan@broadcom.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the internal PHY it must be powered up when the MII is probed
or the PHY will not be detected. Since the PHY is powered up at reset
this has not been a problem. However, when the kernel is restarted with
kexec the PHY will likely be powered down when the kernel starts so it
will not be detected and the Ethernet link will not be established.
This commit explicitly powers up the internal PHY when the GENET driver
is probed to correct this behavior.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a spinlock to ensure that irq0_stat is not unintentionally altered
as the result of preemption. Also removed unserviced irq0 interrupts
and removed irq1_stat since there is no bottom half service for those
interrupts.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the internal PHY is powered up during the open and resume
functions it should be powered back down if the functions fail.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reserved gphy_rev value of 0x01ff must be tested before the old
or new scheme for GPHY major versioning are tested, otherwise it will
be treated as 0xff00 according to the old scheme.
Fixes: b04a2f5b9f ("net: bcmgenet: add support for new GENET PHY revision scheme")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gap between the Tx status counters and the Rx RUNT counters is now
being added to allow correct reporting of the registers.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The location of the RBUF overflow and error counters has moved between
different version of the GENET MAC. This commit corrects the driver to
read from the correct locations depending on the version of the GENET
MAC.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the hardware, the amd-xgbe driver may use disable_irq_nosync()
and enable_irq() when an interrupt is received to process Rx packets. If
the napi_complete_done() return value isn't checked an unbalanced enable
for the IRQ could result, generating a warning stack trace.
Update the driver to only enable interrupts if napi_complete_done() returns
true.
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some situations, the firmware will return 0 for autoneg supported
speed. This may happen if the firmware detects no SFP module, for
example. The driver should ignore this so that we don't end up with
an invalid autoneg setting with nothing advertised. When SFP module
is inserted, we'll get the updated settings from firmware at that time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set DCB_CAP_DCBX_HOST capability flag only if the firmware LLDP agent
is not running.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we call bnxt_reset_task() due to tx timeout, we should call
bnxt_ulp_stop() to inform the RDMA driver about the error and the
impending reset.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware call to do function reset is done too late. It is causing
the rings that have been reserved to be freed. In NPAR mode, this bug
is causing us to run out of rings.
Fixes: 391be5c273 ("bnxt_en: Implement new scheme to reserve tx rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing copyright does not give any useful information on the boot
process.
Furthermore, the email address printed is obsolete since
commit ba57b6f204 ("MAINTAINERS: fix bouncing tun/tap entries")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typos and add the following to the scripts/spelling.txt:
overide||override
While we are here, fix the doubled "address" in the touched line
Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt.
Also, fix the comment block style in the touched hunks in
drivers/media/dvb-frontends/drx39xyj/drx_driver.h.
Link: http://lkml.kernel.org/r/1481573103-11329-21-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In qed_ll2_start_ooo() the ll2_info variable is uninitialized and then
passed to qed_ll2_acquire_connection() where it is copied into a new
memory space.
This shouldn't cause any issue as long as non of the copied memory is
every read.
But the potential for a bug being introduced by reading this memory
is real.
Detected by CoverityScan, CID#1399632 ("Uninitialized scalar variable")
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not consider IPv6 frames with zero UDP checksum as frames
with bad checksum and drop them.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When booted with ACPI, random mac addresses are being
assigned to node1 interfaces due to mismatch of bgx_id
in BGX driver and ACPI tables.
This patch fixes this issue by setting maximum BGX devices
per node based on platform/soc instead of a macro. This
change will set the bgx_id appropriately.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When BGX/LMACs are in QSGMII mode, for some LMACs, mode info is
not being printed. This patch will fix that. With changes already
done to not do any sort of serdes 2 lane mapping config calculation
in kernel driver, we can get rid of this logic.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ACPI support has been added to ARM IOMMU driver in 4.10 kernel
and that has resulted in VNIC interfaces throwing translation
faults when kernel is booted with ACPI as driver was not using
DMA API. This patch fixes the issue by using DMA API which inturn
will create translation tables when IOMMU is enabled.
Also VNIC doesn't have a seperate receive buffer ring per receive
queue, so there is no 1:1 descriptor index matching between CQE_RX
and the index in buffer ring from where a buffer has been used for
DMA'ing. Unlike other NICs, here it's not possible to maintain dma
address to virt address mappings within the driver. This leaves us
no other choice but to use IOMMU's IOVA address conversion API to
get buffer's virtual address which can be given to network stack
for processing.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This warnings may be hit even in case they should not - in case user
puts a TC-flower rule which failed to be offloaded. So just remove them.
Reported-by: Petr Machata <petrm@mellanox.com>
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: commit 7aa0f5aa90 ("mlxsw: spectrum: Implement TC flower offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This restores the ability to set a team device's mtu to anything higher
than 1500. Similar to the reported issue with bonding, the team driver
calls ether_setup(), which sets an initial max_mtu of 1500, while the
underlying hardware can handle something much larger. Just set it to
ETH_MAX_MTU to support all possible values, and the limitations of the
underlying devices will prevent setting anything too large.
Fixes: 91572088e3 ("net: use core MTU range checking in core net infra")
CC: Cong Wang <xiyou.wangcong@gmail.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Margetson reported a panic on his SAM460EX with Kernel 4.11-rc1:
| Unable to handle kernel paging request for data at address 0x00000014
| Oops: Kernel access of bad area, sig: 11 [#1]
| PREEMPT
| Canyonlands
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper Not tainted [...]
| task: ea838000 task.stack: ea836000
| NIP: c0599f5c LR: c0599dd8 CTR: 00000000
| REGS: ea837c80 TRAP: 0300 Not tainted [...]
| MSR: 00029000 <CE,EE,ME>
| CR: 24371242 XER: 20000000
| DEAR: 00000014 ESR: 00000000
| GPR00: c0599ce8 ea837d30 ea838000 c0e52dcc c0d56ffb [...]
| NIP [c0599f5c] emac_probe+0xfb4/0x1304
| LR [c0599dd8] emac_probe+0xe30/0x1304
| Call Trace:
| [ea837d30] [c0599ce8] emac_probe+0xd40/0x1304 (unreliable)
| [ea837d80] [c0533504] platform_drv_probe+0x48/0x90
| [ea837da0] [c0531c14] driver_probe_device+0x15c/0x2c4
| [ea837dd0] [c0531e04] __driver_attach+0x88/0xb0
| ---[ end trace ... ]---
The problem is caused by emac_dt_phy_probe() returing success (0)
for existing device-trees configurations that do not specify a
"phy-handle" property. This caused the code to skip the existing
phy probe and setup. Which led to essential phy related
data-structures being uninitialized.
This patch also removes the unused variable in emac_dt_phy_connect().
Fixes: a577ca6bad ("net: emac: add support for device-tree based PHY discovery and setup")
Reported-by: Julian Margetson <runaway@candw.ms>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
