Currently the mlx4 drivers don't have the necessary callbacks to
implement EEH errors detection and recovery, so the PCI layer uses the
probe and remove callbacks to try to recover the device after an error on
the bus. However, these callbacks have race conditions with the internal
catastrophic error recovery functions, which will also detect the error
and this can cause the system to crash if both EEH and catas functions
try to reset the device.
This patch adds the necessary error recovery callbacks and makes sure
that the internal catastrophic error functions will not try to reset the
device in such scenarios. It also adds some calls to
pci_channel_offline() to suppress reads/writes on the bus when the slot
cannot accept I/O operations so we prevent unnecessary accesses to the
bus and speed up the device removal.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bombing to convert pci_bus.subordinate to busn_res.end accidentally
modified a "struct pci_dev" site, causing this file not to compile.
This commit reverts that code to use dev->subordinate again.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Yinghai Lu removed pci_bus.subordinate in pci-next, which meant that
the tile-next changes to add tilegx PCI support don't build. This
was expected (seen in linux-next) and this one-line fix is along
the same lines as commit b918c62e for all other architectures.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This patch introduces the BTRFS_IOC_SEND ioctl that is
required for send. It allows btrfs-progs to implement
full and incremental sends. Patches for btrfs-progs will
follow.
Signed-off-by: Alexander Block <ablock84@googlemail.com>
Reviewed-by: David Sterba <dave@jikos.cz>
Reviewed-by: Arne Jansen <sensille@gmx.net>
Reviewed-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Reviewed-by: Alex Lyakas <alex.bolshoy.btrfs@gmail.com>
This function is used to find the differences between
two trees. The tree compare skips whole subtrees if it
detects shared tree blocks and thus is pretty fast.
Signed-off-by: Alexander Block <ablock84@googlemail.com>
Reviewed-by: David Sterba <dave@jikos.cz>
Reviewed-by: Arne Jansen <sensille@gmx.net>
Reviewed-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Reviewed-by: Alex Lyakas <alex.bolshoy.btrfs@gmail.com>
This patch introduces uuids for subvolumes. Each
subvolume has it's own uuid. In case it was snapshotted,
it also contains parent_uuid. In case it was received,
it also contains received_uuid.
It also introduces subvolume ctime/otime/stime/rtime. The
first two are comparable to the times found in inodes. otime
is the origin/creation time and ctime is the change time.
stime/rtime are only valid on received subvolumes.
stime is the time of the subvolume when it was
sent. rtime is the time of the subvolume when it was
received.
Additionally to the times, we have a transid for each
time. They are updated at the same place as the times.
btrfs receive uses stransid and rtransid to find out
if a received subvolume changed in the meantime.
If an older kernel mounts a filesystem with the
extented fields, all fields become invalid. The next
mount with a new kernel will detect this and reset the
fields.
Signed-off-by: Alexander Block <ablock84@googlemail.com>
Reviewed-by: David Sterba <dave@jikos.cz>
Reviewed-by: Arne Jansen <sensille@gmx.net>
Reviewed-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Reviewed-by: Alex Lyakas <alex.bolshoy.btrfs@gmail.com>
Each ordered operation has a free callback, and this was called with the
worker spinlock held. Josef made the free callback also call iput,
which we can't do with the spinlock.
This drops the spinlock for the free operation and grabs it again before
moving through the rest of the list. We'll circle back around to this
and find a cleaner way that doesn't bounce the lock around so much.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
cc: stable@kernel.org
In support of the recently added capability to remount with lzo
compression, provide a helper function to check the compression
INCOMPAT flags when remounting with lzo compression, and set
the flags if necessary.
Also, implement the new helper function when defragmenting with
explicit lzo compression and when setting the default subvolume.
Signed-off-by: Mitch Harder <mitch.harder@sabayonlinux.org>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
This was accidentally disabled by commit 2a5fdc9 "ARM: dt: tegra:
invert status=disable vs status=okay".
Cc: <stable@vger.kernel.org> # v3.5 (file is named tegra-trimslice.dts there)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On TrimSlice, Tegra's USB1 port may be routed to either an external micro
USB port, or an internal USB->SATA bridge for SSD or HDD. This muxing is
controlled by a GPIO. Whilst not strictly a VBUS GPIO, the TrimSlice
board files caused this GPIO to be set appropriately to enable the SATA
bridge by passing it as the VBUS GPIO to the USB driver. Echo this same
configuration in device tree to enable the SATA bridge.
An alternative might be to implement a full USB bus mux driver. However,
that seems over-complex right now.
Cc: <stable@vger.kernel.org> # v3.5 (file is named tegra-trimslice.dts there)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a MAINTAINERS entry for mach-vt8500 and related files.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After merging the libata tree, today's [2012-07-01] linux-next build (x86_64
allmodconfig) failed like this:
drivers/ata/libata-acpi.c: In function 'ata_acpi_set_state':
drivers/ata/libata-acpi.c:872:5: error: too few arguments to function 'acpi_pm_device_sleep_state'
include/acpi/acpi_bus.h:418:5: note: declared here
Caused by commit 3bd46600a7a7 ("libata-acpi: add ata port runtime D3Cold
support") from the libata tree interacting with commit ee85f543710d
("ACPI/PM: specify lowest allowed state for device sleep state") from the
pci tree.
This patch adds ACPI_STATE_D3 as the new third parameter to
acpi_pm_device_sleep_state()
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Two bits were appended to the end of the bitfield
list in struct scsi_device. Resolve that conflict
by including both bits.
Conflicts:
include/scsi/scsi_device.h
Only channel 0 is currently support and the driver code is fixed on
channel 0. This patch lets device node specifying dma-channel in case
it is not 0. If no dma-channel property is specified, channel 0 is
used as default.
Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The readpages bug is a regression that was introduced in 6993f74a5.
This also fixes a couple of similar bugs in the uncached read and write
codepaths.
Also, prevent this sort of thing in the future by having cifsFileInfo_get
take the spinlock itself, and adding a _locked variant for use in places
that are already holding the lock. The _put code has always done that
so this makes for a less confusing interface.
Cc: <stable@vger.kernel.org> # 3.5.x
Reviewed-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Fixed coding style issues related to braces found
by checkpatch.pl in drivers/ata/ahci.c
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The function ata_ering_clear_cb is only referenced in this file and
should be marked static to prevent it from being exposed globally.
This quiets the sparse warning:
warning: symbol 'ata_ering_clear_cb' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.
This quiets the sparse warnings:
warning: symbol 'ata_is_port' was not declared. Should it be static?
warning: symbol 'ata_is_link' was not declared. Should it be static?
warning: symbol 'ata_is_ata_dev' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The hardreset operation is currently not supported. This causes
sometime the SATA driver does cause kernel crash because of
none-determined state.a This patch will fix the issue.
Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch converts the drivers in drivers/ata/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Mark Lord <kernel@teksavvy.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
IO_DATA_PATH_WIDTH_8 is 0, so a bit-and with it is always false. The
value IO_DATA_PATH_WIDTH covers the bits of the IO_DATA_PATH constants, so
first pick those bits and then make the test using !=.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With the new i.mx clock framework, we need to use
clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Like e65cc194f7628ecaa02462f22f42fb09b50dcd49 (ahci: Enable SB600 64bit
DMA on MSI K9A2 Platinum) and 3c4aa91f21f65b7b40bdfb015eacbcb8453ccae2
(ahci: Enable SB600 64bit DMA on Asus M3A), this patch enables 64bit DMA
for the AHCI SATA controller of another board that has the SB600
southbridge.
In this case though we're enabling 64bit DMA for another MSI motherboard,
the K9AGM2 or MS-7327. It is new enough that all of the BIOS releases
since the initial release (1.0 from 2007-02-09) work correctly with 64bit
DMA enabled.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure,
interface errors are always seen until 1.5Gbps is negotiated [1]. This
occurs using any disk in the enclosure, and when the disk is connected
directly with a generic passive eSATAp cable, we see stable 3Gbps
operation as expected.
Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset
and renegotiation incurs.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 6b66d95895c149cbc04d4fac5a2f5477c543a8ae should not have changed
EXPORT_SYMBOL_GPL to EXPORT_SYMBOL.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Adds inline for ata_acpi_unregister/ata_acpi_bind/ata_acpi_unbind
in drivers/ata/libata.h for !CONFIG_ATA_ACPI to fix below warnings.
warning: 'ata_acpi_unregister' defined but not used [-Wunused-function]
warning: 'ata_acpi_bind' defined but not used [-Wunused-function]
warning: 'ata_acpi_unbind' defined but not used [-Wunused-function]
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Often no exact match is wanted but just the next lower or
higher item. There's a lot of duplicated code throughout
btrfs to deal with the corner cases. This patch adds a
helper function that can facilitate searching.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Lift the EXDEV condition and allow different root trees for files being
cloned, then pass source inode's root when searching for extents.
Cloning is not allowed to cross vfsmounts, ie. when two subvolumes from
one filesystem are mounted separately.
Signed-off-by: David Sterba <dsterba@suse.cz>
The clk patches added code to get and enable clocks in the
respective driver probe functions. If the probe function failed
for some reason after enabling the clock, the clock was not
disabled again in many cases.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lumm <andrew@lunn.ch>
The last argument of orion_ge00_init() is actually the error
interrupt, so we should be using the correct value here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Commit 98d9986 (ARM: Kirkwood: Replace clock gating) and the fix 5fb2ce
(ARM: Kirkwood: clk_register_gate_fn: add fn assignment) introduced a custom
variant of clock gating which allows to define a function to be called
before gating the clock off.
This is used to disable the SATA and PCIe PHYs if the respective clocks
are unused after initialization.
However, of these two drivers, the SATA driver may be compiled as a module.
The driver re-enables the clocks at module init but the PHYs stay disabled.
Since the custom clock gating disabled the PHYs when gating the clock off,
it should also re-enable them when enabling the clock gate. This is done by
adding a second function that may be used to enable the PHYs.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Marvell engineers tell us:
It seems that many units use the RUNIT clock.
SPI, UART, NAND, TWSI, ...
So it's not possible to clock gate it.
Currently the SPI, NAND and TWSI driver will clk_prepaure_enable()
this clk, but since we have no idea what ... is, and turning this clk
off results in a hard lock, unconditionally enable runit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Due to automatic merge of a613163dff04cbfcb7d66b06ef4a5f65498ee59b
"ARM: integrator: convert to common clock" and
56a34b03ff427046494db87f05fc810aaedd23a5 "ARM: versatile: Make
plat-versatile clock optional" two platforms: Integrator and
Versatile Express now select both COMMON_CLK and
PLAT_VERSATILE_CLOCK which breaks building them. Fixed now.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The merge of the 'clk-for-linus' branch caused an automated
merge failure. Pull that in here so we can fix the problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We now refuse to load on gen6+ if kms is not enabled:
commit 26394d9251879231b85e6c8cf899fa43e75c68f1
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Mar 26 21:33:18 2012 +0200
drm/i915: refuse to load on gen6+ without kms
Which results in the drm core calling our lastclose function to clean
up the mess, but that one is neatly broken for such failure cases
since kms has been introduced in
commit 79e539453b34e35f39299a899d263b0a1f1670bd
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Nov 7 14:24:08 2008 -0800
DRM: i915: add mode setting support
Reported-and-tested-by: Paulo Zanoni <przanoni@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes failures in transform feedback on gen7 because our SOL_RESET
flag was setting the transform feedback offsets in the old context
(occasionally happened to be ours) instead of the new context.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
LVDS is the first output where dpms on/off and prepare/commit don't
perfectly match. Now the idea behind this special case seems to be
that for simple resolution changes on the LVDS we don't need to stop
the pipe, because (at least on newer chips) we can adjust the panel
fitter on the fly.
There are a few problems with the current code though:
- We still stop and restart the pipe unconditionally, because the crtc
helper code isn't flexible enough.
- We show some ugly flickering, especially when changing crtcs (this
the crtc helper would actually take into account, but we don't
implement the encoder->get_crtc callback required to make this work
properly).
So it doesn't even work as advertised. I agree that it would be nice
to do resolution changes on LVDS (and also eDP) whithout blacking the
screen where the panel fitter allows to do that. But imo we should
implement this as a special case a few layers up in the mode set code,
akin to how we already detect simple framebuffer changes (and only
update the required registers with ->mode_set_base).
Until this is all in place, make our lives easier and just rip it out.
Also note that this seems to fix actual bugs with enabling the lvds
output, see:
http://lists.freedesktop.org/archives/intel-gfx/2012-July/018614.html
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Giacomo Comes <comes@naic.edu>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to check that "ctx" is a valid pointer before dereferencing it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we end up trying to unpin a freed object and BUG.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This prevents a WARN introduced with
commit de2b998552c1534e87bfbc51ec5734b02bc89020
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jul 4 22:52:50 2012 +0200
drm/i915: don't return a spurious -EIO from intel_ring_begin
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The issue is that we stale data in the CPU caches, when we come to
swap-out the object, the CPU may short-circuit the reads from those
cacheline and so corrupt the context object.
Secondary, leaving the context object as being marked in the CPU write
domain whilst on the GPU active list is a bad idea and will throw
warnings later.
Note: Thanks to calling set_to_gtt_domain with write = false and not
setting any gpu write domain when putting a context object onto the
active list (when we switch away from it) the set_to_gtt_domain call
won't block.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Added a note to the commit message and a comment in the code
to explain the clever non-blocking trick.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
