Increase mempool size from 16 to 64 entries. This increase improves
swap on dm-crypt performance.
When swapping to dm-crypt, all available memory is temporarily exhausted
and dm-crypt can only use the mempool reserve.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use local_irq_save() to disable preemption before calling
this_cpu_ptr().
Reported-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Fixes: b0b477c7e0 ("dm round robin: use percpu 'repeat_count' and 'current_path'")
Cc: stable@vger.kernel.org # 4.6+
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
After array enters in faulty state (e.g. number of failed drives
becomes more then accepted for raid5 level) it sets error flags
(one of this flags is MD_CHANGE_PENDING). For internal metadata
arrays MD_CHANGE_PENDING cleared into md_update_sb, but not for
external metadata arrays. MD_CHANGE_PENDING flag set prevents to
finish all new or non-finished IOs to array and hold them in
pending state. In some cases this can leads to deadlock situation.
For example, we have faulty array (2 of 4 drives failed) and
udev handle array state changes and blkid started (or other
userspace application that used array to read/write) but unable
to finish reads due to IO hold. At the same time we unable to get
exclusive access to array (to stop array in our case) because
another external application still use this array.
Fix makes possible to return IO with errors immediately.
So external application can finish working with array and
give exclusive access to other applications to perform
required management actions with array.
Signed-off-by: Alexey Obitotskiy <aleksey.obitotskiy@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Changing the location changes a lot of things. Holding the lock to avoid race.
This makes the .quiesce called with mddev lock hold too.
Acked-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
During a resynchronization, device status char 'a' is output on the raid
status line for every device of a RAID set. It changes from 'a' to 'A'
(unless device failure) when the resynchronization completes.
Interrupting and restarting a resynchronization, by reloading the DM
table, erroneously lead to status char 'A'.
Fix this by avoiding setting the MD_RECOVERY_REQUESTED flag in
raid_preresume().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When lvm2 userspace requests a RaidLV repair, it sets the rebuild
constructor flag on the new replacement DataLVs but does not clear the
respective MetaLVs. Hence the superblock that is loaded from such new
MetaLVs may have a non-zero incompat_features member and the constructor
will fail with false-positive on incompat_features.
Solve by initializing the incompat_features member properly.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
__CTR_FLAG_MIN_RECOVERY_RATE was used instead of __CTR_FLAG_MAX_RECOVERY_RATE
thus causing max_recovery_rate to be rejected in case min_recovery_rate
was already set.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Otherwise, there is potential for both DMF_SUSPENDED* and
DMF_NOFLUSH_SUSPENDING to not be set during dm_suspend() -- which is
definitely _not_ a valid state.
This fix, in conjuction with "dm rq: fix the starting and stopping of
blk-mq queues", addresses the potential for request-based DM multipath's
__multipath_map() to see !dm_noflush_suspending() during suspend.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Improve dm_stop_queue() to cancel any requeue_work. Also, have
dm_start_queue() and dm_stop_queue() clear/set the QUEUE_FLAG_STOPPED
for the blk-mq request_queue.
On suspend dm_stop_queue() handles stopping the blk-mq request_queue
BUT: even though the hw_queues are marked BLK_MQ_S_STOPPED at that point
there is still a race that is allowing block/blk-mq.c to call ->queue_rq
against a hctx that it really shouldn't. Add a check to
dm_mq_queue_rq() that guards against this rarity (albeit _not_
race-free).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # must patch dm.c on < 4.8 kernels
Multiple flags were being tested without locking. Protect against
non-atomic bit changes in m->flags by holding m->lock (while testing or
setting the queue_if_no_path related flags).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When the corrupt_bio_byte feature was introduced it caused READ bios to
no longer be errored with -EIO during the down_interval. This had to do
with the complexity of needing to submit READs if the corrupt_bio_byte
feature was used.
Fix it so READ bios are properly errored with -EIO; doing so early in
flakey_map() as long as there isn't a match for the corrupt_bio_byte
feature.
Fixes: a3998799fb ("dm flakey: add corrupt_bio_byte feature")
Reported-by: Akira Hayakawa <ruby.wktk@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
The counter conf->empty_inactive_list_nr is only used for determine if the
raid5 is congested which is deal with in function raid5_congested().
It was increased in get_free_stripe() when conf->inactive_list got to be
empty and decreased in release_inactive_stripe_list() when splice
temp_inactive_list to conf->inactive_list. However, this may have a
problem when raid5_get_active_stripe or stripe_add_to_batch_list was called,
because these two functions may call list_del_init(&sh->lru) to delete sh from
"conf->inactive_list + hash" which may cause "conf->inactive_list + hash" to
be empty when atomic_inc_not_zero(&sh->count) got false. So a check should be
done at these two point and increase empty_inactive_list_nr accordingly.
Otherwise the counter may get to be negative number which would influence
async readahead from VFS.
Signed-off-by: ZhengYuan Liu <liuzhengyuan@kylinos.cn>
Signed-off-by: Shaohua Li <shli@fb.com>
md pending write counter must be incremented after bio is split,
otherwise it gets decremented too many times in end bio callback and
becomes negative.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Reviewed-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull MD updates from Shaohua Li:
- A bunch of patches from Neil Brown to fix RCU usage
- Two performance improvement patches from Tomasz Majchrzak
- Alexey Obitotskiy fixes module refcount issue
- Arnd Bergmann fixes time granularity
- Cong Wang fixes a list corruption issue
- Guoqing Jiang fixes a deadlock in md-cluster
- A null pointer deference fix from me
- Song Liu fixes misuse of raid6 rmw
- Other trival/cleanup fixes from Guoqing Jiang and Xiao Ni
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md: (28 commits)
MD: fix null pointer deference
raid10: improve random reads performance
md: add missing sysfs_notify on array_state update
Fix kernel module refcount handling
md: use seconds granularity for error logging
md: reduce the number of synchronize_rcu() calls when multiple devices fail.
md: be extra careful not to take a reference to a Faulty device.
md/multipath: add rcu protection to rdev access in multipath_status.
md/raid5: add rcu protection to rdev accesses in raid5_status.
md/raid5: add rcu protection to rdev accesses in want_replace
md/raid5: add rcu protection to rdev accesses in handle_failed_sync.
md/raid1: add rcu protection to rdev in fix_read_error
md/raid1: small code cleanup in end_sync_write
md/raid1: small cleanup in raid1_end_read/write_request
md/raid10: simplify print_conf a little.
md/raid10: minor code improvement in fix_read_error()
md/raid10: add rcu protection to rdev access during reshape.
md/raid10: add rcu protection to rdev access in raid10_sync_request.
md/raid10: add rcu protection in raid10_status.
md/raid10: fix refounct imbalance when resyncing an array with a replacement device.
...
1/ Replace pcommit with ADR / directed-flushing:
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement either
ADR, or provide one or more flush addresses per nvdimm. ADR
(Asynchronous DRAM Refresh) flushes data in posted write buffers to the
memory controller on a power-fail event. Flush addresses are defined in
ACPI 6.x as an NVDIMM Firmware Interface Table (NFIT) sub-structure:
"Flush Hint Address Structure". A flush hint is an mmio address that
when written and fenced assures that all previous posted writes
targeting a given dimm have been flushed to media.
2/ On-demand ARS (address range scrub):
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the media
to refresh the bad block list, userspace can also request a re-scrub at
any time.
3/ Support for the Microsoft DSM (device specific method) command format.
4/ Support for EDK2/OVMF virtual disk device memory ranges.
5/ Various fixes and cleanups across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xCBG
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Replace pcommit with ADR / directed-flushing.
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement
either ADR, or provide one or more flush addresses per nvdimm.
ADR (Asynchronous DRAM Refresh) flushes data in posted write buffers
to the memory controller on a power-fail event.
Flush addresses are defined in ACPI 6.x as an NVDIMM Firmware
Interface Table (NFIT) sub-structure: "Flush Hint Address Structure".
A flush hint is an mmio address that when written and fenced assures
that all previous posted writes targeting a given dimm have been
flushed to media.
- On-demand ARS (address range scrub).
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the
media to refresh the bad block list, userspace can also request a
re-scrub at any time.
- Support for the Microsoft DSM (device specific method) command
format.
- Support for EDK2/OVMF virtual disk device memory ranges.
- Various fixes and cleanups across the subsystem.
* tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (41 commits)
libnvdimm-btt: Delete an unnecessary check before the function call "__nd_device_register"
nfit: do an ARS scrub on hitting a latent media error
nfit: move to nfit/ sub-directory
nfit, libnvdimm: allow an ARS scrub to be triggered on demand
libnvdimm: register nvdimm_bus devices with an nd_bus driver
pmem: clarify a debug print in pmem_clear_poison
x86/insn: remove pcommit
Revert "KVM: x86: add pcommit support"
nfit, tools/testing/nvdimm/: unify shutdown paths
libnvdimm: move ->module to struct nvdimm_bus_descriptor
nfit: cleanup acpi_nfit_init calling convention
nfit: fix _FIT evaluation memory leak + use after free
tools/testing/nvdimm: add manufacturing_{date|location} dimm properties
tools/testing/nvdimm: add virtual ramdisk range
acpi, nfit: treat virtual ramdisk SPA as pmem region
pmem: kill __pmem address space
pmem: kill wmb_pmem()
libnvdimm, pmem: use nvdimm_flush() for namespace I/O writes
fs/dax: remove wmb_pmem()
libnvdimm, pmem: flush posted-write queues on shutdown
...
The md device might not have personality (for example, ddf raid array). The
issue is introduced by 8430e7e0af9a15(md: disconnect device from personality
before trying to remove it)
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
later merged with 'for-4.8/core' to pickup the QUEUE_FLAG_DAX commits
that DM depends on to provide its DAX support
- clean up the bio-based vs request-based DM core code by moving the
request-based DM core code out to dm-rq.[hc]
- reinstate bio-based support in the DM multipath target (done with the
idea that fast storage like NVMe over Fabrics could benefit) -- while
preserving support for request_fn and blk-mq request-based DM mpath
- SCSI and DM multipath persistent reservation fixes that were
coordinated with Martin Petersen.
- the DM raid target saw the most extensive change this cycle; it now
provides reshape and takeover support (by layering ontop of the
corresponding MD capabilities)
- DAX support for DM core and the linear, stripe and error targets
- A DM thin-provisioning block discard vs allocation race fix that
addresses potential for corruption
- A stable fix for DM verity-fec's block calculation during decode
- A few cleanups and fixes to DM core and various targets
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXkRZmAAoJEMUj8QotnQNat2wH/i4LpkoGI5tI6UhyKWxRkzJp
vKaJ0zuZ2Ez73DucJujNuvaiyHq1IjHD5pfr8JQO3E8ygDkRC2KjF2O8EXp0Has6
U1uLahQej72MAs0ZJTpvfE+JiY6qyIl4K+xxuPmYm2f2S5TWTIgOetYjJQmcMlQo
Y8zFfcDYn4Dv5rMdvDT4+1ePETxq74wcBwTxyW3OAbHE1f0JjsUGdMKzXB1iTWcM
VjLjWI//ETfFdIlDO0w2Qbd90aLUjmTR2k67RGnbPj5kNUNikv/X6iiY32KERR/0
vMiiJ7JS+a44P7FJqCMoAVM/oBYFiSNpS4LYevOgHb0G0ikF8kaSeqBPC6sMYvg=
=uYt9
-----END PGP SIGNATURE-----
Merge tag 'dm-4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- initially based on Jens' 'for-4.8/core' (given all the flag churn)
and later merged with 'for-4.8/core' to pickup the QUEUE_FLAG_DAX
commits that DM depends on to provide its DAX support
- clean up the bio-based vs request-based DM core code by moving the
request-based DM core code out to dm-rq.[hc]
- reinstate bio-based support in the DM multipath target (done with the
idea that fast storage like NVMe over Fabrics could benefit) -- while
preserving support for request_fn and blk-mq request-based DM mpath
- SCSI and DM multipath persistent reservation fixes that were
coordinated with Martin Petersen.
- the DM raid target saw the most extensive change this cycle; it now
provides reshape and takeover support (by layering ontop of the
corresponding MD capabilities)
- DAX support for DM core and the linear, stripe and error targets
- a DM thin-provisioning block discard vs allocation race fix that
addresses potential for corruption
- a stable fix for DM verity-fec's block calculation during decode
- a few cleanups and fixes to DM core and various targets
* tag 'dm-4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (73 commits)
dm: allow bio-based table to be upgraded to bio-based with DAX support
dm snap: add fake origin_direct_access
dm stripe: add DAX support
dm error: add DAX support
dm linear: add DAX support
dm: add infrastructure for DAX support
dm thin: fix a race condition between discarding and provisioning a block
dm btree: fix a bug in dm_btree_find_next_single()
dm raid: fix random optimal_io_size for raid0
dm raid: address checkpatch.pl complaints
dm: call PR reserve/unreserve on each underlying device
sd: don't use the ALL_TG_PT bit for reservations
dm: fix second blk_delay_queue() parameter to be in msec units not jiffies
dm raid: change logical functions to actually return bool
dm raid: use rdev_for_each in status
dm raid: use rs->raid_disks to avoid memory leaks on free
dm raid: support delta_disks for raid1, fix table output
dm raid: enhance reshape check and factor out reshape setup
dm raid: allow resize during recovery
dm raid: fix rs_is_recovering() to allow for lvextend
...
Allow table type DM_TYPE_BIO_BASED to extend with DM_TYPE_DAX_BIO_BASED
since DM_TYPE_DAX_BIO_BASED supports bio-based requests.
This is needed to allow a snapshot of an LV with DAX support to be
removed. One of the intermediate table reloads that lvm2 does switches
from DM_TYPE_BIO_BASED to DM_TYPE_DAX_BIO_BASED. No known reason to
disallow this so...
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dax-capable mapped-device is marked as DM_TYPE_DAX_BIO_BASED,
which supports both dax and bio-based operations. dm-snap
needs to work with dax-capable device when bio-based operation
is used.
Add fake origin_direct_access() to origin device so that its
origin device is also marked as DM_TYPE_DAX_BIO_BASED for
dax-capable device. This allows to extend target's DM table.
dm-snap works normally when bio-based operation is used.
dm-snap does not support dax operation, and mount with dax
option to a target device or snapshot device fails.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Change dm-stripe to implement direct_access function,
stripe_direct_access(), which maps bdev and sector and
calls direct_access function of its physical target device.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Change dm-linear to implement direct_access function,
linear_direct_access(), which maps sector and calls direct_access
function of its physical target device.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Change mapped device to implement direct_access function,
dm_blk_direct_access(), which calls a target direct_access function.
'struct target_type' is extended to have target direct_access interface.
This function limits direct accessible size to the dm_target's limit
with max_io_len().
Add dm_table_supports_dax() to iterate all targets and associated block
devices to check for DAX support. To add DAX support to a DM target the
target must only implement the direct_access function.
Add a new dm type, DM_TYPE_DAX_BIO_BASED, which indicates that mapped
device supports DAX and is bio based. This new type is used to assure
that all target devices have DAX support and remain that way after
QUEUE_FLAG_DAX is set in mapped device.
At initial table load, QUEUE_FLAG_DAX is set to mapped device when setting
DM_TYPE_DAX_BIO_BASED to the type. Any subsequent table load to the
mapped device must have the same type, or else it fails per the check in
table_load().
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Instead of a flag and an index just make sure an index of 0 means
no need to free the bvec array. Also move the constants related
to the bvec pools together and use a consistent naming scheme for
them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
These two are confusing leftover of the old world order, combining
values of the REQ_OP_ and REQ_ namespaces. For callers that don't
special case we mostly just replace bi_rw with bio_data_dir or
op_is_write, except for the few cases where a switch over the REQ_OP_
values makes more sense. Any check for READA is replaced with an
explicit check for REQ_RAHEAD. Also remove the READA alias for
REQ_RAHEAD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The discard passdown was being issued after the block was unmapped,
which meant the block could be reprovisioned whilst the passdown discard
was still in flight.
We can only identify unshared blocks (safe to do a passdown a discard
to) once they're unmapped and their ref count hits zero. Block ref
counts are now used to guard against concurrent allocation of these
blocks that are being discarded. So now we unmap the block, issue
passdown discards, and the immediately increment ref counts for regions
that have been discarded via passed down (this is safe because
allocation occurs within the same thread). We then decrement ref counts
once the passdown discard IO is complete -- signaling these blocks may
now be allocated.
This fixes the potential for corruption that was reported here:
https://www.redhat.com/archives/dm-devel/2016-June/msg00311.html
Reported-by: Dennis Yang <dennisyang@qnap.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm_btree_find_next_single() can short-circuit the search for a block
with a return of -ENODATA if all entries are higher than the search key
passed to lower_bound().
This hasn't been a problem because of the way the btree has been used by
DM thinp. But it must be fixed now in preparation for fixing the race
in DM thinp's handling of simultaneous block discard vs allocation.
Otherwise, once that fix is in place, some of the blocks in a discard
would not be unmapped as expected.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
RAID10 random read performance is lower than expected due to excessive spinlock
utilisation which is required mostly for rebuild/resync. Simplify allow_barrier
as it's in IO path and encounters a lot of unnecessary congestion.
As lower_barrier just takes a lock in order to decrement a counter, convert
counter (nr_pending) into atomic variable and remove the spin lock. There is
also a congestion for wake_up (it uses lock internally) so call it only when
it's really needed. As wake_up is not called constantly anymore, ensure process
waiting to raise a barrier is notified when there are no more waiting IOs.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Changeset 6791875e2e has added early return from a function so there is no
sysfs notification for 'active' and 'clean' state change.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
md loads raidX modules and increments module refcount each time level
has changed but does not decrement it. You are unable to unload raid0
module after reshape because raid0 reshape changes level to raid4
and back to raid0.
Signed-off-by: Aleksey Obitotskiy <aleksey.obitotskiy@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The md code stores the exact time of the last error in the
last_read_error variable using a timespec structure. It only
ever uses the seconds portion of that though, so we can
use a scalar for it.
There won't be an overflow in 2038 here, because it already
used monotonic time and 32-bit is enough for that, but I've
decided to use time64_t for consistency in the conversion.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shaohua Li <shli@fb.com>
raid_io_hints() was retrieving the number of data stripes used for the
calculation of io_opt from struct r5conf, which is not defined for raid0
mappings.
Base the calculation on the in-core raid_set structure instead.
Also, adjust to use to_bytes() for the sector -> bytes conversion
throughout.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use 'unsigned int' where appropriate.
Return negative errors.
Correct an indentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
So far we tried to rely on the SCSI 'all target ports' bit to register
all path, but for many setups this didn't work properly as the different
paths are seen as separate initiators to the target instead of multiple
ports of the same initiator. Because of that we'll stop setting the
'all target ports' bit in SCSI, and let device mapper handle iterating
over the device for each path and register them manually.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit d548b34b06 ("dm: reduce the queue delay used in dm_request_fn
from 100ms to 10ms") always intended the value to be 10 msecs -- it
just expressed it in jiffies because earlier commit 7eaceaccab ("block:
remove per-queue plugging") did.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fixes: d548b34b06 ("dm: reduce the queue delay used in dm_request_fn from 100ms to 10ms")
Cc: stable@vger.kernel.org # 4.1+ -- stable@ backports must be applied to drivers/md/dm.c
Add "delta_disks" constructor argument support to raid1 to allow for
consistent userspace disk addition/removal handling.
Fix raid_status() to report all raid disks with status and table output
on disk adding reshapes, not just the ones listed on the mddev; optimize
its rebuild and writemostly output.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Enhance rs_reshape_requested() check function to be more transparent and
fix its raid10 check.
Streamline the constructor by factoring out reshaping preparation into
fucntion rs_prepare_reshape().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Resizing a RAID set during recovery can be allowed, because the MD
resynchronization thread will either stop any ongoing recovery in case
of shrinking below the current recovery position or carry on recovery
to the new size if the set is growing.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add function rs_setup_recovery() to allow for defined setup of RAID set
recovery in the constructor.
Will be called with dev_sectors={0, rdev->sectors, MaxSectors} to
recover a new or enforced sync, grown or not to be synhronized RAID set
respectively.
Prevents recovery on raid0, which doesn't support it.
Enforces recovery on raid6 to ensure properly defined Syndromes
mandatory for that MD personality are being created.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Check return value of kthread_run() in dm_old_init_request_queue().
Reported-by: Minfei Huang <mnghuan@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
We have assigned sb->block_size before the switch,
so remove the redundant one.
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Eric Wheeler <bcache@lists.ewheeler.net>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is no return in continue_at(), update the documentation.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Cache_sb is not used in cache_alloc, and we have copied
sb info to cache->sb already, remove it.
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
do_div was replaced with div64_u64 at some point, causing a bug with
block calculation due to incompatible semantics of the two functions.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Fixes: a739ff3f54 ("dm verity: add support for forward error correction")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Merge the two DM_PARAMS_[KV]MALLOC flags into a single flag.
Doing so avoids the crashes seen with previous attempts to consolidate
buffer management to use kvfree() without first flagging that memory had
actually been allocated.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Avoid that sparse complains about assigning a __le64 value to a u64
variable. Remove the (u64) casts since these are superfluous. This
patch does not change the behavior of the source code.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A newly introduced function has 'const int' as the return type,
but as "make W=1" reports, that has no meaning:
drivers/md/dm-raid.c:510:18: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
This changes the return type to plain 'int'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 33e53f0685 ("dm raid: introduce extended superblock and new raid types to support takeover/reshaping")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Superblock updates where bogus causing some takovers/reshapes to fail.
Introduce new runtime flag (RT_FLAG_KEEP_RS_FROZEN) to keep a raid set
frozen when a layout change was requested. Userpace will immediately
reload the table w/o the flags requesting such change once they made it
to the superblocks and any change of recovery/reshape offsets has to be
avoided until after read.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add bool functions rs_is_recovering and rs_is_reshaping()
to test for ongoing recovery/reshaping respectively in order
to reject respective requests on ongoing ones.
Remove ctr array size check, because ti->len and array
sectors will differ during disk addition/removal reshape.
Use __is_raid10_near() rather than type string compare.
Introduce rs_check_reshape() and rs_start_reshape(),
use the former in the ctr to reject bogus rehsape requests
and the latter in preresume to actually start a reshape.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add rs_is_reshapable(), rs_data_stripes(), rs_reshape_requested(),
rs_set_dev_and_array_sectors() and rs_adjust_data_offsets()
Remove superfluous check for reshape message
Correct runtime bit definitions to be incremental
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
It is more intuitive to manage each raid level's features in terms of
what is supported rather than what isn't supported.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Renamed functions and variables with leading single underscore to have a
double underscore. Renamed some functions to have better names. Folded
functions that were split out without reason.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Also update module description to "raid0/1/10/4/5/6 target"
Reported by Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
No idea what Heinz was doing with the versioning but upstream commit
4c9971ca6a ("dm raid: make sure no feature flags are set in metadata")
bumped to 1.8.0 already.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There ti_error_* wrappers added very little. No other DM target has
ever gone to such lengths to wrap setting ti->error.
Also fixes some NULL derefences via rs->ti->error.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The target's status interface has to provide the new 'data_offset' value
to allow userspace to retrieve the kernels offset to the data on each
raid device of a raid set. This is the base for out-of-place reshaping
required to not write over any data during reshaping (e.g. change
raid6_zr -> raid6_nc):
- add rs_set_cur() to be able to start up existing array in case of no
takeover; use in ctr on takeover check
- enhance raid_status()
- add supporting functions to get resync/reshape progress and raid
device status chars
- fixup rebuild table line output race, which does miss to emit
'rebuild N' on fully synced/rebuild devices, because it is relying on
the transient 'In_sync' raid device flag
- add new status line output for 'data_offset', which'll later be used
for out-of-place reshaping
- fixup takeover not working for all levels
- fixup raid0 message interface oops caused by missing checks
for the md threads, which don't exist in case of raid0
- remove ALL_FREEZE_FLAGS not needed for takeover
- adjust comments
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add raid level takeover support allowing arbitrary takeovers between
raid levels supported by md personalities (i.e. raid0, raid1/10 and
raid4/5/6):
- add rs_config_{backup|restore} function to allow for temporary
storing ctr requested layout changes and restore them for takeover
conersion decision after the superblocks got loaded and analyzed
- add members to store layout to 'struct raid_set' (not mandatory
for takeover but needed for reshape in later patch)
- add rebuild_disks bitfield to 'struct raid_set' and set bits in ctr
to use in setting up takeover (base to address a 'rebuild' related
raid_status() table line bug and needed as well for reshape in future
patch)
- add runtime flags and respective manipulation functions to be able to
control e.g. wrting of superlocks to the preresume function on
takeover and (later) reshape
- add functions to detect takeover, check it's valid (mandatory here to
avoid failing on md_run()), setup for it and use in the ctr; those
will be likely moved out once reshaping gets added to simplify the
ctr
- start raid set readonly in ctr and switch to readwrite, optionally
updating superblocks, in preresume in order to allow suspend to
quiesce any active table before (which involves superblock updates);
this ensures the proper sequence of writing the current and any new
takeover(/reshape) metadata
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add transferring the new takeover/reshape related superblock
members introduced to the super_sync() function:
- add/move supporting functions
- add failed devices bitfield transfer functions to retrieve the
bitfield from superblock format or update it in the superblock
- add code to transfer all new members
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Support the follwoing arguments in the ctr parameter parser:
- add 'delta_disks', 'data_offset' taking int and sector respectively
- 'raid10_use_near_sets' bool argument to optionally select
near sets with supporting raid10 mappings
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add new members to the dm-raid superblock and new raid types to support
takeover/reshape.
Add all necessary members needed to support takeover and reshape in one
go -- aiming to limit the amount of changes to the superblock layout.
This is a larger patch due to the new superblock members, their related
flags, validation of both and involved API additions/changes:
- add additional members to keep track of:
- state about forward/backward reshaping
- reshape position
- new level, layout, stripe size and delta disks
- data offset to current and new data for out-of-place reshapes
- failed devices bitfield extensions to keep track of max raid devices
- adjust super_validate() to cope with new superblock members
- adjust super_init_validation() to cope with new superblock members
- add definitions for ctr flags supporting delta disks etc.
- add new raid types (raid6_n_6 etc.)
- add new raid10 supporting function API (_is_raid10_*())
- adjust to changed raid10 supporting function API
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Every time a device is removed with ->hot_remove_disk() a synchronize_rcu() call is made
which can delay several milliseconds in some case.
If lots of devices fail at once - as could happen with a large RAID10 where one set
of devices are removed all at once - these delays can add up to be very inconcenient.
As failure is not reversible we can check for that first, setting a
separate flag if it is found, and then all synchronize_rcu() once for
all the flagged devices. Then ->hot_remove_disk() function can skip the
synchronize_rcu() step if the flag is set.
fix build error(Shaohua)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
It is important that we never increment rdev->nr_pending on a Faulty
device as ->hot_remove_disk() assumes that once the Faulty flag is visible
no code will take a new reference.
Some places take a new reference after only check In_sync. This should
be safe as the two are changed together. However to make the code more
obviously safe, add checks for 'Faulty' as well.
Note: the actual rule is:
Never increment nr_pending if Faulty is set and Blocked is clear,
never clear Faulty, and never set Blocked without holding a reference
through nr_pending.
fix build error (Shaohua)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Being in the middle of resync is no longer protection against failed
rdevs disappearing. So add rcu protection.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The rdev could be freed while handle_failed_sync is running, so
rcu protection is needed.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Since remove_and_add_spares() was added to hot_remove_disk() it has
been possible for an rdev to be hot-removed while fix_read_error()
was running, so we need to be more careful, and take a reference to
the rdev while performing IO.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
'mirror' is only used to find 'rdev', several times.
So just find 'rdev' once, and use it instead.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Both functions use conf->mirrors[mirror].rdev several times, so
improve readability by storing this in a local variable.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
'tmp' is only ever used to extract 'tmp->rdev', so just use 'rdev' directly.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
rdev already holds conf->mirrors[d].rdev, so no need to load it again.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
mirrors[].rdev can become NULL at any point unless:
- a counted reference is held
- ->reconfig_mutex is held, or
- rcu_read_lock() is held
Reshape isn't always suitably careful as in the past rdev couldn't be
removed during reshape. It can now, so add protection.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
mirrors[].rdev can become NULL at any point unless:
- a counted reference is held
- ->reconfig_mutex is held, or
- rcu_read_lock() is held
Previously they could not become NULL during a resync/recovery/reshape either.
However when remove_and_add_spares() was added to hot_remove_disk(), that
changed.
So raid10_sync_request didn't previously need to protect rdev access,
but now it does.
Fix missed check(Shaohua)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
mirrors[].rdev can become NULL at any point unless:
- a counted reference is held
- ->reconfig_mutex is held, or
- rcu_read_lock() is held
raid10_status holds none of these. So add rcu_read_lock()
protection.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If you have a raid10 with a replacement device that is resyncing -
e.g. after a crash before the replacement was complete - the write to
the replacement will increment nr_pending on the wrong device, which
will lead to strangeness.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Re-checking the faulty flag here brings no value.
The comment about "risk" refers to the risk that the device could
be in the process of being removed by ->hot_remove_disk().
However providing that the ->nr_pending count is incremented inside
an rcu_read_locked() region, there is no risk of that happening.
This is because the rdev pointer (in the personalities array) is set
to NULL before synchronize_rcu(), and ->nr_pending is tested
afterwards. If the rcu_read_locked region happens before the
synchronize_rcu(), the test will see that nr_pending has been incremented.
If it happens afterwards, the rdev pointer will be NULL so there is nothing
to increment.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When the HOT_REMOVE_DISK ioctl is used to remove a device, we
call remove_and_add_spares() which will remove it from the personality
if possible. This improves the chances that the removal will succeed.
When writing "remove" to dev-XX/state, we don't. So that can fail more easily.
So add the remove_and_add_spares() into "remove" handling.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
A performance drop of mkfs has been observed on RAID10 during resync
since commit 09314799e4 ("md: remove 'go_faster' option from
->sync_request()"). Resync sends so many IOs it slows down non-resync
IOs significantly (few times). Add a short delay to a resync. The
previous long sleep (1s) has proven unnecessary, even very short delay
brings performance right.
The change also applied to raid1. The problem has not been observed on
raid1, however it shares barriers code with raid10 so it might be an
issue for some setup too.
Suggested-by: NeilBrown <neilb@suse.com>
Link: http://lkml.kernel.org/r/20160609134555.GA9104@proton.igk.intel.com
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
This is a simple check before updating the superblock. It should update
the superblock when update_size return 0.
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Make use if raid type rt_is_*() bool functions for simplification and
consistency reasons.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- add _test_flags() function
- use it to simplify rs_check_for_invalid_flags()
- use _test_flag() throughout
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reject invalid flag combinations to avoid potential data corruption or
failing raid set construction:
- add definitions for constructor flag combinations and invalid flags
per level
- add bool test functions for the various raid types
(also will be used by future reshaping enhancements)
- introduce rs_check_for_invalid_flags() and _invalid_flags()
to perform the validity checks
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Provide necessary infrastructure to handle ctr flags and their names
and cleanup setting ti->error:
- comment constructor flags
- introduce constructor flag manipulation
- introduce ti_error_*() functions to simplify
setting the error message (use in other targets?)
- introduce array to hold ctr flag <-> flag name mapping
- introduce argument name by flag functions for that array
- use those functions throughout the ctr call path
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- use dm_arg_set API in ctr and its callees parse_raid_params() and dev_parms()
- introduce _in_range() function to check a value is in a [ min, max ] range;
this is to support more callers in parsing parameters etc. in the future
- correct comment on MAX_RAID_DEVICES
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
alloc_workqueue replaces deprecated create_workqueue().
Dedicated workqueues have been used since bcache_wq and moving_gc_wq
are workqueues for writes and are being used on a memory reclaim path.
WQ_MEM_RECLAIM has been set to ensure forward progress under memory
pressure.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow a user to specify an optional feature 'queue_mode <mode>' where
<mode> may be "bio", "rq" or "mq" -- which corresponds to bio-based,
request_fn rq-based, and blk-mq rq-based respectively.
If the queue_mode feature isn't specified the default for the
"multipath" target is still "rq" but if dm_mod.use_blk_mq is set to Y
it'll default to mode "mq".
This new queue_mode feature introduces the ability for each multipath
device to have its own queue_mode (whereas before this feature all
multipath devices effectively had to have the same queue_mode).
This commit also goes a long way to eliminate the awkward (ab)use of
DM_TYPE_*, the associated filter_md_type() and other relatively fragile
and difficult to maintain code.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add "multipath-bio" target that offers a bio-based multipath target as
an alternative to the request-based "multipath" target -- but in a
following commit "multipath-bio" will immediately be replaced by a new
"queue_mode" feature for the "multipath" target which will allow
bio-based mode to be selected.
When DM multipath was originally converted from bio-based to
request-based the motivation for the change was better dynamic load
balancing (by leveraging block core's request-based IO schedulers, for
merging and sorting, _before_ DM multipath would make the decision on
where to steer the IO -- based on path load and/or availability).
More background is available in this "Request-based Device-mapper
multipath and Dynamic load balancing" paper:
https://www.kernel.org/doc/ols/2007/ols2007v2-pages-235-244.pdf
But we've now come full circle where significantly faster storage
devices no longer need IOs to be made larger to drive optimal IO
performance. And even if they do there have been changes to the block
and filesystem layers that help ensure upper layers are constructing
larger IOs. In addition, SCSI's differentiated IO errors will propagate
through to bio-based IO completion hooks -- so that eliminates another
historic justiciation for request-based DM multipath. Lastly, the block
layer's immutable biovec changes have made bio cloning cheaper than it
has ever been; whereas request cloning is still relatively expensive
(both on a CPU usage and memory footprint level).
As such, bio-based DM multipath offers the promise of a more efficient
IO path for high IOPs devices that are, or will be, emerging.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add some seperation between bio-based and request-based DM core code.
'struct mapped_device' and other DM core only structures and functions
have been moved to dm-core.h and all relevant DM core .c files have been
updated to include dm-core.h rather than dm.h
DM targets should _never_ include dm-core.h!
[block core merge conflict resolution from Stephen Rothwell]
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Instead of overloading the discard support with the REQ_SECURE flag.
Use the opportunity to rename the queue flag as well, and remove the
dead checks for this flag in the RAID 1 and RAID 10 drivers that don't
claim support for secure erase.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds a REQ_OP_FLUSH operation that is sent to request_fn
based drivers by the block layer's flush code, instead of
sending requests with the request->cmd_flags REQ_FLUSH bit set.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We don't need bi_rw to be so large on 64 bit archs, so
reduce it to unsigned int.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The req operation REQ_OP is separated from the rq_flag_bits
definition. This converts the block layer drivers to
use req_op to get the op from the request struct.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have md
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have bcache
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have dm
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It looks like dm stats cares about the data direction
(READ vs WRITE) and does not need the bio/request flags.
Commands like REQ_FLUSH, REQ_DISCARD and REQ_WRITE_SAME
are currently always set with REQ_WRITE, so the extra check for
REQ_DISCARD in dm_stats_account_io is not needed.
This patch has it use the bio and request data_dir helpers
instead of accessing the bi_rw/cmd_flags directly. This makes
the next patches that remove the operation from the cmd_flags
and bi_rw easier, because we will no longer have the REQ_WRITE
bit set for operations like discards.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This converts the block issue discard helper and users to use
the bio_set_op_attrs accessor and only pass in the operation flags
like REQ_SEQURE.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We currently set REQ_WRITE/WRITE for all non READ IOs
like discard, flush, writesame, etc. In the next patches where we
no longer set up the op as a bitmap, we will not be able to
detect a operation direction like writesame by testing if REQ_WRITE is
set.
This has bcache use the op_is_write helper which will do the right
thing.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We currently set REQ_WRITE/WRITE for all non READ IOs
like discard, flush, writesame, etc. In the next patches where we
no longer set up the op as a bitmap, we will not be able to
detect a operation direction like writesame by testing if REQ_WRITE is
set.
This has dm use the op_is_write helper which will do the right
thing.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has submit_bh users pass in the operation and flags separately,
so submit_bh_wbc can setup the bio op and bi_rw flags on the bio that
is submitted.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
Add a disk to an array which is performing recovery
is a little complicated, we need to do both reap the
sync thread and perform add disk for the case, then
it caused deadlock as follows.
linux44:~ # ps aux|grep md|grep D
root 1822 0.0 0.0 0 0 ? D 16:50 0:00 [md127_resync]
root 1848 0.0 0.0 19860 952 pts/0 D+ 16:50 0:00 mdadm --manage /dev/md127 --re-add /dev/vdb
linux44:~ # cat /proc/1848/stack
[<ffffffff8107afde>] kthread_stop+0x6e/0x120
[<ffffffffa051ddb0>] md_unregister_thread+0x40/0x80 [md_mod]
[<ffffffffa0526e45>] md_reap_sync_thread+0x15/0x150 [md_mod]
[<ffffffffa05271e0>] action_store+0x260/0x270 [md_mod]
[<ffffffffa05206b4>] md_attr_store+0xb4/0x100 [md_mod]
[<ffffffff81214a7e>] sysfs_write_file+0xbe/0x140
[<ffffffff811a6b98>] vfs_write+0xb8/0x1e0
[<ffffffff811a75b8>] SyS_write+0x48/0xa0
[<ffffffff8152a5c9>] system_call_fastpath+0x16/0x1b
[<00007f068ea1ed30>] 0x7f068ea1ed30
linux44:~ # cat /proc/1822/stack
[<ffffffffa05251a6>] md_do_sync+0x846/0xf40 [md_mod]
[<ffffffffa052402d>] md_thread+0x16d/0x180 [md_mod]
[<ffffffff8107ad94>] kthread+0xb4/0xc0
[<ffffffff8152a518>] ret_from_fork+0x58/0x90
Task1848 Task1822
md_attr_store (held reconfig_mutex by call mddev_lock())
action_store
md_reap_sync_thread
md_unregister_thread
kthread_stop md_wakeup_thread(mddev->thread);
wait_event(mddev->sb_wait, !test_bit(MD_CHANGE_PENDING))
md_check_recovery is triggered by wakeup mddev->thread,
but it can't clear MD_CHANGE_PENDING flag since it can't
get lock which was held by md_attr_store already.
To solve the deadlock problem, we move "->resync_finish()"
from md_do_sync to md_reap_sync_thread (after md_update_sb),
also MD_HELD_RESYNC_LOCK is introduced since it is possible
that node can't get resync lock in md_do_sync.
Then we do not need to wait for MD_CHANGE_PENDING is cleared
or not since metadata should be updated after md_update_sb,
so just call resync_finish if MD_HELD_RESYNC_LOCK is set.
We also unified the code after skip label, since set PENDING
for non-clustered case should be harmless.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull block fixes from Jens Axboe:
"A set of fixes that wasn't included in the first merge window pull
request. This pull request contains:
- A set of NVMe fixes from Keith, and one from Nic for the integrity
side of it.
- Fix from Ming, clearing ->mq_ops if we don't successfully setup a
queue for multiqueue.
- A set of stability fixes for bcache from Jiri, and also marking
bcache as orphaned as it's no longer actively maintained (in
mainline, at least)"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: clear q->mq_ops if init fail
MAINTAINERS: mark bcache as orphan
bcache: bch_gc_thread() is not freezable
bcache: bch_allocator_thread() is not freezable
bcache: bch_writeback_thread() is not freezable
nvme/host: Add missing blk_integrity tag_size + flags assignments
NVMe: Add device ID's with stripe quirk
NVMe: Short-cut removal on surprise hot-unplug
NVMe: Allow user initiated rescan
NVMe: Reduce driver log spamming
NVMe: Unbind driver on failure
NVMe: Delete only created queues
NVMe: Allocate queues only for online cpus
In current handle_stripe_dirtying, the code prefers rmw with
PARITY_ENABLE_RMW; while prefers rcw with PARITY_PREFER_RMW.
This patch reverses this behavior.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
bch_gc_thread() doesn't mark itself freezable, so calling try_to_freeze()
in its context is just an expensive no-op.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
bch_allocator_thread() is calling try_to_freeze(), but that's just an
expensive no-op given the fact that the thread is not marked freezable.
Bucket allocator has to be up and running to the very last stages of the
suspend, as the bcache I/O that's in flight (think of writing an
hibernation image to a swap device served by bcache).
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
bch_writeback_thread() is calling try_to_freeze(), but that's just an
expensive no-op given the fact that the thread is not marked freezable.
I/O helper kthreads, exactly such as the bcache writeback thread, actually
shouldn't be freezable, because they are potentially necessary for
finalizing the image write-out.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull MD updates from Shaohua Li:
"Several patches from Guoqing fixing md-cluster bugs and several
patches from Heinz fixing dm-raid bugs"
* tag 'md/4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md-cluster: check the return value of process_recvd_msg
md-cluster: gather resync infos and enable recv_thread after bitmap is ready
md: set MD_CHANGE_PENDING in a atomic region
md: raid5: add prerequisite to run underneath dm-raid
md: raid10: add prerequisite to run underneath dm-raid
md: md.c: fix oops in mddev_suspend for raid0
md-cluster: fix ifnullfree.cocci warnings
md-cluster/bitmap: unplug bitmap to sync dirty pages to disk
md-cluster/bitmap: fix wrong page num in bitmap_file_clear_bit and bitmap_file_set_bit
md-cluster/bitmap: fix wrong calcuation of offset
md-cluster: sync bitmap when node received RESYNCING msg
md-cluster: always setup in-memory bitmap
md-cluster: wakeup thread if activated a spare disk
md-cluster: change array_sectors and update size are not supported
md-cluster: fix locking when node joins cluster during message broadcast
md-cluster: unregister thread if err happened
md-cluster: wake up thread to continue recovery
md-cluser: make resync_finish only called after pers->sync_request
md-cluster: change resync lock from asynchronous to synchronous
bio_inc_remaining() and the block core's new async
__blkdev_issue_discard() interface
- make DM multipath's fast code-paths lockless, using lockless_deference,
to significantly improve large NUMA performance when using blk-mq. The
m->lock spinlock contention was a serious bottleneck.
- a few other small code cleanups and Documentation fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXNdGVAAoJEMUj8QotnQNaYYgH/Rf2am46A78kcR5b9nN2I+Tb
+MkqQyf8mXUzNHOu3v93CVugT+tBZuJcpHPJgCSc/1GXtgsjHLvbkO2Mc+Ioe45S
PlUA3HdRzxHSJ365SdYvT+bY+QQlGiySelSBrJHlikXC88kz3wqyQ146BT1Rw/w+
t0mi1liNJtZHsuH+3uO9uxe5+H7476lB84i79Kz0x8Ygv5+urgaSvDBRO5EH/hkJ
LN2WJWHDQLT4MtHKCuiMiLpu/1HGvISN2QrMPsFjC1d1DbbZvRWAxYDwGaP/C277
IflPo7sA/nds5T2vqb0fRTPuxBnzXdFMMvf+VQX7pjCnxlhfaxBkvNtnFpxW+oA=
=iCyS
-----END PGP SIGNATURE-----
Merge tag 'dm-4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- based on Jens' 'for-4.7/core' to have DM thinp's discard support use
bio_inc_remaining() and the block core's new async __blkdev_issue_discard()
interface
- make DM multipath's fast code-paths lockless, using lockless_deference,
to significantly improve large NUMA performance when using blk-mq.
The m->lock spinlock contention was a serious bottleneck.
- a few other small code cleanups and Documentation fixes
* tag 'dm-4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: unroll issue_discard() to create longer discard bio chains
dm thin: use __blkdev_issue_discard for async discard support
dm thin: remove __bio_inc_remaining() and switch to using bio_inc_remaining()
dm raid: make sure no feature flags are set in metadata
dm ioctl: drop use of __GFP_REPEAT in copy_params()'s __vmalloc() call
dm stats: fix spelling mistake in Documentation
dm cache: update cache-policies.txt now that mq is an alias for smq
dm mpath: eliminate use of spinlock in IO fast-paths
dm mpath: move trigger_event member to the end of 'struct multipath'
dm mpath: use atomic_t for counting members of 'struct multipath'
dm mpath: switch to using bitops for state flags
dm thin: Remove return statement from void function
dm: remove unused mapped_device argument from free_tio()
Pull block driver updates from Jens Axboe:
"On top of the core pull request, this is the drivers pull request for
this merge window. This contains:
- Switch drivers to the new write back cache API, and kill off the
flush flags. From me.
- Kill the discard support for the STEC pci-e flash driver. It's
trivially broken, and apparently unmaintained, so it's safer to
just remove it. From Jeff Moyer.
- A set of lightnvm updates from the usual suspects (Matias/Javier,
and Simon), and fixes from Arnd, Jeff Mahoney, Sagi, and Wenwei
Tao.
- A set of updates for NVMe:
- Turn the controller state management into a proper state
machine. From Christoph.
- Shuffling of code in preparation for NVMe-over-fabrics, also
from Christoph.
- Cleanup of the command prep part from Ming Lin.
- Rewrite of the discard support from Ming Lin.
- Deadlock fix for namespace removal from Ming Lin.
- Use the now exported blk-mq tag helper for IO termination.
From Sagi.
- Various little fixes from Christoph, Guilherme, Keith, Ming
Lin, Wang Sheng-Hui.
- Convert mtip32xx to use the now exported blk-mq tag iter function,
from Keith"
* 'for-4.7/drivers' of git://git.kernel.dk/linux-block: (74 commits)
lightnvm: reserved space calculation incorrect
lightnvm: rename nr_pages to nr_ppas on nvm_rq
lightnvm: add is_cached entry to struct ppa_addr
lightnvm: expose gennvm_mark_blk to targets
lightnvm: remove mgt targets on mgt removal
lightnvm: pass dma address to hardware rather than pointer
lightnvm: do not assume sequential lun alloc.
nvme/lightnvm: Log using the ctrl named device
lightnvm: rename dma helper functions
lightnvm: enable metadata to be sent to device
lightnvm: do not free unused metadata on rrpc
lightnvm: fix out of bound ppa lun id on bb tbl
lightnvm: refactor set_bb_tbl for accepting ppa list
lightnvm: move responsibility for bad blk mgmt to target
lightnvm: make nvm_set_rqd_ppalist() aware of vblks
lightnvm: remove struct factory_blks
lightnvm: refactor device ops->get_bb_tbl()
lightnvm: introduce nvm_for_each_lun_ppa() macro
lightnvm: refactor dev->online_target to global nvm_targets
lightnvm: rename nvm_targets to nvm_tgt_type
...
There is little benefit to doing this but it does structure DM thinp's
code to more cleanly use the __blkdev_issue_discard() interface --
particularly in passdown_double_checking_shared_status().
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
With commit 38f2525533 ("block: add __blkdev_issue_discard") DM thinp
no longer needs to carry its own async discard method.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
DM thinp's use of bio_inc_remaining() is critical to ensure the original
parent discard bio isn't completed before sub-discards have. DM thinp
needs this due to the extra quiescing that occurs, via multiple DM thinp
mappings, while processing large discards. As such DM thinp must build
the async discard bio chain after some delay -- so bio_inc_remaining()
is used to enable DM thinp to take a reference on the original parent
discard bio for each mapping. This allows the immediate use of
bio_endio() on that discard bio; but with the understanding that the
actual completion won't occur until each of the sub-discards'
per-mapping references are dropped.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Given we don't yet support any feature flags in the dm-raid ondisk
metadata (see: 'features' member of 'struct dm_raid_superblock'),
add a check to ensure no flags are actually set, if any features are
set reject the activation of the RAID mapping.
This is to prevent possible data corruption in case of a kernel
downgrade when there'll potentially be feature flags set by a future
dm-raid target.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
We don't need to run the full path of recv_daemon
if process_recvd_msg doesn't return 0.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The in-memory bitmap is not ready when node joins cluster,
so it doesn't make sense to make gather_all_resync_info()
called so earlier, we need to call it after the node's
bitmap is setup. Also, recv_thread could be wake up after
node joins cluster, but it could cause problem if node
receives RESYNCING message without persionality since
mddev->pers->quiesce is called in process_suspend_info.
This commit introduces a new cluster interface load_bitmaps
to fix above problems, load_bitmaps is called in bitmap_load
where bitmap and persionality are ready, and load_bitmaps
does the following tasks:
1. call gather_all_resync_info to load all the node's
bitmap info.
2. set MD_CLUSTER_ALREADY_IN_CLUSTER bit to recv_thread
could be wake up, and wake up recv_thread if there is
pending recv event.
Then ack_bast only wakes up recv_thread after IN_CLUSTER
bit is ready otherwise MD_CLUSTER_PENDING_RESYNC_EVENT is
set.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
