This patch replaces the previous one proposed in the thread "xc3028:
force reload of DTV7 firmware in VHF band with Zarlink demodulator",
at the linux-media@vger.kernel.org ML.
The problem is that the firmware DTV78 works fine in UHF band (8 MHz
bandwidth) but is not working at all in VHF band (7 MHz bandwidth).
Reading the comments inside the code, I figured out that the real
problem could be connected to the formula used to calculate the center
frequency offset in VHF band.
In fact, removing this adjustment fixes the problem:
if ((priv->cur_fw.type & DTV78) && freq < 470000000)
offset -= 500000;
This is coherent to what was implemented for the DTV7 firmware by an
Australian user:
if (priv->cur_fw.type & DTV7)
offset += 500000;
In the end, now the center frequency is the same for all firmwares
(DTV7, DTV8, DTV78) and doesn't depend on channel bandwidth.
The final code looks clean and simple, and there is no need for any
"magic" adjustment:
if (priv->cur_fw.type & DTV6)
offset = 1750000;
else /* DTV7 or DTV8 or DTV78 */
offset = 2750000;
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a big patch, yet trivial: now that all tuners use the DVBv5
way to pass parameters (e. g. via fe->dtv_property_cache), the
extra parameter can be removed from set_params() call.
After this change, very few DVBv3 specific stuff are left at the
tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In radio mode, no frequency offset should be used.
Instead of taking Thierry's patch that creates a separate function
to calculate the digital offset, it seemed better to just keep
everything at the same place.
Reported-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When loading the firmware, complete each chunk by sending an I2C flush
command to the frontend. Some devices like the tm6000 seem to require
this to properly flush the I2C buffers.
The current code in tm6000 executes the flush command once after each
I2C transfer, which slows down the firmware loading especially when
loading large BASE type images.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/common/tuners/tuner-xc2028.c: In function 'generic_set_freq':
drivers/media/common/tuners/tuner-xc2028.c:936:15: warning: comparison between 'enum tuner_mode' and 'enum v4l2_tuner_type'
Argument type was enum tuner_mode, but should have been enum v4l2_tuner_type.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My Hauppauge WinTV HVR-1400 needs sometimes more then only one retry to load the firmware successfully.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a regression in the firmware loading time where it went from 1080 ms to
4700 ms. This was noticed when the em28xx based HVR-950 took noticably longer
to load the driver.
Regression introduced in hg 12824. The developer added an msleep() call with
an argument based on a newly introduced xc3028_ctrl field, which is left
initialized to zero for pretty much every board that is currently supported.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tm6000 sometimes can't read from i2c, but this is currently required for
tuner-xc2028 to work.
This patch adds an option to tuner-xc2028 to not rely on i2c reading.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
A small mistake on the last patch broke demod s-code setup for
XC3028L (firmware 3.2 and upper). Fix it.
Thanks-to: Stefan Ringel <stefan.ringel@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's one reported regression in Australia (DTV7) and some
reported troubles with newer firmwares found on xc3028l chips.
Rework the logic to improve tuner on those cases.
Thanks-to: Robert Lowery <rglowery@exemail.com.au>
Thanks-to: Stefan Ringel <stefan.ringel@arcor.de>
Tested-by: Robert Lowery <rglowery@exemail.com.au>
CC: stable.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A user discovered that the Geniatech x8000 encountered a regression when
the xc3028 power management was introduced. The xc3028 never recovers after
setting the powerdown register, which is probably because the xc3028 reset
GPIO is not properly configured. Since I do not have access to the hardware
and thus cannot determine the correct GPIO configuration, just disable xc3028
power management on this board, which fixes the regression.
Thanks to user "ritec" for reporting the issue and testing the fix.
Cc: rictec <rictec@netcabo.pt>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch should fix 7 MHz DVB-T with the XC3028 using the
DTV7 firmware from the xc3028-v27.fw firmware image.
Tested-by: Terry Wu <terrywu2009@gmail.com>
[mchehab@redhat.com: thanks to John Ferlito, we have a real test in Australia]
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both ATSC and DVB @ 6MHz bandwidth require the same offset.
While we're fixing it, let's cleanup the bandwidth setup to better
reflect the fact that it is a function of the bandwidth.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing this issue and
to Andy Walls <awalls@radix.net> for an initial patch for this fix.
Cc: Terry Wu <terrywu2009@gmail.com>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only two countries that are known to use 6MHz bandwidth are Taiwan
and Uruguay. Both use QAM subcarriers at OFTM.
This patch fixes the firmware load for such countries, where the
required firmware is the QAM one.
This also confirms the previous tests where it was noticed that the 6MHz
QAM firmware doesn't work for cable. So, this patch also removes support
for DVB-C, instead of just printing a warning.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing this issue and
to Andy Walls <awalls@radix.net> for an initial patch for this fix.
Cc: Terry Wu <terrywu2009@gmail.com>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a typo in the module description for the "no_poweroff" option, where the
help was being associated with the "debug" option instead.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the physical device rather than the i2c adapter as the reference
device when loading firmwares. This will prevent the sysfs name
collision with i2c-dev that has been reported many times.
I may have missed other drivers which need the same fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We're going to remove the FIRMWARE_NAME_MAX definition in order to avoid any
firmware name length restriction.
This patch gets rid of the xc2028 FIRMWARE_NAME_MAX reference.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Michel Ludwig <michel.ludwig@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tuner-xc3028 can be put to sleep to save power. However, if not properly
recovered from sleep, the device won't work. It is noticed that some
devices doesn't recover properly, so let's add a dump_stack() as a debug
option, to allow us to track when this happens.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c: In function 'xc2028_sleep':
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c:1111: warning: 'return' with no value, in function returning non-void
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the firmware load is now fast on most boards, better to keep the tuner
off by default. A modprobe parameter were added to keep the old behavior,
to be used by old devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Firmware selection is very tricky on this device. This patch do a better
selection of the proper firmware type, by using a code to hint if the
firmware to be loaded should be D2620 or D2633.
It also allows overriding the hint at the control structure.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use a standard method to manage multiple instances of a hybrid tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were several issues in the past, caused by the hybrid tuner design, since
now, the same tuner can be used by drivers/media/dvb and drivers/media/video.
Kconfig items were rearranged, to split V4L/DVB core from their drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
