* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (61 commits)
sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes
sysfs: make directory dentries and inodes reclaimable
sysfs: implement sysfs_get_dentry()
sysfs: move sysfs_drop_dentry() to dir.c and make it static
sysfs: restructure add/remove paths and fix inode update
sysfs: use sysfs_mutex to protect the sysfs_dirent tree
sysfs: consolidate sysfs spinlocks
sysfs: make kobj point to sysfs_dirent instead of dentry
sysfs: implement sysfs_find_dirent() and sysfs_get_dirent()
sysfs: implement SYSFS_FLAG_REMOVED flag
sysfs: rename sysfs_dirent->s_type to s_flags and make room for flags
sysfs: make sysfs_drop_dentry() access inodes using ilookup()
sysfs: Fix oops in sysfs_drop_dentry on x86_64
sysfs: use singly-linked list for sysfs_dirent tree
sysfs: slim down sysfs_dirent->s_active
sysfs: move s_active functions to fs/sysfs/dir.c
sysfs: fix root sysfs_dirent -> root dentry association
sysfs: use iget_locked() instead of new_inode()
sysfs: reorganize sysfs_new_indoe() and sysfs_create()
sysfs: fix parent refcounting during rename and move
...
This driver has been broken forever. It depends on i2c-algo-8xx which
has never been in the mainline kernel.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Work around a problem reported on:
http://ozlabs.org/pipermail/linuxppc-embedded/2005-July/019038.html
Without this patch I2C on mpc5200 becomes unusable after a while.
Tested on mpc5200 boards by Matthias Fechner and me.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add TWI driver for the PMC-Sierra MSP71xx devices.
[JD: Drop the probe hack, don't set algo_data as we never use it, return
the right error code if the driver registration fails.]
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There's some redundancy in the tsl2550 initialization sequence. It is
powering up the device twice, and setting the operating mode twice
too. Setting things just once saves SMBus transactions, which aren't
always cheap, speeding up the device initialization.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
This is a new I2C bus driver for the TAOS evaluation modules. Developped
and tested on the TAOS TSL2550 EVM.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add an ability to utilize the internal SRAM buffer on ICH4
and newer host controllers to speed up execution of block operations.
I've split the code so that it is more clear which block transaction is
performed.
First of all the host controller's type is identified. isich4 is set when
we think that the controller has the internal buffer. Then, before every
block transaction, if isich4 is set, we attempt to enable the E32B bit in
SMBAUXCTL register.
Signed-off-by: Oleg Ryjkov <olegr@google.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* Use defines instead of raw numbers for register bits
* Fix several wrong indentations and trailing whitespace
* Move hwpec timeout checking to a separate function
Signed-off-by: Oleg Ryjkov <olegr@google.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_gpio_getsda() and i2c_gpio_getscl() are only used in this file.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use i2c_bit_add_numbered_bus() so that the i2c-gpio adapter works well
with new-style pre-declared devices.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update the IOP3xx I2C driver to use i2c_add_numbered_adapter(), so that
later patches can convert boards to using new-style drivers.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Tested-by: Voipio Riku <Riku.Voipio@movial.fi>
Cc: Dan J Williams <dan.j.williams@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the i2c-sis5595 driver release its PCI device after registering.
This is to allow the sis5595 hardware monitoring driver to also
access this PCI device. The same trick is already used in the
i2c-viapro and via686a drivers to let them both load.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for SMBus block read/write transactions to i2c-nforce2
driver, in particular to host controllers MCP51 and MCP55.
Signed-off-by: Oleg Ryjkov <olegr@google.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the i2c-mpc driver over to using the new i2c infrastructure.
Specifically, it now uses i2c_add_numbered_adapter so that the bus number
can be determined ahead of time and used to register i2c clients before
the bus is instantiated.
Tested on an MPC5200 based board
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the Marvell mv64xxx I2C driver to use the new i2c infrastructure,
by calling i2c_add_numbered_adapter(). This allows clients to be
registered before the bus is instantiated.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
A driver for the Dallas DS1682 elapsed time recorder chip.
Tested on a MPC5200 based board using the integrated i2c adapter.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the drivers specify how many bytes they want to read with
i2c_smbus_read_i2c_block_data(). So far, the block count was
hard-coded to I2C_SMBUS_BLOCK_MAX (32), which did not make much sense.
Many driver authors complained about this before, and I believe it's
about time to fix it. Right now, authors have to do technically stupid
things, such as individual byte reads or full-fledged I2C messaging,
to work around the problem. We do not want to encourage that.
I even found that some bus drivers (e.g. i2c-amd8111) already
implemented I2C block read the "right" way, that is, they didn't
follow the old, broken standard. The fact that it was never noticed
before just shows how little i2c_smbus_read_i2c_block_data() was used,
which isn't that surprising given how broken its prototype was so far.
There are some obvious compatiblity considerations:
* This changes the i2c_smbus_read_i2c_block_data() prototype. Users
outside the kernel tree will notice at compilation time, and will
have to update their code.
* User-space has access to i2c_smbus_xfer() directly using i2c-dev, so
the changed expectations would affect tools such as i2cdump. In order
to preserve binary compatibility, we give I2C_SMBUS_I2C_BLOCK_DATA
a new numeric value, and define I2C_SMBUS_I2C_BLOCK_BROKEN with the
old numeric value. When i2c-dev receives a transaction with the
old value, it can convert it to the new format on the fly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We have a new RTC subsystem with better drivers.
Legacy driver status:
* ds1337: The DS1337 and DS1339 are now supported by the rtc-ds1307
driver, so it looks to me like we could even delete the ds1337
driver right away.
* ds1374: Will soon be replaced with Scott Wood's rtc-ds1374 driver.
* m41t00: The M41T00 is supported by the rtc-ds1307 driver. For the
M41T81 and M41T85, the rtc-m41t80 driver written by Atsushi Nemoto
should work.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: James Chapman <jchapman@katalix.com>
Cc: Randy Vinson <rvinson@mvista.com>
The scx200_acb driver use a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Generate I2C kerneldoc; fix various glitches and add "context" sections to
that documentation. Most I2C and SMBus functions still have no kerneldoc.
Let me suggest providing kerneldoc for all the i2c_smbus_*() functions as
a small and mostly self-contained project for anyone so inclined. :)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Well, first of all, I don't want to change so many files either.
What I do:
Adding a new parameter "struct bin_attribute *" in the
.read/.write methods for the sysfs binary attributes.
In fact, only the four lines change in fs/sysfs/bin.c and
include/linux/sysfs.h do the real work.
But I have to update all the files that use binary attributes
to make them compatible with the new .read and .write methods.
I'm not sure if I missed any. :(
Why I do this:
For a sysfs attribute, we can get a pointer pointing to the
struct attribute in the .show/.store method,
while we can't do this for the binary attributes.
I don't know why this is different, but this does make it not
so handy to use the binary attributes as the regular ones.
So I think this patch is reasonable. :)
Who benefits from it:
The patch that exposes ACPI tables in sysfs
requires such an improvement.
All the table binary attributes share the same .read method.
Parameter "struct bin_attribute *" is used to get
the table signature and instance number which are used to
distinguish different ACPI table binary attributes.
Without this parameter, we need to offer different .read methods
for different ACPI table binary attributes.
This is impossible as there are various ACPI tables on different
platforms, and we don't know what they are until they are loaded.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs is now completely out of driver/module lifetime game. After
deletion, a sysfs node doesn't access anything outside sysfs proper,
so there's no reason to hold onto the attribute owners. Note that
often the wrong modules were accounted for as owners leading to
accessing removed modules.
This patch kills now unnecessary attribute->owner. Note that with
this change, userland holding a sysfs node does not prevent the
backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the
following message.
http://article.gmane.org/gmane.linux.kernel/510293
(tweaked by Greg to not delete the field just yet, to make it easier to
merge things properly.)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using lockdep validator causes warnings like
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
[<c00241a0>] (dump_stack+0x0/0x14) from [<c00520f8>] (__lock_acquire+0x150/0xc40)
[<c0051fa8>] (__lock_acquire+0x0/0xc40) from [<c00530a0>] (lock_acquire+0x5c/0x70)
[<c0053044>] (lock_acquire+0x0/0x70) from [<c01d9e44>] (_spin_lock_irq+0x48/0x58)
r7:c07e5144 r6:00000000 r5:c015fb94 r4:c07e50b8
[<c01d9dfc>] (_spin_lock_irq+0x0/0x58) from [<c015fb94>] (i2c_pxa_xfer+0x110/0x2e0)
r5:c07e50b8 r4:0000001f
This is caused by memcpy'ing a statical initialized spin-lock. This patch
removes a static pxa_i2c structure which was used only as a source for this
memcpy() operation. Instead of, members and the spinlock will be
initialized manually.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix for the following build warning:
CC drivers/i2c/busses/i2c-s3c2410.o
drivers/i2c/busses/i2c-s3c2410.c: In function 's3c24xx_i2c_probe':
drivers/i2c/busses/i2c-s3c2410.c:839: warning: format '%ld' expects type 'long int', but argument 4 has type 'resource_size_t'
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Prevent legacy drivers from issuing uevents for device creation/removal,
so that userspace can't cause modprobing loops for them. This became a
problem for some legacy PC drivers. I can't easily see it becoming an
issue with I2C legacy drivers, but consistency-in-paranoia seems likely
to be a good thing here. For usable i2c-level driver model uevents, just
switch to a new-style driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] update default configuration.
[S390] Kconfig: no wireless on s390.
[S390] Kconfig: use common Kconfig files for s390.
[S390] Kconfig: common config options for s390.
[S390] Kconfig: unwanted menus for s390.
[S390] Kconfig: menus with depends on HAS_IOMEM.
[S390] Kconfig: refine depends statements.
[S390] Avoid compile warning.
[S390] qdio: re-add lost perf_stats.tl_runs change in qdio_handle_pci
[S390] Avoid sparse warnings.
[S390] dasd: Fix modular build.
[S390] monreader inlining cleanup.
[S390] cio: Make some structures and a function static.
[S390] cio: Get rid of _ccw_device_get_device_number().
[S390] fix subsystem removal fallout
CC drivers/i2c/busses/i2c-at91.o
drivers/i2c/busses/i2c-at91.c: In function 'at91_i2c_probe':
drivers/i2c/busses/i2c-at91.c:213: warning: implicit declaration of function 'IS_ERR'
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make i2c-at91 register as i2c adapter zero (none of these chips seem to
have more than one TWI controllers) to let it kick in any board-specific
device declarations; also make it hotplug/coldplug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From commit 7d054817b7:
> According to the PXA27x developer's manual, we shall do so.
We shall also at least compile test our changes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[ With Johannes Berg <johannes@sipsolutions.net> ]
Separate the hibernation (aka suspend to disk code) from the other suspend
code. In particular:
* Remove the definitions related to hibernation from include/linux/pm.h
* Introduce struct hibernation_ops and a new hibernate() function to hibernate
the system, defined in include/linux/suspend.h
* Separate suspend code in kernel/power/main.c from hibernation-related code
in kernel/power/disk.c and kernel/power/user.c (with the help of
hibernation_ops)
* Switch ACPI (the only user of pm_ops.pm_disk_mode) to hibernation_ops
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update some of the layered parport_driver code to use parport->dev:
- i2c-parport (parent of i2c_adapter)
- spi_butterfly (parent of spi_master, allowing cruft removal)
- lp (creating class_device)
- ppdev (parent of parportN device)
- tipar (creating class_device)
There are still drivers that should be updated, like some of the input
drivers; but they won't be any worse off than they are today.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove software_suspend() and all its users since
pm_suspend(PM_SUSPEND_DISK) should be equivalent and there's no point in
having two interfaces for the same thing.
The patch also changes the valid_state function to return 0 (false) for
PM_SUSPEND_DISK when SOFTWARE_SUSPEND is not configured instead of
accepting it and having the whole thing fail later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (59 commits)
PCI: Free resource files in error path of pci_create_sysfs_dev_files()
pci-quirks: disable MSI on RS400-200 and RS480
PCI hotplug: Use menuconfig objects
PCI: ZT5550 CPCI Hotplug driver fix
PCI: rpaphp: Remove semaphores
PCI: rpaphp: Ensure more pcibios_add/pcibios_remove symmetry
PCI: rpaphp: Use pcibios_remove_pci_devices() symmetrically
PCI: rpaphp: Document is_php_dn()
PCI: rpaphp: Document find_php_slot()
PCI: rpaphp: Rename rpaphp_register_pci_slot() to rpaphp_enable_slot()
PCI: rpaphp: refactor tail call to rpaphp_register_slot()
PCI: rpaphp: remove rpaphp_set_attention_status()
PCI: rpaphp: remove print_slot_pci_funcs()
PCI: rpaphp: Remove setup_pci_slot()
PCI: rpaphp: remove a call that does nothing but a pointer lookup
PCI: rpaphp: Remove another wrappered function
PCI: rpaphp: Remve another call that is a wrapper
PCI: rpaphp: remove a function that does nothing but wrap debug printks
PCI: rpaphp: Remove un-needed goto
PCI: rpaphp: Fix a memleak; slot->location string was never freed
...
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When compiled as a module, the i2c-s3c2410 driver does not
free either the IRQ or the i2c adapter it attached to the system.
As part of this fix, move to the usual kernel style
of freeing items as part of the probe error path
making the remove process easier.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix the setup time for SDA to SCL due to the way
the S3C24XX I2C controller works.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add a driver for the i2c-tiny-usb interface. This is a simple
do-it-yourself USB to I2C interface targeted at experimental and
home use. See the i2c-tiny-usb homepage for hardware details:
http://www.harbaum.org/till/i2c_tiny_usb
Signed-off-by: Till Harbaum <till@harbaum.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new generic i2c-gpio driver should be used instead.
The obsolete drivers will be removed in September 2007.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Deepak Saxena <dsaxena@plexity.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Platform driver for the Simtec CPLD based simple I2C logic.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a very simple bitbanging I2C bus driver utilizing the new
arch-neutral GPIO API. Useful for chips that don't have a built-in
I2C controller, additional I2C busses, or testing purposes.
To use, include something similar to the following in the
board-specific setup code:
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
.sda_pin = GPIO_PIN_FOO,
.scl_pin = GPIO_PIN_BAR,
};
static struct platform_device i2c_gpio_device = {
.name = "i2c-gpio",
.id = 0,
.dev = {
.platform_data = &i2c_gpio_data,
},
};
Register this platform_device, set up the I2C pins as GPIO if
required and you're ready to go. This will use default values for
udelay and timeout, and will work with GPIO hardware that does not
support open drain mode, but allows sensing of the SDA and SCL lines
even when they are being driven.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow the whole I2C menu to be disabled at once without diving into
the submenus for deselecting all options (should the user desire so).
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add back the i2c_smbus_read_block_data helper function, it is needed
by the upcoming lm93 hardware monitoring driver and possibly others.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It was reported to me that the i2c-pxa driver was not able to process
more that 50 transactions per second. Investigation revealed that the
I2C unit was busy for 20 ms after every transaction. The reason seems
to be that we forget to clear the STOP and ACKNACK bits at the end of
the transaction. According to the PXA27x developer's manual, we shall
do so.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Nicolas Pitre <nico@cam.org>
Improve the debugging features of the i2c-algo-bit driver:
* Make it possible to compile the driver without debugging support
at all, making it much smaller.
* Use dev_dbg() for debugging messages where possible, and dev_err()
for error messages.
* Remove redundant debugging messages.
These changes allowed for minor code cleanups, which are included
as well.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The original i2c-algo-bit implementation uses a 33/66 SCL duty cycle
when bits are being written on the bus. While the I2C specification
doesn't forbid it, this prevents us from driving the I2C bus to its
max speed, limiting us to 66 kbps max on standard I2C busses.
Implementing a 50/50 duty cycle instead lets us max out the bandwidth
up to the theoretical max of 100 kbps on standard I2C busses. This is
particularly important when large amounts of data need to be transfered
over the bus, as is the case with some TV adapters when the firmware is
being uploaded.
In fact this change even allows, at least in theory, fast-mode I2C
support at 125, 166 and 250 kbps. There's no way to reach the
theoretical max of 400 kbps with this implementation. But I don't
think we want to put efforts in that direction anyway: software-driven
I2C is very CPU-intensive and bad for latency.
Other timing changes:
* Don't set SDA high explicitly on error, we're going to issue a stop
condition before we leave anyway.
* If an error occurs when sending the slave address, yield the CPU
before retrying, and remove the additional delay after the new start
condition.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update the OMAP I2C driver to use i2c_add_numbered_adapter(), so that
later patches can convert boards to using new-style drivers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c linux driver for blackfin architecture which supports blackfin
on-chip TWI controller i2c operation.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Reviewed-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Make i2c_del_driver a void function, like all other driver removal
functions. It always returned 0 even when errors occured, and nobody
ever actually checked the return value anyway. And we cannot fail
a module removal anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the declaration of i2c-isa-only exported symbols to i2c-isa
itself, that's the best way to ensure nobody will attempt to use them.
Hopefully we'll get rid of the exports themselves soon anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add a new helper function to instantiate an i2c device. It is meant as a
replacement for i2c_new_device() when you don't know for sure at which
address your I2C/SMBus device lives. This happens frequently on TV
adapters for example, you know there is a tuner chip on the bus, but
depending on the exact board model and revision, it can live at different
addresses. So, the new i2c_new_probed_device() function will probe the bus
according to a list of addresses, and as soon as one of these addresses
responds, it will call i2c_new_device() on that one address.
This function will make it possible to port the old i2c drivers to the
new model quickly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add i2c_bit_add_numbered_bus(), which is equivalent to i2c_bit_add_bus
except that it calls i2c_add_numbered_adapter() at the end instead of
i2c_add_adapter().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Make i2c-core.c obey Documentation/CodingStyle better by snugging
the EXPORT_SYMBOL declarations next to the relevant definitions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This adds a call, i2c_add_numbered_adapter(), registering an I2C adapter
with a specific bus number and then creating I2C device nodes for any
pre-declared devices on that bus. It builds on previous patches adding
I2C probe() and remove() support, and that pre-declaration of devices.
This completes the core support for "new style" I2C device drivers.
Those follow the standard driver model for binding devices to drivers
(using probe and remove methods) rather than a legacy model (where the
driver tries to autoconfigure each bus, and registers devices itself).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This provides partial support for new-style I2C driver binding. It builds
on "struct i2c_board_info" declarations that identify I2C devices on a given
board. This is needed on systems with I2C devices that can't be fully probed
and/or autoconfigured, such as many embedded Linux configurations where the
way a given I2C device is wired may affect how it must be used.
There are two models for declaring such devices:
* LATE -- using a public function i2c_new_device(). This lets modules
declare I2C devices found *AFTER* a given I2C adapter becomes available.
For example, a PCI card could create adapters giving access to utility
chips on that card, and this would be used to associate those chips with
those adapters.
* EARLY -- from arch_initcall() level code, using a non-exported function
i2c_register_board_info(). This copies the declarations *BEFORE* such
an i2c_adapter becomes available, arranging that i2c_new_device() will
be called later when i2c-core registers the relevant i2c_adapter.
For example, arch/.../.../board-*.c files would declare the I2C devices
along with their platform data, and I2C devices would behave much like
PNPACPI devices. (That is, both enumerate from board-specific tables.)
To match the exported i2c_new_device(), the previously-private function
i2c_unregister_device() is now exported.
Pending later patches using these new APIs, this is effectively a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
More update for new style driver support: add a remove() method, and
use it in the relevant code paths.
Again, nothing will use this yet since there's nothing to create devices
feeding this infrastructure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
One of a series of I2C infrastructure updates to support enumeration using
the standard Linux driver model.
This patch updates probe() and associated hotplug/coldplug support, but
not remove(). Nothing yet _uses_ it to create I2C devices, so those
hotplug/coldplug mechanisms will be the only externally visible change.
This patch will be an overall NOP since the I2C stack doesn't yet create
clients/devices except as part of binding them to legacy drivers.
Some code is moved earlier in the source code, helping group more of the
per-device infrastructure in one place and simplifying handling per-device
attributes.
Terminology being adopted: "legacy drivers" create devices (i2c_client)
themselves, while "new style" ones follow the driver model (the i2c_client
is handed to the probe routine). It's an either/or thing; the two models
don't mix, and drivers that try mixing them won't even be registered.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Port the i2c-pca-isa driver to the new device driver model. I'm
using Rene Herman's new isa bus type, as it fits the needs nicely. One
benefit is that we can now give a proper parent to our i2c adapter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Port the i2c-elektor driver to the new device driver model. I'm
using Rene Herman's new isa bus type, as it fits the needs nicely. One
benefit is that we can now give a proper parent to our i2c adapter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When unloading the driver, we really want to unregister the i2c adapter
before we power it off, rather than the other way around.
Also speed up the bus a bit when we can sense SCL. The slaves will
stretch the line as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The scx200_acb driver supports two kind of devices, PCI ones and ISA
ones. Even ISA ones are detected using the presence of a given PCI
device, and we get a reference to it, but never put it back, so we
have a leak. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Initialize the fields of the i2c_adapter structure individually,
rather than copying a whole static template structure. This shaves
off 474 bytes or 14% (on i386) from the binary size.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Now that i2c-core lets the i2c bus drivers emulate the SMBus block read
and SMBus block process call transaction types, let's implement that in
the popular i2c bit-banging driver. This will also act as a reference
implementation for other bus drivers which want to do the same.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the I2C bus drivers emulate the SMBus Block Read and Block Process
Call transactions if they wish. This requires to define a new message
flag, which i2c-core will use to let the underlying I2C bus driver
know that the first received byte will specify the length of the read
message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c-algo-bit driver doesn't behave well on read errors: it'll
bail out without even sending a stop condition on the bus, so the bus
will be stuck. So make sure that we always send a stop condition on
the bus before we leave. The best way to make sure is to always send
it at the end of function bit_xfer.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Rename dev_to_i2c_adapter() as to_i2c_adapter(), since the previous
syntax was a surprising and needless difference from normal naming
conventions in Linux.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch is a minor cleanup/code shrink, using class infrastructure
in i2c-core to manage the i2c_adapter attribute.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This shrinks the size of "struct i2c_client" by 40 bytes:
- Substantially shrinks the string used to identify the chip type
- The "flags" don't need to be so big
- Removes some internal padding
It also adds kerneldoc for that struct, explaining how "name" is really a
chip type identifier; it's otherwise potentially confusing.
Because the I2C_NAME_SIZE symbol was abused for both i2c_client.name
and for i2c_adapter.name, this needed to affect i2c_adapter too. The
adapters which used that symbol now use the more-obviously-correct
idiom of taking the size of that field.
JD: Shorten i2c_adapter.name from 50 to 48 bytes while we're here, to
avoid wasting space in padding.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Minor cleanup in i2c_register_driver(): use list_for_each_entry().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Kill i2c_adapter_driver as it doesn't make sense and it prevents
further i2c-core cleanups. i2c_adapter devices are virtual devices
(ex-class devices) and as such they don't need a driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Kill i2c_adapter.class_dev. Instead, set the class of i2c_adapter.dev
to i2c_adapter_class, so that a symlink will be created for every
i2c_adapter in /sys/class/i2c-adapter.
The same change must be mirrored to i2c-isa as it duplicates some
of the i2c-core functionalities.
User-space tools and libraries might need some adjustments. In
particular, libsensors from lm_sensors 2.10.3 or later is required for
proper discovery of i2c adapter names after this change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reposted patch for kernel 2.6.21-rc2.
The driver i2c-pxa doesn't set the class member in i2c_adapter, which
is used to register the I2C adapter. The hwmon (sensors) drivers (e.g.
adm1021) that are connected to a i2c-pxa adapter don't attach because
they expect that the adapter supports class I2C_CLASS_HWMON.
This patch adds functionality to allow platforms to set the class and
pass it as platform_data to the i2c-pxa driver. Sample usage in
platform code:
static struct i2c_pxa_platform_data my_i2c_platform_data = {
.class = I2C_CLASS_HWMON
};
static void __init my_platform_init(void)
{
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
pxa_set_i2c_info(&my_i2c_platform_data);
}
Signed-off-by: Matej Kenda <matej.kenda@hermes-softlab.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Last write during i2c_xfer is of the wrong byte (off-by-1).
* Read length is wrong for some of the reads (mistakenly used the PEC
version)
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Looks like a local change I made to be able to test-compile the i2c-pasemi
driver leaked upstream.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check if workqueue creation failed. Further usage of NULL pointed
workqueue is not good I guess ;)
Signed-off-by: Cyrill V. Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Restore the original host configuration on driver unload and on
suspend. In particular this returns the SMBus master in I2C mode if it
was originally in I2C mode, which should help with suspend/resume if
the BIOS expects to find the SMBus master in I2C mode.
This fixes bug #6449 (for real this time.)
http://bugzilla.kernel.org/show_bug.cgi?id=6449
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Tommi Kyntola <tommi.kyntola@ray.fi>
Move the Acorn IOC/IOMD I2C bus driver from drivers/i2c, strip
out the reminants of the platform specific parts of the old
PCF8583 RTC code, and remove the old obsolete PCF8583 driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable svc access to cp6 via an undefined instruction hook. Do not enable
access for usr code.
This patch also makes iop13xx select PLAT_IOP, this requires a small change
to drivers/i2c/busses/i2c-iop3xx.c.
Per Lennert Buytenhek's note, the cp6 trap routine is moved to arch/arm/plat-iop
Per Nicolas Pitre's note, the cp_wait is skipped since the latency to
return to the faulting function is longer than cp_wait.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the i2c_adapter migration plan changed and we are going to
keep i2c_adapter.dev, it's no longer that urgent to add a proper device
to all i2c_adapter drivers. Thus is seems resonable to degrade the
warning asking authors to migrate their driver to a debug message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Declare the parent device of i2c_adapter devices each time we can
easily do so. It makes the i2c_adapter appear at the right place in
the device tree, rather than as a platform device.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: v4l-dvb-maintainer@linuxtv.org
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
