Assume that unknown ICE1724-based cards are AC97-only that can suspend
without any additional card-specific code.
This fixes suspend on Gainward Hollywood@Home 7.1.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The rate isn't restored properly after resume since it's only set up
in hw_params, and not in prepare callback. For fixing it, put the
corresponding call to resume callback as well.
Reported-and-tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix build errors by using correct kconfig symbol name:
sound/pci/ice1712/psc724.c:417:5: error: 'struct snd_ice1712' has no member named 'pm_resume'
sound/pci/ice1712/psc724.c:418:5: error: 'struct snd_ice1712' has no member named 'pm_suspend_enabled'
[Fixed another #ifdef CONFIG_PM in the same file, too, by tiwai]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Include linux/io.h in ice1712.h since inb() and outb() are used in
inline functions there. Remove the redundant inclusion of that file
in other places at the same time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add psc724 subdriver to snd-ice1712 that provides full support for
Philips PSC724 Ultimate Edge sound cards.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Needed by Philips PSC724 subdriver. The code does not contain any
card-specific bits so other ice17xx cards using this codec could be
converted to use this generic code.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Needed by Philips PSC724 subdriver. The code does not contain any
card-specific bits so other ice17xx cards using this codec could be
converted to use this generic code.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add chip_exit callback to allow card subdrivers to do cleanup work on module
removal.
Needed by Philips PSC724 subdriver to cancel delayed work.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lots and lots of driver specific cleanups and enhancements but the only
substantial framework feature this time round is the compressed API
binding:
- Addition of ASoC bindings for the compressed API, used by the mid-x86
drivers.
- Lots of cleanups and API refreshes for CODEC drivers and DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JSSt
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.7
Lots and lots of driver specific cleanups and enhancements but the only
substantial framework feature this time round is the compressed API
binding:
- Addition of ASoC bindings for the compressed API, used by the mid-x86
drivers.
- Lots of cleanups and API refreshes for CODEC drivers and DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
The AK4396 DAC has a linear-scale attentuator, but
sound/pci/ice1712/prodigy_hifi.c used a log scale instead, which is
not quite right. This patch restores the correct scale, borrowing
from the ak4396 code in sound/pci/oxygen/oxygen.c.
Signed-off-by: Matteo Frigo <athena@fftw.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Straightforward conversion to the new pm_ops from the legacy
suspend/resume ops.
Since we change vx222, vx_core and vxpocket have to be converted,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver already defines control "Multi Track Rate Locking" which
locks the card at current rate if switched to internal clock. This patch
limits the runtime rates to this rate only, allowing proper reporting
of the card capabilities, and e.g. automatic rate conversion by the plug
plugin to the currently locked rate.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This card shares PCI ids with Chaintec AV710. Therefore, it will not be
detected automatically, it can only be activated by the module parameter
model=sq210a.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When two different cards share the same PCI vendor/subvendor
identification, allow card info based on model only.
Do not require subvendor ID.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the capture pcm only if there is at least one ADC configured in
the SYSCONF register.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Append the external clock item to the clock list only if
the SPDIF_IN capability is defined in the SPDIF register.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cards with identical PCI ids but no AC97 config in EEPROM do not have
the ac97 field initialized. We must check for this case to avoid kernel oops.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The implicit presence of module.h lured several users into
incorrectly thinking that they only needed/used modparam.h
but once we clean up the module.h presence, these will show
up as build failures, so fix 'em now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The semantics of snd_mpu401_uart_new()'s interrupt parameters are
somewhat counterintuitive: To prevent the function from allocating its
own interrupt, either the irq number must be invalid, or the irq_flags
parameter must be zero. At the same time, the irq parameter being
invalid specifies that the mpu401 code has to work without an interrupt
allocated by the caller. This implies that, if there is an interrupt
and it is allocated by the caller, the irq parameter must be set to
a valid-looking number which then isn't actually used.
With the removal of IRQF_DISABLED, zero becomes a valid irq_flags value,
which forces us to handle the parameters differently.
This patch introduces a new flag MPU401_INFO_IRQ_HOOK for when the
device interrupt is handled by the caller, and makes the allocation of
the interrupt to depend only on the irq parameter. As suggested by
Takashi, the irq_flags parameter was dropped because, when used, it had
the constant value IRQF_DISABLED.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
The name argument of request_irq() appears in /proc/interrupts, and
it's quite ugly when the name entry contains a space or special letters.
In general, it's simpler and more readable when the module name appears
there, so let's replace all entries with KBUILD_MODNAME.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The convention for pci_driver.name entry in kernel drivers seem to be
the module name or equivalent ones. But, so far, almost all PCI sound
drivers use more verbose name like "ABC Xyz (12)", and these are fairly
confusing when appearing as a file name.
This patch converts the all pci_driver.name entries in sound/pci/* to
use KBUILD_MODNAME for more unified appearance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver was using an initial value for the clock on the SPI bus
which was read from ICE1712 EEPROM,
ice->eeprom.data[ICE_EEP1_GPIO_STATE] & ICE1712_DELTA_AP_CCLK (0x02)
It appears some cards have it default high, some cards
have it default low. On my Delta 66 rev. E:
$ cat /proc/asound/M66/ice1712 | grep 'GPIO state'
GPIO state : 0x70 /* ICE1712_DELTA_AP_CCLK bit is zero */
On my Audiophile 2496:
$ cat /proc/asound/M2496/ice1712 | grep 'GPIO state'
GPIO state : 0xfe /* ICE1712_DELTA_AP_CCLK bit is one */
It must be raised before the first SPI write happens, or the write will
fail, leading to:
[ 23.248721] invalid CS8427 signature 0x0: let me try again...
I theorize that 4eb4550ab3
is no longer needed, it was a different way to workaround
the problem.
[fixed variable decleration by tiwai]
Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rev. E of the M-Audio Delta 66 is partially supported (commit
ef2cd2ccad), but the layout of the GPIO
pins was still unclear. This patch adds the GPIO definitions so that
communication to the CS8247 & 2x AK4524 works correctly.
ALSA bug#3327 has more details; users cap & jhunt report there that the
GPIO wiring is similar to the Digigram VX442 (chip select: pin 4 =
CS8427, pin 5 = AK4524 #0, pin 6 = AK4524 #1). There has been a lot of
conflicting information in the bug, but given these definitions, my
Delta 66E works; I tested analog in&out at 44.1kHz & 96kHz, analog gain
settings, S/PDIF clock sync, and S/PDIF in&out at 44.1kHz.
Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device is similar to the M-Audio Delta 1010LT in that it uses the
AK4524VF ADC/DAC, but it does not use the CS8427 for SPDIF.
The SPDIF appears to be set up correctly, but I am not able to test it
as I do not have any devices that use it.
This patch makes the ADC/DAC's and the hardware mixer visible to apps
such as alsamixer and envy24control.
Signed-off-by: Garnet MacPhee <dhubsith@comcast.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture source control of maya44 was wrongly coded with the bit
shift instead of the bit mask. Also, the slot for line-in was
wrongly assigned (slot 5 instead of 4).
Reported-by: Alex Chernyshoff <alexdsp@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Add proper suspend/resume code for Terratec Aureon cards.
Based on ice1724 suspend/resume work of Igor Chernyshev.
Fixes bug https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4944
Tested on linux-2.6.32.9
Signed-off-by: Bernhard Urban <lewurm@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use DEFINE_PCI_DEVICE_TABLE() to make PCI device ids go to
.devinit.rodata section, so they can be discarded in some cases,
and make them const.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The volume register is from 0..0x7f and 0..0x1a range is mute.
Also, fix mute combining in wm_vol_put(). The wrong behaviour was
noticed by Peter Christensen.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
I found that the sampling rate locking setting of the ice1712 sound driver
was only half-respected : when the driver was locked to, let's say, 44100Hz,
and a usermode app was requesting 48000Hz playback, the request was succesful
although the soundcard would continue to run at 44100Hz.
Here's a patch that will make those requests to fail.
Signed-off-by: Sebastien Alaiwan <sebastien.alaiwan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The volume levels in original implementation are incorrect and does
not match the dB scale. The real range is linear (in the sense of
the dB scale) from 0dB to -100dB. Remove logaritmic table and make
all volumes from range 0dB..100dB.
The tests are in RedHat's bugzilla #540817.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
