There are 3 places defining similar functions of saving IRQ vector
info into mp_irqs[] array: mmparse/acpi/mrst.
Replace the redundant code by a common function in io_apic.c as it's
only called when CONFIG_X86_IO_APIC=y
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20101207133204.4d913c5a@feng-i7>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For 32bit mptable path, setup_ids_from_mpc() always writes the io_apic
id register, even there is no change needed.
Skip the write, when readout and mptable match.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
LKML-Reference: <4CFDF785.7010401@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If x2apic is preenabled and used by the kernel, we don't need to map
the lapic address. That mapping will never be used.
So just skip that in register_lapic_address()
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4CFDF69C.9070501@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
register_lapic_address() and mp_sfi_register_lapic_address() are
almost identical. Use the common function.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4CFDF693.6000908@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove the printk as well, we don't want to print when nothing
changed. We print in register_lapic_address() already.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4CFDF68A.7020902@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is almost the same as smp_register_lapic_addr(). We just need to
let smp_read_mpc() call smp_register_lapic_addr() when early==1.
Add the apic_printk to smp_register_lapic_address()
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4CFDF681.3030509@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
They are the same, move the common function to apic.c to allow
further cleanups.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4CFDF675.4060305@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reason: apic cleanup series depends on x86/apic, x86/amd-nb x86/platform
Conflicts:
arch/x86/include/asm/io_apic.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/x86/kernel/apic/io_apic.c: In function 'ack_apic_level':
arch/x86/kernel/apic/io_apic.c:2433: warning: unused variable 'desc'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <201010272107.o9RL7rse018212@imap1.linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/x86/kernel/apic/hw_nmi.c:29: warning: backtrace_mask defined but not used
commit 0e2af2a9(x86, hw_nmi: Move backtrace_mask declaration under
ARCH_HAS_NMI_WATCHDOG) addressed this warning, but it was reintroduced
by commit 5f2b0ba4(x86, nmi_watchdog: Remove the old nmi_watchdog).
Move backtrace_mask into the #ifdef arch_trigger_all_cpu_backtrace
section again.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <AANLkTi=rcc38QzoKa6LFy4m++-p_9=Zt4_kDQE=GeKxf@mail.gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since all the hotplug stuff is serialized by the hotplug mutex,
do away with the amd_nb_lock.
Cc: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the number of CPUID leaves KVM handles is limited to 40.
My desktop machine (AthlonII) already has 35 and future CPUs will
expand this well beyond the limit. Extend the limit to 80 to make
room for future processors.
KVM-Stable-Tag.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
To support xsave properly for the guest the SVM module need
software support for it. As long as this is not present do
not report the xsave as supported feature in cpuid.
As a side-effect this patch moves the bit() helper function
into the x86.h file so that it can be used in svm.c too.
KVM-Stable-Tag.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
CPUID's OSXSAVE is a mirror of CR4.OSXSAVE bit. We need to update the CPUID
after migration.
KVM-Stable-Tag.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/pvclock: Zero last_value on resume
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf record: Fix eternal wait for stillborn child
perf header: Don't assume there's no attr info if no sample ids is provided
perf symbols: Figure out start address of kernel map from kallsyms
perf symbols: Fix kallsyms kernel/module map splitting
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: Fix printk_needs_cpu() return value on offline cpus
printk: Fix wake_up_klogd() vs cpu hotplug
Move the code to arch/x86/platform/mrst/. Also fix a typo to use
the correct config option: ONFIG_EARLY_PRINTK_MRST
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: alan@linux.intel.com
LKML-Reference: <1291348298-21263-1-git-send-email-feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use text_poke_smp_batch() on unoptimization path for reducing
the number of stop_machine() issues. If the number of
unoptimizing probes is more than MAX_OPTIMIZE_PROBES(=256),
kprobes unoptimizes first MAX_OPTIMIZE_PROBES probes and kicks
optimizer for remaining probes.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <20101203095434.2961.22657.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use text_poke_smp_batch() in optimization path for reducing
the number of stop_machine() issues. If the number of optimizing
probes is more than MAX_OPTIMIZE_PROBES(=256), kprobes optimizes
first MAX_OPTIMIZE_PROBES probes and kicks optimizer for
remaining probes.
Changes in v5:
- Use kick_kprobe_optimizer() instead of directly calling
schedule_delayed_work().
- Rescheduling optimizer outside of kprobe mutex lock.
Changes in v2:
- Allocate code buffer and parameters in arch_init_kprobes()
instead of using static arraies.
- Merge previous max optimization limit patch into this patch.
So, this patch introduces upper limit of optimization at
once.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <20101203095428.2961.8994.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce text_poke_smp_batch(). This function modifies several
text areas with one stop_machine() on SMP. Because calling
stop_machine() is heavy task, it is better to aggregate
text_poke requests.
( Note: I've talked with Rusty about this interface, and
he would not like to expand stop_machine() interface, since
it is not for generic use. )
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <20101203095422.2961.51217.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Unoptimization occurs when a probe is unregistered or disabled,
and is heavy because it recovers instructions by using
stop_machine(). This patch delays unoptimization operations and
unoptimize several probes at once by using
text_poke_smp_batch(). This can avoid unexpected system slowdown
coming from stop_machine().
Changes in v5:
- Split this patch into several cleanup patches and this patch.
- Fix some text_mutex lock miss.
- Use bool instead of int for behavior flags.
- Add additional comment for (un)optimizing path.
Changes in v2:
- Use dynamic allocated buffers and params.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <20101203095409.2961.82733.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit a5ef2e70 "x86: Sanitize apb timer interrupt handling" forgot
the affinity setup when cleaning up the code, this patch just
adds the forgotten part
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Jacob Pan <jacob.jun.pan@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
LKML-Reference: <1291348298-21263-2-git-send-email-feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch enables the UART on the CE4100. The UART has a couple of
issues that need to be worked around. First the UART is mostly PC
compatible except that it is clocked eight times faster than a
standard PC so the default configuration provided in
arch/x86/include/asm/serial.h needs to be overridden. Second the TX
interrupt may not be set correctly all the time. Lastly accessing the
UART via I/O space for early_prink() hangs the chip when the IOAPIC is
enabled.
A custom mem_serial_in() is provided to work around the TX interrupt
issue. The configuration issues are dealt with in the call back
registered with the 8250 driver via serial8250_set_isa_configurator()
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
LKML-Reference: <1290436128-17958-1-git-send-email-dirk.brandewie@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Sodaville needs to setup the IO_APIC ids as the boot loader leaves
them uninitialized. Split out the setter function so it can be called
unconditionally from the sodaville board code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20101126165020.GA26361@www.tglx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* '2.6.37-rc4-pvhvm-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: unplug the emulated devices at resume time
xen: fix save/restore for PV on HVM guests with pirq remapping
xen: resume the pv console for hvm guests too
xen: fix MSI setup and teardown for PV on HVM guests
xen: use PHYSDEVOP_get_free_pirq to implement find_unbound_pirq
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: allocate irq descs on any NUMA node
xen: prevent crashes with non-HIGHMEM 32-bit kernels with largeish memory
xen: use default_idle
xen: clean up "extra" memory handling some more
* 'upstream/bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: x86/32: perform initial startup on initial_page_table
xen: don't bother to stop other cpus on shutdown/reboot
Boot to boot the TSC calibration may vary by quite a large amount.
While normal variance of 50-100ppm can easily be seen, the quick
calibration code only requires 500ppm accuracy, which is the limit
of what NTP can correct for.
This can cause problems for systems being used as NTP servers, as
every time they reboot it can take hours for them to calculate the
new drift error caused by the calibration.
The classic trade-off here is calibration accuracy vs slow boot times,
as during the calibration nothing else can run.
This patch uses a delayed workqueue to calibrate the TSC over the
period of a second. This allows very accurate calibration (in my
tests only varying by 1khz or 0.4ppm boot to boot). Additionally this
refined calibration step does not block the boot process, and only
delays the TSC clocksoure registration by a few seconds in early boot.
If the refined calibration strays 1% from the early boot calibration
value, the system will fall back to already calculated early boot
calibration.
Credit to Andi Kleen who suggested using a timer quite awhile back,
but I dismissed it thinking the timer calibration would be done after
the clocksource was registered (which would break things). Forgive
me for my short-sightedness.
This patch has worked very well in my testing, but TSC hardware is
quite varied so it would probably be good to get some extended
testing, possibly pushing inclusion out to 2.6.39.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1289003985-29060-1-git-send-email-johnstul@us.ibm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@elte.hu>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Clark Williams <williams@redhat.com>
CC: Andi Kleen <andi@firstfloor.org>
On stock 2.6.37-rc4, running:
# mount lilith:/export /mnt/lilith
# find /mnt/lilith/ -type f -print0 | xargs -0 file
crashes the machine fairly quickly under Xen. Often it results in oops
messages, but the couple of times I tried just now, it just hung quietly
and made Xen print some rude messages:
(XEN) mm.c:2389:d80 Bad type (saw 7400000000000001 != exp
3000000000000000) for mfn 1d7058 (pfn 18fa7)
(XEN) mm.c:964:d80 Attempt to create linear p.t. with write perms
(XEN) mm.c:2389:d80 Bad type (saw 7400000000000010 != exp
1000000000000000) for mfn 1d2e04 (pfn 1d1fb)
(XEN) mm.c:2965:d80 Error while pinning mfn 1d2e04
Which means the domain tried to map a pagetable page RW, which would
allow it to map arbitrary memory, so Xen stopped it. This is because
vm_unmap_ram() left some pages mapped in the vmalloc area after NFS had
finished with them, and those pages got recycled as pagetable pages
while still having these RW aliases.
Removing those mappings immediately removes the Xen-visible aliases, and
so it has no problem with those pages being reused as pagetable pages.
Deferring the TLB flush doesn't upset Xen because it can flush the TLB
itself as needed to maintain its invariants.
When unmapping a region in the vmalloc space, clear the ptes
immediately. There's no point in deferring this because there's no
amortization benefit.
The TLBs are left dirty, and they are flushed lazily to amortize the
cost of the IPIs.
This specific motivation for this patch is an oops-causing regression
since 2.6.36 when using NFS under Xen, triggered by the NFS client's use
of vm_map_ram() introduced in 56e4ebf877b60 ("NFS: readdir with vmapped
pages") . XFS also uses vm_map_ram() and could cause similar problems.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Bryan Schumaker <bjschuma@netapp.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Alex Elder <aelder@sgi.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When remapping MSIs into pirqs for PV on HVM guests, qemu is responsible
for doing the actual mapping and unmapping.
We only give qemu the desired pirq number when we ask to do the mapping
the first time, after that we should be reading back the pirq number
from qemu every time we want to re-enable the MSI.
This fixes a bug in xen_hvm_setup_msi_irqs that manifests itself when
trying to enable the same MSI for the second time: the old MSI to pirq
mapping is still valid at this point but xen_hvm_setup_msi_irqs would
try to assign a new pirq anyway.
A simple way to reproduce this bug is to assign an MSI capable network
card to a PV on HVM guest, if the user brings down the corresponding
ethernet interface and up again, Linux would fail to enable MSIs on the
device.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Only make swapper_pg_dir readonly and pinned when generic x86 architecture code
(which also starts on initial_page_table) switches to it. This helps ensure
that the generic setup paths work on Xen unmodified. In particular
clone_pgd_range writes directly to the destination pgd entries and is used to
initialise swapper_pg_dir so we need to ensure that it remains writeable until
the last possible moment during bring up.
This is complicated slightly by the need to avoid sharing kernel PMD entries
when running under Xen, therefore the Xen implementation must make a copy of
the kernel PMD (which is otherwise referred to by both intial_page_table and
swapper_pg_dir) before switching to swapper_pg_dir.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Xen will shoot all the VCPUs when we do a shutdown hypercall, so there's
no need to do it manually.
In any case it will fail because all the IPI irqs have been pulled
down by this point, so the cross-CPU calls will simply hang forever.
Until change 76fac077db6b34e2c6383a7b4f3f4f7b7d06d8ce the function calls
were not synchronously waited for, so this wasn't apparent. However after
that change the calls became synchronous leading to a hang on shutdown
on multi-VCPU guests.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Cc: Alok Kataria <akataria@vmware.com>
Exclude AES-GCM code for x86-32 due to heavy usage of 64-bit registers
not available on x86-32.
While at it, fixed unregister order in aesni_exit().
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the guest domain has been suspend/resumed or migrated, then the
system clock backing the pvclock clocksource may revert to a smaller
value (ie, can be non-monotonic across the migration/save-restore).
Make sure we zero last_value in that case so that the domain
continues to see clock updates.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The AES-NI instructions are also available in legacy mode so the 32-bit
architecture may profit from those, too.
To illustrate the performance gain here's a short summary of a dm-crypt
speed test on a Core i7 M620 running at 2.67GHz comparing both assembler
implementations:
x86: i568 aes-ni delta
ECB, 256 bit: 93.8 MB/s 123.3 MB/s +31.4%
CBC, 256 bit: 84.8 MB/s 262.3 MB/s +209.3%
LRW, 256 bit: 108.6 MB/s 222.1 MB/s +104.5%
XTS, 256 bit: 105.0 MB/s 205.5 MB/s +95.7%
Additionally, due to some minor optimizations, the 64-bit version also
got a minor performance gain as seen below:
x86-64: old impl. new impl. delta
ECB, 256 bit: 121.1 MB/s 123.0 MB/s +1.5%
CBC, 256 bit: 285.3 MB/s 290.8 MB/s +1.9%
LRW, 256 bit: 263.7 MB/s 265.3 MB/s +0.6%
XTS, 256 bit: 251.1 MB/s 255.3 MB/s +1.7%
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
dmar, x86: Use function stubs when CONFIG_INTR_REMAP is disabled
x86-64: Fix and clean up AMD Fam10 MMCONF enabling
x86: UV: Address interrupt/IO port operation conflict
x86: Use online node real index in calulate_tbl_offset()
x86, asm: Fix binutils 2.15 build failure
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf symbols: Remove incorrect open-coded container_of()
perf record: Handle restrictive permissions in /proc/{kallsyms,modules}
x86/kprobes: Prevent kprobes to probe on save_args()
irq_work: Drop cmpxchg() result
perf: Fix owner-list vs exit
x86, hw_nmi: Move backtrace_mask declaration under ARCH_HAS_NMI_WATCHDOG
tracing: Fix recursive user stack trace
perf,hw_breakpoint: Initialize hardware api earlier
x86: Ignore trap bits on single step exceptions
tracing: Force arch_local_irq_* notrace for paravirt
tracing: Fix module use of trace_bprintk()
Add description of .config in a sake of RAW events.
At least this should bring some light to those who
will be reading this code.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Reviewed-by: Stephane Eranian <eranian@google.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The perf hardware pmu got initialized at various points in the boot,
some before early_initcall() some after (notably arch_initcall).
The problem is that the NMI lockup detector is ran from early_initcall()
and expects the hardware pmu to be present.
Sanitize this by moving all architecture hardware pmu implementations to
initialize at early_initcall() and move the lockup detector to an explicit
initcall right after that.
Cc: paulus <paulus@samba.org>
Cc: davem <davem@davemloft.net>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1290707759.2145.119.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When booting up a CPU set the various topology masks before
calling the CPU_STARTING notifier. This way the notifier
can actually use the masks.
This is needed for a perf change.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1290077254-12165-2-git-send-email-andi@firstfloor.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
and use it when appropriate.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1290525705-6265-1-git-send-email-fbuihuu@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This leads to a Kconfig dep inversion, x86 selects PERF_EVENT (due to
a hw_breakpoint dep) but doesn't unconditionally provide
HAVE_PERF_EVENT.
(This can cause build failures on M386/M486 kernel .config's.)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20101117222055.982965150@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In a kvm virt guests, the perf counters are not emulated. Instead they
return zero on a rdmsrl. The perf nmi handler uses the fact that crossing
a zero means the counter overflowed (for those counters that do not have
specific interrupt bits). Therefore on kvm guests, perf will swallow all
NMIs thinking the counters overflowed.
This causes problems for subsystems like kgdb which needs NMIs to do its
magic. This problem was discovered by running kgdb tests.
The solution is to write garbage into a perf counter during the
initialization and hopefully reading back the same number. On kvm
guests, the value will be read back as zero and we disable perf as
a result.
Reported-by: Jason Wessel <jason.wessel@windriver.com>
Patch-inspired-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
LKML-Reference: <1290462923-30734-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When compiling arch/x86/kernel/early_printk_mrst.c with i386
allmodconfig, gcc-4.1.0 generates an out-of-line copy of
__set_fixmap_offset() which contains a reference to
__this_fixmap_does_not_exist which the compiler cannot elide.
Marking __set_fixmap_offset() as __always_inline prevents this.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Feng Tang <feng.tang@intel.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
