Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
In function lowpan_header_create(), we invoke the following code
construct:
struct ipv6hdr *hdr;
...
hdr = ipv6_hdr(skb);
...
if (...)
memcpy(hc06_ptr + 1, &hdr->flow_lbl[1], 2);
else
memcpy(hc06_ptr, &hdr, 4);
Where the else path of the condition, that is, non-compression
path, calls memcpy() with a pointer to struct ipv6hdr *hdr as
source, thus two levels of indirection. This cannot be correct,
and likely only one level of pointer was intended as source
buffer for memcpy() here.
Fixes: 44331fe2aa ("IEEE802.15.4: 6LoWPAN basic support")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.
This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.
At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by David Miller, make genl_register_family_with_ops()
a macro and pass only the array, evaluating ARRAY_SIZE() in the
macro, this is a little safer.
The openvswitch has some indirection, assing ops/n_ops directly in
that code. This might ultimately just assign the pointers in the
family initializations, saving the struct genl_family_and_ops and
code (once mcast groups are handled differently.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only update *addr_len when we actually fill in sockaddr, otherwise we
can return uninitialized memory from the stack to the caller in the
recvfrom, recvmmsg and recvmsg syscalls. Drop the the (addr_len == NULL)
checks because we only get called with a valid addr_len pointer either
from sock_common_recvmsg or inet_recvmsg.
If a blocking read waits on a socket which is concurrently shut down we
now return zero and set msg_msgnamelen to 0.
Reported-by: mpb <mpb.mail@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If priority/traffic class field in IPv6 header is set (seen when
using ssh), the uncompression sets the TC and Flow fields incorrectly.
Example:
This is IPv6 header of a sent packet. Note the priority/TC (=1) in
the first byte.
00000000: 61 00 00 00 00 2c 06 40 fe 80 00 00 00 00 00 00
00000010: 02 02 72 ff fe c6 42 10 fe 80 00 00 00 00 00 00
00000020: 02 1e ab ff fe 4c 52 57
This gets compressed like this in the sending side
00000000: 72 31 04 06 02 1e ab ff fe 4c 52 57 ec c2 00 16
00000010: aa 2d fe 92 86 4e be c6 ....
In the receiving end, the packet gets uncompressed to this
IPv6 header
00000000: 60 06 06 02 00 2a 1e 40 fe 80 00 00 00 00 00 00
00000010: 02 02 72 ff fe c6 42 10 fe 80 00 00 00 00 00 00
00000020: ab ff fe 4c 52 57 ec c2
First four bytes are set incorrectly and we have also lost
two bytes from destination address.
The fix is to switch the case values in switch statement
when checking the TC field.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genl_ops are no longer modified in place when
registering, they can be made const. This patch was done
mostly with spatch:
@@
identifier ops;
@@
+const
struct genl_ops ops[] = {
...
};
(except the struct thing in net/openvswitch/datapath.c)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the code since there's no longer a need to
have error handling in the registration.
Unfortunately it means more extern function declarations are
needed, but the overall goal would seem to justify this.
While at it, also fix the registration error path - if the
family registration failed then it shouldn't be unregistered.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently added a new error path and it needs a dev_put().
Fixes: 7adac1ec81 ('6lowpan: Only make 6lowpan links to IEEE802154 devices')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch drops the direct memcpy on skb and uses the right skb
memcpy functions. Also remove an unnecessary check if plen is non zero.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary to access network header with the skb_network_header
function instead of calculate the position with mac_len, etc.
Do the same for the transport header, when we replace the IPv6 header
with the 6LoWPAN header.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the mac header length while creating the 802.15.4 mac header.
Drop the function for recalculate mac header length in upper layers
which was static and works for intra pan communication only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On receiving side we don't need to set any headers in skb because the
6LoWPAN layer do not access it. Currently these values will set twice
after calling netif_rx.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the assignment of skb->dev. We don't need it here because
we use the netdev_alloc_skb_ip_align function which already sets the
skb->dev.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses the netdev_alloc_skb instead dev_alloc_skb function and
drops the seperate assignment to skb->dev.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The err variable can only be zero in this case.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a lowpan link to a wpan device is created, set the hardware address
of the lowpan link to that of the wpan device.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refuse to create 6lowpan links if the actual hardware interface is
of any type other than ARPHRD_IEEE802154.
Signed-off-by: Alan Ott <alan@signal11.us>
Suggested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
Handle context based address when an unspecified address is given.
For other context based address we print a warning and drop the packet
because we don't support it right now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch drops the pre and postcount calculation from the
lowpan_uncompress_addr function.We use instead a switch/case
over address_mode value. The original implementation has several
bugs in this function and it was hard to decrypt how it works.
To make it maintainable and fix these bugs this patch basically
reimplements lowpan_uncompress_addr from scratch.
A list of bugs we found in the current implementation:
1) Properly support uncompression of short-address based IPv6 addresses
(instead of basically copying garbage)
2) Fix use and uncompression of long-addresses based IPv6 addresses
3) Add missing ff:fe00 in the case of SAM/DAM = 2 and M = 0
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to uncompress multicast address.
This function split the uncompress function for a multicast address
in a seperate function.
To uncompress a multicast address is different than a other
non-multicasts addresses according to rfc6282.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a helper function to parse the ipv6 header to a
6lowpan header in stream.
This function checks first if we can pull data with a specific
length from a skb. If this seems to be okay, we copy skb data to
a destination pointer and run skb_pull.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new 6lowpan fragment is received, a skbuff is allocated for
the reassembled packet. However when a 6lowpan packet compresses
link-local addresses based on link-layer addresses, the processing
function relies on the skb mac control block to find the related
link-layer address.
This patch copies the control block from the first fragment into
the newly allocated skb to keep a trace of the link-layer addresses
in case of a link-local compressed address.
Edit: small changes on comment issue
Signed-off-by: David Hauweele <david@hauweele.net>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplify the handling to set fields inside of struct ipv6hdr
to zero. Instead of setting some memory regions with memset to zero we
initialize the whole ipv6hdr to zero.
This is a simplification for parsing the 6lowpan header for the upcomming
patches.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the ieee802154 class code to use
the correct field.
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: fix typo on simeth
shortened dev_getter
shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for NULL before calling the following operations from "struct
ieee802154_mlme_ops": assoc_req, assoc_resp, disassoc_req, start_req,
and scan_req.
This fixes a current oops where those functions are called but not
implemented. It also updates the documentation to clarify that they
are now optional by design. If a call to an unimplemented function
is attempted, the kernel returns EOPNOTSUPP via netlink.
The following operations are still required: get_phy, get_pan_id,
get_short_addr, and get_dsn.
Note that the places where this patch changes the initialization
of "ret" should not affect the rest of the code since "ret" was
always set (again) before returning its value.
Signed-off-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_queue_xmit() will return a positive value if the packet could not be
queued, often because the real network device (in our case the mac802154
wpan device) has its queue stopped. lowpan_xmit() should handle the
positive return code (for the debug statement) and return that value to
the higher layer so the higher layer will retry sending the packet.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This formatting issue was introduced with commit
d4ac32365d
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch lets dgram_recvmsg fill in the sockaddr struct in
msg->msg_name with the source address of the packet.
This is used by the userland functions recvmsg and recvfrom to get the
senders address.
[Stefan: Changed from old zigbee legacy tree to mainline]
Signed-off-by: Stephen Röttger <stephen.roettger@zero-entropy.de>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code would just compress the UDP header and send the compressed
UDP header along with the uncompressed one.
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sets the sequence number in the frame format. Without this fix, the sequence
number is always set to 0. This makes trafic analysis very hard.
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pr_debug() call in order to debug 6LoWPAN fragmentation and
reassembly.
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first fragment, FRAG1, must contain some payload according to the
specs. However, as it is currently written, the first fragment will
remain empty and only contain the 6lowpan headers.
This patch also extracts the transport layer information from the first
fragment. This information is used later on when uncompressing UDP
header.
Thanks to Wolf-Bastian Pöttner for noticing that the offset value was
not properly initialized.
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE 802.15.4 standard uses the 0xFFFF short address (2 bytes) for message
broadcasting.
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is especially important when using fragmentation, because
the reassembly mechanism cannot recover from the loss of a fragment.
Note that some hardware ignore this flag and not will not transmit
acknowledgments even if this is set.
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current test is not RFC6282 compliant. The same issue has been found
and fixed in Contiki. This patch is basically a port of their fix.
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
