The time_format that we stash in the PTP data structure is never
referenced, so we can remove it. Instead, store the information needed
to interpret sync event timestamps.
Also rolls in a couple of other related minor PTP fixes.
Based on patches by Bert Kenward <bkenward@solarflare.com> and Laurence
Evans <levans@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support MC_CMD_PTP_OUT_GET_TIMESTAMP_CORRECTIONS_V2. Extract general
timestamp corrections in addition to PTP corrections. Apply receive
timestamp corrections for general datapath receive timestamping, and
correspondingly for transmit.
Signed-off-by: Laurence Evans <levans@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timestamp conversion function with correction to avoid duplicate
correction handling.
Signed-off-by: Laurence Evans <levans@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We check the license for TX hardware timestamping capability.
The PTP probe will have enabled PTP sync events from the adapter. If
later, at TX queue init, it turns out we do not have the license, we
don't need the sync events either.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For this we create and use one or more new TX queues on the PTP channel,
and enable sync events for it.
Based on a patch by Martin Habets <mhabets@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX timestamps on 8000 series are supplied from the MAC. This timestamp is
only 48 bits long. The high order bits from the last time sync event are
used for the top 16 bits.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we try to enable the feature and do not have the license for it, the
MCPU will refuse and fail our TX queue init.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now transmit SKBs in 2 ways:
1. Via the MC (for the 7XXX series and earlier), using
efx_ptp_xmit_skb_mc().
2. Via the TX queues on the dedicated PTP channel (8XXX series and later),
using efx_ptp_xmit_skb_queue().
The PTP worker thread uses the method set up at probe time. It never
checked the return code from the old efx_ptp_xmit_skb(), so it now
returns void.
We increment the TX dropped counter of the device if the transmit fails.
As a result of the probe per channel the remove gets called multiple times.
Clean up efx->ptp_data properly to avoid the 2nd call blowing up.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use MC capability MC_CMD_GET_CAPABILITIES_V2_OUT_TX_MAC_TIMESTAMPING to
detect whether the NIC supports timestamping packets sent out the main
datapath.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this work, TX timestamping is done by sending each SKB to the MC.
On the 8000 series (Medford1) we have high speed timestamping via the
MAC, which means we can use normal TX queues for this without a
significant drop in bandwidth. On the X2000 series (Medford2) support
for transmitting via the MC is removed, so the new way must be used.
This patch enables timestamping on a TX queue, if requested.
It also enhances TX event handling to process the extra completion events,
and puts the time in the SKB.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NAPI budget is only for RX processing work, not other work such as
TX or MCDI completion handling.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.16. Major changes:
wil6210
* add PCI device id for Talyn
* support flashless device
ath9k
* improve RSSI/signal accuracy on AR9003 series
Add 'static' or declaration to resolve the warnings, and remove two unused
functions halbtc_set_macreg() and halbtc_get_macreg() exposed when they
were made static.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix races and potential use after free in the s390 cmma migration code.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJaaghHAAoJEED/6hsPKofoJksIAJbpIR/Z6n1ycryT6G2iKmda
QT8hYLanuOHNyEinu1AoikqP2bQRzqwuYzfzkECyaliJXKpmki86f8p+HOsNH1Ye
db9vokkvWfyJBZ10d2JOLbGVDxQXX94bMgtO3aF6RcneYgalABOwQU4ltY5gnXXI
5E8xU9d7ya1ivv5ADvPW8tv6GU9YMb5VB1EzM2owjQP3ks0/6p3jXT8XJJGhfufO
6r6Y/E4HnxRKWXTDNoLU6b3sdpCDmMMBRO55AYE2eF/RA84glv9U+xnxs0fXJA8M
OOWrtB4nxxcrCbSve38aONN5E5lSzjWl6/3t2ajbDeIV8r9Fh8Vh7MpeSY6oyZs=
=i5NW
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"Fix races and a potential use after free in the s390 cmma migration
code"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: add proper locking for CMMA migration bitmap
-----BEGIN PGP SIGNATURE-----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=EOAu
-----END PGP SIGNATURE-----
Merge tag 'for-4.15-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"It's been reported recently that readdir can list stale entries under
some conditions. Fix it."
* tag 'for-4.15-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix stale entries in readdir
Currently, we unhash a dying net from netns_ids lists
under rtnl_lock(). It's a leftover from the time when
net::netns_ids was introduced. There was no net::nsid_lock,
and rtnl_lock() was mostly need to order modification
of alive nets nsid idr, i.e. for:
for_each_net(tmp) {
...
id = __peernet2id(tmp, net);
idr_remove(&tmp->netns_ids, id);
...
}
Since we have net::nsid_lock, the modifications are
protected by this local lock, and now we may introduce
better scheme of netns_ids destruction.
Let's look at the functions peernet2id_alloc() and
get_net_ns_by_id(). Previous commits taught these
functions to work well with dying net acquired from
rtnl unlocked lists. And they are the only functions
which can hash a net to netns_ids or obtain from there.
And as easy to check, other netns_ids operating functions
works with id, not with net pointers. So, we do not
need rtnl_lock to synchronize cleanup_net() with all them.
The another property, which is used in the patch,
is that net is unhashed from net_namespace_list
in the only place and by the only process. So,
we avoid excess rcu_read_lock() or rtnl_lock(),
when we'are iterating over the list in unhash_nsid().
All the above makes possible to keep rtnl_lock() locked
only for net->list deletion, and completely avoid it
for netns_ids unhashing and destruction. As these two
doings may take long time (e.g., memory allocation
to send skb), the patch should positively act on
the scalability and signify decrease the time, which
rtnl_lock() is held in cleanup_net().
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a tcp socket is closed, if it detects that its net namespace is
exiting, close immediately and do not wait for FIN sequence.
For normal sockets, a reference is taken to their net namespace, so it will
never exit while the socket is open. However, kernel sockets do not take a
reference to their net namespace, so it may begin exiting while the kernel
socket is still open. In this case if the kernel socket is a tcp socket,
it will stay open trying to complete its close sequence. The sock's dst(s)
hold a reference to their interface, which are all transferred to the
namespace's loopback interface when the real interfaces are taken down.
When the namespace tries to take down its loopback interface, it hangs
waiting for all references to the loopback interface to release, which
results in messages like:
unregister_netdevice: waiting for lo to become free. Usage count = 1
These messages continue until the socket finally times out and closes.
Since the net namespace cleanup holds the net_mutex while calling its
registered pernet callbacks, any new net namespace initialization is
blocked until the current net namespace finishes exiting.
After this change, the tcp socket notices the exiting net namespace, and
closes immediately, releasing its dst(s) and their reference to the
loopback interface, which lets the net namespace continue exiting.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1711407
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=97811
Signed-off-by: Dan Streetman <ddstreet@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware download flow for RAM SKU is same for both USB and UART
and this patch creates a common function for both driver.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
wcn36xx_dxe_init() doesn't check for the return value of
wcn36xx_dxe_init_descs(), release the resources in case an error ocurred.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 series allows to calibrate noise floor for different frequency
bins. Once it's done it's possible to get more accurate rssi/signal
values over whole frequency band at a given temperature.
The RSSI/signal accuracy reported by calibrated RF cards improves
from 6 to up to 2dB.
This could be interesting for application which require good signal
accuracy like roaming or mesh protocols.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 devices can have calibrated noise floor values
which can be used instead of hard coded one. Read them
from eeprom and save interpolated value in nf limits for
the current channel.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 factory calibration allows to use bigger EEPROM than
standard 1k without changing the default layout. Allow
probing of EEPROM at alternative address if initial check
for default fails.
The original ar9003 eeprom ops are still be used.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to allow using the same brd file across different
11ad chips, the address for loading the brd file should be
part of the FW file, instead of the brd file. The brd file is
expected to include only one section.
To allow backward compatibility the driver reads the
address from the brd file in case it is not included in the
FW file.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sparrow D0 chips have slightly larger mac_rgf_ext section
in order to support extra features such as multiple virtual
interfaces.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently when we want to bring the interface up, we first
reset the device which causes the boot loader to run. Then
we halt the device CPU, load FW image and resume the device
CPU.
There are some boot loader versions which perform redundant
memory accesses even when idle. Halting the device CPU
while boot loader access memory can cause the device memory
controller to get stuck, the FW will fail to load and the
network interface will not come up.
For such boot loaders implement a workaround where we freeze
the boot loader before halting the device CPU, so it will not
perform any memory accesses.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
OTP HW vectors values are different for 40MHz and 330MHz AHB
clocks.
In SW reset flow, the host driver sets the clock frequency
to 40MHz. In order to allow reading from the OTP, the host
driver should configure the OTP HW vectors with the values
that fits this clock frequency.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn device supports boot without flash.
Driver detects flashless device and in this case waits for ready indication
from HW machine (instead of bootloader ready indication). Also in this
case, MAC address is retrieved from OTP.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn memory has changed, areas were increased and shifted
to new locations.
Use the appropriate address map according to the device JTAG ID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add Talyn JTAG ID to the list of valid IDs
and identify this device as Talyn.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PCIe device ID has changed in Talyn.
Add this ID to wil6210_pcie_ids list to allow
recognition of Talyn device.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes the hardware will push small packets that trigger a WARN_ON
in mac80211. Discard them early to avoid this issue.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One fixes a NULL dereference, and the other fixes
a flickering bug.
Cc: Eric Anholt <eric@anholt.net>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlpo1gAACgkQlvcN/ahK
Bwp8Dwf/cOHYKoyKmzzMNy4Myrsf0I8cF4efL9f1xw7Y/m/pp7c6Nxdfj0TCmVpd
AmLuxg8rSYrfdnzY5KZ/9nr8RYiWmnX5VIt8VapbZyWF20UUyqilPepHsBrI8lig
rczaOJ8kWL7FDHqXM0CXHQc6mhd7lqKXNfaAwUE3cE9yAve/4tTytrRBXzuhmMmH
AQYsf0Y7v4rv+4SJEZM4UA2n8+TV4WaY1nqjED37lIdApqntL9hR8056lpevWT3W
GgrakE8mZVFTu5KGIBCvZy3yehO/KJ0RIKvPwXJC9e8SMEcP35NuLw0+CetcNTrL
MYure0STUMH0VR9wGLKOh2+bn1106g==
=NPug
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-01-24' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Two vc4 fixes that were applied in the last day.
One fixes a NULL dereference, and the other fixes
a flickering bug.
Cc: Eric Anholt <eric@anholt.net>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
* tag 'drm-misc-fixes-2018-01-24' of git://anongit.freedesktop.org/drm/drm-misc:
drm/vc4: Fix NULL pointer dereference in vc4_save_hang_state()
drm/vc4: Flush the caches before the bin jobs, as well.
Pull networking fixes from David Miller:
1) Avoid negative netdev refcount in error flow of xfrm state add, from
Aviad Yehezkel.
2) Fix tcpdump decoding of IPSEC decap'd frames by filling in the
ethernet header protocol field in xfrm{4,6}_mode_tunnel_input().
From Yossi Kuperman.
3) Fix a syzbot triggered skb_under_panic in pppoe having to do with
failing to allocate an appropriate amount of headroom. From
Guillaume Nault.
4) Fix memory leak in vmxnet3 driver, from Neil Horman.
5) Cure out-of-bounds packet memory access in em_nbyte EMATCH module,
from Wolfgang Bumiller.
6) Restrict what kinds of sockets can be bound to the KCM multiplexer
and also disallow when another layer has attached to the socket and
made use of sk_user_data. From Tom Herbert.
7) Fix use before init of IOTLB in vhost code, from Jason Wang.
8) Correct STACR register write bit definition in IBM emac driver, from
Ivan Mikhaylov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net/ibm/emac: wrong bit is used for STA control register write
net/ibm/emac: add 8192 rx/tx fifo size
vhost: do not try to access device IOTLB when not initialized
vhost: use mutex_lock_nested() in vhost_dev_lock_vqs()
i40e: flower: check if TC offload is enabled on a netdev
qed: Free reserved MR tid
qed: Remove reserveration of dpi for kernel
kcm: Check if sk_user_data already set in kcm_attach
kcm: Only allow TCP sockets to be attached to a KCM mux
net: sched: fix TCF_LAYER_LINK case in tcf_get_base_ptr
net: sched: em_nbyte: don't add the data offset twice
mlxsw: spectrum_router: Don't log an error on missing neighbor
vmxnet3: repair memory leak
ipv6: Fix getsockopt() for sockets with default IPV6_AUTOFLOWLABEL
pppoe: take ->needed_headroom of lower device into account on xmit
xfrm: fix boolean assignment in xfrm_get_type_offload
xfrm: Fix eth_hdr(skb)->h_proto to reflect inner IP version
xfrm: fix error flow in case of add state fails
xfrm: Add SA to hardware at the end of xfrm_state_construct()
Same story as with dev_ifsioc(), except that the last cases with non-trivial
conversions had been taken out in 2013...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Once upon a time net/socket.c:dev_ifsioc() used to handle SIOCSHWTSTAMP and
SIOCSIFMAP. These have different native and compat layout, so the format
conversion had been needed. In 2009 these two cases had been taken out,
turning the rest into a convoluted way to calling sock_do_ioctl(). We copy
compat structure into native one, call sock_do_ioctl() on that and copy
the result back for the in/out ioctls. No layout transformation anywhere,
so we might as well just call sock_do_ioctl() and skip all the headache with
copying.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Only two of dev_ioctl() callers may pass SIOCGIFCONF to it.
Separating that codepath from the rest of dev_ioctl() allows both
to simplify dev_ioctl() itself (all other cases work with struct ifreq *)
*and* seriously simplify the compat side of that beast: all it takes
is passing to inet_gifconf() an extra argument - the size of individual
records (sizeof(struct ifreq) or sizeof(struct compat_ifreq)). With
dev_ifconf() called directly from sock_do_ioctl()/compat_dev_ifconf()
that's easy to arrange.
As the result, compat side of SIOCGIFCONF doesn't need any
allocations, copy_in_user() back and forth, etc.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
STA control register has areas of mode and opcodes for opeations. 18 bit is
using for mode selection, where 0 is old MIO/MDIO access method and 1 is
indirect access mode. 19-20 bits are using for setting up read/write
operation(STA opcodes). In current state 'read' is set into old MIO/MDIO mode
with 19 bit and write operation is set into 18 bit which is mode selection,
not a write operation. To correlate write with read we set it into 20 bit.
All those bit operations are MSB 0 based.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
emac4syn chips has availability to use 8192 rx/tx fifo buffer sizes,
in current state if we set it up in dts 8192 as example, we will get
only 2048 which may impact on network speed.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-01-24
This series contains updates to fm10k only.
Alex fixes MACVLAN offload for fm10k, where we were not seeing unicast
packets being received because we did not correctly configure the
default VLAN ID for the port and defaulting to 0.
Jake cleans up unnecessary parenthesis in a couple of "if" statements.
Fixed the driver to stop adding VLAN 0 into the VLAN table, since it
would cause the VLAN table to be inconsistent between the PF and VF.
Also fixed an issue where we were assuming that VLAN 1 is enabled when
the default VLAN ID is not set, so resolve by not requesting any filters
for the default_vid if it has not yet been assigned.
Ngai fixes an issue which was generating a dmesg regarding unbale to
kill a particular VLAN ID for the device. This is due to
ndo_vlan_rx_kill_vid() exits with an error and the handler for this ndo
is fm10k_update_vid() which exits prematurely under PF VLAN management.
So to resolve, we must check the VLAN update action type before exiting
fm10k_update_vid(), and act appropriately based on the action type.
Also corrected code comment typos.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
