Need to use broadcast sta_id for management frames, otherwise we broke
BA session in the firmware and get messages like that:
"Received BA when not expected"
or (on older kernels):
"BA scd_flow 0 does not match txq_id 10"
This fix regression introduced in 2.6.35 during station management
code rewrite by:
commit 2a87c26bbe
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Apr 30 11:30:45 2010 -0700
iwlwifi: use iwl_find_station less
Patch partially resolve:
https://bugzilla.kernel.org/show_bug.cgi?id=16691
However, there are still 11n performance problems on 4965 and 5xxx
devices that need to be investigated.
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a rescuer and stop_machine() bringing down a CPU race with each
other, they may deadlock on non-preemptive kernel. The CPU won't
accept a new task, so the rescuer can't migrate to the target CPU,
while stop_machine() can't proceed because the rescuer is holding one
of the CPU retrying migration. GCWQ_DISASSOCIATED is never cleared
and worker_maybe_bind_and_lock() retries indefinitely.
This problem can be reproduced semi reliably while the system is
entering suspend.
http://thread.gmane.org/gmane.linux.kernel/1122051
A lot of kudos to Thilo-Alexander for reporting this tricky issue and
painstaking testing.
stable: This affects all kernels with cmwq, so all kernels since and
including v2.6.36 need this fix.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Thilo-Alexander Ginkel <thilo@ginkel.com>
Tested-by: Thilo-Alexander Ginkel <thilo@ginkel.com>
Cc: stable@kernel.org
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3+: voltage: remove initial voltage
OMAP4: Intialize IVA Device in addition to DSP device.
omap: rx51: mark reserved memory earlier
OMAP3: l3: fix for "irq 10: nobody cared" message
arm: omap2: enable smc instruction for sleep34xx
OMAP2/3: hwmod: fix gpio-reset timeouts seen during bootup.
OMAP3: PM: Do not rely on ROM code to restore CM_AUTOIDLE_PLL.AUTO_PERIPH_DPLL
OMAP2+: PM: Fix the saving of CM_AUTOIDLE_PLL register on scratchpad area
OMAP4: clock data: Change DSS clock aliases
OMAP2+: hwmod data: Fix wrong dma_system end address
When CONFIG_OABI_COMPAT is set, the wrapper for semtimedop does not
bound the nsops argument. A sufficiently large value will cause an
integer overflow in allocation size, followed by copying too much data
into the allocated buffer. Fix this by restricting nsops to SEMOPM.
Untested.
Cc: stable@kernel.org
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We must remove all files we created, even in error cases.
Fixes second part of kernel bug #34072:
https://bugzilla.kernel.org/show_bug.cgi?id=34072
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Recent Xeon processor thermal sensors are supported by the coretemp
driver and not the adm1021 driver. Only one old generation of Xeon
processors (the first Netburst ones) are supported by the adm1021
driver.
Reported-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The lm90 driver's attribute update interval is configurable.
Reflect this information in the driver documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for ADT7461A and NCT1008 to the lm90 driver.
Both chips have identical functionality and report the same manufacturing ID
and device ID values.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The PCI SSID is 1025:031c and the codec SSID is 1025:031d,
so the driver mistakes this for a SKU value, but looking at
the numbers, this is obviously wrong.
Cc: stable@kernel.org (2.6.38+)
BugLink: http://bugs.launchpad.net/bugs/761861
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sedat and Bruno reported RCU stalls which turned out to be caused by
the following;
sched_init() calls init_rt_bandwidth() which calls hrtimer_init()
_BEFORE_ hrtimers_init() is called. While not entirely correct this
worked because hrtimer_init() only accessed statically initialized
data (hrtimer_bases.clock_base[CLOCK_MONOTONIC])
Commit e06383db9 (hrtimers: extend hrtimer base code to handle more
then 2 clockids) added an indirection to the hrtimer_bases.clock_base
lookup to avoid gap handling in the hot path. The table which is used
for the translataion from CLOCK_ID to HRTIMER_BASE index is
initialized at runtime in hrtimers_init(). So the early call of the
scheduler code translates CLOCK_MONOTONIC to HRTIMER_BASE_REALTIME.
Thus the rt_bandwith timer ends up on CLOCK_REALTIME. If the timer is
armed and the wall clock time is set (e.g. ntpdate in the early boot
process - which also gives the problem deterministic behaviour
i.e. magic recovery after N hours), then the timer ends up with an
expiry time far into the future. That breaks the RT throttler
mechanism as rt runtime is accumulated and never cleared, so the rt
throttler detects a false cpu hog condition and blocks all RT tasks
until the timer finally expires. That in turn stalls the RCU thread of
TINYRCU which leads to an huge amount of RCU callbacks piling up.
Make the translation table statically initialized, so we are back to
the status of <= 2.6.39.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: John stultz <johnstul@us.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/%3Calpine.LFD.2.02.1104282353140.3005%40ionos%3E
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
pfault, dasd diag and virtio all use the same external interrupt number.
The respective interrupt handlers decide by the subcode if they are
meant to handle the interrupt.
Counting is currently done before looking at the subcode which means
each handler counts an interrupt even if it is not handling it.
Fix this by moving the kstat code after the code which looks at the
subcode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
PC Beep was not being reported as enabled on my EeePC 901:
SKU: enable_pcbeep=0x0
Signed-off-by: Daniel Cordero <danielcordero@lavabit.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Remove coding standard violations reported by checkpatch.pl
- Delete comment about handling of conditional branches which is no
longer true.
- Delete comment at end of file which lists all ARM instructions. This
duplicates data available in the ARM ARM and seems like an
unnecessary maintenance burden to keep this up to date and accurate.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Being able to probe NOP instructions is useful for hard-coding probeable
locations and is used by the kprobes test code.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
These bit field manipulation instructions occur several thousand
times in an ARMv7 kernel.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The MOVW and MOVT instructions account for approximately 7% of all
instructions in a ARMv7 kernel as GCC uses them instead of a literal
pool.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The instruction decoding in space_cccc_000x needs to reject probing of
instructions with undefined patterns as they may in future become
defined and then emulated faultily - as has already happened with the
SMC instruction.
This fix is achieved by testing for the instruction patterns we want to
probe and making the the default fall-through paths reject probes. This
also allows us to remove some explicit tests for instructions that we
wish to reject, as that is now the default action.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The tests to explicitly reject probing CPS, RFE and SRS instructions
are redundant as the default case is now to reject undecoded patterns.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The PLD instructions wasn't being decoded correctly and the emulation
code wasn't adjusting PC correctly.
As the PLD instruction is only a performance hint we emulate it as a
simple nop, and we can broaden the instruction decoding to take into
account newer PLI and PLDW instructions.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The emulation of SETEND was broken as it changed the endianess for
the running kprobes handling code. Rather than adding a new simulation
routine to fix this we'll just reject probing of SETEND as these should
be very rare in the kernel.
Note, the function emulate_none is now unused but it is left in the
source code as future patches will use it.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Following the change to remove support for coprocessor instructions
we are left with three stub functions which can be consolidated.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The kernel doesn't currently support VFP or Neon code, and probing of
code with CP15 operations is fraught with bad consequences. Therefore we
don't need the ability to probe coprocessor instructions and the code to
support this can be removed.
The removed code also had at least two bugs:
- MRC into R15 should set CPSR not trash PC
- LDC and STC which use PC as base register needed the address offset by 8
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The USAD8 instruction wasn't being explicitly decoded leading
to the incorrect emulation routine being called. It can be correctly
decoded in the same way as the signed multiply instructions so we move
the decoding there.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The signed multiply instructions were being decoded incorrectly.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
These sign extension instructions are encoded as extend-and-add
instructions where the register to add is specified as r15. The decoding
routines weren't checking for this and were using the incorrect
emulation code, giving incorrect results.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The instructions space for media instructions contains some undefined
patterns. We need to reject probing of these because they may in future
become defined and the kprobes code may then emulate them faultily.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The v6T2 RBIT instruction was accidentally being emulated correctly,
this patch adds correct decoding for the instruction.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
These instructions are specified as UNPREDICTABLE.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The decoding of these instructions got the register indexed and
immediate indexed forms the wrong way around, causing incorrect
emulation.
Instructions like "LDRD Rx, [Rx]" were corrupting Rx because the base
register writeback was being performed unconditionally, overwriting the
value just loaded from memory. The fix is to only writeback the base
register when that form of the instruction is used. Note, now that we
reject probing writeback with PC the emulation code doesn't need the
check rn!=15.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Using PC as an base register with writeback is UNPREDICTABLE, as is non
word-sized loads or stores of PC. (We only really care about preventing
loads to PC but it keeps the code simpler if we also exclude stores.)
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The decoding of these instructions got the register indexed and
immediate indexed forms the wrong way around, causing incorrect
emulation.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The emulation code for STREX and LDREX instructions is faulty, however,
rather than attempting to fix this we reject probes of these
instructions. We do this because they can never succeed in gaining
exclusive access as the exception framework clears the exclusivity
monitor when a probes breakpoint is hit. (This is a general problem
when probing all instructions executing between a LDREX and its
corresponding STREX and can lead to infinite retry loops.)
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The instructions space for 'Multiply and multiply-accumulate'
instructions contains some undefined patterns. We need to reject
probing of these because they may in future become defined and the
kprobes code may then emulate them faultily.
This has already happened with the new MLS instruction which this patch
also adds correct decoding for as well as tightening up other decoding
tests. (Before this patch the wrong emulation routine was being called
for MLS though it still produced correct results.)
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The MRS instruction should set mode and interrupt bits in the read value
so it is simpler to use a new simulation routine (simulate_mrs) rather
than some modified emulation.
prep_emulate_rd12 is now unused and removed.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
We need to reject probing of instructions which read SPSR because
we can't handle this as the value in SPSR is lost when the exception
handler for the probe breakpoint first runs.
This patch also fixes the bitmask for MRS instructions decoding to
include checking bits 5-7.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Emulation of instructions like "ADD rd, rn, #<const>" would result in a
corrupted value for rd.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Probing these instructions was corrupting R0 because the emulation code
didn't account for the fact that they don't write a result to a
register.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Now we have the framework code handling conditionally executed
instructions we can remove redundant checks in individual simulation
routines.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
When a kprobe is placed onto conditionally executed ARM instructions,
many of the emulation routines used to single step them produce corrupt
register results. Rather than fix all of these cases we modify the
framework which calls them to test the relevant condition flags and, if
the test fails, skip calling the emulation code.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Currently emulate_ldrd and emulate_strd don't even have the adjustment
of the PC value, so in case of Rn == PC, it will not update the PC
incorrectly but instead load/store from the wrong address. Let's add
both the adjustment of the PC value and the check for PC == PC.
Signed-off-by: Viktor Rosendahl <viktor.rosendahl@nokia.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The 88e6085 has a few differences from the other devices in the port
control registers, causing unknown multicast/broadcast packets to get
dropped when using the standard port setup.
At the same time update kconfig to clarify that the mv88e6085 is now
supported.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: restore only the mode of this driver on lastclose (v2)
drm/radeon/kms: add info query for tile pipes
drm/radeon/kms: add missing safe regs for 6xx/7xx
drm: select FRAMEBUFFER_CONSOLE_PRIMARY if we have FRAMEBUFFER_CONSOLE
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
nfs: don't lose MS_SYNCHRONOUS on remount of noac mount
NFS: Return meaningful status from decode_secinfo()
NFSv4: Ensure we request the ordinary fileid when doing readdirplus
NFSv4: Ensure that clientid and session establishment can time out
SUNRPC: Allow RPC calls to return ETIMEDOUT instead of EIO
NFSv4.1: Don't loop forever in nfs4_proc_create_session
NFSv4: Handle NFS4ERR_WRONGSEC outside of nfs4_handle_exception()
NFSv4.1: Don't update sequence number if rpc_task is not sent
NFSv4.1: Ensure state manager thread dies on last umount
SUNRPC: Fix the SUNRPC Kerberos V RPCSEC_GSS module dependencies
NFS: Use correct variable for page bounds checking
NFS: don't negotiate when user specifies sec flavor
NFS: Attempt mount with default sec flavor first
NFS: flav_array honors NFS_MAX_SECFLAVORS
NFS: Fix infinite loop in gss_create_upcall()
Don't mark_inode_dirty_sync() while holding lock
NFS: Get rid of pointless test in nfs_commit_done
NFS: Remove unused argument from nfs_find_best_sec()
NFS: Eliminate duplicate call to nfs_mark_request_dirty
NFS: Remove dead code from nfs_fs_mount()
Resubmit interrupt URB if device is open. Use a flag set in
usbnet_open() to determine this state. Also kill and free
interrupt URB in usbnet_disconnect().
[Rebased off git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git]
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
