While testing an ADC121S021 in an embedded board with a S3C2142 SoC (ARM
core), I have found that the 'adcxx' driver does not handle correctly
single channel ADCs from this chip family. For single channel chips you
must only issue one read transfer for correct measurement.
Signed-off-by: Jose Miguel Goncalves <jose.goncalves@inov.pt>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
String constants that are continued on subsequent lines with \ will cause
spurious whitespace in the resulting output.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This card reader doesn't advertise, however DMA works well. Probably
windows SDHCI driver assumes that all readers support DMA and thus we see
that bug.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Norbert Preining <preining@logic.at>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kunmap_atomic() accepts a pointer to any location in the page so we do not
need the subtraction and cast.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We used to manage features and differences on a per-cpu basis. As several
cpus share the same mci revision, this patch aggregates cpus that have the
same IP revision in one defined constant. We use the
at91mci_is_mci1rev2xx() funtion name not to mess with newer Atmel sd/mmc
IP called "MCI2". _rev2 naming could have been confusing...
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the datasheets AT91SAM9261 does not support SDIO interrupts,
and AT91SAM9260/9263 have an erratum requiring 4bit mode while using slot
B for the interrupt to work.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is setting some max_ variables for the IO elevator, so the
elevator will put requests for large data blocks to the driver. This is
critical for
a) speed
and
b) wear leveling of the flash chip controller: Otherwise the controller
will treat the SD card badly with millions of single 4 KByte write
commands. This will lead to a shorter life time for the SD cards.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the read to use the DMA buffer as well. The old code was doing
double-buffering DMA with the PDC; no way to make it work. Replace it
with a single-PDC approach. It also simplify things removing the need for
a pre_dma_read() function.
[nicolas.ferre@atmel.com coding style modifications]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TX DMA buffer is allocated only once, because the
allocation/deallocation of the buffer for EACH chunk of data is
time-consuming and prone to memory fragmentation.
Using a coherent DMA buffer avoids extra data cache calls.
[nicolas.ferre@atmel.com: coding style modifications]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two timeout errors, one for slow SDHC cards and one for slow users
while inserting SD cards.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes two pointer errors, one which leads to memory overwrites if used
with large chunks of data.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If no platform_data was givin to the device it's going to use it's default
platform data struct which has all fields initialized to zero. As a
result the driver is going to try to request gpio0 both as write protect
and card detect pin. Which of course will fail and makes the driver
unusable
Previously to the introduction of no_wprotect and no_detect the behavior
was to assume that if no platform data was given there is no write protect
or card detect pin. This patch restores that behavior.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
And bring them back to 4-bit mode during resume.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDIO cards may suspend while keeping function interrupts active
especially in the powered suspend case. Upon resume we need to kick the
SDIO interrupt thread to check for pending interrupts and to restart card
IRQ detection at the host controller level.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seen on a Marvell 8686 SDIO card and Via VX855 controller: we must avoid
sending CMD3/5/7 on a resume where power has been maintained, because the
8686 will refuse to respond to them and the MMC stack will give up on the
card.
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested with an XO v1.5 from OLPC.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series provides the core changes needed to allow SDIO cards to
remain powered and active while the host system is suspended, and let them
wake up the host system when needed. This is used to implement
wake-on-lan with SDIO wireless cards at the moment. Patches to add that
support to the libertas driver will be posted separately.
This patch:
Some SDIO cards have the ability to keep on running autonomously when the
host system is suspended, and wake it up when needed. This however
requires that the host controller preserve power to the card, and
configure itself appropriately for wake-up.
There is however 4 layers of abstractions involved: the host controller
driver, the MMC core code, the SDIO card management code, and the actual
SDIO function driver. To make things simple and manageable, host drivers
must advertise their PM capabilities with a feature bitmask, then function
drivers can query and set those features from their suspend method. Then
each layer in the suspend call chain is expected to act upon those bits
accordingly.
[akpm@linux-foundation.org: fix typo in comment]
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sdhci_set_adma_desc() is using byte-writes to write data in a specified
order into memory. Change to using __le16 for the two byte and __le32 for
the four byte cases and use the cpu_to_{le16,le32} to do the conversion
before writing.
This will reduce the size of the code and the number of writes as we no
longer need to chop the data up before writing.
As an example on ARM S3C64XX SoC, in little-endian configuration:
000000d4 <sdhci_set_adma_desc>:
- d8: e1a0c423 lsr ip, r3, #8
- dc: e1a0ec21 lsr lr, r1, #24
- e0: e1a04821 lsr r4, r1, #16
- e4: e1a05421 lsr r5, r1, #8
- e8: e1a06442 asr r6, r2, #8
- ec: e5c0c001 strb ip, [r0, #1]
- f0: e5c0e007 strb lr, [r0, #7]
- f4: e5c04006 strb r4, [r0, #6]
- f8: e5c05005 strb r5, [r0, #5]
- fc: e5c01004 strb r1, [r0, #4]
- 100: e5c06003 strb r6, [r0, #3]
- 104: e5c02002 strb r2, [r0, #2]
- 108: e5c03000 strb r3, [r0]
+ d4: e5801004 str r1, [r0, #4]
+ d8: e1c030b0 strh r3, [r0]
+ dc: e1c020b2 strh r2, [r0, #2]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code to write the ADMA descriptor into memory is repeated several
times throughout sdhci_adma_table_pre, and thus should be moved into a
common function. This will also be useful if the patch to make the write
more efficient is accepted.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDIO cards expect byte transfers not to exceed the configured block
transfer size. Add a quirk to that effect.
Patches to make use of this quirk will be sent separately.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hardcoded value doesn't really work for all cards.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The host/Kconfig file is only included when MMC is selected.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The local sg variable is only used with BF54x code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This prevents those without an Atmel chip having a line in kernel
configuration which says "Atmel SD/MMC Driver" without any option.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for 8bit MMC cards. The controller data width is configurable
depending on the wires setting in the platform data structure.
MMC 8bit is tested on OMAPL137 and MMC 4bit is tested on OMAPL138 EVM.
Signed-off-by: Vipin Bhandari <vipin.bhandari@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch solves nasty problem original driver has.
Original goal of the ricoh_mmc was to disable this device because then,
mmc cards can be read using standard SDHCI controller, thus avoiding
writing of yet another driver.
However, the act of disablement, makes other pci functions that belong to
this controller (xD and memstick) shift up one level, thus pci core has
now wrong idea about these devices.
To fix this issue, this patch moves the driver into the pci quirk section,
thus it is executes before the pci is enumerated, and therefore solving
that issue, also same sequence of commands is performed on resume for same
reasons.
Also regardless of the above, this way is cleaner. You still need to set
CONFIG_MMC_RICOH_MMC to enable this quirk
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Philip Langdale <philipl@overt.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Build list_sort() only for configs that need it -- those that don't save
~581 bytes (i386).
Signed-off-by: Don Mullis <don.mullis@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add adds a debugfs interface and additional failure modes to LKDTM to
provide similar functionality to the provoke-crash driver submitted here:
http://lwn.net/Articles/371208/
Crashes can now be induced either through module parameters (as before)
or through the debugfs interface as in provoke-crash.
The patch also provides a new "direct" interface, where KPROBES are not
used, i.e., the crash is invoked directly upon write to the debugfs
file. When built without KPROBES configured, only this mode is available.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Cc: M. Mohan Kumar <mohan@in.ibm.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The variable priv is initialized twice to the same (side effect-free)
expression. Drop one initialization.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@forall@
idexpression *x;
identifier f!=ERR_PTR;
@@
x = f(...)
... when != x
(
x = f(...,<+...x...+>,...)
|
* x = f(...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the CS5535 MFGPT hrtimer kconfig option to be with the other MFGPT
options. This makes it easier to find and also removes it from the main
"Device Drivers" menu, where it should not have been.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorder struct menu_device to remove 8 bytes of padding on 64 bit builds.
Size drops from 136 to 128 bytes, so possibly needing one fewer cache
lines.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A memmap is a directory in sysfs which includes 3 text files: start, end
and type. For example:
start: 0x100000
end: 0x7e7b1cff
type: System RAM
Interface firmware_map_add was not called explicitly. Remove it and add
function firmware_map_add_hotplug as hotplug interface of memmap.
Each memory entry has a memmap in sysfs, When we hot-add new memory, sysfs
does not export memmap entry for it. We add a call in function add_memory
to function firmware_map_add_hotplug.
Add a new function add_sysfs_fw_map_entry() to create memmap entry, it
will be called when initialize memmap and hot-add memory.
[akpm@linux-foundation.org: un-kernedoc a no longer kerneldoc comment]
Signed-off-by: Shaohui Zheng <shaohui.zheng@intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename for_each_bit to for_each_set_bit in the kernel source tree. To
permit for_each_clear_bit(), should that ever be added.
The patch includes a macro to map the old for_each_bit() onto the new
for_each_set_bit(). This is a (very) temporary thing to ease the migration.
[akpm@linux-foundation.org: add temporary for_each_bit()]
Suggested-by: Alexey Dobriyan <adobriyan@gmail.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use of get_irq_chip_data() et al. requires including linux/irq.h
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: (33 commits)
quota: stop using QUOTA_OK / NO_QUOTA
dquot: cleanup dquot initialize routine
dquot: move dquot initialization responsibility into the filesystem
dquot: cleanup dquot drop routine
dquot: move dquot drop responsibility into the filesystem
dquot: cleanup dquot transfer routine
dquot: move dquot transfer responsibility into the filesystem
dquot: cleanup inode allocation / freeing routines
dquot: cleanup space allocation / freeing routines
ext3: add writepage sanity checks
ext3: Truncate allocated blocks if direct IO write fails to update i_size
quota: Properly invalidate caches even for filesystems with blocksize < pagesize
quota: generalize quota transfer interface
quota: sb_quota state flags cleanup
jbd: Delay discarding buffers in journal_unmap_buffer
ext3: quota_write cross block boundary behaviour
quota: drop permission checks from xfs_fs_set_xstate/xfs_fs_set_xquota
quota: split out compat_sys_quotactl support from quota.c
quota: split out netlink notification support from quota.c
quota: remove invalid optimization from quota_sync_all
...
Fixed trivial conflicts in fs/namei.c and fs/ufs/inode.c
Get rid of the transfer dquot operation - it is now always called from
the filesystem and if a filesystem really needs it's own (which none
currently does) it can just call into it's own routine directly.
Rename the now static low-level dquot_transfer helper to __dquot_transfer
and vfs_dq_transfer to dquot_transfer to have a consistent namespace,
and make the new dquot_transfer return a normal negative errno value
which all callers expect.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6: (49 commits)
drivers/ide: Fix continuation line formats
ide: fixed section mismatch warning in cmd640.c
ide: ide_timing_compute() fixup
ide: make ide_get_best_pio_mode() static
via82cxxx: use ->pio_mode value to determine pair device speed
tx493xide: use ->pio_mode value to determine pair device speed
siimage: use ->pio_mode value to determine pair device speed
palm_bk3710: use ->pio_mode value to determine pair device speed
it821x: use ->pio_mode value to determine pair device speed
cs5536: use ->pio_mode value to determine pair device speed
cs5535: use ->pio_mode value to determine pair device speed
cmd64x: fix handling of address setup timings
amd74xx: use ->pio_mode value to determine pair device speed
alim15x3: fix handling of UDMA enable bit
alim15x3: fix handling of DMA timings
alim15x3: fix handling of command timings
alim15x3: fix handling of address setup timings
ide-timings: use ->pio_mode value to determine fastest PIO speed
ide: change ->set_dma_mode method parameters
ide: change ->set_pio_mode method parameters
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
init: Open /dev/console from rootfs
mqueue: fix typo "failues" -> "failures"
mqueue: only set error codes if they are really necessary
mqueue: simplify do_open() error handling
mqueue: apply mathematics distributivity on mq_bytes calculation
mqueue: remove unneeded info->messages initialization
mqueue: fix mq_open() file descriptor leak on user-space processes
fix race in d_splice_alias()
set S_DEAD on unlink() and non-directory rename() victims
vfs: add NOFOLLOW flag to umount(2)
get rid of ->mnt_parent in tomoyo/realpath
hppfs can use existing proc_mnt, no need for do_kern_mount() in there
Mirror MS_KERNMOUNT in ->mnt_flags
get rid of useless vfsmount_lock use in put_mnt_ns()
Take vfsmount_lock to fs/internal.h
get rid of insanity with namespace roots in tomoyo
take check for new events in namespace (guts of mounts_poll()) to namespace.c
Don't mess with generic_permission() under ->d_lock in hpfs
sanitize const/signedness for udf
nilfs: sanitize const/signedness in dealing with ->d_name.name
...
Fix up fairly trivial (famous last words...) conflicts in
drivers/infiniband/core/uverbs_main.c and security/tomoyo/realpath.c
* git://git.infradead.org/battery-2.6:
power_supply: bq27x00: fix voltage and current units
power_supply: bq27x00: add status and time properties
power_supply: bq27x00: add BQ27500 support
power_supply: bq27x00: fix temperature conversion
power_supply: bq27x00: remove unused struct fields
power_supply: bq27x00: remove double endian swap
da9030_battery: fix spelling in comment
wm97xx_battery: Clean up some warnings
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (27 commits)
Regulators: wm8400 - cleanup platform driver data handling
Regulators: wm8994 - clean up driver data after removal
Regulators: wm831x-xxx - clean up driver data after removal
Regulators: pcap-regulator - clean up driver data after removal
Regulators: max8660 - annotate probe and remove methods
Regulators: max1586 - annotate probe and remove methods
Regulators: lp3971 - fail if platform data was not supplied
Regulators: tps6507x-regulator - mark probe method as __devinit
Regulators: tps65023-regulator - mark probe method as __devinit
Regulators: twl-regulator - mark probe function as __devinit
Regulators: fixed - annotate probe and remove methods
Regulators: ab3100 - fix probe and remove annotations
Regulators: virtual - use sysfs attribute groups
twl6030: regulator: Configure STATE register instead of REMAP
regulator: Provide optional dummy regulator for consumers
regulator: Assume regulators are enabled if they don't report anything
regulator: Convert fixed voltage regulator to use enable_time()
regulator: Add WM8994 regulator support
regulator: enable max8649 regulator driver
regulator: trivial: fix typos in user-visible Kconfig text
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (151 commits)
vga_switcheroo: disable default y by new rules.
drm/nouveau: fix *staging* driver build with switcheroo off.
drm/radeon: fix typo in Makefile
vga_switcheroo: fix build on platforms with no ACPI
drm/radeon: Fix printf type warning in 64bit system.
drm/radeon/kms: bump the KMS version number for square tiling support.
vga_switcheroo: initial implementation (v15)
drm/radeon/kms: do not disable audio engine twice
Revert "drm/radeon/kms: disable HDMI audio for now on rv710/rv730"
drm/radeon/kms: do not preset audio stuff and start timer when not using audio
drm/radeon: r100/r200 ums: block ability for userspace app to trash 0 page and beyond
drm/ttm: fix function prototype to match implementation
drm/radeon: use ALIGN instead of open coding it
drm/radeon/kms: initialize set_surface_reg reg for rs600 asic
drm/i915: Use a dmi quirk to skip a broken SDVO TV output.
drm/i915: enable/disable LVDS port at DPMS time
drm/i915: check for multiple write domains in pin_and_relocate
drm/i915: clean-up i915_gem_flush_gpu_write_domain
drm/i915: reuse i915_gpu_idle helper
drm/i915: ensure lru ordering of fence_list
...
Fixed trivial conflicts in drivers/gpu/vga/Kconfig
If the calling convention of ->timer_fn() and ->cleanup_fn() are unified
across hardware versions we can drop parameters to ioat_init_channel() and
unify ioat_is_dma_complete() implementations.
Both ->timer_fn() and ->cleanup_fn() are modified to expect a struct
dma_chan pointer.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The hardware automatically disables further interrupts after each event
until rearmed. This allows a delay to be injected between the occurence
of the interrupt and the running of the cleanup routine. The delay is
scaled by the descriptor backlog and then written to the INTRDELAY
register which specifies the number of microseconds to hold off
interrupt delivery after an interrupt event occurs. According to
powertop this reduces the interrupt rate from ~5000 intr/s to ~150
intr/s per without affecting throughput (simple dd to a raid6 array).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Since ioat_cleanup_preamble() and the update of the last completed
descriptor are not synchronized there is a chance that two cleanup threads
can see descriptors to clean. If the first cleans up all pending
descriptors then the second will trigger the BUG_ON.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
